mirror of
				git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
				synced 2025-10-31 16:54:21 +00:00 
			
		
		
		
	 0ee44f900e
			
		
	
	
		0ee44f900e
		
	
	
	
	
		
			
			Instead of setting the message byte translate it to the appropriate host byte. As error recovery would return DID_ERROR for any non-zero message byte the translation doesn't change the error handling. Link: https://lore.kernel.org/r/20210427083046.31620-37-hare@suse.de Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
		
			
				
	
	
		
			599 lines
		
	
	
	
		
			16 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
			
		
		
	
	
			599 lines
		
	
	
	
		
			16 KiB
		
	
	
	
		
			C
		
	
	
	
	
	
| // SPDX-License-Identifier: GPL-2.0
 | |
| /*
 | |
|  * Driver for Future Domain TMC-16x0 and TMC-3260 SCSI host adapters
 | |
|  * Copyright 2019 Ondrej Zary
 | |
|  *
 | |
|  * Original driver by
 | |
|  * Rickard E. Faith, faith@cs.unc.edu
 | |
|  *
 | |
|  * Future Domain BIOS versions supported for autodetect:
 | |
|  *    2.0, 3.0, 3.2, 3.4 (1.0), 3.5 (2.0), 3.6, 3.61
 | |
|  * Chips supported:
 | |
|  *    TMC-1800, TMC-18C50, TMC-18C30, TMC-36C70
 | |
|  * Boards supported:
 | |
|  *    Future Domain TMC-1650, TMC-1660, TMC-1670, TMC-1680, TMC-1610M/MER/MEX
 | |
|  *    Future Domain TMC-3260 (PCI)
 | |
|  *    Quantum ISA-200S, ISA-250MG
 | |
|  *    Adaptec AHA-2920A (PCI) [BUT *NOT* AHA-2920C -- use aic7xxx instead]
 | |
|  *    IBM ?
 | |
|  *
 | |
|  * NOTE:
 | |
|  *
 | |
|  * The Adaptec AHA-2920C has an Adaptec AIC-7850 chip on it.
 | |
|  * Use the aic7xxx driver for this board.
 | |
|  *
 | |
|  * The Adaptec AHA-2920A has a Future Domain chip on it, so this is the right
 | |
|  * driver for that card.  Unfortunately, the boxes will probably just say
 | |
|  * "2920", so you'll have to look on the card for a Future Domain logo, or a
 | |
|  * letter after the 2920.
 | |
|  *
 | |
|  * If you have a TMC-8xx or TMC-9xx board, then this is not the driver for
 | |
|  * your board.
 | |
|  *
 | |
|  * DESCRIPTION:
 | |
|  *
 | |
|  * This is the Linux low-level SCSI driver for Future Domain TMC-1660/1680
 | |
|  * TMC-1650/1670, and TMC-3260 SCSI host adapters.  The 1650 and 1670 have a
 | |
|  * 25-pin external connector, whereas the 1660 and 1680 have a SCSI-2 50-pin
 | |
|  * high-density external connector.  The 1670 and 1680 have floppy disk
 | |
|  * controllers built in.  The TMC-3260 is a PCI bus card.
 | |
|  *
 | |
|  * Future Domain's older boards are based on the TMC-1800 chip, and this
 | |
|  * driver was originally written for a TMC-1680 board with the TMC-1800 chip.
 | |
|  * More recently, boards are being produced with the TMC-18C50 and TMC-18C30
 | |
|  * chips.
 | |
|  *
 | |
|  * Please note that the drive ordering that Future Domain implemented in BIOS
 | |
|  * versions 3.4 and 3.5 is the opposite of the order (currently) used by the
 | |
|  * rest of the SCSI industry.
 | |
|  *
 | |
|  *
 | |
|  * REFERENCES USED:
 | |
|  *
 | |
|  * "TMC-1800 SCSI Chip Specification (FDC-1800T)", Future Domain Corporation,
 | |
|  * 1990.
 | |
|  *
 | |
|  * "Technical Reference Manual: 18C50 SCSI Host Adapter Chip", Future Domain
 | |
|  * Corporation, January 1992.
 | |
|  *
 | |
|  * "LXT SCSI Products: Specifications and OEM Technical Manual (Revision
 | |
|  * B/September 1991)", Maxtor Corporation, 1991.
 | |
|  *
 | |
|  * "7213S product Manual (Revision P3)", Maxtor Corporation, 1992.
 | |
|  *
 | |
|  * "Draft Proposed American National Standard: Small Computer System
 | |
|  * Interface - 2 (SCSI-2)", Global Engineering Documents. (X3T9.2/86-109,
 | |
|  * revision 10h, October 17, 1991)
 | |
|  *
 | |
|  * Private communications, Drew Eckhardt (drew@cs.colorado.edu) and Eric
 | |
|  * Youngdale (ericy@cais.com), 1992.
 | |
|  *
 | |
|  * Private communication, Tuong Le (Future Domain Engineering department),
 | |
|  * 1994. (Disk geometry computations for Future Domain BIOS version 3.4, and
 | |
|  * TMC-18C30 detection.)
 | |
|  *
 | |
|  * Hogan, Thom. The Programmer's PC Sourcebook. Microsoft Press, 1988. Page
 | |
|  * 60 (2.39: Disk Partition Table Layout).
 | |
|  *
 | |
|  * "18C30 Technical Reference Manual", Future Domain Corporation, 1993, page
 | |
|  * 6-1.
 | |
|  */
 | |
| 
 | |
| #include <linux/module.h>
 | |
| #include <linux/interrupt.h>
 | |
| #include <linux/delay.h>
 | |
| #include <linux/pci.h>
 | |
| #include <linux/workqueue.h>
 | |
| #include <scsi/scsicam.h>
 | |
| #include <scsi/scsi_cmnd.h>
 | |
| #include <scsi/scsi_device.h>
 | |
| #include <scsi/scsi_host.h>
 | |
| #include "fdomain.h"
 | |
| 
 | |
| /*
 | |
|  * FIFO_COUNT: The host adapter has an 8K cache (host adapters based on the
 | |
|  * 18C30 chip have a 2k cache).  When this many 512 byte blocks are filled by
 | |
|  * the SCSI device, an interrupt will be raised.  Therefore, this could be as
 | |
|  * low as 0, or as high as 16.  Note, however, that values which are too high
 | |
|  * or too low seem to prevent any interrupts from occurring, and thereby lock
 | |
|  * up the machine.
 | |
|  */
 | |
| #define FIFO_COUNT	2	/* Number of 512 byte blocks before INTR */
 | |
| #define PARITY_MASK	ACTL_PAREN	/* Parity enabled, 0 = disabled */
 | |
| 
 | |
| enum chip_type {
 | |
| 	unknown		= 0x00,
 | |
| 	tmc1800		= 0x01,
 | |
| 	tmc18c50	= 0x02,
 | |
| 	tmc18c30	= 0x03,
 | |
| };
 | |
| 
 | |
| struct fdomain {
 | |
| 	int base;
 | |
| 	struct scsi_cmnd *cur_cmd;
 | |
| 	enum chip_type chip;
 | |
| 	struct work_struct work;
 | |
| };
 | |
| 
 | |
| static inline void fdomain_make_bus_idle(struct fdomain *fd)
 | |
| {
 | |
| 	outb(0, fd->base + REG_BCTL);
 | |
| 	outb(0, fd->base + REG_MCTL);
 | |
| 	if (fd->chip == tmc18c50 || fd->chip == tmc18c30)
 | |
| 		/* Clear forced intr. */
 | |
| 		outb(ACTL_RESET | ACTL_CLRFIRQ | PARITY_MASK,
 | |
| 		     fd->base + REG_ACTL);
 | |
| 	else
 | |
| 		outb(ACTL_RESET | PARITY_MASK, fd->base + REG_ACTL);
 | |
| }
 | |
| 
 | |
| static enum chip_type fdomain_identify(int port)
 | |
| {
 | |
| 	u16 id = inb(port + REG_ID_LSB) | inb(port + REG_ID_MSB) << 8;
 | |
| 
 | |
| 	switch (id) {
 | |
| 	case 0x6127:
 | |
| 		return tmc1800;
 | |
| 	case 0x60e9: /* 18c50 or 18c30 */
 | |
| 		break;
 | |
| 	default:
 | |
| 		return unknown;
 | |
| 	}
 | |
| 
 | |
| 	/* Try to toggle 32-bit mode. This only works on an 18c30 chip. */
 | |
| 	outb(CFG2_32BIT, port + REG_CFG2);
 | |
| 	if ((inb(port + REG_CFG2) & CFG2_32BIT)) {
 | |
| 		outb(0, port + REG_CFG2);
 | |
| 		if ((inb(port + REG_CFG2) & CFG2_32BIT) == 0)
 | |
| 			return tmc18c30;
 | |
| 	}
 | |
| 	/* If that failed, we are an 18c50. */
 | |
| 	return tmc18c50;
 | |
| }
 | |
| 
 | |
| static int fdomain_test_loopback(int base)
 | |
| {
 | |
| 	int i;
 | |
| 
 | |
| 	for (i = 0; i < 255; i++) {
 | |
| 		outb(i, base + REG_LOOPBACK);
 | |
| 		if (inb(base + REG_LOOPBACK) != i)
 | |
| 			return 1;
 | |
| 	}
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static void fdomain_reset(int base)
 | |
| {
 | |
| 	outb(BCTL_RST, base + REG_BCTL);
 | |
| 	mdelay(20);
 | |
| 	outb(0, base + REG_BCTL);
 | |
| 	mdelay(1150);
 | |
| 	outb(0, base + REG_MCTL);
 | |
| 	outb(PARITY_MASK, base + REG_ACTL);
 | |
| }
 | |
| 
 | |
| static int fdomain_select(struct Scsi_Host *sh, int target)
 | |
| {
 | |
| 	int status;
 | |
| 	unsigned long timeout;
 | |
| 	struct fdomain *fd = shost_priv(sh);
 | |
| 
 | |
| 	outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL);
 | |
| 	outb(BIT(sh->this_id) | BIT(target), fd->base + REG_SCSI_DATA_NOACK);
 | |
| 
 | |
| 	/* Stop arbitration and enable parity */
 | |
| 	outb(PARITY_MASK, fd->base + REG_ACTL);
 | |
| 
 | |
| 	timeout = 350;	/* 350 msec */
 | |
| 
 | |
| 	do {
 | |
| 		status = inb(fd->base + REG_BSTAT);
 | |
| 		if (status & BSTAT_BSY) {
 | |
| 			/* Enable SCSI Bus */
 | |
| 			/* (on error, should make bus idle with 0) */
 | |
| 			outb(BCTL_BUSEN, fd->base + REG_BCTL);
 | |
| 			return 0;
 | |
| 		}
 | |
| 		mdelay(1);
 | |
| 	} while (--timeout);
 | |
| 	fdomain_make_bus_idle(fd);
 | |
| 	return 1;
 | |
| }
 | |
| 
 | |
| static void fdomain_finish_cmd(struct fdomain *fd)
 | |
| {
 | |
| 	outb(0, fd->base + REG_ICTL);
 | |
| 	fdomain_make_bus_idle(fd);
 | |
| 	fd->cur_cmd->scsi_done(fd->cur_cmd);
 | |
| 	fd->cur_cmd = NULL;
 | |
| }
 | |
| 
 | |
| static void fdomain_read_data(struct scsi_cmnd *cmd)
 | |
| {
 | |
| 	struct fdomain *fd = shost_priv(cmd->device->host);
 | |
| 	unsigned char *virt, *ptr;
 | |
| 	size_t offset, len;
 | |
| 
 | |
| 	while ((len = inw(fd->base + REG_FIFO_COUNT)) > 0) {
 | |
| 		offset = scsi_bufflen(cmd) - scsi_get_resid(cmd);
 | |
| 		virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd),
 | |
| 					   &offset, &len);
 | |
| 		ptr = virt + offset;
 | |
| 		if (len & 1)
 | |
| 			*ptr++ = inb(fd->base + REG_FIFO);
 | |
| 		if (len > 1)
 | |
| 			insw(fd->base + REG_FIFO, ptr, len >> 1);
 | |
| 		scsi_set_resid(cmd, scsi_get_resid(cmd) - len);
 | |
| 		scsi_kunmap_atomic_sg(virt);
 | |
| 	}
 | |
| }
 | |
| 
 | |
| static void fdomain_write_data(struct scsi_cmnd *cmd)
 | |
| {
 | |
| 	struct fdomain *fd = shost_priv(cmd->device->host);
 | |
| 	/* 8k FIFO for pre-tmc18c30 chips, 2k FIFO for tmc18c30 */
 | |
| 	int FIFO_Size = fd->chip == tmc18c30 ? 0x800 : 0x2000;
 | |
| 	unsigned char *virt, *ptr;
 | |
| 	size_t offset, len;
 | |
| 
 | |
| 	while ((len = FIFO_Size - inw(fd->base + REG_FIFO_COUNT)) > 512) {
 | |
| 		offset = scsi_bufflen(cmd) - scsi_get_resid(cmd);
 | |
| 		if (len + offset > scsi_bufflen(cmd)) {
 | |
| 			len = scsi_bufflen(cmd) - offset;
 | |
| 			if (len == 0)
 | |
| 				break;
 | |
| 		}
 | |
| 		virt = scsi_kmap_atomic_sg(scsi_sglist(cmd), scsi_sg_count(cmd),
 | |
| 					   &offset, &len);
 | |
| 		ptr = virt + offset;
 | |
| 		if (len & 1)
 | |
| 			outb(*ptr++, fd->base + REG_FIFO);
 | |
| 		if (len > 1)
 | |
| 			outsw(fd->base + REG_FIFO, ptr, len >> 1);
 | |
| 		scsi_set_resid(cmd, scsi_get_resid(cmd) - len);
 | |
| 		scsi_kunmap_atomic_sg(virt);
 | |
| 	}
 | |
| }
 | |
| 
 | |
| static void fdomain_work(struct work_struct *work)
 | |
| {
 | |
| 	struct fdomain *fd = container_of(work, struct fdomain, work);
 | |
| 	struct Scsi_Host *sh = container_of((void *)fd, struct Scsi_Host,
 | |
| 					    hostdata);
 | |
| 	struct scsi_cmnd *cmd = fd->cur_cmd;
 | |
| 	unsigned long flags;
 | |
| 	int status;
 | |
| 	int done = 0;
 | |
| 
 | |
| 	spin_lock_irqsave(sh->host_lock, flags);
 | |
| 
 | |
| 	if (cmd->SCp.phase & in_arbitration) {
 | |
| 		status = inb(fd->base + REG_ASTAT);
 | |
| 		if (!(status & ASTAT_ARB)) {
 | |
| 			set_host_byte(cmd, DID_BUS_BUSY);
 | |
| 			fdomain_finish_cmd(fd);
 | |
| 			goto out;
 | |
| 		}
 | |
| 		cmd->SCp.phase = in_selection;
 | |
| 
 | |
| 		outb(ICTL_SEL | FIFO_COUNT, fd->base + REG_ICTL);
 | |
| 		outb(BCTL_BUSEN | BCTL_SEL, fd->base + REG_BCTL);
 | |
| 		outb(BIT(cmd->device->host->this_id) | BIT(scmd_id(cmd)),
 | |
| 		     fd->base + REG_SCSI_DATA_NOACK);
 | |
| 		/* Stop arbitration and enable parity */
 | |
| 		outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
 | |
| 		goto out;
 | |
| 	} else if (cmd->SCp.phase & in_selection) {
 | |
| 		status = inb(fd->base + REG_BSTAT);
 | |
| 		if (!(status & BSTAT_BSY)) {
 | |
| 			/* Try again, for slow devices */
 | |
| 			if (fdomain_select(cmd->device->host, scmd_id(cmd))) {
 | |
| 				set_host_byte(cmd, DID_NO_CONNECT);
 | |
| 				fdomain_finish_cmd(fd);
 | |
| 				goto out;
 | |
| 			}
 | |
| 			/* Stop arbitration and enable parity */
 | |
| 			outb(ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
 | |
| 		}
 | |
| 		cmd->SCp.phase = in_other;
 | |
| 		outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT, fd->base + REG_ICTL);
 | |
| 		outb(BCTL_BUSEN, fd->base + REG_BCTL);
 | |
| 		goto out;
 | |
| 	}
 | |
| 
 | |
| 	/* cur_cmd->SCp.phase == in_other: this is the body of the routine */
 | |
| 	status = inb(fd->base + REG_BSTAT);
 | |
| 
 | |
| 	if (status & BSTAT_REQ) {
 | |
| 		switch (status & (BSTAT_MSG | BSTAT_CMD | BSTAT_IO)) {
 | |
| 		case BSTAT_CMD:	/* COMMAND OUT */
 | |
| 			outb(cmd->cmnd[cmd->SCp.sent_command++],
 | |
| 			     fd->base + REG_SCSI_DATA);
 | |
| 			break;
 | |
| 		case 0:	/* DATA OUT -- tmc18c50/tmc18c30 only */
 | |
| 			if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) {
 | |
| 				cmd->SCp.have_data_in = -1;
 | |
| 				outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN |
 | |
| 				     PARITY_MASK, fd->base + REG_ACTL);
 | |
| 			}
 | |
| 			break;
 | |
| 		case BSTAT_IO:	/* DATA IN -- tmc18c50/tmc18c30 only */
 | |
| 			if (fd->chip != tmc1800 && !cmd->SCp.have_data_in) {
 | |
| 				cmd->SCp.have_data_in = 1;
 | |
| 				outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK,
 | |
| 				     fd->base + REG_ACTL);
 | |
| 			}
 | |
| 			break;
 | |
| 		case BSTAT_CMD | BSTAT_IO:	/* STATUS IN */
 | |
| 			cmd->SCp.Status = inb(fd->base + REG_SCSI_DATA);
 | |
| 			break;
 | |
| 		case BSTAT_MSG | BSTAT_CMD:	/* MESSAGE OUT */
 | |
| 			outb(MESSAGE_REJECT, fd->base + REG_SCSI_DATA);
 | |
| 			break;
 | |
| 		case BSTAT_MSG | BSTAT_CMD | BSTAT_IO:	/* MESSAGE IN */
 | |
| 			cmd->SCp.Message = inb(fd->base + REG_SCSI_DATA);
 | |
| 			if (cmd->SCp.Message == COMMAND_COMPLETE)
 | |
| 				++done;
 | |
| 			break;
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (fd->chip == tmc1800 && !cmd->SCp.have_data_in &&
 | |
| 	    cmd->SCp.sent_command >= cmd->cmd_len) {
 | |
| 		if (cmd->sc_data_direction == DMA_TO_DEVICE) {
 | |
| 			cmd->SCp.have_data_in = -1;
 | |
| 			outb(ACTL_IRQEN | ACTL_FIFOWR | ACTL_FIFOEN |
 | |
| 			     PARITY_MASK, fd->base + REG_ACTL);
 | |
| 		} else {
 | |
| 			cmd->SCp.have_data_in = 1;
 | |
| 			outb(ACTL_IRQEN | ACTL_FIFOEN | PARITY_MASK,
 | |
| 			     fd->base + REG_ACTL);
 | |
| 		}
 | |
| 	}
 | |
| 
 | |
| 	if (cmd->SCp.have_data_in == -1) /* DATA OUT */
 | |
| 		fdomain_write_data(cmd);
 | |
| 
 | |
| 	if (cmd->SCp.have_data_in == 1) /* DATA IN */
 | |
| 		fdomain_read_data(cmd);
 | |
| 
 | |
| 	if (done) {
 | |
| 		set_status_byte(cmd, cmd->SCp.Status);
 | |
| 		set_host_byte(cmd, DID_OK);
 | |
| 		scsi_msg_to_host_byte(cmd, cmd->SCp.Message);
 | |
| 		fdomain_finish_cmd(fd);
 | |
| 	} else {
 | |
| 		if (cmd->SCp.phase & disconnect) {
 | |
| 			outb(ICTL_FIFO | ICTL_SEL | ICTL_REQ | FIFO_COUNT,
 | |
| 			     fd->base + REG_ICTL);
 | |
| 			outb(0, fd->base + REG_BCTL);
 | |
| 		} else
 | |
| 			outb(ICTL_FIFO | ICTL_REQ | FIFO_COUNT,
 | |
| 			     fd->base + REG_ICTL);
 | |
| 	}
 | |
| out:
 | |
| 	spin_unlock_irqrestore(sh->host_lock, flags);
 | |
| }
 | |
| 
 | |
| static irqreturn_t fdomain_irq(int irq, void *dev_id)
 | |
| {
 | |
| 	struct fdomain *fd = dev_id;
 | |
| 
 | |
| 	/* Is it our IRQ? */
 | |
| 	if ((inb(fd->base + REG_ASTAT) & ASTAT_IRQ) == 0)
 | |
| 		return IRQ_NONE;
 | |
| 
 | |
| 	outb(0, fd->base + REG_ICTL);
 | |
| 
 | |
| 	/* We usually have one spurious interrupt after each command. */
 | |
| 	if (!fd->cur_cmd)	/* Spurious interrupt */
 | |
| 		return IRQ_NONE;
 | |
| 
 | |
| 	schedule_work(&fd->work);
 | |
| 
 | |
| 	return IRQ_HANDLED;
 | |
| }
 | |
| 
 | |
| static int fdomain_queue(struct Scsi_Host *sh, struct scsi_cmnd *cmd)
 | |
| {
 | |
| 	struct fdomain *fd = shost_priv(cmd->device->host);
 | |
| 	unsigned long flags;
 | |
| 
 | |
| 	cmd->SCp.Status		= 0;
 | |
| 	cmd->SCp.Message	= 0;
 | |
| 	cmd->SCp.have_data_in	= 0;
 | |
| 	cmd->SCp.sent_command	= 0;
 | |
| 	cmd->SCp.phase		= in_arbitration;
 | |
| 	scsi_set_resid(cmd, scsi_bufflen(cmd));
 | |
| 
 | |
| 	spin_lock_irqsave(sh->host_lock, flags);
 | |
| 
 | |
| 	fd->cur_cmd = cmd;
 | |
| 
 | |
| 	fdomain_make_bus_idle(fd);
 | |
| 
 | |
| 	/* Start arbitration */
 | |
| 	outb(0, fd->base + REG_ICTL);
 | |
| 	outb(0, fd->base + REG_BCTL);	/* Disable data drivers */
 | |
| 	/* Set our id bit */
 | |
| 	outb(BIT(cmd->device->host->this_id), fd->base + REG_SCSI_DATA_NOACK);
 | |
| 	outb(ICTL_ARB, fd->base + REG_ICTL);
 | |
| 	/* Start arbitration */
 | |
| 	outb(ACTL_ARB | ACTL_IRQEN | PARITY_MASK, fd->base + REG_ACTL);
 | |
| 
 | |
| 	spin_unlock_irqrestore(sh->host_lock, flags);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static int fdomain_abort(struct scsi_cmnd *cmd)
 | |
| {
 | |
| 	struct Scsi_Host *sh = cmd->device->host;
 | |
| 	struct fdomain *fd = shost_priv(sh);
 | |
| 	unsigned long flags;
 | |
| 
 | |
| 	if (!fd->cur_cmd)
 | |
| 		return FAILED;
 | |
| 
 | |
| 	spin_lock_irqsave(sh->host_lock, flags);
 | |
| 
 | |
| 	fdomain_make_bus_idle(fd);
 | |
| 	fd->cur_cmd->SCp.phase |= aborted;
 | |
| 
 | |
| 	/* Aborts are not done well. . . */
 | |
| 	set_host_byte(fd->cur_cmd, DID_ABORT);
 | |
| 	fdomain_finish_cmd(fd);
 | |
| 	spin_unlock_irqrestore(sh->host_lock, flags);
 | |
| 	return SUCCESS;
 | |
| }
 | |
| 
 | |
| static int fdomain_host_reset(struct scsi_cmnd *cmd)
 | |
| {
 | |
| 	struct Scsi_Host *sh = cmd->device->host;
 | |
| 	struct fdomain *fd = shost_priv(sh);
 | |
| 	unsigned long flags;
 | |
| 
 | |
| 	spin_lock_irqsave(sh->host_lock, flags);
 | |
| 	fdomain_reset(fd->base);
 | |
| 	spin_unlock_irqrestore(sh->host_lock, flags);
 | |
| 	return SUCCESS;
 | |
| }
 | |
| 
 | |
| static int fdomain_biosparam(struct scsi_device *sdev,
 | |
| 			     struct block_device *bdev,	sector_t capacity,
 | |
| 			     int geom[])
 | |
| {
 | |
| 	unsigned char *p = scsi_bios_ptable(bdev);
 | |
| 
 | |
| 	if (p && p[65] == 0xaa && p[64] == 0x55 /* Partition table valid */
 | |
| 	    && p[4]) {	 /* Partition type */
 | |
| 		geom[0] = p[5] + 1;	/* heads */
 | |
| 		geom[1] = p[6] & 0x3f;	/* sectors */
 | |
| 	} else {
 | |
| 		if (capacity >= 0x7e0000) {
 | |
| 			geom[0] = 255;	/* heads */
 | |
| 			geom[1] = 63;	/* sectors */
 | |
| 		} else if (capacity >= 0x200000) {
 | |
| 			geom[0] = 128;	/* heads */
 | |
| 			geom[1] = 63;	/* sectors */
 | |
| 		} else {
 | |
| 			geom[0] = 64;	/* heads */
 | |
| 			geom[1] = 32;	/* sectors */
 | |
| 		}
 | |
| 	}
 | |
| 	geom[2] = sector_div(capacity, geom[0] * geom[1]);
 | |
| 	kfree(p);
 | |
| 
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static struct scsi_host_template fdomain_template = {
 | |
| 	.module			= THIS_MODULE,
 | |
| 	.name			= "Future Domain TMC-16x0",
 | |
| 	.proc_name		= "fdomain",
 | |
| 	.queuecommand		= fdomain_queue,
 | |
| 	.eh_abort_handler	= fdomain_abort,
 | |
| 	.eh_host_reset_handler	= fdomain_host_reset,
 | |
| 	.bios_param		= fdomain_biosparam,
 | |
| 	.can_queue		= 1,
 | |
| 	.this_id		= 7,
 | |
| 	.sg_tablesize		= 64,
 | |
| 	.dma_boundary		= PAGE_SIZE - 1,
 | |
| };
 | |
| 
 | |
| struct Scsi_Host *fdomain_create(int base, int irq, int this_id,
 | |
| 				 struct device *dev)
 | |
| {
 | |
| 	struct Scsi_Host *sh;
 | |
| 	struct fdomain *fd;
 | |
| 	enum chip_type chip;
 | |
| 	static const char * const chip_names[] = {
 | |
| 		"Unknown", "TMC-1800", "TMC-18C50", "TMC-18C30"
 | |
| 	};
 | |
| 	unsigned long irq_flags = 0;
 | |
| 
 | |
| 	chip = fdomain_identify(base);
 | |
| 	if (!chip)
 | |
| 		return NULL;
 | |
| 
 | |
| 	fdomain_reset(base);
 | |
| 
 | |
| 	if (fdomain_test_loopback(base))
 | |
| 		return NULL;
 | |
| 
 | |
| 	if (!irq) {
 | |
| 		dev_err(dev, "card has no IRQ assigned");
 | |
| 		return NULL;
 | |
| 	}
 | |
| 
 | |
| 	sh = scsi_host_alloc(&fdomain_template, sizeof(struct fdomain));
 | |
| 	if (!sh)
 | |
| 		return NULL;
 | |
| 
 | |
| 	if (this_id)
 | |
| 		sh->this_id = this_id & 0x07;
 | |
| 
 | |
| 	sh->irq = irq;
 | |
| 	sh->io_port = base;
 | |
| 	sh->n_io_port = FDOMAIN_REGION_SIZE;
 | |
| 
 | |
| 	fd = shost_priv(sh);
 | |
| 	fd->base = base;
 | |
| 	fd->chip = chip;
 | |
| 	INIT_WORK(&fd->work, fdomain_work);
 | |
| 
 | |
| 	if (dev_is_pci(dev) || !strcmp(dev->bus->name, "pcmcia"))
 | |
| 		irq_flags = IRQF_SHARED;
 | |
| 
 | |
| 	if (request_irq(irq, fdomain_irq, irq_flags, "fdomain", fd))
 | |
| 		goto fail_put;
 | |
| 
 | |
| 	shost_printk(KERN_INFO, sh, "%s chip at 0x%x irq %d SCSI ID %d\n",
 | |
| 		     dev_is_pci(dev) ? "TMC-36C70 (PCI bus)" : chip_names[chip],
 | |
| 		     base, irq, sh->this_id);
 | |
| 
 | |
| 	if (scsi_add_host(sh, dev))
 | |
| 		goto fail_free_irq;
 | |
| 
 | |
| 	scsi_scan_host(sh);
 | |
| 
 | |
| 	return sh;
 | |
| 
 | |
| fail_free_irq:
 | |
| 	free_irq(irq, fd);
 | |
| fail_put:
 | |
| 	scsi_host_put(sh);
 | |
| 	return NULL;
 | |
| }
 | |
| EXPORT_SYMBOL_GPL(fdomain_create);
 | |
| 
 | |
| int fdomain_destroy(struct Scsi_Host *sh)
 | |
| {
 | |
| 	struct fdomain *fd = shost_priv(sh);
 | |
| 
 | |
| 	cancel_work_sync(&fd->work);
 | |
| 	scsi_remove_host(sh);
 | |
| 	if (sh->irq)
 | |
| 		free_irq(sh->irq, fd);
 | |
| 	scsi_host_put(sh);
 | |
| 	return 0;
 | |
| }
 | |
| EXPORT_SYMBOL_GPL(fdomain_destroy);
 | |
| 
 | |
| #ifdef CONFIG_PM_SLEEP
 | |
| static int fdomain_resume(struct device *dev)
 | |
| {
 | |
| 	struct fdomain *fd = shost_priv(dev_get_drvdata(dev));
 | |
| 
 | |
| 	fdomain_reset(fd->base);
 | |
| 	return 0;
 | |
| }
 | |
| 
 | |
| static SIMPLE_DEV_PM_OPS(fdomain_pm_ops, NULL, fdomain_resume);
 | |
| #endif /* CONFIG_PM_SLEEP */
 | |
| 
 | |
| MODULE_AUTHOR("Ondrej Zary, Rickard E. Faith");
 | |
| MODULE_DESCRIPTION("Future Domain TMC-16x0/TMC-3260 SCSI driver");
 | |
| MODULE_LICENSE("GPL");
 |