linux/drivers/pwm/pwm-mc33xs2410.c

// SPDX-License-Identifier: GPL-2.0
/*
 * Copyright (C) 2024 Liebherr-Electronics and Drives GmbH
 *
 * Reference Manual : https://www.nxp.com/docs/en/data-sheet/MC33XS2410.pdf
 *
 * Limitations:
 * - Supports frequencies between 0.5Hz and 2048Hz with following steps:
 *   - 0.5 Hz steps from 0.5 Hz to 32 Hz
 *   - 2 Hz steps from 2 Hz to 128 Hz
 *   - 8 Hz steps from 8 Hz to 512 Hz
 *   - 32 Hz steps from 32 Hz to 2048 Hz
 * - Cannot generate a 0 % duty cycle.
 * - Always produces low output if disabled.
 * - Configuration isn't atomic. When changing polarity, duty cycle or period
 *   the data is taken immediately, counters not being affected, resulting in a
 *   behavior of the output pin that is neither the old nor the new state,
 *   rather something in between.
 */
#define DEFAULT_SYMBOL_NAMESPACE		"PWM_MC33XS2410"

#include <linux/auxiliary_bus.h>
#include <linux/bitfield.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/math64.h>
#include <linux/mc33xs2410.h>
#include <linux/minmax.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/pwm.h>

#include <linux/spi/spi.h>

#define MC33XS2410_GLB_CTRL			0x00
#define MC33XS2410_GLB_CTRL_MODE		GENMASK(7, 6)
#define MC33XS2410_GLB_CTRL_MODE_NORMAL		FIELD_PREP(MC33XS2410_GLB_CTRL_MODE, 1)

#define MC33XS2410_PWM_CTRL1			0x05
/* chan in { 1 ... 4 } */
#define MC33XS2410_PWM_CTRL1_POL_INV(chan)	BIT((chan) + 1)

#define MC33XS2410_PWM_CTRL3			0x07
/* chan in { 1 ... 4 } */
#define MC33XS2410_PWM_CTRL3_EN(chan)		BIT(4 + (chan) - 1)

/* chan in { 1 ... 4 } */
#define MC33XS2410_PWM_FREQ(chan)		(0x08 + (chan) - 1)
#define MC33XS2410_PWM_FREQ_STEP		GENMASK(7, 6)
#define MC33XS2410_PWM_FREQ_COUNT		GENMASK(5, 0)

/* chan in { 1 ... 4 } */
#define MC33XS2410_PWM_DC(chan)			(0x0c + (chan) - 1)

#define MC33XS2410_WDT				0x14

#define MC33XS2410_PWM_MIN_PERIOD		488282
/* step in { 0 ... 3 } */
#define MC33XS2410_PWM_MAX_PERIOD(step)		(2000000000 >> (2 * (step)))

#define MC33XS2410_FRAME_IN_ADDR		GENMASK(15, 8)
#define MC33XS2410_FRAME_IN_DATA		GENMASK(7, 0)
#define MC33XS2410_FRAME_IN_ADDR_WR		BIT(7)
#define MC33XS2410_FRAME_IN_DATA_RD		BIT(7)
#define MC33XS2410_FRAME_OUT_DATA		GENMASK(13, 0)

#define MC33XS2410_MAX_TRANSFERS		5

static int mc33xs2410_write_regs(struct spi_device *spi, u8 *reg, u8 *val,
				 unsigned int len)
{
	u16 tx[MC33XS2410_MAX_TRANSFERS];
	int i;

	if (len > MC33XS2410_MAX_TRANSFERS)
		return -EINVAL;

	for (i = 0; i < len; i++)
		tx[i] = FIELD_PREP(MC33XS2410_FRAME_IN_DATA, val[i]) |
			FIELD_PREP(MC33XS2410_FRAME_IN_ADDR,
				   MC33XS2410_FRAME_IN_ADDR_WR | reg[i]);

	return spi_write(spi, tx, len * 2);
}

static int mc33xs2410_read_regs(struct spi_device *spi, u8 *reg, u8 flag,
				u16 *val, unsigned int len)
{
	u16 tx[MC33XS2410_MAX_TRANSFERS];
	u16 rx[MC33XS2410_MAX_TRANSFERS];
	struct spi_transfer t = {
		.tx_buf = tx,
		.rx_buf = rx,
	};
	int i, ret;

	len++;
	if (len > MC33XS2410_MAX_TRANSFERS)
		return -EINVAL;

	t.len = len * 2;
	for (i = 0; i < len - 1; i++)
		tx[i] = FIELD_PREP(MC33XS2410_FRAME_IN_DATA, flag) |
			FIELD_PREP(MC33XS2410_FRAME_IN_ADDR, reg[i]);

	ret = spi_sync_transfer(spi, &t, 1);
	if (ret < 0)
		return ret;

	for (i = 1; i < len; i++)
		val[i - 1] = FIELD_GET(MC33XS2410_FRAME_OUT_DATA, rx[i]);

	return 0;
}

static int mc33xs2410_write_reg(struct spi_device *spi, u8 reg, u8 val)
{
	return mc33xs2410_write_regs(spi, &reg, &val, 1);
}

static int mc33xs2410_read_reg(struct spi_device *spi, u8 reg, u16 *val, u8 flag)
{
	return mc33xs2410_read_regs(spi, &reg, flag, val, 1);
}

int mc33xs2410_read_reg_ctrl(struct spi_device *spi, u8 reg, u16 *val)
{
	return mc33xs2410_read_reg(spi, reg, val, MC33XS2410_FRAME_IN_DATA_RD);
}
EXPORT_SYMBOL_GPL(mc33xs2410_read_reg_ctrl);

int mc33xs2410_read_reg_diag(struct spi_device *spi, u8 reg, u16 *val)
{
	return mc33xs2410_read_reg(spi, reg, val, 0);
}
EXPORT_SYMBOL_GPL(mc33xs2410_read_reg_diag);

int mc33xs2410_modify_reg(struct spi_device *spi, u8 reg, u8 mask, u8 val)
{
	u16 tmp;
	int ret;

	ret = mc33xs2410_read_reg_ctrl(spi, reg, &tmp);
	if (ret < 0)
		return ret;

	tmp &= ~mask;
	tmp |= val & mask;

	return mc33xs2410_write_reg(spi, reg, tmp);
}
EXPORT_SYMBOL_GPL(mc33xs2410_modify_reg);

static u8 mc33xs2410_pwm_get_freq(u64 period)
{
	u8 step, count;

	/*
	 * Check which step [0 .. 3] is appropriate for the given period. The
	 * period ranges for the different step values overlap. Prefer big step
	 * values as these allow more finegrained period and duty cycle
	 * selection.
	 */

	switch (period) {
	case MC33XS2410_PWM_MIN_PERIOD ... MC33XS2410_PWM_MAX_PERIOD(3):
		step = 3;
		break;
	case MC33XS2410_PWM_MAX_PERIOD(3) + 1 ... MC33XS2410_PWM_MAX_PERIOD(2):
		step = 2;
		break;
	case MC33XS2410_PWM_MAX_PERIOD(2) + 1 ... MC33XS2410_PWM_MAX_PERIOD(1):
		step = 1;
		break;
	case MC33XS2410_PWM_MAX_PERIOD(1) + 1 ... MC33XS2410_PWM_MAX_PERIOD(0):
		step = 0;
		break;
	}

	/*
	 * Round up here because a higher count results in a higher frequency
	 * and so a smaller period.
	 */
	count = DIV_ROUND_UP((u32)MC33XS2410_PWM_MAX_PERIOD(step), (u32)period);
	return FIELD_PREP(MC33XS2410_PWM_FREQ_STEP, step) |
	       FIELD_PREP(MC33XS2410_PWM_FREQ_COUNT, count - 1);
}

static u64 mc33xs2410_pwm_get_period(u8 reg)
{
	u32 doubled_freq, code, doubled_steps;

	/*
	 * steps:
	 *   - 0 = 0.5Hz
	 *   - 1 = 2Hz
	 *   - 2 = 8Hz
	 *   - 3 = 32Hz
	 * frequency = (code + 1) x steps.
	 *
	 * To avoid losing precision in case steps value is zero, scale the
	 * steps value for now by two and keep it in mind when calculating the
	 * period that the frequency had been doubled.
	 */
	doubled_steps = 1 << (FIELD_GET(MC33XS2410_PWM_FREQ_STEP, reg) * 2);
	code = FIELD_GET(MC33XS2410_PWM_FREQ_COUNT, reg);
	doubled_freq = (code + 1) * doubled_steps;

	/* Convert frequency to period, considering the doubled frequency. */
	return DIV_ROUND_UP(2 * NSEC_PER_SEC, doubled_freq);
}

/*
 * The hardware cannot generate a 0% relative duty cycle for normal and inversed
 * polarity. For normal polarity, the channel must be disabled, the device then
 * emits a constant low signal.
 * For inverted polarity, the channel must be enabled, the polarity must be set
 * to normal and the relative duty cylce must be set to 100%. The device then
 * emits a constant high signal.
 */
static int mc33xs2410_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
				const struct pwm_state *state)
{
	struct spi_device *spi = pwmchip_get_drvdata(chip);
	u8 reg[4] = {
			MC33XS2410_PWM_FREQ(pwm->hwpwm + 1),
			MC33XS2410_PWM_DC(pwm->hwpwm + 1),
			MC33XS2410_PWM_CTRL1,
			MC33XS2410_PWM_CTRL3
		    };
	u64 period, duty_cycle;
	int ret, rel_dc;
	u16 rd_val[2];
	u8 wr_val[4];
	u8 mask;

	period = min(state->period, MC33XS2410_PWM_MAX_PERIOD(0));
	if (period < MC33XS2410_PWM_MIN_PERIOD)
		return -EINVAL;

	ret = mc33xs2410_read_regs(spi, &reg[2], MC33XS2410_FRAME_IN_DATA_RD, rd_val, 2);
	if (ret < 0)
		return ret;

	/* Frequency */
	wr_val[0] = mc33xs2410_pwm_get_freq(period);
	/* Continue calculations with the possibly truncated period */
	period = mc33xs2410_pwm_get_period(wr_val[0]);

	/* Duty cycle */
	duty_cycle = min(period, state->duty_cycle);
	rel_dc = div64_u64(duty_cycle * 256, period) - 1;
	if (rel_dc >= 0)
		wr_val[1] = rel_dc;
	else if (state->polarity == PWM_POLARITY_NORMAL)
		wr_val[1] = 0;
	else
		wr_val[1] = 255;

	/* Polarity */
	mask = MC33XS2410_PWM_CTRL1_POL_INV(pwm->hwpwm + 1);
	if (state->polarity == PWM_POLARITY_INVERSED && rel_dc >= 0)
		wr_val[2] = rd_val[0] | mask;
	else
		wr_val[2] = rd_val[0] & ~mask;

	/* Enable */
	mask = MC33XS2410_PWM_CTRL3_EN(pwm->hwpwm + 1);
	if (state->enabled &&
	    !(state->polarity == PWM_POLARITY_NORMAL && rel_dc < 0))
		wr_val[3] = rd_val[1] | mask;
	else
		wr_val[3] = rd_val[1] & ~mask;

	return mc33xs2410_write_regs(spi, reg, wr_val, 4);
}

static int mc33xs2410_pwm_get_state(struct pwm_chip *chip,
				    struct pwm_device *pwm,
				    struct pwm_state *state)
{
	struct spi_device *spi = pwmchip_get_drvdata(chip);
	u8 reg[4] = {
			MC33XS2410_PWM_FREQ(pwm->hwpwm + 1),
			MC33XS2410_PWM_DC(pwm->hwpwm + 1),
			MC33XS2410_PWM_CTRL1,
			MC33XS2410_PWM_CTRL3,
		    };
	u16 val[4];
	int ret;

	ret = mc33xs2410_read_regs(spi, reg, MC33XS2410_FRAME_IN_DATA_RD, val,
				   ARRAY_SIZE(reg));
	if (ret < 0)
		return ret;

	state->period = mc33xs2410_pwm_get_period(val[0]);
	state->polarity = (val[2] & MC33XS2410_PWM_CTRL1_POL_INV(pwm->hwpwm + 1)) ?
			  PWM_POLARITY_INVERSED : PWM_POLARITY_NORMAL;
	state->enabled = !!(val[3] & MC33XS2410_PWM_CTRL3_EN(pwm->hwpwm + 1));
	state->duty_cycle = DIV_ROUND_UP_ULL((val[1] + 1) * state->period, 256);

	return 0;
}

static const struct pwm_ops mc33xs2410_pwm_ops = {
	.apply = mc33xs2410_pwm_apply,
	.get_state = mc33xs2410_pwm_get_state,
};

static int mc33xs2410_reset(struct device *dev)
{
	struct gpio_desc *reset_gpio;

	reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
	if (IS_ERR_OR_NULL(reset_gpio))
		return PTR_ERR_OR_ZERO(reset_gpio);

	/* Wake-up time */
	fsleep(10000);

	return 0;
}

static int mc33xs2410_probe(struct spi_device *spi)
{
	struct device *dev = &spi->dev;
	struct auxiliary_device *adev;
	struct pwm_chip *chip;
	int ret;

	chip = devm_pwmchip_alloc(dev, 4, 0);
	if (IS_ERR(chip))
		return PTR_ERR(chip);

	spi->bits_per_word = 16;
	spi->mode |= SPI_CS_WORD;
	ret = spi_setup(spi);
	if (ret < 0)
		return ret;

	pwmchip_set_drvdata(chip, spi);
	chip->ops = &mc33xs2410_pwm_ops;

	/*
	 * Deasserts the reset of the device. Shouldn't change the output signal
	 * if the device was setup prior to probing.
	 */
	ret = mc33xs2410_reset(dev);
	if (ret)
		return ret;

	/*
	 * Disable watchdog and keep in mind that the watchdog won't trigger a
	 * reset of the machine when running into an timeout, instead the
	 * control over the outputs is handed over to the INx input logic
	 * signals of the device. Disabling it here just deactivates this
	 * feature until a proper solution is found.
	 */
	ret = mc33xs2410_write_reg(spi, MC33XS2410_WDT, 0x0);
	if (ret < 0)
		return dev_err_probe(dev, ret, "Failed to disable watchdog\n");

	/* Transition to normal mode */
	ret = mc33xs2410_modify_reg(spi, MC33XS2410_GLB_CTRL,
				    MC33XS2410_GLB_CTRL_MODE,
				    MC33XS2410_GLB_CTRL_MODE_NORMAL);
	if (ret < 0)
		return dev_err_probe(dev, ret,
				     "Failed to transition to normal mode\n");

	ret = devm_pwmchip_add(dev, chip);
	if (ret < 0)
		return dev_err_probe(dev, ret, "Failed to add pwm chip\n");

	adev = devm_auxiliary_device_create(dev, "hwmon", NULL);
	if (!adev)
		return dev_err_probe(dev, -ENODEV, "Failed to register hwmon device\n");

	return 0;
}

static const struct spi_device_id mc33xs2410_spi_id[] = {
	{ "mc33xs2410" },
	{ }
};
MODULE_DEVICE_TABLE(spi, mc33xs2410_spi_id);

static const struct of_device_id mc33xs2410_of_match[] = {
	{ .compatible = "nxp,mc33xs2410" },
	{ }
};
MODULE_DEVICE_TABLE(of, mc33xs2410_of_match);

static struct spi_driver mc33xs2410_driver = {
	.driver = {
		.name = "mc33xs2410-pwm",
		.of_match_table = mc33xs2410_of_match,
	},
	.probe = mc33xs2410_probe,
	.id_table = mc33xs2410_spi_id,
};
module_spi_driver(mc33xs2410_driver);

MODULE_DESCRIPTION("NXP MC33XS2410 high-side switch driver");
MODULE_AUTHOR("Dimitri Fedrau <dimitri.fedrau@liebherr.com>");
MODULE_LICENSE("GPL");