mirror of
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2025-08-05 16:54:27 +00:00
No description
80b3fd474c
This commit removes the cpus_read_lock() and cpus_read_unlock() calls
from rcu_barrier(), thus allowing CPUs to come and go during the course
of rcu_barrier() execution. Posting of the ->barrier_head callbacks does
synchronize with portions of RCU's CPU-hotplug notifiers, but these locks
are held for short time periods on both sides. Thus, full CPU-hotplug
operations could both start and finish during the execution of a given
rcu_barrier() invocation.
Additional synchronization is provided by a global ->barrier_lock.
Since the ->barrier_lock is only used during rcu_barrier() execution and
during onlining/offlining a CPU, the contention for this lock should
be low. It might be tempting to make use of a per-CPU lock just on
general principles, but straightforward attempts to do this have the
problems shown below.
Initial state: 3 CPUs present, CPU 0 and CPU1 do not have
any callback and CPU2 has callbacks.
1. CPU0 calls rcu_barrier().
2. CPU1 starts offlining for CPU2. CPU1 calls
rcutree_migrate_callbacks(). rcu_barrier_entrain() is called
from rcutree_migrate_callbacks(), with CPU2's rdp->barrier_lock.
It does not entrain ->barrier_head for CPU2, as rcu_barrier()
on CPU0 hasn't started the barrier sequence (by calling
rcu_seq_start(&rcu_state.barrier_sequence)) yet.
3. CPU0 starts new barrier sequence. It iterates over
CPU0 and CPU1, after acquiring their per-cpu ->barrier_lock
and finds 0 segcblist length. It updates ->barrier_seq_snap
for CPU0 and CPU1 and continues loop iteration to CPU2.
for_each_possible_cpu(cpu) {
raw_spin_lock_irqsave(&rdp->barrier_lock, flags);
if (!rcu_segcblist_n_cbs(&rdp->cblist)) {
WRITE_ONCE(rdp->barrier_seq_snap, gseq);
raw_spin_unlock_irqrestore(&rdp->barrier_lock, flags);
rcu_barrier_trace(TPS("NQ"), cpu, rcu_state.barrier_sequence);
continue;
}
4. rcutree_migrate_callbacks() completes execution on CPU1.
Segcblist len for CPU2 becomes 0.
5. The loop iteration on CPU0, checks rcu_segcblist_n_cbs(&rdp->cblist)
for CPU2 and completes the loop iteration after setting
->barrier_seq_snap.
6. As there isn't any ->barrier_head callback entrained; at
this point, rcu_barrier() in CPU0 returns.
7. The callbacks, which migrated from CPU2 to CPU1, execute.
Straightforward per-CPU locking is also subject to the following race
condition noted by Boqun Feng:
1. CPU0 calls rcu_barrier(), starting a new barrier sequence by invoking
rcu_seq_start() and init_completion(), but does not yet initialize
rcu_state.barrier_cpu_count.
2. CPU1 starts offlining for CPU2, calling rcutree_migrate_callbacks(),
which in turn calls rcu_barrier_entrain() holding CPU2's.
rdp->barrier_lock. It then entrains ->barrier_head for CPU2
and atomically increments rcu_state.barrier_cpu_count, which is
unfortunately not yet initialized to the value 2.
3. The just-entrained RCU callback is invoked. It atomically
decrements rcu_state.barrier_cpu_count and sees that it is
now zero. This callback therefore invokes complete().
4. CPU0 continues executing rcu_barrier(), but is not blocked
by its call to wait_for_completion(). This results in rcu_barrier()
returning before all pre-existing callbacks have been invoked,
which is a bug.
Therefore, synchronization is provided by rcu_state.barrier_lock,
which is also held across the initialization sequence, especially the
rcu_seq_start() and the atomic_set() that sets rcu_state.barrier_cpu_count
to the value 2. In addition, this lock is held when entraining the
rcu_barrier() callback, when deciding whether or not a CPU has callbacks
that rcu_barrier() must wait on, when setting the ->qsmaskinitnext for
incoming CPUs, and when migrating callbacks from a CPU that is going
offline.
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Co-developed-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Signed-off-by: Neeraj Upadhyay <quic_neeraju@quicinc.com>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
|
||
|---|---|---|
| arch | ||
| block | ||
| certs | ||
| crypto | ||
| Documentation | ||
| drivers | ||
| fs | ||
| include | ||
| init | ||
| ipc | ||
| kernel | ||
| lib | ||
| LICENSES | ||
| mm | ||
| net | ||
| samples | ||
| scripts | ||
| security | ||
| sound | ||
| tools | ||
| usr | ||
| virt | ||
| .clang-format | ||
| .cocciconfig | ||
| .get_maintainer.ignore | ||
| .gitattributes | ||
| .gitignore | ||
| .mailmap | ||
| COPYING | ||
| CREDITS | ||
| Kbuild | ||
| Kconfig | ||
| MAINTAINERS | ||
| Makefile | ||
| README | ||
Linux kernel
============
There are several guides for kernel developers and users. These guides can
be rendered in a number of formats, like HTML and PDF. Please read
Documentation/admin-guide/README.rst first.
In order to build the documentation, use ``make htmldocs`` or
``make pdfdocs``. The formatted documentation can also be read online at:
https://www.kernel.org/doc/html/latest/
There are various text files in the Documentation/ subdirectory,
several of them using the Restructured Text markup notation.
Please read the Documentation/process/changes.rst file, as it contains the
requirements for building and running the kernel, and information about
the problems which may result by upgrading your kernel.