linux/drivers/gpu/drm/i915/display/intel_cx0_phy.c

3651 lines
105 KiB
C
Raw Permalink Normal View History

drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
// SPDX-License-Identifier: MIT
/*
* Copyright © 2023 Intel Corporation
*/
#include <linux/log2.h>
#include <linux/math64.h>
#include <drm/drm_print.h>
#include "i915_utils.h"
#include "intel_alpm.h"
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
#include "intel_cx0_phy.h"
#include "intel_cx0_phy_regs.h"
#include "intel_ddi.h"
#include "intel_ddi_buf_trans.h"
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
#include "intel_de.h"
#include "intel_display_types.h"
#include "intel_dp.h"
#include "intel_hdmi.h"
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
#include "intel_panel.h"
#include "intel_psr.h"
#include "intel_snps_hdmi_pll.h"
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
#include "intel_tc.h"
#define MB_WRITE_COMMITTED true
#define MB_WRITE_UNCOMMITTED false
#define for_each_cx0_lane_in_mask(__lane_mask, __lane) \
for ((__lane) = 0; (__lane) < 2; (__lane)++) \
for_each_if((__lane_mask) & BIT(__lane))
#define INTEL_CX0_LANE0 BIT(0)
#define INTEL_CX0_LANE1 BIT(1)
#define INTEL_CX0_BOTH_LANES (INTEL_CX0_LANE1 | INTEL_CX0_LANE0)
bool intel_encoder_is_c10phy(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
/* PTL doesn't have a PHY connected to PORT B; as such,
* there will never be a case where PTL uses PHY B.
* WCL uses PORT A and B with the C10 PHY.
* Reusing the condition for WCL and extending it for PORT B
* should not cause any issues for PTL.
*/
if (display->platform.pantherlake && phy < PHY_C)
return true;
if ((display->platform.lunarlake || display->platform.meteorlake) && phy < PHY_C)
return true;
return false;
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
static int lane_mask_to_lane(u8 lane_mask)
{
if (WARN_ON((lane_mask & ~INTEL_CX0_BOTH_LANES) ||
hweight8(lane_mask) != 1))
return 0;
return ilog2(lane_mask);
}
static u8 intel_cx0_get_owned_lane_mask(struct intel_encoder *encoder)
{
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
if (!intel_tc_port_in_dp_alt_mode(dig_port))
return INTEL_CX0_BOTH_LANES;
/*
* In DP-alt with pin assignment D, only PHY lane 0 is owned
* by display and lane 1 is owned by USB.
*/
return intel_tc_port_max_lane_count(dig_port) > 2
? INTEL_CX0_BOTH_LANES : INTEL_CX0_LANE0;
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
static void
assert_dc_off(struct intel_display *display)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
bool enabled;
enabled = intel_display_power_is_enabled(display, POWER_DOMAIN_DC_OFF);
drm_WARN_ON(display->drm, !enabled);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_cx0_program_msgbus_timer(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
int lane;
for_each_cx0_lane_in_mask(INTEL_CX0_BOTH_LANES, lane)
intel_de_rmw(display,
XELPDP_PORT_MSGBUS_TIMER(display, encoder->port, lane),
XELPDP_PORT_MSGBUS_TIMER_VAL_MASK,
XELPDP_PORT_MSGBUS_TIMER_VAL);
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* Prepare HW for CX0 phy transactions.
*
* It is required that PSR and DC5/6 are disabled before any CX0 message
* bus transaction is executed.
*
* We also do the msgbus timer programming here to ensure that the timer
* is already programmed before any access to the msgbus.
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
*/
static intel_wakeref_t intel_cx0_phy_transaction_begin(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
intel_wakeref_t wakeref;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_psr_pause(intel_dp);
wakeref = intel_display_power_get(display, POWER_DOMAIN_DC_OFF);
intel_cx0_program_msgbus_timer(encoder);
return wakeref;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_cx0_phy_transaction_end(struct intel_encoder *encoder, intel_wakeref_t wakeref)
{
struct intel_display *display = to_intel_display(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
intel_psr_resume(intel_dp);
intel_display_power_put(display, POWER_DOMAIN_DC_OFF, wakeref);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_clear_response_ready_flag(struct intel_encoder *encoder,
int lane)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
intel_de_rmw(display,
XELPDP_PORT_P2M_MSGBUS_STATUS(display, encoder->port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
0, XELPDP_PORT_P2M_RESPONSE_READY | XELPDP_PORT_P2M_ERROR_SET);
}
static void intel_cx0_bus_reset(struct intel_encoder *encoder, int lane)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_de_write(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_RESET);
if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_RESET,
XELPDP_MSGBUS_TIMEOUT_SLOW)) {
drm_err_once(display->drm,
"Failed to bring PHY %c to idle.\n",
phy_name(phy));
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return;
}
intel_clear_response_ready_flag(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static int intel_cx0_wait_for_ack(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int command, int lane, u32 *val)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_de_wait_custom(display,
XELPDP_PORT_P2M_MSGBUS_STATUS(display, port, lane),
XELPDP_PORT_P2M_RESPONSE_READY,
XELPDP_PORT_P2M_RESPONSE_READY,
XELPDP_MSGBUS_TIMEOUT_FAST_US,
XELPDP_MSGBUS_TIMEOUT_SLOW, val)) {
drm_dbg_kms(display->drm,
"PHY %c Timeout waiting for message ACK. Status: 0x%x\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), *val);
if (!(intel_de_read(display, XELPDP_PORT_MSGBUS_TIMER(display, port, lane)) &
XELPDP_PORT_MSGBUS_TIMER_TIMED_OUT))
drm_dbg_kms(display->drm,
"PHY %c Hardware did not detect a timeout\n",
phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -ETIMEDOUT;
}
if (*val & XELPDP_PORT_P2M_ERROR_SET) {
drm_dbg_kms(display->drm,
"PHY %c Error occurred during %s command. Status: 0x%x\n",
phy_name(phy),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
command == XELPDP_PORT_P2M_COMMAND_READ_ACK ? "read" : "write", *val);
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -EINVAL;
}
if (REG_FIELD_GET(XELPDP_PORT_P2M_COMMAND_TYPE_MASK, *val) != command) {
drm_dbg_kms(display->drm,
"PHY %c Not a %s response. MSGBUS Status: 0x%x.\n",
phy_name(phy),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
command == XELPDP_PORT_P2M_COMMAND_READ_ACK ? "read" : "write", *val);
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -EINVAL;
}
return 0;
}
static int __intel_cx0_read_once(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane, u16 addr)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int ack;
u32 val;
if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING,
XELPDP_MSGBUS_TIMEOUT_SLOW)) {
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Timeout waiting for previous transaction to complete. Reset the bus and retry.\n", phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -ETIMEDOUT;
}
intel_de_write(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING |
XELPDP_PORT_M2P_COMMAND_READ |
XELPDP_PORT_M2P_ADDRESS(addr));
ack = intel_cx0_wait_for_ack(encoder, XELPDP_PORT_P2M_COMMAND_READ_ACK, lane, &val);
if (ack < 0)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return ack;
intel_clear_response_ready_flag(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* FIXME: Workaround to let HW to settle
* down and let the message bus to end up
* in a known state
*/
if (DISPLAY_VER(display) < 30)
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return REG_FIELD_GET(XELPDP_PORT_P2M_DATA_MASK, val);
}
static u8 __intel_cx0_read(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane, u16 addr)
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int i, status;
assert_dc_off(display);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* 3 tries is assumed to be enough to read successfully */
for (i = 0; i < 3; i++) {
status = __intel_cx0_read_once(encoder, lane, addr);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (status >= 0)
return status;
}
drm_err_once(display->drm,
"PHY %c Read %04x failed after %d retries.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), addr, i);
return 0;
}
static u8 intel_cx0_read(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u8 lane_mask, u16 addr)
{
int lane = lane_mask_to_lane(lane_mask);
return __intel_cx0_read(encoder, lane, addr);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static int __intel_cx0_write_once(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane, u16 addr, u8 data, bool committed)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
int ack;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u32 val;
if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING,
XELPDP_MSGBUS_TIMEOUT_SLOW)) {
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Timeout waiting for previous transaction to complete. Resetting the bus.\n", phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -ETIMEDOUT;
}
intel_de_write(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING |
(committed ? XELPDP_PORT_M2P_COMMAND_WRITE_COMMITTED :
XELPDP_PORT_M2P_COMMAND_WRITE_UNCOMMITTED) |
XELPDP_PORT_M2P_DATA(data) |
XELPDP_PORT_M2P_ADDRESS(addr));
if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING,
XELPDP_MSGBUS_TIMEOUT_SLOW)) {
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Timeout waiting for write to complete. Resetting the bus.\n", phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -ETIMEDOUT;
}
if (committed) {
ack = intel_cx0_wait_for_ack(encoder, XELPDP_PORT_P2M_COMMAND_WRITE_ACK, lane, &val);
if (ack < 0)
return ack;
} else if ((intel_de_read(display, XELPDP_PORT_P2M_MSGBUS_STATUS(display, port, lane)) &
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_P2M_ERROR_SET)) {
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Error occurred during write command.\n", phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return -EINVAL;
}
intel_clear_response_ready_flag(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* FIXME: Workaround to let HW to settle
* down and let the message bus to end up
* in a known state
*/
if (DISPLAY_VER(display) < 30)
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
return 0;
}
static void __intel_cx0_write(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane, u16 addr, u8 data, bool committed)
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int i, status;
assert_dc_off(display);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* 3 tries is assumed to be enough to write successfully */
for (i = 0; i < 3; i++) {
status = __intel_cx0_write_once(encoder, lane, addr, data, committed);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (status == 0)
return;
}
drm_err_once(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Write %04x failed after %d retries.\n", phy_name(phy), addr, i);
}
static void intel_cx0_write(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u8 lane_mask, u16 addr, u8 data, bool committed)
{
int lane;
for_each_cx0_lane_in_mask(lane_mask, lane)
__intel_cx0_write(encoder, lane, addr, data, committed);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_c20_sram_write(struct intel_encoder *encoder,
int lane, u16 addr, u16 data)
{
struct intel_display *display = to_intel_display(encoder);
assert_dc_off(display);
intel_cx0_write(encoder, lane, PHY_C20_WR_ADDRESS_H, addr >> 8, 0);
intel_cx0_write(encoder, lane, PHY_C20_WR_ADDRESS_L, addr & 0xff, 0);
intel_cx0_write(encoder, lane, PHY_C20_WR_DATA_H, data >> 8, 0);
intel_cx0_write(encoder, lane, PHY_C20_WR_DATA_L, data & 0xff, 1);
}
static u16 intel_c20_sram_read(struct intel_encoder *encoder,
int lane, u16 addr)
{
struct intel_display *display = to_intel_display(encoder);
u16 val;
assert_dc_off(display);
intel_cx0_write(encoder, lane, PHY_C20_RD_ADDRESS_H, addr >> 8, 0);
intel_cx0_write(encoder, lane, PHY_C20_RD_ADDRESS_L, addr & 0xff, 1);
val = intel_cx0_read(encoder, lane, PHY_C20_RD_DATA_H);
val <<= 8;
val |= intel_cx0_read(encoder, lane, PHY_C20_RD_DATA_L);
return val;
}
static void __intel_cx0_rmw(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane, u16 addr, u8 clear, u8 set, bool committed)
{
u8 old, val;
old = __intel_cx0_read(encoder, lane, addr);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
val = (old & ~clear) | set;
if (val != old)
__intel_cx0_write(encoder, lane, addr, val, committed);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_cx0_rmw(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u8 lane_mask, u16 addr, u8 clear, u8 set, bool committed)
{
u8 lane;
for_each_cx0_lane_in_mask(lane_mask, lane)
__intel_cx0_rmw(encoder, lane, addr, clear, set, committed);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static u8 intel_c10_get_tx_vboost_lvl(const struct intel_crtc_state *crtc_state)
{
if (intel_crtc_has_dp_encoder(crtc_state)) {
if (!intel_crtc_has_type(crtc_state, INTEL_OUTPUT_EDP) &&
(crtc_state->port_clock == 540000 ||
crtc_state->port_clock == 810000))
return 5;
else
return 4;
} else {
return 5;
}
}
static u8 intel_c10_get_tx_term_ctl(const struct intel_crtc_state *crtc_state)
{
if (intel_crtc_has_dp_encoder(crtc_state)) {
if (!intel_crtc_has_type(crtc_state, INTEL_OUTPUT_EDP) &&
(crtc_state->port_clock == 540000 ||
crtc_state->port_clock == 810000))
return 5;
else
return 2;
} else {
return 6;
}
}
void intel_cx0_phy_set_signal_levels(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
struct intel_display *display = to_intel_display(encoder);
const struct intel_ddi_buf_trans *trans;
u8 owned_lane_mask;
intel_wakeref_t wakeref;
int n_entries, ln;
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
if (intel_tc_port_in_tbt_alt_mode(dig_port))
return;
owned_lane_mask = intel_cx0_get_owned_lane_mask(encoder);
wakeref = intel_cx0_phy_transaction_begin(encoder);
trans = encoder->get_buf_trans(encoder, crtc_state, &n_entries);
if (drm_WARN_ON_ONCE(display->drm, !trans)) {
intel_cx0_phy_transaction_end(encoder, wakeref);
return;
}
if (intel_encoder_is_c10phy(encoder)) {
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C10_VDR_CONTROL(1),
0, C10_VDR_CTRL_MSGBUS_ACCESS, MB_WRITE_COMMITTED);
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C10_VDR_CMN(3),
C10_CMN3_TXVBOOST_MASK,
C10_CMN3_TXVBOOST(intel_c10_get_tx_vboost_lvl(crtc_state)),
MB_WRITE_UNCOMMITTED);
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C10_VDR_TX(1),
C10_TX1_TERMCTL_MASK,
C10_TX1_TERMCTL(intel_c10_get_tx_term_ctl(crtc_state)),
MB_WRITE_COMMITTED);
}
for (ln = 0; ln < crtc_state->lane_count; ln++) {
int level = intel_ddi_level(encoder, crtc_state, ln);
int lane = ln / 2;
int tx = ln % 2;
u8 lane_mask = lane == 0 ? INTEL_CX0_LANE0 : INTEL_CX0_LANE1;
if (!(lane_mask & owned_lane_mask))
continue;
intel_cx0_rmw(encoder, lane_mask, PHY_CX0_VDROVRD_CTL(lane, tx, 0),
C10_PHY_OVRD_LEVEL_MASK,
C10_PHY_OVRD_LEVEL(trans->entries[level].snps.pre_cursor),
MB_WRITE_COMMITTED);
intel_cx0_rmw(encoder, lane_mask, PHY_CX0_VDROVRD_CTL(lane, tx, 1),
C10_PHY_OVRD_LEVEL_MASK,
C10_PHY_OVRD_LEVEL(trans->entries[level].snps.vswing),
MB_WRITE_COMMITTED);
intel_cx0_rmw(encoder, lane_mask, PHY_CX0_VDROVRD_CTL(lane, tx, 2),
C10_PHY_OVRD_LEVEL_MASK,
C10_PHY_OVRD_LEVEL(trans->entries[level].snps.post_cursor),
MB_WRITE_COMMITTED);
}
/* Write Override enables in 0xD71 */
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C10_VDR_OVRD,
0, PHY_C10_VDR_OVRD_TX1 | PHY_C10_VDR_OVRD_TX2,
MB_WRITE_COMMITTED);
if (intel_encoder_is_c10phy(encoder))
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C10_VDR_CONTROL(1),
0, C10_VDR_CTRL_UPDATE_CFG, MB_WRITE_COMMITTED);
intel_cx0_phy_transaction_end(encoder, wakeref);
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* Basic DP link rates with 38.4 MHz reference clock.
* Note: The tables below are with SSC. In non-ssc
* registers 0xC04 to 0xC08(pll[4] to pll[8]) will be
* programmed 0.
*/
static const struct intel_c10pll_state mtl_c10_dp_rbr = {
.clock = 162000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0xB4,
.pll[1] = 0,
.pll[2] = 0x30,
.pll[3] = 0x1,
.pll[4] = 0x26,
.pll[5] = 0x0C,
.pll[6] = 0x98,
.pll[7] = 0x46,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xC0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x2,
.pll[16] = 0x84,
.pll[17] = 0x4F,
.pll[18] = 0xE5,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_edp_r216 = {
.clock = 216000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0x4,
.pll[1] = 0,
.pll[2] = 0xA2,
.pll[3] = 0x1,
.pll[4] = 0x33,
.pll[5] = 0x10,
.pll[6] = 0x75,
.pll[7] = 0xB3,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x2,
.pll[16] = 0x85,
.pll[17] = 0x0F,
.pll[18] = 0xE6,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_edp_r243 = {
.clock = 243000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0x34,
.pll[1] = 0,
.pll[2] = 0xDA,
.pll[3] = 0x1,
.pll[4] = 0x39,
.pll[5] = 0x12,
.pll[6] = 0xE3,
.pll[7] = 0xE9,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0x20,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x2,
.pll[16] = 0x85,
.pll[17] = 0x8F,
.pll[18] = 0xE6,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_dp_hbr1 = {
.clock = 270000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0xF4,
.pll[1] = 0,
.pll[2] = 0xF8,
.pll[3] = 0x0,
.pll[4] = 0x20,
.pll[5] = 0x0A,
.pll[6] = 0x29,
.pll[7] = 0x10,
.pll[8] = 0x1, /* Verify */
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xA0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x1,
.pll[16] = 0x84,
.pll[17] = 0x4F,
.pll[18] = 0xE5,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_edp_r324 = {
.clock = 324000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0xB4,
.pll[1] = 0,
.pll[2] = 0x30,
.pll[3] = 0x1,
.pll[4] = 0x26,
.pll[5] = 0x0C,
.pll[6] = 0x98,
.pll[7] = 0x46,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xC0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x1,
.pll[16] = 0x85,
.pll[17] = 0x4F,
.pll[18] = 0xE6,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_edp_r432 = {
.clock = 432000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0x4,
.pll[1] = 0,
.pll[2] = 0xA2,
.pll[3] = 0x1,
.pll[4] = 0x33,
.pll[5] = 0x10,
.pll[6] = 0x75,
.pll[7] = 0xB3,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x1,
.pll[16] = 0x85,
.pll[17] = 0x0F,
.pll[18] = 0xE6,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_dp_hbr2 = {
.clock = 540000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0xF4,
.pll[1] = 0,
.pll[2] = 0xF8,
.pll[3] = 0,
.pll[4] = 0x20,
.pll[5] = 0x0A,
.pll[6] = 0x29,
.pll[7] = 0x10,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xA0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0,
.pll[16] = 0x84,
.pll[17] = 0x4F,
.pll[18] = 0xE5,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_edp_r675 = {
.clock = 675000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0xB4,
.pll[1] = 0,
.pll[2] = 0x3E,
.pll[3] = 0x1,
.pll[4] = 0xA8,
.pll[5] = 0x0C,
.pll[6] = 0x33,
.pll[7] = 0x54,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xC8,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0,
.pll[16] = 0x85,
.pll[17] = 0x8F,
.pll[18] = 0xE6,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_dp_hbr3 = {
.clock = 810000,
.tx = 0x10,
.cmn = 0x21,
.pll[0] = 0x34,
.pll[1] = 0,
.pll[2] = 0x84,
.pll[3] = 0x1,
.pll[4] = 0x30,
.pll[5] = 0x0F,
.pll[6] = 0x3D,
.pll[7] = 0x98,
.pll[8] = 0x1,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0xF0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0,
.pll[16] = 0x84,
.pll[17] = 0x0F,
.pll[18] = 0xE5,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state * const mtl_c10_dp_tables[] = {
&mtl_c10_dp_rbr,
&mtl_c10_dp_hbr1,
&mtl_c10_dp_hbr2,
&mtl_c10_dp_hbr3,
NULL,
};
static const struct intel_c10pll_state * const mtl_c10_edp_tables[] = {
&mtl_c10_dp_rbr,
&mtl_c10_edp_r216,
&mtl_c10_edp_r243,
&mtl_c10_dp_hbr1,
&mtl_c10_edp_r324,
&mtl_c10_edp_r432,
&mtl_c10_dp_hbr2,
&mtl_c10_edp_r675,
&mtl_c10_dp_hbr3,
NULL,
};
/* C20 basic DP 1.4 tables */
static const struct intel_c20pll_state mtl_c20_dp_rbr = {
.clock = 162000,
.tx = { 0xbe88, /* tx cfg0 */
0x5800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x50a8, /* mpllb cfg0 */
0x2120, /* mpllb cfg1 */
0xcd9a, /* mpllb cfg2 */
0xbfc1, /* mpllb cfg3 */
0x5ab8, /* mpllb cfg4 */
0x4c34, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x6000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_dp_hbr1 = {
.clock = 270000,
.tx = { 0xbe88, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x308c, /* mpllb cfg0 */
0x2110, /* mpllb cfg1 */
0xcc9c, /* mpllb cfg2 */
0xbfc1, /* mpllb cfg3 */
0x4b9a, /* mpllb cfg4 */
0x3f81, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x5000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_dp_hbr2 = {
.clock = 540000,
.tx = { 0xbe88, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x108c, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0xcc9c, /* mpllb cfg2 */
0xbfc1, /* mpllb cfg3 */
0x4b9a, /* mpllb cfg4 */
0x3f81, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x5000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_dp_hbr3 = {
.clock = 810000,
.tx = { 0xbe88, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x10d2, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0x8d98, /* mpllb cfg2 */
0xbfc1, /* mpllb cfg3 */
0x7166, /* mpllb cfg4 */
0x5f42, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x7800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
/* C20 basic DP 2.0 tables */
static const struct intel_c20pll_state mtl_c20_dp_uhbr10 = {
.clock = 1000000, /* 10 Gbps */
.tx = { 0xbe21, /* tx cfg0 */
0xe800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0700, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mplla = { 0x3104, /* mplla cfg0 */
0xd105, /* mplla cfg1 */
0xc025, /* mplla cfg2 */
0xc025, /* mplla cfg3 */
0x8c00, /* mplla cfg4 */
0x759a, /* mplla cfg5 */
0x4000, /* mplla cfg6 */
0x0003, /* mplla cfg7 */
0x3555, /* mplla cfg8 */
0x0001, /* mplla cfg9 */
},
};
static const struct intel_c20pll_state mtl_c20_dp_uhbr13_5 = {
.clock = 1350000, /* 13.5 Gbps */
.tx = { 0xbea0, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x015f, /* mpllb cfg0 */
0x2205, /* mpllb cfg1 */
0x1b17, /* mpllb cfg2 */
0xffc1, /* mpllb cfg3 */
0xe100, /* mpllb cfg4 */
0xbd00, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x4800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_dp_uhbr20 = {
.clock = 2000000, /* 20 Gbps */
.tx = { 0xbe20, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mplla = { 0x3104, /* mplla cfg0 */
0xd105, /* mplla cfg1 */
0x9217, /* mplla cfg2 */
0x9217, /* mplla cfg3 */
0x8c00, /* mplla cfg4 */
0x759a, /* mplla cfg5 */
0x4000, /* mplla cfg6 */
0x0003, /* mplla cfg7 */
0x3555, /* mplla cfg8 */
0x0001, /* mplla cfg9 */
},
};
static const struct intel_c20pll_state * const mtl_c20_dp_tables[] = {
&mtl_c20_dp_rbr,
&mtl_c20_dp_hbr1,
&mtl_c20_dp_hbr2,
&mtl_c20_dp_hbr3,
&mtl_c20_dp_uhbr10,
&mtl_c20_dp_uhbr13_5,
&mtl_c20_dp_uhbr20,
NULL,
};
/*
* eDP link rates with 38.4 MHz reference clock.
*/
static const struct intel_c20pll_state xe2hpd_c20_edp_r216 = {
.clock = 216000,
.tx = { 0xbe88,
0x4800,
0x0000,
},
.cmn = { 0x0500,
0x0005,
0x0000,
0x0000,
},
.mpllb = { 0x50e1,
0x2120,
0x8e18,
0xbfc1,
0x9000,
0x78f6,
0x0000,
0x0000,
0x0000,
0x0000,
0x0000,
},
};
static const struct intel_c20pll_state xe2hpd_c20_edp_r243 = {
.clock = 243000,
.tx = { 0xbe88,
0x4800,
0x0000,
},
.cmn = { 0x0500,
0x0005,
0x0000,
0x0000,
},
.mpllb = { 0x50fd,
0x2120,
0x8f18,
0xbfc1,
0xa200,
0x8814,
0x2000,
0x0001,
0x1000,
0x0000,
0x0000,
},
};
static const struct intel_c20pll_state xe2hpd_c20_edp_r324 = {
.clock = 324000,
.tx = { 0xbe88,
0x4800,
0x0000,
},
.cmn = { 0x0500,
0x0005,
0x0000,
0x0000,
},
.mpllb = { 0x30a8,
0x2110,
0xcd9a,
0xbfc1,
0x6c00,
0x5ab8,
0x2000,
0x0001,
0x6000,
0x0000,
0x0000,
},
};
static const struct intel_c20pll_state xe2hpd_c20_edp_r432 = {
.clock = 432000,
.tx = { 0xbe88,
0x4800,
0x0000,
},
.cmn = { 0x0500,
0x0005,
0x0000,
0x0000,
},
.mpllb = { 0x30e1,
0x2110,
0x8e18,
0xbfc1,
0x9000,
0x78f6,
0x0000,
0x0000,
0x0000,
0x0000,
0x0000,
},
};
static const struct intel_c20pll_state xe2hpd_c20_edp_r675 = {
.clock = 675000,
.tx = { 0xbe88,
0x4800,
0x0000,
},
.cmn = { 0x0500,
0x0005,
0x0000,
0x0000,
},
.mpllb = { 0x10af,
0x2108,
0xce1a,
0xbfc1,
0x7080,
0x5e80,
0x2000,
0x0001,
0x6400,
0x0000,
0x0000,
},
};
static const struct intel_c20pll_state * const xe2hpd_c20_edp_tables[] = {
&mtl_c20_dp_rbr,
&xe2hpd_c20_edp_r216,
&xe2hpd_c20_edp_r243,
&mtl_c20_dp_hbr1,
&xe2hpd_c20_edp_r324,
&xe2hpd_c20_edp_r432,
&mtl_c20_dp_hbr2,
&xe2hpd_c20_edp_r675,
&mtl_c20_dp_hbr3,
NULL,
};
static const struct intel_c20pll_state xe2hpd_c20_dp_uhbr13_5 = {
.clock = 1350000, /* 13.5 Gbps */
.tx = { 0xbea0, /* tx cfg0 */
0x4800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = {0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x015f, /* mpllb cfg0 */
0x2205, /* mpllb cfg1 */
0x1b17, /* mpllb cfg2 */
0xffc1, /* mpllb cfg3 */
0xbd00, /* mpllb cfg4 */
0x9ec3, /* mpllb cfg5 */
0x2000, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x4800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0000, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state * const xe2hpd_c20_dp_tables[] = {
&mtl_c20_dp_rbr,
&mtl_c20_dp_hbr1,
&mtl_c20_dp_hbr2,
&mtl_c20_dp_hbr3,
&mtl_c20_dp_uhbr10,
&xe2hpd_c20_dp_uhbr13_5,
NULL,
};
static const struct intel_c20pll_state * const xe3lpd_c20_dp_edp_tables[] = {
&mtl_c20_dp_rbr,
&xe2hpd_c20_edp_r216,
&xe2hpd_c20_edp_r243,
&mtl_c20_dp_hbr1,
&xe2hpd_c20_edp_r324,
&xe2hpd_c20_edp_r432,
&mtl_c20_dp_hbr2,
&xe2hpd_c20_edp_r675,
&mtl_c20_dp_hbr3,
&mtl_c20_dp_uhbr10,
&xe2hpd_c20_dp_uhbr13_5,
&mtl_c20_dp_uhbr20,
NULL,
};
/*
* HDMI link rates with 38.4 MHz reference clock.
*/
static const struct intel_c10pll_state mtl_c10_hdmi_25_2 = {
.clock = 25200,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x4,
.pll[1] = 0,
.pll[2] = 0xB2,
.pll[3] = 0,
.pll[4] = 0,
.pll[5] = 0,
.pll[6] = 0,
.pll[7] = 0,
.pll[8] = 0x20,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0xD,
.pll[16] = 0x6,
.pll[17] = 0x8F,
.pll[18] = 0x84,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_27_0 = {
.clock = 27000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34,
.pll[1] = 0,
.pll[2] = 0xC0,
.pll[3] = 0,
.pll[4] = 0,
.pll[5] = 0,
.pll[6] = 0,
.pll[7] = 0,
.pll[8] = 0x20,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0x80,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0xD,
.pll[16] = 0x6,
.pll[17] = 0xCF,
.pll[18] = 0x84,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_74_25 = {
.clock = 74250,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4,
.pll[1] = 0,
.pll[2] = 0x7A,
.pll[3] = 0,
.pll[4] = 0,
.pll[5] = 0,
.pll[6] = 0,
.pll[7] = 0,
.pll[8] = 0x20,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0x58,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0xB,
.pll[16] = 0x6,
.pll[17] = 0xF,
.pll[18] = 0x85,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_148_5 = {
.clock = 148500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4,
.pll[1] = 0,
.pll[2] = 0x7A,
.pll[3] = 0,
.pll[4] = 0,
.pll[5] = 0,
.pll[6] = 0,
.pll[7] = 0,
.pll[8] = 0x20,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0x58,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0xA,
.pll[16] = 0x6,
.pll[17] = 0xF,
.pll[18] = 0x85,
.pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_594 = {
.clock = 594000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4,
.pll[1] = 0,
.pll[2] = 0x7A,
.pll[3] = 0,
.pll[4] = 0,
.pll[5] = 0,
.pll[6] = 0,
.pll[7] = 0,
.pll[8] = 0x20,
.pll[9] = 0x1,
.pll[10] = 0,
.pll[11] = 0,
.pll[12] = 0x58,
.pll[13] = 0,
.pll[14] = 0,
.pll[15] = 0x8,
.pll[16] = 0x6,
.pll[17] = 0xF,
.pll[18] = 0x85,
.pll[19] = 0x23,
};
/* Precomputed C10 HDMI PLL tables */
static const struct intel_c10pll_state mtl_c10_hdmi_27027 = {
.clock = 27027,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xC0, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xCC, .pll[12] = 0x9C, .pll[13] = 0xCB, .pll[14] = 0xCC,
.pll[15] = 0x0D, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_28320 = {
.clock = 28320,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x04, .pll[1] = 0x00, .pll[2] = 0xCC, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x00, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0D, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_30240 = {
.clock = 30240,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x04, .pll[1] = 0x00, .pll[2] = 0xDC, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x00, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0D, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_31500 = {
.clock = 31500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x62, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0xA0, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0C, .pll[16] = 0x09, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_36000 = {
.clock = 36000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xC4, .pll[1] = 0x00, .pll[2] = 0x76, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x00, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_40000 = {
.clock = 40000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x86, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0x55, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_49500 = {
.clock = 49500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x74, .pll[1] = 0x00, .pll[2] = 0xAE, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x20, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_50000 = {
.clock = 50000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x74, .pll[1] = 0x00, .pll[2] = 0xB0, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0x2A, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_57284 = {
.clock = 57284,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xCE, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x77, .pll[12] = 0x57, .pll[13] = 0x77, .pll[14] = 0x77,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_58000 = {
.clock = 58000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xD0, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0xD5, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0C, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_65000 = {
.clock = 65000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x66, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0xB5, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0B, .pll[16] = 0x09, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_71000 = {
.clock = 71000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x72, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0xF5, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_74176 = {
.clock = 74176,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x44, .pll[12] = 0x44, .pll[13] = 0x44, .pll[14] = 0x44,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_75000 = {
.clock = 75000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7C, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x20, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_78750 = {
.clock = 78750,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x84, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x08, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_85500 = {
.clock = 85500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x92, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x10, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_88750 = {
.clock = 88750,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x74, .pll[1] = 0x00, .pll[2] = 0x98, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0x72, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x0B, .pll[16] = 0x09, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_106500 = {
.clock = 106500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xBC, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0xF0, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_108000 = {
.clock = 108000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xC0, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x80, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_115500 = {
.clock = 115500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xD0, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x50, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_119000 = {
.clock = 119000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xD6, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0xF5, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0B, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_135000 = {
.clock = 135000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x6C, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x50, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0A, .pll[16] = 0x09, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_138500 = {
.clock = 138500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x70, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0x22, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_147160 = {
.clock = 147160,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x78, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0xA5, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_148352 = {
.clock = 148352,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x44, .pll[12] = 0x44, .pll[13] = 0x44, .pll[14] = 0x44,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_154000 = {
.clock = 154000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x80, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0x35, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_162000 = {
.clock = 162000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x88, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x60, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_167000 = {
.clock = 167000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x8C, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0xFA, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_197802 = {
.clock = 197802,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x74, .pll[1] = 0x00, .pll[2] = 0xAE, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x99, .pll[12] = 0x05, .pll[13] = 0x98, .pll[14] = 0x99,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_198000 = {
.clock = 198000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x74, .pll[1] = 0x00, .pll[2] = 0xAE, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x20, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_209800 = {
.clock = 209800,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xBA, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0x45, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_241500 = {
.clock = 241500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xDA, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0xC8, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x0A, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_262750 = {
.clock = 262750,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x68, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0x6C, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x09, .pll[16] = 0x09, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_268500 = {
.clock = 268500,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x6A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0xEC, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x09, .pll[16] = 0x09, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_296703 = {
.clock = 296703,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x33, .pll[12] = 0x44, .pll[13] = 0x33, .pll[14] = 0x33,
.pll[15] = 0x09, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_297000 = {
.clock = 297000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x00, .pll[12] = 0x58, .pll[13] = 0x00, .pll[14] = 0x00,
.pll[15] = 0x09, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_319750 = {
.clock = 319750,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xB4, .pll[1] = 0x00, .pll[2] = 0x86, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0xAA, .pll[12] = 0x44, .pll[13] = 0xA9, .pll[14] = 0xAA,
.pll[15] = 0x09, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_497750 = {
.clock = 497750,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0x34, .pll[1] = 0x00, .pll[2] = 0xE2, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0x9F, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x09, .pll[16] = 0x08, .pll[17] = 0xCF, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_592000 = {
.clock = 592000,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x55, .pll[12] = 0x15, .pll[13] = 0x55, .pll[14] = 0x55,
.pll[15] = 0x08, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state mtl_c10_hdmi_593407 = {
.clock = 593407,
.tx = 0x10,
.cmn = 0x1,
.pll[0] = 0xF4, .pll[1] = 0x00, .pll[2] = 0x7A, .pll[3] = 0x00, .pll[4] = 0x00,
.pll[5] = 0x00, .pll[6] = 0x00, .pll[7] = 0x00, .pll[8] = 0x20, .pll[9] = 0xFF,
.pll[10] = 0xFF, .pll[11] = 0x3B, .pll[12] = 0x44, .pll[13] = 0xBA, .pll[14] = 0xBB,
.pll[15] = 0x08, .pll[16] = 0x08, .pll[17] = 0x8F, .pll[18] = 0x84, .pll[19] = 0x23,
};
static const struct intel_c10pll_state * const mtl_c10_hdmi_tables[] = {
&mtl_c10_hdmi_25_2, /* Consolidated Table */
&mtl_c10_hdmi_27_0, /* Consolidated Table */
&mtl_c10_hdmi_27027,
&mtl_c10_hdmi_28320,
&mtl_c10_hdmi_30240,
&mtl_c10_hdmi_31500,
&mtl_c10_hdmi_36000,
&mtl_c10_hdmi_40000,
&mtl_c10_hdmi_49500,
&mtl_c10_hdmi_50000,
&mtl_c10_hdmi_57284,
&mtl_c10_hdmi_58000,
&mtl_c10_hdmi_65000,
&mtl_c10_hdmi_71000,
&mtl_c10_hdmi_74176,
&mtl_c10_hdmi_74_25, /* Consolidated Table */
&mtl_c10_hdmi_75000,
&mtl_c10_hdmi_78750,
&mtl_c10_hdmi_85500,
&mtl_c10_hdmi_88750,
&mtl_c10_hdmi_106500,
&mtl_c10_hdmi_108000,
&mtl_c10_hdmi_115500,
&mtl_c10_hdmi_119000,
&mtl_c10_hdmi_135000,
&mtl_c10_hdmi_138500,
&mtl_c10_hdmi_147160,
&mtl_c10_hdmi_148352,
&mtl_c10_hdmi_148_5, /* Consolidated Table */
&mtl_c10_hdmi_154000,
&mtl_c10_hdmi_162000,
&mtl_c10_hdmi_167000,
&mtl_c10_hdmi_197802,
&mtl_c10_hdmi_198000,
&mtl_c10_hdmi_209800,
&mtl_c10_hdmi_241500,
&mtl_c10_hdmi_262750,
&mtl_c10_hdmi_268500,
&mtl_c10_hdmi_296703,
&mtl_c10_hdmi_297000,
&mtl_c10_hdmi_319750,
&mtl_c10_hdmi_497750,
&mtl_c10_hdmi_592000,
&mtl_c10_hdmi_593407,
&mtl_c10_hdmi_594, /* Consolidated Table */
NULL,
};
static const struct intel_c20pll_state mtl_c20_hdmi_25_175 = {
.clock = 25175,
.tx = { 0xbe88, /* tx cfg0 */
0x9800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0xa0d2, /* mpllb cfg0 */
0x7d80, /* mpllb cfg1 */
0x0906, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x0200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x0000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0001, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_27_0 = {
.clock = 27000,
.tx = { 0xbe88, /* tx cfg0 */
0x9800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0xa0e0, /* mpllb cfg0 */
0x7d80, /* mpllb cfg1 */
0x0906, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x8000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0001, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_74_25 = {
.clock = 74250,
.tx = { 0xbe88, /* tx cfg0 */
0x9800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x609a, /* mpllb cfg0 */
0x7d40, /* mpllb cfg1 */
0xca06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x5800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0001, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_148_5 = {
.clock = 148500,
.tx = { 0xbe88, /* tx cfg0 */
0x9800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x409a, /* mpllb cfg0 */
0x7d20, /* mpllb cfg1 */
0xca06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x5800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0001, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_594 = {
.clock = 594000,
.tx = { 0xbe88, /* tx cfg0 */
0x9800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x009a, /* mpllb cfg0 */
0x7d08, /* mpllb cfg1 */
0xca06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x5800, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0001, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_300 = {
.clock = 3000000,
.tx = { 0xbe98, /* tx cfg0 */
0x8800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x309c, /* mpllb cfg0 */
0x2110, /* mpllb cfg1 */
0xca06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x2000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0004, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_600 = {
.clock = 6000000,
.tx = { 0xbe98, /* tx cfg0 */
0x8800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x109c, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0xca06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x2000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0004, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_800 = {
.clock = 8000000,
.tx = { 0xbe98, /* tx cfg0 */
0x8800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x10d0, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0x4a06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0003, /* mpllb cfg7 */
0x2aaa, /* mpllb cfg8 */
0x0002, /* mpllb cfg9 */
0x0004, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_1000 = {
.clock = 10000000,
.tx = { 0xbe98, /* tx cfg0 */
0x8800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x1104, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0x0a06, /* mpllb cfg2 */
0xbe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0003, /* mpllb cfg7 */
0x3555, /* mpllb cfg8 */
0x0001, /* mpllb cfg9 */
0x0004, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state mtl_c20_hdmi_1200 = {
.clock = 12000000,
.tx = { 0xbe98, /* tx cfg0 */
0x8800, /* tx cfg1 */
0x0000, /* tx cfg2 */
},
.cmn = { 0x0500, /* cmn cfg0*/
0x0005, /* cmn cfg1 */
0x0000, /* cmn cfg2 */
0x0000, /* cmn cfg3 */
},
.mpllb = { 0x1138, /* mpllb cfg0 */
0x2108, /* mpllb cfg1 */
0x5486, /* mpllb cfg2 */
0xfe40, /* mpllb cfg3 */
0x0000, /* mpllb cfg4 */
0x0000, /* mpllb cfg5 */
0x2200, /* mpllb cfg6 */
0x0001, /* mpllb cfg7 */
0x4000, /* mpllb cfg8 */
0x0000, /* mpllb cfg9 */
0x0004, /* mpllb cfg10 */
},
};
static const struct intel_c20pll_state * const mtl_c20_hdmi_tables[] = {
&mtl_c20_hdmi_25_175,
&mtl_c20_hdmi_27_0,
&mtl_c20_hdmi_74_25,
&mtl_c20_hdmi_148_5,
&mtl_c20_hdmi_594,
&mtl_c20_hdmi_300,
&mtl_c20_hdmi_600,
&mtl_c20_hdmi_800,
&mtl_c20_hdmi_1000,
&mtl_c20_hdmi_1200,
NULL,
};
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
static const struct intel_c10pll_state * const *
intel_c10pll_tables_get(struct intel_crtc_state *crtc_state,
struct intel_encoder *encoder)
{
if (intel_crtc_has_dp_encoder(crtc_state)) {
if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_EDP))
return mtl_c10_edp_tables;
else
return mtl_c10_dp_tables;
} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI)) {
return mtl_c10_hdmi_tables;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
MISSING_CASE(encoder->type);
return NULL;
}
static void intel_cx0pll_update_ssc(struct intel_encoder *encoder,
struct intel_cx0pll_state *pll_state, bool is_dp)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (is_dp) {
if (intel_panel_use_ssc(display)) {
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
pll_state->ssc_enabled =
(intel_dp->dpcd[DP_MAX_DOWNSPREAD] & DP_MAX_DOWNSPREAD_0_5);
}
}
}
static void intel_c10pll_update_pll(struct intel_encoder *encoder,
struct intel_cx0pll_state *pll_state)
{
struct intel_display *display = to_intel_display(encoder);
int i;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (pll_state->ssc_enabled)
return;
drm_WARN_ON(display->drm, ARRAY_SIZE(pll_state->c10.pll) < 9);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
for (i = 4; i < 9; i++)
pll_state->c10.pll[i] = 0;
}
static int intel_c10pll_calc_state_from_table(struct intel_encoder *encoder,
const struct intel_c10pll_state * const *tables,
bool is_dp, int port_clock,
struct intel_cx0pll_state *pll_state)
{
int i;
for (i = 0; tables[i]; i++) {
if (port_clock == tables[i]->clock) {
pll_state->c10 = *tables[i];
intel_cx0pll_update_ssc(encoder, pll_state, is_dp);
intel_c10pll_update_pll(encoder, pll_state);
pll_state->use_c10 = true;
return 0;
}
}
return -EINVAL;
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
static int intel_c10pll_calc_state(struct intel_crtc_state *crtc_state,
struct intel_encoder *encoder)
{
const struct intel_c10pll_state * const *tables;
int err;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
tables = intel_c10pll_tables_get(crtc_state, encoder);
if (!tables)
return -EINVAL;
err = intel_c10pll_calc_state_from_table(encoder, tables,
intel_crtc_has_dp_encoder(crtc_state),
crtc_state->port_clock,
&crtc_state->dpll_hw_state.cx0pll);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (err == 0 || !intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI))
return err;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* For HDMI PLLs try SNPS PHY algorithm, if there are no precomputed tables */
intel_snps_hdmi_pll_compute_c10pll(&crtc_state->dpll_hw_state.cx0pll.c10,
crtc_state->port_clock);
intel_c10pll_update_pll(encoder,
&crtc_state->dpll_hw_state.cx0pll);
crtc_state->dpll_hw_state.cx0pll.use_c10 = true;
return 0;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_c10pll_readout_hw_state(struct intel_encoder *encoder,
struct intel_c10pll_state *pll_state)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
u8 lane = INTEL_CX0_LANE0;
intel_wakeref_t wakeref;
int i;
wakeref = intel_cx0_phy_transaction_begin(encoder);
/*
* According to C10 VDR Register programming Sequence we need
* to do this to read PHY internal registers from MsgBus.
*/
intel_cx0_rmw(encoder, lane, PHY_C10_VDR_CONTROL(1),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
0, C10_VDR_CTRL_MSGBUS_ACCESS,
MB_WRITE_COMMITTED);
for (i = 0; i < ARRAY_SIZE(pll_state->pll); i++)
pll_state->pll[i] = intel_cx0_read(encoder, lane, PHY_C10_VDR_PLL(i));
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
pll_state->cmn = intel_cx0_read(encoder, lane, PHY_C10_VDR_CMN(0));
pll_state->tx = intel_cx0_read(encoder, lane, PHY_C10_VDR_TX(0));
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_phy_transaction_end(encoder, wakeref);
}
static void intel_c10_pll_program(struct intel_display *display,
struct intel_encoder *encoder,
const struct intel_c10pll_state *pll_state)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
int i;
intel_cx0_rmw(encoder, INTEL_CX0_BOTH_LANES, PHY_C10_VDR_CONTROL(1),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
0, C10_VDR_CTRL_MSGBUS_ACCESS,
MB_WRITE_COMMITTED);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* Program the pll values only for the master lane */
for (i = 0; i < ARRAY_SIZE(pll_state->pll); i++)
intel_cx0_write(encoder, INTEL_CX0_LANE0, PHY_C10_VDR_PLL(i),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
pll_state->pll[i],
(i % 4) ? MB_WRITE_UNCOMMITTED : MB_WRITE_COMMITTED);
intel_cx0_write(encoder, INTEL_CX0_LANE0, PHY_C10_VDR_CMN(0), pll_state->cmn, MB_WRITE_COMMITTED);
intel_cx0_write(encoder, INTEL_CX0_LANE0, PHY_C10_VDR_TX(0), pll_state->tx, MB_WRITE_COMMITTED);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* Custom width needs to be programmed to 0 for both the phy lanes */
intel_cx0_rmw(encoder, INTEL_CX0_BOTH_LANES, PHY_C10_VDR_CUSTOM_WIDTH,
C10_VDR_CUSTOM_WIDTH_MASK, C10_VDR_CUSTOM_WIDTH_8_10,
MB_WRITE_COMMITTED);
intel_cx0_rmw(encoder, INTEL_CX0_LANE0, PHY_C10_VDR_CONTROL(1),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
0, C10_VDR_CTRL_MASTER_LANE | C10_VDR_CTRL_UPDATE_CFG,
MB_WRITE_COMMITTED);
}
static void intel_c10pll_dump_hw_state(struct intel_display *display,
const struct intel_c10pll_state *hw_state)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
bool fracen;
int i;
unsigned int frac_quot = 0, frac_rem = 0, frac_den = 1;
unsigned int multiplier, tx_clk_div;
fracen = hw_state->pll[0] & C10_PLL0_FRACEN;
drm_dbg_kms(display->drm, "c10pll_hw_state: fracen: %s, ",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
str_yes_no(fracen));
if (fracen) {
frac_quot = hw_state->pll[12] << 8 | hw_state->pll[11];
frac_rem = hw_state->pll[14] << 8 | hw_state->pll[13];
frac_den = hw_state->pll[10] << 8 | hw_state->pll[9];
drm_dbg_kms(display->drm, "quot: %u, rem: %u, den: %u,\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
frac_quot, frac_rem, frac_den);
}
multiplier = (REG_FIELD_GET8(C10_PLL3_MULTIPLIERH_MASK, hw_state->pll[3]) << 8 |
hw_state->pll[2]) / 2 + 16;
tx_clk_div = REG_FIELD_GET8(C10_PLL15_TXCLKDIV_MASK, hw_state->pll[15]);
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"multiplier: %u, tx_clk_div: %u.\n", multiplier, tx_clk_div);
drm_dbg_kms(display->drm, "c10pll_rawhw_state:");
drm_dbg_kms(display->drm, "tx: 0x%x, cmn: 0x%x\n", hw_state->tx,
hw_state->cmn);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
BUILD_BUG_ON(ARRAY_SIZE(hw_state->pll) % 4);
for (i = 0; i < ARRAY_SIZE(hw_state->pll); i = i + 4)
drm_dbg_kms(display->drm,
"pll[%d] = 0x%x, pll[%d] = 0x%x, pll[%d] = 0x%x, pll[%d] = 0x%x\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
i, hw_state->pll[i], i + 1, hw_state->pll[i + 1],
i + 2, hw_state->pll[i + 2], i + 3, hw_state->pll[i + 3]);
}
/*
* Some ARLs SoCs have the same drm PCI IDs, so need a helper to differentiate based
* on the host bridge device ID to get the correct txx_mics value.
*/
static bool is_arrowlake_s_by_host_bridge(void)
{
struct pci_dev *pdev = NULL;
u16 host_bridge_pci_dev_id;
while ((pdev = pci_get_class(PCI_CLASS_BRIDGE_HOST << 8, pdev)))
host_bridge_pci_dev_id = pdev->device;
return pdev && IS_ARROWLAKE_S_BY_HOST_BRIDGE_ID(host_bridge_pci_dev_id);
}
static u16 intel_c20_hdmi_tmds_tx_cgf_1(struct intel_crtc_state *crtc_state)
{
struct intel_display *display = to_intel_display(crtc_state);
u16 tx_misc;
u16 tx_dcc_cal_dac_ctrl_range = 8;
u16 tx_term_ctrl = 2;
if (DISPLAY_VER(display) >= 20) {
tx_misc = 5;
tx_term_ctrl = 4;
} else if (display->platform.battlemage) {
tx_misc = 0;
} else if (display->platform.meteorlake_u ||
is_arrowlake_s_by_host_bridge()) {
tx_misc = 3;
} else {
tx_misc = 7;
}
return (C20_PHY_TX_MISC(tx_misc) |
C20_PHY_TX_DCC_CAL_RANGE(tx_dcc_cal_dac_ctrl_range) |
C20_PHY_TX_DCC_BYPASS | C20_PHY_TX_TERM_CTL(tx_term_ctrl));
}
static int intel_c20_compute_hdmi_tmds_pll(struct intel_crtc_state *crtc_state)
{
struct intel_c20pll_state *pll_state = &crtc_state->dpll_hw_state.cx0pll.c20;
u64 datarate;
u64 mpll_tx_clk_div;
u64 vco_freq_shift;
u64 vco_freq;
u64 multiplier;
u64 mpll_multiplier;
u64 mpll_fracn_quot;
u64 mpll_fracn_rem;
u8 mpllb_ana_freq_vco;
u8 mpll_div_multiplier;
if (crtc_state->port_clock < 25175 || crtc_state->port_clock > 600000)
return -EINVAL;
datarate = ((u64)crtc_state->port_clock * 1000) * 10;
mpll_tx_clk_div = ilog2(div64_u64((u64)CLOCK_9999MHZ, (u64)datarate));
vco_freq_shift = ilog2(div64_u64((u64)CLOCK_4999MHZ * (u64)256, (u64)datarate));
vco_freq = (datarate << vco_freq_shift) >> 8;
multiplier = div64_u64((vco_freq << 28), (REFCLK_38_4_MHZ >> 4));
mpll_multiplier = 2 * (multiplier >> 32);
mpll_fracn_quot = (multiplier >> 16) & 0xFFFF;
mpll_fracn_rem = multiplier & 0xFFFF;
mpll_div_multiplier = min_t(u8, div64_u64((vco_freq * 16 + (datarate >> 1)),
datarate), 255);
if (vco_freq <= DATARATE_3000000000)
mpllb_ana_freq_vco = MPLLB_ANA_FREQ_VCO_3;
else if (vco_freq <= DATARATE_3500000000)
mpllb_ana_freq_vco = MPLLB_ANA_FREQ_VCO_2;
else if (vco_freq <= DATARATE_4000000000)
mpllb_ana_freq_vco = MPLLB_ANA_FREQ_VCO_1;
else
mpllb_ana_freq_vco = MPLLB_ANA_FREQ_VCO_0;
pll_state->clock = crtc_state->port_clock;
pll_state->tx[0] = 0xbe88;
pll_state->tx[1] = intel_c20_hdmi_tmds_tx_cgf_1(crtc_state);
pll_state->tx[2] = 0x0000;
pll_state->cmn[0] = 0x0500;
pll_state->cmn[1] = 0x0005;
pll_state->cmn[2] = 0x0000;
pll_state->cmn[3] = 0x0000;
pll_state->mpllb[0] = (MPLL_TX_CLK_DIV(mpll_tx_clk_div) |
MPLL_MULTIPLIER(mpll_multiplier));
pll_state->mpllb[1] = (CAL_DAC_CODE(CAL_DAC_CODE_31) |
WORD_CLK_DIV |
MPLL_DIV_MULTIPLIER(mpll_div_multiplier));
pll_state->mpllb[2] = (MPLLB_ANA_FREQ_VCO(mpllb_ana_freq_vco) |
CP_PROP(CP_PROP_20) |
CP_INT(CP_INT_6));
pll_state->mpllb[3] = (V2I(V2I_2) |
CP_PROP_GS(CP_PROP_GS_30) |
CP_INT_GS(CP_INT_GS_28));
pll_state->mpllb[4] = 0x0000;
pll_state->mpllb[5] = 0x0000;
pll_state->mpllb[6] = (C20_MPLLB_FRACEN | SSC_UP_SPREAD);
pll_state->mpllb[7] = MPLL_FRACN_DEN;
pll_state->mpllb[8] = mpll_fracn_quot;
pll_state->mpllb[9] = mpll_fracn_rem;
pll_state->mpllb[10] = HDMI_DIV(HDMI_DIV_1);
return 0;
}
static const struct intel_c20pll_state * const *
intel_c20_pll_tables_get(struct intel_crtc_state *crtc_state,
struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(crtc_state);
if (intel_crtc_has_dp_encoder(crtc_state)) {
if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_EDP)) {
if (DISPLAY_RUNTIME_INFO(display)->edp_typec_support)
return xe3lpd_c20_dp_edp_tables;
if (DISPLAY_VERx100(display) == 1401)
return xe2hpd_c20_edp_tables;
}
if (DISPLAY_VER(display) >= 30)
return xe3lpd_c20_dp_edp_tables;
else if (DISPLAY_VERx100(display) == 1401)
return xe2hpd_c20_dp_tables;
else
return mtl_c20_dp_tables;
} else if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI)) {
return mtl_c20_hdmi_tables;
}
MISSING_CASE(encoder->type);
return NULL;
}
static int intel_c20pll_calc_state(struct intel_crtc_state *crtc_state,
struct intel_encoder *encoder)
{
const struct intel_c20pll_state * const *tables;
int i;
/* try computed C20 HDMI tables before using consolidated tables */
if (intel_crtc_has_type(crtc_state, INTEL_OUTPUT_HDMI)) {
if (intel_c20_compute_hdmi_tmds_pll(crtc_state) == 0)
return 0;
}
tables = intel_c20_pll_tables_get(crtc_state, encoder);
if (!tables)
return -EINVAL;
for (i = 0; tables[i]; i++) {
if (crtc_state->port_clock == tables[i]->clock) {
crtc_state->dpll_hw_state.cx0pll.c20 = *tables[i];
intel_cx0pll_update_ssc(encoder,
&crtc_state->dpll_hw_state.cx0pll,
intel_crtc_has_dp_encoder(crtc_state));
crtc_state->dpll_hw_state.cx0pll.use_c10 = false;
return 0;
}
}
return -EINVAL;
}
int intel_cx0pll_calc_state(struct intel_crtc_state *crtc_state,
struct intel_encoder *encoder)
{
if (intel_encoder_is_c10phy(encoder))
return intel_c10pll_calc_state(crtc_state, encoder);
return intel_c20pll_calc_state(crtc_state, encoder);
}
static bool intel_c20phy_use_mpllb(const struct intel_c20pll_state *state)
{
return state->tx[0] & C20_PHY_USE_MPLLB;
}
static int intel_c20pll_calc_port_clock(struct intel_encoder *encoder,
const struct intel_c20pll_state *pll_state)
{
unsigned int frac, frac_en, frac_quot, frac_rem, frac_den;
unsigned int multiplier, refclk = 38400;
unsigned int tx_clk_div;
unsigned int ref_clk_mpllb_div;
unsigned int fb_clk_div4_en;
unsigned int ref, vco;
unsigned int tx_rate_mult;
unsigned int tx_rate = REG_FIELD_GET(C20_PHY_TX_RATE, pll_state->tx[0]);
if (intel_c20phy_use_mpllb(pll_state)) {
tx_rate_mult = 1;
frac_en = REG_FIELD_GET(C20_MPLLB_FRACEN, pll_state->mpllb[6]);
frac_quot = pll_state->mpllb[8];
frac_rem = pll_state->mpllb[9];
frac_den = pll_state->mpllb[7];
multiplier = REG_FIELD_GET(C20_MULTIPLIER_MASK, pll_state->mpllb[0]);
tx_clk_div = REG_FIELD_GET(C20_MPLLB_TX_CLK_DIV_MASK, pll_state->mpllb[0]);
ref_clk_mpllb_div = REG_FIELD_GET(C20_REF_CLK_MPLLB_DIV_MASK, pll_state->mpllb[6]);
fb_clk_div4_en = 0;
} else {
tx_rate_mult = 2;
frac_en = REG_FIELD_GET(C20_MPLLA_FRACEN, pll_state->mplla[6]);
frac_quot = pll_state->mplla[8];
frac_rem = pll_state->mplla[9];
frac_den = pll_state->mplla[7];
multiplier = REG_FIELD_GET(C20_MULTIPLIER_MASK, pll_state->mplla[0]);
tx_clk_div = REG_FIELD_GET(C20_MPLLA_TX_CLK_DIV_MASK, pll_state->mplla[1]);
ref_clk_mpllb_div = REG_FIELD_GET(C20_REF_CLK_MPLLB_DIV_MASK, pll_state->mplla[6]);
fb_clk_div4_en = REG_FIELD_GET(C20_FB_CLK_DIV4_EN, pll_state->mplla[0]);
}
if (frac_en)
frac = frac_quot + DIV_ROUND_CLOSEST(frac_rem, frac_den);
else
frac = 0;
ref = DIV_ROUND_CLOSEST(refclk * (1 << (1 + fb_clk_div4_en)), 1 << ref_clk_mpllb_div);
vco = DIV_ROUND_CLOSEST_ULL(mul_u32_u32(ref, (multiplier << (17 - 2)) + frac) >> 17, 10);
return vco << tx_rate_mult >> tx_clk_div >> tx_rate;
}
static void intel_c20pll_readout_hw_state(struct intel_encoder *encoder,
struct intel_c20pll_state *pll_state)
{
struct intel_display *display = to_intel_display(encoder);
bool cntx;
intel_wakeref_t wakeref;
int i;
wakeref = intel_cx0_phy_transaction_begin(encoder);
/* 1. Read current context selection */
cntx = intel_cx0_read(encoder, INTEL_CX0_LANE0, PHY_C20_VDR_CUSTOM_SERDES_RATE) & PHY_C20_CONTEXT_TOGGLE;
/* Read Tx configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->tx); i++) {
if (cntx)
pll_state->tx[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_B_TX_CNTX_CFG(display, i));
else
pll_state->tx[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_A_TX_CNTX_CFG(display, i));
}
/* Read common configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->cmn); i++) {
if (cntx)
pll_state->cmn[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_B_CMN_CNTX_CFG(display, i));
else
pll_state->cmn[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_A_CMN_CNTX_CFG(display, i));
}
if (intel_c20phy_use_mpllb(pll_state)) {
/* MPLLB configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->mpllb); i++) {
if (cntx)
pll_state->mpllb[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_B_MPLLB_CNTX_CFG(display, i));
else
pll_state->mpllb[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_A_MPLLB_CNTX_CFG(display, i));
}
} else {
/* MPLLA configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->mplla); i++) {
if (cntx)
pll_state->mplla[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_B_MPLLA_CNTX_CFG(display, i));
else
pll_state->mplla[i] = intel_c20_sram_read(encoder,
INTEL_CX0_LANE0,
PHY_C20_A_MPLLA_CNTX_CFG(display, i));
}
}
pll_state->clock = intel_c20pll_calc_port_clock(encoder, pll_state);
intel_cx0_phy_transaction_end(encoder, wakeref);
}
static void intel_c20pll_dump_hw_state(struct intel_display *display,
const struct intel_c20pll_state *hw_state)
{
int i;
drm_dbg_kms(display->drm, "c20pll_hw_state:\n");
drm_dbg_kms(display->drm,
"tx[0] = 0x%.4x, tx[1] = 0x%.4x, tx[2] = 0x%.4x\n",
hw_state->tx[0], hw_state->tx[1], hw_state->tx[2]);
drm_dbg_kms(display->drm,
"cmn[0] = 0x%.4x, cmn[1] = 0x%.4x, cmn[2] = 0x%.4x, cmn[3] = 0x%.4x\n",
hw_state->cmn[0], hw_state->cmn[1], hw_state->cmn[2], hw_state->cmn[3]);
if (intel_c20phy_use_mpllb(hw_state)) {
for (i = 0; i < ARRAY_SIZE(hw_state->mpllb); i++)
drm_dbg_kms(display->drm, "mpllb[%d] = 0x%.4x\n", i,
hw_state->mpllb[i]);
} else {
for (i = 0; i < ARRAY_SIZE(hw_state->mplla); i++)
drm_dbg_kms(display->drm, "mplla[%d] = 0x%.4x\n", i,
hw_state->mplla[i]);
}
}
void intel_cx0pll_dump_hw_state(struct intel_display *display,
const struct intel_cx0pll_state *hw_state)
{
if (hw_state->use_c10)
intel_c10pll_dump_hw_state(display, &hw_state->c10);
else
intel_c20pll_dump_hw_state(display, &hw_state->c20);
}
static u8 intel_c20_get_dp_rate(u32 clock)
{
switch (clock) {
case 162000: /* 1.62 Gbps DP1.4 */
return 0;
case 270000: /* 2.7 Gbps DP1.4 */
return 1;
case 540000: /* 5.4 Gbps DP 1.4 */
return 2;
case 810000: /* 8.1 Gbps DP1.4 */
return 3;
case 216000: /* 2.16 Gbps eDP */
return 4;
case 243000: /* 2.43 Gbps eDP */
return 5;
case 324000: /* 3.24 Gbps eDP */
return 6;
case 432000: /* 4.32 Gbps eDP */
return 7;
case 1000000: /* 10 Gbps DP2.0 */
return 8;
case 1350000: /* 13.5 Gbps DP2.0 */
return 9;
case 2000000: /* 20 Gbps DP2.0 */
return 10;
case 648000: /* 6.48 Gbps eDP*/
return 11;
case 675000: /* 6.75 Gbps eDP*/
return 12;
default:
MISSING_CASE(clock);
return 0;
}
}
static u8 intel_c20_get_hdmi_rate(u32 clock)
{
if (clock >= 25175 && clock <= 600000)
return 0;
switch (clock) {
case 300000: /* 3 Gbps */
case 600000: /* 6 Gbps */
case 1200000: /* 12 Gbps */
return 1;
case 800000: /* 8 Gbps */
return 2;
case 1000000: /* 10 Gbps */
return 3;
default:
MISSING_CASE(clock);
return 0;
}
}
static bool is_dp2(u32 clock)
{
/* DP2.0 clock rates */
if (clock == 1000000 || clock == 1350000 || clock == 2000000)
return true;
return false;
}
static bool is_hdmi_frl(u32 clock)
{
switch (clock) {
case 300000: /* 3 Gbps */
case 600000: /* 6 Gbps */
case 800000: /* 8 Gbps */
case 1000000: /* 10 Gbps */
case 1200000: /* 12 Gbps */
return true;
default:
return false;
}
}
static bool intel_c20_protocol_switch_valid(struct intel_encoder *encoder)
{
struct intel_digital_port *intel_dig_port = enc_to_dig_port(encoder);
/* banks should not be cleared for DPALT/USB4/TBT modes */
/* TODO: optimize re-calibration in legacy mode */
return intel_tc_port_in_legacy_mode(intel_dig_port);
}
static int intel_get_c20_custom_width(u32 clock, bool dp)
{
if (dp && is_dp2(clock))
return 2;
else if (is_hdmi_frl(clock))
return 1;
else
return 0;
}
static void intel_c20_pll_program(struct intel_display *display,
struct intel_encoder *encoder,
const struct intel_c20pll_state *pll_state,
bool is_dp, int port_clock)
{
u8 owned_lane_mask = intel_cx0_get_owned_lane_mask(encoder);
bool cntx;
int i;
/* 1. Read current context selection */
cntx = intel_cx0_read(encoder, INTEL_CX0_LANE0, PHY_C20_VDR_CUSTOM_SERDES_RATE) & BIT(0);
/*
* 2. If there is a protocol switch from HDMI to DP or vice versa, clear
* the lane #0 MPLLB CAL_DONE_BANK DP2.0 10G and 20G rates enable MPLLA.
* Protocol switch is only applicable for MPLLA
*/
if (intel_c20_protocol_switch_valid(encoder)) {
for (i = 0; i < 4; i++)
intel_c20_sram_write(encoder, INTEL_CX0_LANE0, RAWLANEAONX_DIG_TX_MPLLB_CAL_DONE_BANK(i), 0);
usleep_range(4000, 4100);
}
/* 3. Write SRAM configuration context. If A in use, write configuration to B context */
/* 3.1 Tx configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->tx); i++) {
if (cntx)
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_A_TX_CNTX_CFG(display, i),
pll_state->tx[i]);
else
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_B_TX_CNTX_CFG(display, i),
pll_state->tx[i]);
}
/* 3.2 common configuration */
for (i = 0; i < ARRAY_SIZE(pll_state->cmn); i++) {
if (cntx)
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_A_CMN_CNTX_CFG(display, i),
pll_state->cmn[i]);
else
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_B_CMN_CNTX_CFG(display, i),
pll_state->cmn[i]);
}
/* 3.3 mpllb or mplla configuration */
if (intel_c20phy_use_mpllb(pll_state)) {
for (i = 0; i < ARRAY_SIZE(pll_state->mpllb); i++) {
if (cntx)
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_A_MPLLB_CNTX_CFG(display, i),
pll_state->mpllb[i]);
else
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_B_MPLLB_CNTX_CFG(display, i),
pll_state->mpllb[i]);
}
} else {
for (i = 0; i < ARRAY_SIZE(pll_state->mplla); i++) {
if (cntx)
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_A_MPLLA_CNTX_CFG(display, i),
pll_state->mplla[i]);
else
intel_c20_sram_write(encoder, INTEL_CX0_LANE0,
PHY_C20_B_MPLLA_CNTX_CFG(display, i),
pll_state->mplla[i]);
}
}
/* 4. Program custom width to match the link protocol */
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C20_VDR_CUSTOM_WIDTH,
PHY_C20_CUSTOM_WIDTH_MASK,
PHY_C20_CUSTOM_WIDTH(intel_get_c20_custom_width(port_clock, is_dp)),
MB_WRITE_COMMITTED);
/* 5. For DP or 6. For HDMI */
if (is_dp) {
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C20_VDR_CUSTOM_SERDES_RATE,
BIT(6) | PHY_C20_CUSTOM_SERDES_MASK,
BIT(6) | PHY_C20_CUSTOM_SERDES(intel_c20_get_dp_rate(port_clock)),
MB_WRITE_COMMITTED);
} else {
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C20_VDR_CUSTOM_SERDES_RATE,
BIT(7) | PHY_C20_CUSTOM_SERDES_MASK,
is_hdmi_frl(port_clock) ? BIT(7) : 0,
MB_WRITE_COMMITTED);
intel_cx0_write(encoder, INTEL_CX0_BOTH_LANES, PHY_C20_VDR_HDMI_RATE,
intel_c20_get_hdmi_rate(port_clock),
MB_WRITE_COMMITTED);
}
/*
* 7. Write Vendor specific registers to toggle context setting to load
* the updated programming toggle context bit
*/
intel_cx0_rmw(encoder, owned_lane_mask, PHY_C20_VDR_CUSTOM_SERDES_RATE,
BIT(0), cntx ? 0 : 1, MB_WRITE_COMMITTED);
}
static int intel_c10pll_calc_port_clock(struct intel_encoder *encoder,
const struct intel_c10pll_state *pll_state)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
unsigned int frac_quot = 0, frac_rem = 0, frac_den = 1;
unsigned int multiplier, tx_clk_div, hdmi_div, refclk = 38400;
int tmpclk = 0;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (pll_state->pll[0] & C10_PLL0_FRACEN) {
frac_quot = pll_state->pll[12] << 8 | pll_state->pll[11];
frac_rem = pll_state->pll[14] << 8 | pll_state->pll[13];
frac_den = pll_state->pll[10] << 8 | pll_state->pll[9];
}
multiplier = (REG_FIELD_GET8(C10_PLL3_MULTIPLIERH_MASK, pll_state->pll[3]) << 8 |
pll_state->pll[2]) / 2 + 16;
tx_clk_div = REG_FIELD_GET8(C10_PLL15_TXCLKDIV_MASK, pll_state->pll[15]);
hdmi_div = REG_FIELD_GET8(C10_PLL15_HDMIDIV_MASK, pll_state->pll[15]);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
tmpclk = DIV_ROUND_CLOSEST_ULL(mul_u32_u32(refclk, (multiplier << 16) + frac_quot) +
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
DIV_ROUND_CLOSEST(refclk * frac_rem, frac_den),
10 << (tx_clk_div + 16));
tmpclk *= (hdmi_div ? 2 : 1);
return tmpclk;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static void intel_program_port_clock_ctl(struct intel_encoder *encoder,
const struct intel_cx0pll_state *pll_state,
bool is_dp, int port_clock,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
bool lane_reversal)
{
struct intel_display *display = to_intel_display(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u32 val = 0;
intel_de_rmw(display, XELPDP_PORT_BUF_CTL1(display, encoder->port),
XELPDP_PORT_REVERSAL,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
lane_reversal ? XELPDP_PORT_REVERSAL : 0);
if (lane_reversal)
val |= XELPDP_LANE1_PHY_CLOCK_SELECT;
val |= XELPDP_FORWARD_CLOCK_UNGATE;
if (!is_dp && is_hdmi_frl(port_clock))
val |= XELPDP_DDI_CLOCK_SELECT_PREP(display, XELPDP_DDI_CLOCK_SELECT_DIV18CLK);
else
val |= XELPDP_DDI_CLOCK_SELECT_PREP(display, XELPDP_DDI_CLOCK_SELECT_MAXPCLK);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* TODO: HDMI FRL */
/* DP2.0 10G and 20G rates enable MPLLA*/
if (port_clock == 1000000 || port_clock == 2000000)
val |= pll_state->ssc_enabled ? XELPDP_SSC_ENABLE_PLLA : 0;
else
val |= pll_state->ssc_enabled ? XELPDP_SSC_ENABLE_PLLB : 0;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_LANE1_PHY_CLOCK_SELECT | XELPDP_FORWARD_CLOCK_UNGATE |
XELPDP_DDI_CLOCK_SELECT_MASK(display) | XELPDP_SSC_ENABLE_PLLA |
XELPDP_SSC_ENABLE_PLLB, val);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static u32 intel_cx0_get_powerdown_update(u8 lane_mask)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_POWERDOWN_UPDATE(lane);
return val;
}
static u32 intel_cx0_get_powerdown_state(u8 lane_mask, u8 state)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_POWERDOWN_NEW_STATE(lane, state);
return val;
}
static void intel_cx0_powerdown_change_sequence(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u8 lane_mask, u8 state)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
i915_reg_t buf_ctl2_reg = XELPDP_PORT_BUF_CTL2(display, port);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int lane;
intel_de_rmw(display, buf_ctl2_reg,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_get_powerdown_state(INTEL_CX0_BOTH_LANES, XELPDP_LANE_POWERDOWN_NEW_STATE_MASK),
intel_cx0_get_powerdown_state(lane_mask, state));
/* Wait for pending transactions.*/
for_each_cx0_lane_in_mask(lane_mask, lane)
if (intel_de_wait_for_clear(display, XELPDP_PORT_M2P_MSGBUS_CTL(display, port, lane),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_M2P_TRANSACTION_PENDING,
XELPDP_MSGBUS_TIMEOUT_SLOW)) {
drm_dbg_kms(display->drm,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
"PHY %c Timeout waiting for previous transaction to complete. Reset the bus.\n",
phy_name(phy));
intel_cx0_bus_reset(encoder, lane);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
intel_de_rmw(display, buf_ctl2_reg,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_get_powerdown_update(INTEL_CX0_BOTH_LANES),
intel_cx0_get_powerdown_update(lane_mask));
/* Update Timeout Value */
if (intel_de_wait_custom(display, buf_ctl2_reg,
intel_cx0_get_powerdown_update(lane_mask), 0,
XELPDP_PORT_POWERDOWN_UPDATE_TIMEOUT_US, 0, NULL))
drm_warn(display->drm,
"PHY %c failed to bring out of Lane reset after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PORT_RESET_START_TIMEOUT_US);
}
static void intel_cx0_setup_powerdown(struct intel_encoder *encoder)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
intel_de_rmw(display, XELPDP_PORT_BUF_CTL2(display, port),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_POWER_STATE_READY_MASK,
XELPDP_POWER_STATE_READY(CX0_P2_STATE_READY));
intel_de_rmw(display, XELPDP_PORT_BUF_CTL3(display, port),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_POWER_STATE_ACTIVE_MASK |
XELPDP_PLL_LANE_STAGGERING_DELAY_MASK,
XELPDP_POWER_STATE_ACTIVE(CX0_P0_STATE_ACTIVE) |
XELPDP_PLL_LANE_STAGGERING_DELAY(0));
}
static u32 intel_cx0_get_pclk_refclk_request(u8 lane_mask)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_PCLK_REFCLK_REQUEST(lane);
return val;
}
static u32 intel_cx0_get_pclk_refclk_ack(u8 lane_mask)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_PCLK_REFCLK_ACK(lane);
return val;
}
static void intel_cx0_phy_lane_reset(struct intel_encoder *encoder,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
bool lane_reversal)
{
struct intel_display *display = to_intel_display(encoder);
enum port port = encoder->port;
enum phy phy = intel_encoder_to_phy(encoder);
u8 owned_lane_mask = intel_cx0_get_owned_lane_mask(encoder);
u8 lane_mask = lane_reversal ? INTEL_CX0_LANE1 : INTEL_CX0_LANE0;
u32 lane_pipe_reset = owned_lane_mask == INTEL_CX0_BOTH_LANES
? XELPDP_LANE_PIPE_RESET(0) | XELPDP_LANE_PIPE_RESET(1)
: XELPDP_LANE_PIPE_RESET(0);
u32 lane_phy_current_status = owned_lane_mask == INTEL_CX0_BOTH_LANES
? (XELPDP_LANE_PHY_CURRENT_STATUS(0) |
XELPDP_LANE_PHY_CURRENT_STATUS(1))
: XELPDP_LANE_PHY_CURRENT_STATUS(0);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_de_wait_custom(display, XELPDP_PORT_BUF_CTL1(display, port),
XELPDP_PORT_BUF_SOC_PHY_READY,
XELPDP_PORT_BUF_SOC_PHY_READY,
XELPDP_PORT_BUF_SOC_READY_TIMEOUT_US, 0, NULL))
drm_warn(display->drm,
"PHY %c failed to bring out of SOC reset after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PORT_BUF_SOC_READY_TIMEOUT_US);
intel_de_rmw(display, XELPDP_PORT_BUF_CTL2(display, port), lane_pipe_reset,
lane_pipe_reset);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_de_wait_custom(display, XELPDP_PORT_BUF_CTL2(display, port),
lane_phy_current_status, lane_phy_current_status,
XELPDP_PORT_RESET_START_TIMEOUT_US, 0, NULL))
drm_warn(display->drm,
"PHY %c failed to bring out of Lane reset after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PORT_RESET_START_TIMEOUT_US);
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, port),
intel_cx0_get_pclk_refclk_request(owned_lane_mask),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_get_pclk_refclk_request(lane_mask));
if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, port),
intel_cx0_get_pclk_refclk_ack(owned_lane_mask),
intel_cx0_get_pclk_refclk_ack(lane_mask),
XELPDP_REFCLK_ENABLE_TIMEOUT_US, 0, NULL))
drm_warn(display->drm,
"PHY %c failed to request refclk after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_REFCLK_ENABLE_TIMEOUT_US);
intel_cx0_powerdown_change_sequence(encoder, INTEL_CX0_BOTH_LANES,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
CX0_P2_STATE_RESET);
intel_cx0_setup_powerdown(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_de_rmw(display, XELPDP_PORT_BUF_CTL2(display, port), lane_pipe_reset, 0);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_de_wait_for_clear(display, XELPDP_PORT_BUF_CTL2(display, port),
lane_phy_current_status,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_PORT_RESET_END_TIMEOUT))
drm_warn(display->drm,
"PHY %c failed to bring out of Lane reset after %dms.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PORT_RESET_END_TIMEOUT);
}
static void intel_cx0_program_phy_lane(struct intel_encoder *encoder, int lane_count,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
bool lane_reversal)
{
int i;
u8 disables;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
bool dp_alt_mode = intel_tc_port_in_dp_alt_mode(enc_to_dig_port(encoder));
u8 owned_lane_mask = intel_cx0_get_owned_lane_mask(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_encoder_is_c10phy(encoder))
intel_cx0_rmw(encoder, owned_lane_mask,
PHY_C10_VDR_CONTROL(1), 0,
C10_VDR_CTRL_MSGBUS_ACCESS,
MB_WRITE_COMMITTED);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (lane_reversal)
disables = REG_GENMASK8(3, 0) >> lane_count;
else
disables = REG_GENMASK8(3, 0) << lane_count;
if (dp_alt_mode && lane_count == 1) {
disables &= ~REG_GENMASK8(1, 0);
disables |= REG_FIELD_PREP8(REG_GENMASK8(1, 0), 0x1);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
for (i = 0; i < 4; i++) {
int tx = i % 2 + 1;
u8 lane_mask = i < 2 ? INTEL_CX0_LANE0 : INTEL_CX0_LANE1;
if (!(owned_lane_mask & lane_mask))
continue;
intel_cx0_rmw(encoder, lane_mask, PHY_CX0_TX_CONTROL(tx, 2),
CONTROL2_DISABLE_SINGLE_TX,
disables & BIT(i) ? CONTROL2_DISABLE_SINGLE_TX : 0,
MB_WRITE_COMMITTED);
}
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
if (intel_encoder_is_c10phy(encoder))
intel_cx0_rmw(encoder, owned_lane_mask,
PHY_C10_VDR_CONTROL(1), 0,
C10_VDR_CTRL_UPDATE_CFG,
MB_WRITE_COMMITTED);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
static u32 intel_cx0_get_pclk_pll_request(u8 lane_mask)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_PCLK_PLL_REQUEST(lane);
return val;
}
static u32 intel_cx0_get_pclk_pll_ack(u8 lane_mask)
{
u32 val = 0;
int lane = 0;
for_each_cx0_lane_in_mask(lane_mask, lane)
val |= XELPDP_LANE_PCLK_PLL_ACK(lane);
return val;
}
static void __intel_cx0pll_enable(struct intel_encoder *encoder,
const struct intel_cx0pll_state *pll_state,
bool is_dp, int port_clock, int lane_count)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
bool lane_reversal = dig_port->lane_reversal;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
u8 maxpclk_lane = lane_reversal ? INTEL_CX0_LANE1 :
INTEL_CX0_LANE0;
intel_wakeref_t wakeref = intel_cx0_phy_transaction_begin(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 1. Program PORT_CLOCK_CTL REGISTER to configure
* clock muxes, gating and SSC
*/
intel_program_port_clock_ctl(encoder, pll_state, is_dp, port_clock, lane_reversal);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* 2. Bring PHY out of reset. */
intel_cx0_phy_lane_reset(encoder, lane_reversal);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 3. Change Phy power state to Ready.
* TODO: For DP alt mode use only one lane.
*/
intel_cx0_powerdown_change_sequence(encoder, INTEL_CX0_BOTH_LANES,
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
CX0_P2_STATE_READY);
/*
* 4. Program PORT_MSGBUS_TIMER register's Message Bus Timer field to 0xA000.
* (This is done inside intel_cx0_phy_transaction_begin(), since we would need
* the right timer thresholds for readouts too.)
*/
/* 5. Program PHY internal PLL internal registers. */
if (intel_encoder_is_c10phy(encoder))
intel_c10_pll_program(display, encoder, &pll_state->c10);
else
intel_c20_pll_program(display, encoder, &pll_state->c20, is_dp, port_clock);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 6. Program the enabled and disabled owned PHY lane
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
* transmitters over message bus
*/
intel_cx0_program_phy_lane(encoder, lane_count, lane_reversal);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 7. Follow the Display Voltage Frequency Switching - Sequence
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
* Before Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 8. Program DDI_CLK_VALFREQ to match intended DDI
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
* clock frequency.
*/
intel_de_write(display, DDI_CLK_VALFREQ(encoder->port), port_clock);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 9. Set PORT_CLOCK_CTL register PCLK PLL Request
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
* LN<Lane for maxPCLK> to "1" to enable PLL.
*/
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_get_pclk_pll_request(INTEL_CX0_BOTH_LANES),
intel_cx0_get_pclk_pll_request(maxpclk_lane));
/* 10. Poll on PORT_CLOCK_CTL PCLK PLL Ack LN<Lane for maxPCLK> == "1". */
if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
intel_cx0_get_pclk_pll_ack(INTEL_CX0_BOTH_LANES),
intel_cx0_get_pclk_pll_ack(maxpclk_lane),
XELPDP_PCLK_PLL_ENABLE_TIMEOUT_US, 0, NULL))
drm_warn(display->drm, "Port %c PLL not locked after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PCLK_PLL_ENABLE_TIMEOUT_US);
/*
* 11. Follow the Display Voltage Frequency Switching Sequence After
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/* TODO: enable TBT-ALT mode */
intel_cx0_phy_transaction_end(encoder, wakeref);
}
static void intel_cx0pll_enable(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
__intel_cx0pll_enable(encoder, &crtc_state->dpll_hw_state.cx0pll,
intel_crtc_has_dp_encoder(crtc_state),
crtc_state->port_clock, crtc_state->lane_count);
}
int intel_mtl_tbt_calc_port_clock(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
u32 clock, val;
val = intel_de_read(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port));
clock = XELPDP_DDI_CLOCK_SELECT_GET(display, val);
drm_WARN_ON(display->drm, !(val & XELPDP_FORWARD_CLOCK_UNGATE));
drm_WARN_ON(display->drm, !(val & XELPDP_TBT_CLOCK_REQUEST));
drm_WARN_ON(display->drm, !(val & XELPDP_TBT_CLOCK_ACK));
switch (clock) {
case XELPDP_DDI_CLOCK_SELECT_TBT_162:
return 162000;
case XELPDP_DDI_CLOCK_SELECT_TBT_270:
return 270000;
case XELPDP_DDI_CLOCK_SELECT_TBT_540:
return 540000;
case XELPDP_DDI_CLOCK_SELECT_TBT_810:
return 810000;
case XELPDP_DDI_CLOCK_SELECT_TBT_312_5:
return 1000000;
case XELPDP_DDI_CLOCK_SELECT_TBT_625:
return 2000000;
default:
MISSING_CASE(clock);
return 162000;
}
}
static int intel_mtl_tbt_clock_select(struct intel_display *display,
int clock)
{
switch (clock) {
case 162000:
return XELPDP_DDI_CLOCK_SELECT_TBT_162;
case 270000:
return XELPDP_DDI_CLOCK_SELECT_TBT_270;
case 540000:
return XELPDP_DDI_CLOCK_SELECT_TBT_540;
case 810000:
return XELPDP_DDI_CLOCK_SELECT_TBT_810;
case 1000000:
if (DISPLAY_VER(display) < 30) {
drm_WARN_ON(display->drm, "UHBR10 not supported for the platform\n");
return XELPDP_DDI_CLOCK_SELECT_TBT_162;
}
return XELPDP_DDI_CLOCK_SELECT_TBT_312_5;
case 2000000:
if (DISPLAY_VER(display) < 30) {
drm_WARN_ON(display->drm, "UHBR20 not supported for the platform\n");
return XELPDP_DDI_CLOCK_SELECT_TBT_162;
}
return XELPDP_DDI_CLOCK_SELECT_TBT_625;
default:
MISSING_CASE(clock);
return XELPDP_DDI_CLOCK_SELECT_TBT_162;
}
}
static void intel_mtl_tbt_pll_enable(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
u32 val = 0;
u32 mask;
/*
* 1. Program PORT_CLOCK_CTL REGISTER to configure
* clock muxes, gating and SSC
*/
mask = XELPDP_DDI_CLOCK_SELECT_MASK(display);
val |= XELPDP_DDI_CLOCK_SELECT_PREP(display,
intel_mtl_tbt_clock_select(display, crtc_state->port_clock));
mask |= XELPDP_FORWARD_CLOCK_UNGATE;
val |= XELPDP_FORWARD_CLOCK_UNGATE;
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
mask, val);
/* 2. Read back PORT_CLOCK_CTL REGISTER */
val = intel_de_read(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port));
/*
* 3. Follow the Display Voltage Frequency Switching - Sequence
* Before Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 4. Set PORT_CLOCK_CTL register TBT CLOCK Request to "1" to enable PLL.
*/
val |= XELPDP_TBT_CLOCK_REQUEST;
intel_de_write(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port), val);
/* 5. Poll on PORT_CLOCK_CTL TBT CLOCK Ack == "1". */
if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_TBT_CLOCK_ACK,
XELPDP_TBT_CLOCK_ACK,
100, 0, NULL))
drm_warn(display->drm,
"[ENCODER:%d:%s][%c] PHY PLL not locked after 100us.\n",
encoder->base.base.id, encoder->base.name, phy_name(phy));
/*
* 6. Follow the Display Voltage Frequency Switching Sequence After
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 7. Program DDI_CLK_VALFREQ to match intended DDI
* clock frequency.
*/
intel_de_write(display, DDI_CLK_VALFREQ(encoder->port),
crtc_state->port_clock);
}
void intel_mtl_pll_enable(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
if (intel_tc_port_in_tbt_alt_mode(dig_port))
intel_mtl_tbt_pll_enable(encoder, crtc_state);
else
intel_cx0pll_enable(encoder, crtc_state);
}
/*
* According to HAS we need to enable MAC Transmitting LFPS in the "PHY Common
* Control 0" PIPE register in case of AUX Less ALPM is going to be used. This
* function is doing that and is called by link retrain sequence.
*/
void intel_lnl_mac_transmit_lfps(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
struct intel_display *display = to_intel_display(encoder);
u8 owned_lane_mask = intel_cx0_get_owned_lane_mask(encoder);
bool enable = intel_alpm_is_alpm_aux_less(enc_to_intel_dp(encoder),
crtc_state);
int i;
if (DISPLAY_VER(display) < 20)
return;
for (i = 0; i < 4; i++) {
int tx = i % 2 + 1;
u8 lane_mask = i < 2 ? INTEL_CX0_LANE0 : INTEL_CX0_LANE1;
if (!(owned_lane_mask & lane_mask))
continue;
intel_cx0_rmw(encoder, lane_mask, PHY_CMN1_CONTROL(tx, 0),
CONTROL0_MAC_TRANSMIT_LFPS,
enable ? CONTROL0_MAC_TRANSMIT_LFPS : 0,
MB_WRITE_COMMITTED);
}
}
static u8 cx0_power_control_disable_val(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
if (intel_encoder_is_c10phy(encoder))
return CX0_P2PG_STATE_DISABLE;
if ((display->platform.battlemage && encoder->port == PORT_A) ||
(DISPLAY_VER(display) >= 30 && encoder->type == INTEL_OUTPUT_EDP))
return CX0_P2PG_STATE_DISABLE;
return CX0_P4PG_STATE_DISABLE;
}
static void intel_cx0pll_disable(struct intel_encoder *encoder)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
intel_wakeref_t wakeref = intel_cx0_phy_transaction_begin(encoder);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/* 1. Change owned PHY lane power to Disable state. */
intel_cx0_powerdown_change_sequence(encoder, INTEL_CX0_BOTH_LANES,
cx0_power_control_disable_val(encoder));
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 2. Follow the Display Voltage Frequency Switching Sequence Before
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 3. Set PORT_CLOCK_CTL register PCLK PLL Request LN<Lane for maxPCLK>
* to "0" to disable PLL.
*/
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
intel_cx0_get_pclk_pll_request(INTEL_CX0_BOTH_LANES) |
intel_cx0_get_pclk_refclk_request(INTEL_CX0_BOTH_LANES), 0);
/* 4. Program DDI_CLK_VALFREQ to 0. */
intel_de_write(display, DDI_CLK_VALFREQ(encoder->port), 0);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
/*
* 5. Poll on PORT_CLOCK_CTL PCLK PLL Ack LN<Lane for maxPCLK**> == "0".
*/
if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
intel_cx0_get_pclk_pll_ack(INTEL_CX0_BOTH_LANES) |
intel_cx0_get_pclk_refclk_ack(INTEL_CX0_BOTH_LANES), 0,
XELPDP_PCLK_PLL_DISABLE_TIMEOUT_US, 0, NULL))
drm_warn(display->drm,
"Port %c PLL not unlocked after %dus.\n",
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
phy_name(phy), XELPDP_PCLK_PLL_DISABLE_TIMEOUT_US);
/*
* 6. Follow the Display Voltage Frequency Switching Sequence After
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/* 7. Program PORT_CLOCK_CTL register to disable and gate clocks. */
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_DDI_CLOCK_SELECT_MASK(display), 0);
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
XELPDP_FORWARD_CLOCK_UNGATE, 0);
intel_cx0_phy_transaction_end(encoder, wakeref);
}
static bool intel_cx0_pll_is_enabled(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
u8 lane = dig_port->lane_reversal ? INTEL_CX0_LANE1 : INTEL_CX0_LANE0;
return intel_de_read(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port)) &
intel_cx0_get_pclk_pll_request(lane);
}
static void intel_mtl_tbt_pll_disable(struct intel_encoder *encoder)
{
struct intel_display *display = to_intel_display(encoder);
enum phy phy = intel_encoder_to_phy(encoder);
/*
* 1. Follow the Display Voltage Frequency Switching Sequence Before
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 2. Set PORT_CLOCK_CTL register TBT CLOCK Request to "0" to disable PLL.
*/
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_TBT_CLOCK_REQUEST, 0);
/* 3. Poll on PORT_CLOCK_CTL TBT CLOCK Ack == "0". */
if (intel_de_wait_custom(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_TBT_CLOCK_ACK, 0, 10, 0, NULL))
drm_warn(display->drm,
"[ENCODER:%d:%s][%c] PHY PLL not unlocked after 10us.\n",
encoder->base.base.id, encoder->base.name, phy_name(phy));
/*
* 4. Follow the Display Voltage Frequency Switching Sequence After
* Frequency Change. We handle this step in bxt_set_cdclk().
*/
/*
* 5. Program PORT CLOCK CTRL register to disable and gate clocks
*/
intel_de_rmw(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port),
XELPDP_DDI_CLOCK_SELECT_MASK(display) |
XELPDP_FORWARD_CLOCK_UNGATE, 0);
/* 6. Program DDI_CLK_VALFREQ to 0. */
intel_de_write(display, DDI_CLK_VALFREQ(encoder->port), 0);
}
void intel_mtl_pll_disable(struct intel_encoder *encoder)
{
struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
if (intel_tc_port_in_tbt_alt_mode(dig_port))
intel_mtl_tbt_pll_disable(encoder);
else
intel_cx0pll_disable(encoder);
}
enum icl_port_dpll_id
intel_mtl_port_pll_type(struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state)
{
struct intel_display *display = to_intel_display(encoder);
u32 val, clock;
/*
* TODO: Determine the PLL type from the SW state, once MTL PLL
* handling is done via the standard shared DPLL framework.
*/
val = intel_de_read(display, XELPDP_PORT_CLOCK_CTL(display, encoder->port));
clock = XELPDP_DDI_CLOCK_SELECT_GET(display, val);
if (clock == XELPDP_DDI_CLOCK_SELECT_MAXPCLK ||
clock == XELPDP_DDI_CLOCK_SELECT_DIV18CLK)
return ICL_PORT_DPLL_MG_PHY;
else
return ICL_PORT_DPLL_DEFAULT;
}
static void intel_c10pll_state_verify(const struct intel_crtc_state *state,
struct intel_crtc *crtc,
struct intel_encoder *encoder,
struct intel_c10pll_state *mpllb_hw_state)
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
{
struct intel_display *display = to_intel_display(state);
const struct intel_c10pll_state *mpllb_sw_state = &state->dpll_hw_state.cx0pll.c10;
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
int i;
for (i = 0; i < ARRAY_SIZE(mpllb_sw_state->pll); i++) {
u8 expected = mpllb_sw_state->pll[i];
INTEL_DISPLAY_STATE_WARN(display, mpllb_hw_state->pll[i] != expected,
"[CRTC:%d:%s] mismatch in C10MPLLB: Register[%d] (expected 0x%02x, found 0x%02x)",
crtc->base.base.id, crtc->base.name, i,
expected, mpllb_hw_state->pll[i]);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
INTEL_DISPLAY_STATE_WARN(display, mpllb_hw_state->tx != mpllb_sw_state->tx,
"[CRTC:%d:%s] mismatch in C10MPLLB: Register TX0 (expected 0x%02x, found 0x%02x)",
crtc->base.base.id, crtc->base.name,
mpllb_sw_state->tx, mpllb_hw_state->tx);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
INTEL_DISPLAY_STATE_WARN(display, mpllb_hw_state->cmn != mpllb_sw_state->cmn,
"[CRTC:%d:%s] mismatch in C10MPLLB: Register CMN0 (expected 0x%02x, found 0x%02x)",
crtc->base.base.id, crtc->base.name,
mpllb_sw_state->cmn, mpllb_hw_state->cmn);
drm/i915/mtl: Add Support for C10 PHY message bus and pll programming XELPDP has C10 and C20 phys from Synopsys to drive displays. Each phy has a dedicated PIPE 5.2 Message bus for configuration. This message bus is used to configure the phy internal registers. XELPDP has C10 phys to drive output to the EDP and the native output from the display engine. Add structures, programming hardware state readout logic. Port clock calculations are similar to DG2. Use the DG2 formulae to calculate the port clock but use the relevant pll signals. Note: PHY lane 0 is always used for PLL programming. Add sequences for C10 phy enable/disable phy lane reset, powerdown change sequence and phy lane programming. Bspec: 64539, 64568, 64599, 65100, 65101, 65450, 65451, 67610, 67636 v2: Squash patches related to C10 phy message bus and pll programming support (Jani) Move register definitions to a new file i.e. intel_cx0_reg_defs.h (Jani) Move macro definitions (Jani) DP rates as separate patch (Jani) Spin out xelpdp register definitions into a separate file (Jani) Replace macro to select registers based on phy lane with function calls (Jani) Fix styling issues (Jani) Call XELPDP_PORT_P2M_MSGBUS_STATUS() with port instead of phy (Lucas) v3: Move clear request flag into try-loop v4: On PHY idle change drm_err_once() as drm_dbg_kms() (Jani) use __intel_de_wait_for_register() instead of __intel_wait_for_register and uncomment intel_uncore.h (Jani) Add DP-alt support for PHY lane programming (Khaled) v4: Add tx and cmn on c10mpllb_state (Imre) Add missing waits for pending transactions between two message bus writes (Imre) General cleanups and simplifications (Imre) v5: Few nit cleanups from rev4 (imre) s/dev_priv/i915/ , s/c10mpllb/c10pll/ (RK) Rebase v6: Move the mtl code from intel_c10pll_calc_port_clock to mtl function Fix typo in comment for REG_FIELD_PREP8 definition(Imre) Cc: Mika Kahola <mika.kahola@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Gustavo Sousa <gustavo.sousa@intel.com> Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com> Signed-off-by: Mika Kahola <mika.kahola@intel.com> Reviewed-by: Imre Deak <imre.deak@intel.com> (v4) Link: https://patchwork.freedesktop.org/patch/msgid/20230413212443.1504245-4-radhakrishna.sripada@intel.com
2023-04-13 14:24:37 -07:00
}
void intel_cx0pll_readout_hw_state(struct intel_encoder *encoder,
struct intel_cx0pll_state *pll_state)
{
pll_state->use_c10 = false;
pll_state->tbt_mode = intel_tc_port_in_tbt_alt_mode(enc_to_dig_port(encoder));
if (pll_state->tbt_mode)
return;
if (intel_encoder_is_c10phy(encoder)) {
intel_c10pll_readout_hw_state(encoder, &pll_state->c10);
pll_state->use_c10 = true;
} else {
intel_c20pll_readout_hw_state(encoder, &pll_state->c20);
}
}
static bool mtl_compare_hw_state_c10(const struct intel_c10pll_state *a,
const struct intel_c10pll_state *b)
{
if (a->tx != b->tx)
return false;
if (a->cmn != b->cmn)
return false;
if (memcmp(&a->pll, &b->pll, sizeof(a->pll)) != 0)
return false;
return true;
}
static bool mtl_compare_hw_state_c20(const struct intel_c20pll_state *a,
const struct intel_c20pll_state *b)
{
if (memcmp(&a->tx, &b->tx, sizeof(a->tx)) != 0)
return false;
if (memcmp(&a->cmn, &b->cmn, sizeof(a->cmn)) != 0)
return false;
if (a->tx[0] & C20_PHY_USE_MPLLB) {
if (memcmp(&a->mpllb, &b->mpllb, sizeof(a->mpllb)) != 0)
return false;
} else {
if (memcmp(&a->mplla, &b->mplla, sizeof(a->mplla)) != 0)
return false;
}
return true;
}
bool intel_cx0pll_compare_hw_state(const struct intel_cx0pll_state *a,
const struct intel_cx0pll_state *b)
{
if (a->tbt_mode || b->tbt_mode)
return true;
if (a->use_c10 != b->use_c10)
return false;
if (a->use_c10)
return mtl_compare_hw_state_c10(&a->c10,
&b->c10);
else
return mtl_compare_hw_state_c20(&a->c20,
&b->c20);
}
int intel_cx0pll_calc_port_clock(struct intel_encoder *encoder,
const struct intel_cx0pll_state *pll_state)
{
if (intel_encoder_is_c10phy(encoder))
return intel_c10pll_calc_port_clock(encoder, &pll_state->c10);
return intel_c20pll_calc_port_clock(encoder, &pll_state->c20);
}
static void intel_c20pll_state_verify(const struct intel_crtc_state *state,
struct intel_crtc *crtc,
struct intel_encoder *encoder,
struct intel_c20pll_state *mpll_hw_state)
{
struct intel_display *display = to_intel_display(state);
const struct intel_c20pll_state *mpll_sw_state = &state->dpll_hw_state.cx0pll.c20;
bool sw_use_mpllb = intel_c20phy_use_mpllb(mpll_sw_state);
bool hw_use_mpllb = intel_c20phy_use_mpllb(mpll_hw_state);
int clock = intel_c20pll_calc_port_clock(encoder, mpll_sw_state);
int i;
INTEL_DISPLAY_STATE_WARN(display, mpll_hw_state->clock != clock,
"[CRTC:%d:%s] mismatch in C20: Register CLOCK (expected %d, found %d)",
crtc->base.base.id, crtc->base.name,
mpll_sw_state->clock, mpll_hw_state->clock);
INTEL_DISPLAY_STATE_WARN(display, sw_use_mpllb != hw_use_mpllb,
"[CRTC:%d:%s] mismatch in C20: Register MPLLB selection (expected %d, found %d)",
crtc->base.base.id, crtc->base.name,
sw_use_mpllb, hw_use_mpllb);
if (hw_use_mpllb) {
for (i = 0; i < ARRAY_SIZE(mpll_sw_state->mpllb); i++) {
INTEL_DISPLAY_STATE_WARN(display, mpll_hw_state->mpllb[i] != mpll_sw_state->mpllb[i],
"[CRTC:%d:%s] mismatch in C20MPLLB: Register[%d] (expected 0x%04x, found 0x%04x)",
crtc->base.base.id, crtc->base.name, i,
mpll_sw_state->mpllb[i], mpll_hw_state->mpllb[i]);
}
} else {
for (i = 0; i < ARRAY_SIZE(mpll_sw_state->mplla); i++) {
INTEL_DISPLAY_STATE_WARN(display, mpll_hw_state->mplla[i] != mpll_sw_state->mplla[i],
"[CRTC:%d:%s] mismatch in C20MPLLA: Register[%d] (expected 0x%04x, found 0x%04x)",
crtc->base.base.id, crtc->base.name, i,
mpll_sw_state->mplla[i], mpll_hw_state->mplla[i]);
}
}
for (i = 0; i < ARRAY_SIZE(mpll_sw_state->tx); i++) {
INTEL_DISPLAY_STATE_WARN(display, mpll_hw_state->tx[i] != mpll_sw_state->tx[i],
"[CRTC:%d:%s] mismatch in C20: Register TX[%i] (expected 0x%04x, found 0x%04x)",
crtc->base.base.id, crtc->base.name, i,
mpll_sw_state->tx[i], mpll_hw_state->tx[i]);
}
for (i = 0; i < ARRAY_SIZE(mpll_sw_state->cmn); i++) {
INTEL_DISPLAY_STATE_WARN(display, mpll_hw_state->cmn[i] != mpll_sw_state->cmn[i],
"[CRTC:%d:%s] mismatch in C20: Register CMN[%i] (expected 0x%04x, found 0x%04x)",
crtc->base.base.id, crtc->base.name, i,
mpll_sw_state->cmn[i], mpll_hw_state->cmn[i]);
}
}
void intel_cx0pll_state_verify(struct intel_atomic_state *state,
struct intel_crtc *crtc)
{
struct intel_display *display = to_intel_display(state);
const struct intel_crtc_state *new_crtc_state =
intel_atomic_get_new_crtc_state(state, crtc);
struct intel_encoder *encoder;
struct intel_cx0pll_state mpll_hw_state = {};
if (DISPLAY_VER(display) < 14)
return;
if (!new_crtc_state->hw.active)
return;
/* intel_get_crtc_new_encoder() only works for modeset/fastset commits */
if (!intel_crtc_needs_modeset(new_crtc_state) &&
!intel_crtc_needs_fastset(new_crtc_state))
return;
encoder = intel_get_crtc_new_encoder(state, new_crtc_state);
intel_cx0pll_readout_hw_state(encoder, &mpll_hw_state);
if (mpll_hw_state.tbt_mode)
return;
if (intel_encoder_is_c10phy(encoder))
intel_c10pll_state_verify(new_crtc_state, crtc, encoder, &mpll_hw_state.c10);
else
intel_c20pll_state_verify(new_crtc_state, crtc, encoder, &mpll_hw_state.c20);
}
/*
* WA 14022081154
* The dedicated display PHYs reset to a power state that blocks S0ix, increasing idle
* system power. After a system reset (cold boot, S3/4/5, warm reset) if a dedicated
* PHY is not being brought up shortly, use these steps to move the PHY to the lowest
* power state to save power. For PTL the workaround is needed only for port A. Port B
* is not connected.
*
* 1. Follow the PLL Enable Sequence, using any valid frequency such as DP 1.62 GHz.
* This brings lanes out of reset and enables the PLL to allow powerdown to be moved
* to the Disable state.
* 2. Follow PLL Disable Sequence. This moves powerdown to the Disable state and disables the PLL.
*/
void intel_cx0_pll_power_save_wa(struct intel_display *display)
{
struct intel_encoder *encoder;
if (DISPLAY_VER(display) != 30)
return;
for_each_intel_encoder(display->drm, encoder) {
struct intel_cx0pll_state pll_state = {};
int port_clock = 162000;
if (!intel_encoder_is_dig_port(encoder))
continue;
if (!intel_encoder_is_c10phy(encoder))
continue;
if (intel_cx0_pll_is_enabled(encoder))
continue;
if (intel_c10pll_calc_state_from_table(encoder,
mtl_c10_edp_tables,
true, port_clock,
&pll_state) < 0) {
drm_WARN_ON(display->drm,
"Unable to calc C10 state from the tables\n");
continue;
}
drm_dbg_kms(display->drm,
"[ENCODER:%d:%s] Applying power saving workaround on disabled PLL\n",
encoder->base.base.id, encoder->base.name);
__intel_cx0pll_enable(encoder, &pll_state, true, port_clock, 4);
intel_cx0pll_disable(encoder);
}
}