mirror of
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2025-08-05 16:54:27 +00:00

The firmware raises an alive interrupt upon sending the HCI_RESET or
BTINTEL_HCI_OP_RESET command. As part of handling the reset command,
firmware initializes the hardware and data path and raises the alive
interrupt. Upon receiving the alive interrupt, the driver must enable
the data path and grant RX buffers to the firmware before sending any
commands.
The alive context maintained in the driver must be updated before
sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race
condition where the context is also updated in the threaded IRQ.
The issue was observed in a stress reboot usecase (1/25) using "sudo
reboot" command where the firmware download was failing as the driver
was not granting RX buffer to firmware due to race condition.
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
Bluetooth: hci0: Boot Address: 0xb0301000
Bluetooth: hci0: Firmware Version: 167-12.25
Bluetooth: hci0: Waiting for firmware download to complete
Bluetooth: hci0: Firmware loaded in 99902 usecs
Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003
new_boot_stage: 0xa0db0003
Bluetooth: hci0: sent cmd: 0xfc01 alive context changed:
fw_dl -> intel_reset1
Bluetooth: hci0: Waiting for device to boot
Bluetooth: hci0: Device boot timeout
Bluetooth: hci0: Firmware download retry count: 1
Fixes: 05c200c8f0
("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
2603 lines
70 KiB
C
2603 lines
70 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
*
|
|
* Bluetooth support for Intel PCIe devices
|
|
*
|
|
* Copyright (C) 2024 Intel Corporation
|
|
*/
|
|
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/firmware.h>
|
|
#include <linux/pci.h>
|
|
#include <linux/wait.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/interrupt.h>
|
|
|
|
#include <linux/unaligned.h>
|
|
|
|
#include <net/bluetooth/bluetooth.h>
|
|
#include <net/bluetooth/hci_core.h>
|
|
|
|
#include "btintel.h"
|
|
#include "btintel_pcie.h"
|
|
|
|
#define VERSION "0.1"
|
|
|
|
#define BTINTEL_PCI_DEVICE(dev, subdev) \
|
|
.vendor = PCI_VENDOR_ID_INTEL, \
|
|
.device = (dev), \
|
|
.subvendor = PCI_ANY_ID, \
|
|
.subdevice = (subdev), \
|
|
.driver_data = 0
|
|
|
|
#define POLL_INTERVAL_US 10
|
|
|
|
/* Intel Bluetooth PCIe device id table */
|
|
static const struct pci_device_id btintel_pcie_table[] = {
|
|
{ BTINTEL_PCI_DEVICE(0x4D76, PCI_ANY_ID) },
|
|
{ BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
|
|
{ BTINTEL_PCI_DEVICE(0xE476, PCI_ANY_ID) },
|
|
{ 0 }
|
|
};
|
|
MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
|
|
|
|
struct btintel_pcie_dev_recovery {
|
|
struct list_head list;
|
|
u8 count;
|
|
time64_t last_error;
|
|
char name[];
|
|
};
|
|
|
|
/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
|
|
#define BTINTEL_PCIE_HCI_TYPE_LEN 4
|
|
#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
|
|
#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
|
|
#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
|
|
#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
|
|
#define BTINTEL_PCIE_HCI_ISO_PKT 0x00000005
|
|
|
|
#define BTINTEL_PCIE_MAGIC_NUM 0xA5A5A5A5
|
|
|
|
#define BTINTEL_PCIE_BLZR_HWEXP_SIZE 1024
|
|
#define BTINTEL_PCIE_BLZR_HWEXP_DMP_ADDR 0xB00A7C00
|
|
|
|
#define BTINTEL_PCIE_SCP_HWEXP_SIZE 4096
|
|
#define BTINTEL_PCIE_SCP_HWEXP_DMP_ADDR 0xB030F800
|
|
|
|
#define BTINTEL_PCIE_MAGIC_NUM 0xA5A5A5A5
|
|
|
|
#define BTINTEL_PCIE_TRIGGER_REASON_USER_TRIGGER 0x17A2
|
|
#define BTINTEL_PCIE_TRIGGER_REASON_FW_ASSERT 0x1E61
|
|
|
|
#define BTINTEL_PCIE_RESET_WINDOW_SECS 5
|
|
#define BTINTEL_PCIE_FLR_MAX_RETRY 1
|
|
|
|
/* Alive interrupt context */
|
|
enum {
|
|
BTINTEL_PCIE_ROM,
|
|
BTINTEL_PCIE_FW_DL,
|
|
BTINTEL_PCIE_HCI_RESET,
|
|
BTINTEL_PCIE_INTEL_HCI_RESET1,
|
|
BTINTEL_PCIE_INTEL_HCI_RESET2,
|
|
BTINTEL_PCIE_D0,
|
|
BTINTEL_PCIE_D3
|
|
};
|
|
|
|
/* Structure for dbgc fragment buffer
|
|
* @buf_addr_lsb: LSB of the buffer's physical address
|
|
* @buf_addr_msb: MSB of the buffer's physical address
|
|
* @buf_size: Total size of the buffer
|
|
*/
|
|
struct btintel_pcie_dbgc_ctxt_buf {
|
|
u32 buf_addr_lsb;
|
|
u32 buf_addr_msb;
|
|
u32 buf_size;
|
|
};
|
|
|
|
/* Structure for dbgc fragment
|
|
* @magic_num: 0XA5A5A5A5
|
|
* @ver: For Driver-FW compatibility
|
|
* @total_size: Total size of the payload debug info
|
|
* @num_buf: Num of allocated debug bufs
|
|
* @bufs: All buffer's addresses and sizes
|
|
*/
|
|
struct btintel_pcie_dbgc_ctxt {
|
|
u32 magic_num;
|
|
u32 ver;
|
|
u32 total_size;
|
|
u32 num_buf;
|
|
struct btintel_pcie_dbgc_ctxt_buf bufs[BTINTEL_PCIE_DBGC_BUFFER_COUNT];
|
|
};
|
|
|
|
struct btintel_pcie_removal {
|
|
struct pci_dev *pdev;
|
|
struct work_struct work;
|
|
};
|
|
|
|
static LIST_HEAD(btintel_pcie_recovery_list);
|
|
static DEFINE_SPINLOCK(btintel_pcie_recovery_lock);
|
|
|
|
static inline char *btintel_pcie_alivectxt_state2str(u32 alive_intr_ctxt)
|
|
{
|
|
switch (alive_intr_ctxt) {
|
|
case BTINTEL_PCIE_ROM:
|
|
return "rom";
|
|
case BTINTEL_PCIE_FW_DL:
|
|
return "fw_dl";
|
|
case BTINTEL_PCIE_D0:
|
|
return "d0";
|
|
case BTINTEL_PCIE_D3:
|
|
return "d3";
|
|
case BTINTEL_PCIE_HCI_RESET:
|
|
return "hci_reset";
|
|
case BTINTEL_PCIE_INTEL_HCI_RESET1:
|
|
return "intel_reset1";
|
|
case BTINTEL_PCIE_INTEL_HCI_RESET2:
|
|
return "intel_reset2";
|
|
default:
|
|
return "unknown";
|
|
}
|
|
}
|
|
|
|
/* This function initializes the memory for DBGC buffers and formats the
|
|
* DBGC fragment which consists header info and DBGC buffer's LSB, MSB and
|
|
* size as the payload
|
|
*/
|
|
static int btintel_pcie_setup_dbgc(struct btintel_pcie_data *data)
|
|
{
|
|
struct btintel_pcie_dbgc_ctxt db_frag;
|
|
struct data_buf *buf;
|
|
int i;
|
|
|
|
data->dbgc.count = BTINTEL_PCIE_DBGC_BUFFER_COUNT;
|
|
data->dbgc.bufs = devm_kcalloc(&data->pdev->dev, data->dbgc.count,
|
|
sizeof(*buf), GFP_KERNEL);
|
|
if (!data->dbgc.bufs)
|
|
return -ENOMEM;
|
|
|
|
data->dbgc.buf_v_addr = dmam_alloc_coherent(&data->pdev->dev,
|
|
data->dbgc.count *
|
|
BTINTEL_PCIE_DBGC_BUFFER_SIZE,
|
|
&data->dbgc.buf_p_addr,
|
|
GFP_KERNEL | __GFP_NOWARN);
|
|
if (!data->dbgc.buf_v_addr)
|
|
return -ENOMEM;
|
|
|
|
data->dbgc.frag_v_addr = dmam_alloc_coherent(&data->pdev->dev,
|
|
sizeof(struct btintel_pcie_dbgc_ctxt),
|
|
&data->dbgc.frag_p_addr,
|
|
GFP_KERNEL | __GFP_NOWARN);
|
|
if (!data->dbgc.frag_v_addr)
|
|
return -ENOMEM;
|
|
|
|
data->dbgc.frag_size = sizeof(struct btintel_pcie_dbgc_ctxt);
|
|
|
|
db_frag.magic_num = BTINTEL_PCIE_MAGIC_NUM;
|
|
db_frag.ver = BTINTEL_PCIE_DBGC_FRAG_VERSION;
|
|
db_frag.total_size = BTINTEL_PCIE_DBGC_FRAG_PAYLOAD_SIZE;
|
|
db_frag.num_buf = BTINTEL_PCIE_DBGC_FRAG_BUFFER_COUNT;
|
|
|
|
for (i = 0; i < data->dbgc.count; i++) {
|
|
buf = &data->dbgc.bufs[i];
|
|
buf->data_p_addr = data->dbgc.buf_p_addr + i * BTINTEL_PCIE_DBGC_BUFFER_SIZE;
|
|
buf->data = data->dbgc.buf_v_addr + i * BTINTEL_PCIE_DBGC_BUFFER_SIZE;
|
|
db_frag.bufs[i].buf_addr_lsb = lower_32_bits(buf->data_p_addr);
|
|
db_frag.bufs[i].buf_addr_msb = upper_32_bits(buf->data_p_addr);
|
|
db_frag.bufs[i].buf_size = BTINTEL_PCIE_DBGC_BUFFER_SIZE;
|
|
}
|
|
|
|
memcpy(data->dbgc.frag_v_addr, &db_frag, sizeof(db_frag));
|
|
return 0;
|
|
}
|
|
|
|
static inline void ipc_print_ia_ring(struct hci_dev *hdev, struct ia *ia,
|
|
u16 queue_num)
|
|
{
|
|
bt_dev_dbg(hdev, "IA: %s: tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
|
|
queue_num == BTINTEL_PCIE_TXQ_NUM ? "TXQ" : "RXQ",
|
|
ia->tr_hia[queue_num], ia->tr_tia[queue_num],
|
|
ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
|
|
}
|
|
|
|
static inline void ipc_print_urbd1(struct hci_dev *hdev, struct urbd1 *urbd1,
|
|
u16 index)
|
|
{
|
|
bt_dev_dbg(hdev, "RXQ:urbd1(%u) frbd_tag:%u status: 0x%x fixed:0x%x",
|
|
index, urbd1->frbd_tag, urbd1->status, urbd1->fixed);
|
|
}
|
|
|
|
static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry *entry)
|
|
{
|
|
u8 queue = entry->entry;
|
|
struct msix_entry *entries = entry - queue;
|
|
|
|
return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
|
|
}
|
|
|
|
/* Set the doorbell for TXQ to notify the device that @index (actually index-1)
|
|
* of the TFD is updated and ready to transmit.
|
|
*/
|
|
static void btintel_pcie_set_tx_db(struct btintel_pcie_data *data, u16 index)
|
|
{
|
|
u32 val;
|
|
|
|
val = index;
|
|
val |= (BTINTEL_PCIE_TX_DB_VEC << 16);
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_HBUS_TARG_WRPTR, val);
|
|
}
|
|
|
|
/* Copy the data to next(@tfd_index) data buffer and update the TFD(transfer
|
|
* descriptor) with the data length and the DMA address of the data buffer.
|
|
*/
|
|
static void btintel_pcie_prepare_tx(struct txq *txq, u16 tfd_index,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct data_buf *buf;
|
|
struct tfd *tfd;
|
|
|
|
tfd = &txq->tfds[tfd_index];
|
|
memset(tfd, 0, sizeof(*tfd));
|
|
|
|
buf = &txq->bufs[tfd_index];
|
|
|
|
tfd->size = skb->len;
|
|
tfd->addr = buf->data_p_addr;
|
|
|
|
/* Copy the outgoing data to DMA buffer */
|
|
memcpy(buf->data, skb->data, tfd->size);
|
|
}
|
|
|
|
static inline void btintel_pcie_dump_debug_registers(struct hci_dev *hdev)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
u16 cr_hia, cr_tia;
|
|
u32 reg, mbox_reg;
|
|
struct sk_buff *skb;
|
|
u8 buf[80];
|
|
|
|
skb = alloc_skb(1024, GFP_ATOMIC);
|
|
if (!skb)
|
|
return;
|
|
|
|
snprintf(buf, sizeof(buf), "%s", "---- Dump of debug registers ---");
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_BOOT_STAGE_REG);
|
|
snprintf(buf, sizeof(buf), "boot stage: 0x%8.8x", reg);
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
data->boot_stage_cache = reg;
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_IPC_STATUS_REG);
|
|
snprintf(buf, sizeof(buf), "ipc status: 0x%8.8x", reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_IPC_CONTROL_REG);
|
|
snprintf(buf, sizeof(buf), "ipc control: 0x%8.8x", reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_IPC_SLEEP_CTL_REG);
|
|
snprintf(buf, sizeof(buf), "ipc sleep control: 0x%8.8x", reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
|
|
/*Read the Mail box status and registers*/
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_MBOX_STATUS_REG);
|
|
snprintf(buf, sizeof(buf), "mbox status: 0x%8.8x", reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
if (reg & BTINTEL_PCIE_CSR_MBOX_STATUS_MBOX1) {
|
|
mbox_reg = btintel_pcie_rd_reg32(data,
|
|
BTINTEL_PCIE_CSR_MBOX_1_REG);
|
|
snprintf(buf, sizeof(buf), "mbox_1: 0x%8.8x", mbox_reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
}
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_MBOX_STATUS_MBOX2) {
|
|
mbox_reg = btintel_pcie_rd_reg32(data,
|
|
BTINTEL_PCIE_CSR_MBOX_2_REG);
|
|
snprintf(buf, sizeof(buf), "mbox_2: 0x%8.8x", mbox_reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
}
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_MBOX_STATUS_MBOX3) {
|
|
mbox_reg = btintel_pcie_rd_reg32(data,
|
|
BTINTEL_PCIE_CSR_MBOX_3_REG);
|
|
snprintf(buf, sizeof(buf), "mbox_3: 0x%8.8x", mbox_reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
}
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_MBOX_STATUS_MBOX4) {
|
|
mbox_reg = btintel_pcie_rd_reg32(data,
|
|
BTINTEL_PCIE_CSR_MBOX_4_REG);
|
|
snprintf(buf, sizeof(buf), "mbox_4: 0x%8.8x", mbox_reg);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
}
|
|
|
|
cr_hia = data->ia.cr_hia[BTINTEL_PCIE_RXQ_NUM];
|
|
cr_tia = data->ia.cr_tia[BTINTEL_PCIE_RXQ_NUM];
|
|
snprintf(buf, sizeof(buf), "rxq: cr_tia: %u cr_hia: %u", cr_tia, cr_hia);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
|
|
cr_hia = data->ia.cr_hia[BTINTEL_PCIE_TXQ_NUM];
|
|
cr_tia = data->ia.cr_tia[BTINTEL_PCIE_TXQ_NUM];
|
|
snprintf(buf, sizeof(buf), "txq: cr_tia: %u cr_hia: %u", cr_tia, cr_hia);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
snprintf(buf, sizeof(buf), "--------------------------------");
|
|
bt_dev_dbg(hdev, "%s", buf);
|
|
|
|
hci_recv_diag(hdev, skb);
|
|
}
|
|
|
|
static int btintel_pcie_send_sync(struct btintel_pcie_data *data,
|
|
struct sk_buff *skb, u32 pkt_type, u16 opcode)
|
|
{
|
|
int ret;
|
|
u16 tfd_index;
|
|
u32 old_ctxt;
|
|
bool wait_on_alive = false;
|
|
struct hci_dev *hdev = data->hdev;
|
|
|
|
struct txq *txq = &data->txq;
|
|
|
|
tfd_index = data->ia.tr_hia[BTINTEL_PCIE_TXQ_NUM];
|
|
|
|
if (tfd_index > txq->count)
|
|
return -ERANGE;
|
|
|
|
/* Firmware raises alive interrupt on HCI_OP_RESET or
|
|
* BTINTEL_HCI_OP_RESET
|
|
*/
|
|
wait_on_alive = (pkt_type == BTINTEL_PCIE_HCI_CMD_PKT &&
|
|
(opcode == BTINTEL_HCI_OP_RESET || opcode == HCI_OP_RESET));
|
|
|
|
if (wait_on_alive) {
|
|
data->gp0_received = false;
|
|
old_ctxt = data->alive_intr_ctxt;
|
|
data->alive_intr_ctxt =
|
|
(opcode == BTINTEL_HCI_OP_RESET ? BTINTEL_PCIE_INTEL_HCI_RESET1 :
|
|
BTINTEL_PCIE_HCI_RESET);
|
|
bt_dev_dbg(data->hdev, "sending cmd: 0x%4.4x alive context changed: %s -> %s",
|
|
opcode, btintel_pcie_alivectxt_state2str(old_ctxt),
|
|
btintel_pcie_alivectxt_state2str(data->alive_intr_ctxt));
|
|
}
|
|
|
|
memcpy(skb_push(skb, BTINTEL_PCIE_HCI_TYPE_LEN), &pkt_type,
|
|
BTINTEL_PCIE_HCI_TYPE_LEN);
|
|
|
|
/* Prepare for TX. It updates the TFD with the length of data and
|
|
* address of the DMA buffer, and copy the data to the DMA buffer
|
|
*/
|
|
btintel_pcie_prepare_tx(txq, tfd_index, skb);
|
|
|
|
tfd_index = (tfd_index + 1) % txq->count;
|
|
data->ia.tr_hia[BTINTEL_PCIE_TXQ_NUM] = tfd_index;
|
|
|
|
/* Arm wait event condition */
|
|
data->tx_wait_done = false;
|
|
|
|
/* Set the doorbell to notify the device */
|
|
btintel_pcie_set_tx_db(data, tfd_index);
|
|
|
|
/* Wait for the complete interrupt - URBD0 */
|
|
ret = wait_event_timeout(data->tx_wait_q, data->tx_wait_done,
|
|
msecs_to_jiffies(BTINTEL_PCIE_TX_WAIT_TIMEOUT_MS));
|
|
if (!ret) {
|
|
bt_dev_err(data->hdev, "Timeout (%u ms) on tx completion",
|
|
BTINTEL_PCIE_TX_WAIT_TIMEOUT_MS);
|
|
btintel_pcie_dump_debug_registers(data->hdev);
|
|
return -ETIME;
|
|
}
|
|
|
|
if (wait_on_alive) {
|
|
ret = wait_event_timeout(data->gp0_wait_q,
|
|
data->gp0_received,
|
|
msecs_to_jiffies(BTINTEL_DEFAULT_INTR_TIMEOUT_MS));
|
|
if (!ret) {
|
|
hdev->stat.err_tx++;
|
|
bt_dev_err(hdev, "Timeout (%u ms) on alive interrupt, alive context: %s",
|
|
BTINTEL_DEFAULT_INTR_TIMEOUT_MS,
|
|
btintel_pcie_alivectxt_state2str(data->alive_intr_ctxt));
|
|
return -ETIME;
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* Set the doorbell for RXQ to notify the device that @index (actually index-1)
|
|
* is available to receive the data
|
|
*/
|
|
static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16 index)
|
|
{
|
|
u32 val;
|
|
|
|
val = index;
|
|
val |= (BTINTEL_PCIE_RX_DB_VEC << 16);
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_HBUS_TARG_WRPTR, val);
|
|
}
|
|
|
|
/* Update the FRBD (free buffer descriptor) with the @frbd_index and the
|
|
* DMA address of the free buffer.
|
|
*/
|
|
static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
|
|
{
|
|
struct data_buf *buf;
|
|
struct frbd *frbd;
|
|
|
|
/* Get the buffer of the FRBD for DMA */
|
|
buf = &rxq->bufs[frbd_index];
|
|
|
|
frbd = &rxq->frbds[frbd_index];
|
|
memset(frbd, 0, sizeof(*frbd));
|
|
|
|
/* Update FRBD */
|
|
frbd->tag = frbd_index;
|
|
frbd->addr = buf->data_p_addr;
|
|
}
|
|
|
|
static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
|
|
{
|
|
u16 frbd_index;
|
|
struct rxq *rxq = &data->rxq;
|
|
|
|
frbd_index = data->ia.tr_hia[BTINTEL_PCIE_RXQ_NUM];
|
|
|
|
if (frbd_index > rxq->count)
|
|
return -ERANGE;
|
|
|
|
/* Prepare for RX submit. It updates the FRBD with the address of DMA
|
|
* buffer
|
|
*/
|
|
btintel_pcie_prepare_rx(rxq, frbd_index);
|
|
|
|
frbd_index = (frbd_index + 1) % rxq->count;
|
|
data->ia.tr_hia[BTINTEL_PCIE_RXQ_NUM] = frbd_index;
|
|
ipc_print_ia_ring(data->hdev, &data->ia, BTINTEL_PCIE_RXQ_NUM);
|
|
|
|
/* Set the doorbell to notify the device */
|
|
btintel_pcie_set_rx_db(data, frbd_index);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
|
|
{
|
|
int i, ret;
|
|
struct rxq *rxq = &data->rxq;
|
|
|
|
/* Post (BTINTEL_PCIE_RX_DESCS_COUNT - 3) buffers to overcome the
|
|
* hardware issues leading to race condition at the firmware.
|
|
*/
|
|
|
|
for (i = 0; i < rxq->count - 3; i++) {
|
|
ret = btintel_pcie_submit_rx(data);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
|
|
{
|
|
memset(data->ia.tr_hia, 0, sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES);
|
|
memset(data->ia.tr_tia, 0, sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES);
|
|
memset(data->ia.cr_hia, 0, sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES);
|
|
memset(data->ia.cr_tia, 0, sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES);
|
|
}
|
|
|
|
static int btintel_pcie_reset_bt(struct btintel_pcie_data *data)
|
|
{
|
|
u32 reg;
|
|
int retry = 3;
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
|
|
reg &= ~(BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_ENA |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_INIT |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_INIT);
|
|
reg |= BTINTEL_PCIE_CSR_FUNC_CTRL_BUS_MASTER_DISCON;
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
|
|
do {
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
if (reg & BTINTEL_PCIE_CSR_FUNC_CTRL_BUS_MASTER_STS)
|
|
break;
|
|
usleep_range(10000, 12000);
|
|
|
|
} while (--retry > 0);
|
|
usleep_range(10000, 12000);
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
|
|
reg &= ~(BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_ENA |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_INIT |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_INIT);
|
|
reg |= BTINTEL_PCIE_CSR_FUNC_CTRL_SW_RESET;
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
usleep_range(10000, 12000);
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
bt_dev_dbg(data->hdev, "csr register after reset: 0x%8.8x", reg);
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_BOOT_STAGE_REG);
|
|
|
|
/* If shared hardware reset is success then boot stage register shall be
|
|
* set to 0
|
|
*/
|
|
return reg == 0 ? 0 : -ENODEV;
|
|
}
|
|
|
|
static void btintel_pcie_mac_init(struct btintel_pcie_data *data)
|
|
{
|
|
u32 reg;
|
|
|
|
/* Set MAC_INIT bit to start primary bootloader */
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
reg &= ~(BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_INIT |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_BUS_MASTER_DISCON |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_SW_RESET);
|
|
reg |= (BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_ENA |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_INIT);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
}
|
|
|
|
static int btintel_pcie_add_dmp_data(struct hci_dev *hdev, const void *data, int size)
|
|
{
|
|
struct sk_buff *skb;
|
|
int err;
|
|
|
|
skb = alloc_skb(size, GFP_ATOMIC);
|
|
if (!skb)
|
|
return -ENOMEM;
|
|
|
|
skb_put_data(skb, data, size);
|
|
err = hci_devcd_append(hdev, skb);
|
|
if (err) {
|
|
bt_dev_err(hdev, "Failed to append data in the coredump");
|
|
return err;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int btintel_pcie_get_mac_access(struct btintel_pcie_data *data)
|
|
{
|
|
u32 reg;
|
|
int retry = 15;
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
|
|
reg |= BTINTEL_PCIE_CSR_FUNC_CTRL_STOP_MAC_ACCESS_DIS;
|
|
reg |= BTINTEL_PCIE_CSR_FUNC_CTRL_XTAL_CLK_REQ;
|
|
if ((reg & BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_ACCESS_STS) == 0)
|
|
reg |= BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_ACCESS_REQ;
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
|
|
do {
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
if (reg & BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_ACCESS_STS)
|
|
return 0;
|
|
/* Need delay here for Target Access harwdware to settle down*/
|
|
usleep_range(1000, 1200);
|
|
|
|
} while (--retry > 0);
|
|
|
|
return -ETIME;
|
|
}
|
|
|
|
static void btintel_pcie_release_mac_access(struct btintel_pcie_data *data)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_ACCESS_REQ)
|
|
reg &= ~BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_ACCESS_REQ;
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_FUNC_CTRL_STOP_MAC_ACCESS_DIS)
|
|
reg &= ~BTINTEL_PCIE_CSR_FUNC_CTRL_STOP_MAC_ACCESS_DIS;
|
|
|
|
if (reg & BTINTEL_PCIE_CSR_FUNC_CTRL_XTAL_CLK_REQ)
|
|
reg &= ~BTINTEL_PCIE_CSR_FUNC_CTRL_XTAL_CLK_REQ;
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
}
|
|
|
|
static void btintel_pcie_copy_tlv(struct sk_buff *skb, enum btintel_pcie_tlv_type type,
|
|
void *data, int size)
|
|
{
|
|
struct intel_tlv *tlv;
|
|
|
|
tlv = skb_put(skb, sizeof(*tlv) + size);
|
|
tlv->type = type;
|
|
tlv->len = size;
|
|
memcpy(tlv->val, data, tlv->len);
|
|
}
|
|
|
|
static int btintel_pcie_read_dram_buffers(struct btintel_pcie_data *data)
|
|
{
|
|
u32 offset, prev_size, wr_ptr_status, dump_size, i;
|
|
struct btintel_pcie_dbgc *dbgc = &data->dbgc;
|
|
u8 buf_idx, dump_time_len, fw_build;
|
|
struct hci_dev *hdev = data->hdev;
|
|
struct intel_tlv *tlv;
|
|
struct timespec64 now;
|
|
struct sk_buff *skb;
|
|
struct tm tm_now;
|
|
char buf[256];
|
|
u16 hdr_len;
|
|
int ret;
|
|
|
|
wr_ptr_status = btintel_pcie_rd_dev_mem(data, BTINTEL_PCIE_DBGC_CUR_DBGBUFF_STATUS);
|
|
offset = wr_ptr_status & BTINTEL_PCIE_DBG_OFFSET_BIT_MASK;
|
|
|
|
buf_idx = BTINTEL_PCIE_DBGC_DBG_BUF_IDX(wr_ptr_status);
|
|
if (buf_idx > dbgc->count) {
|
|
bt_dev_warn(hdev, "Buffer index is invalid");
|
|
return -EINVAL;
|
|
}
|
|
|
|
prev_size = buf_idx * BTINTEL_PCIE_DBGC_BUFFER_SIZE;
|
|
if (prev_size + offset >= prev_size)
|
|
data->dmp_hdr.write_ptr = prev_size + offset;
|
|
else
|
|
return -EINVAL;
|
|
|
|
ktime_get_real_ts64(&now);
|
|
time64_to_tm(now.tv_sec, 0, &tm_now);
|
|
dump_time_len = snprintf(buf, sizeof(buf), "Dump Time: %02d-%02d-%04ld %02d:%02d:%02d",
|
|
tm_now.tm_mday, tm_now.tm_mon + 1, tm_now.tm_year + 1900,
|
|
tm_now.tm_hour, tm_now.tm_min, tm_now.tm_sec);
|
|
|
|
fw_build = snprintf(buf + dump_time_len, sizeof(buf) - dump_time_len,
|
|
"Firmware Timestamp: Year %u WW %02u buildtype %u build %u",
|
|
2000 + (data->dmp_hdr.fw_timestamp >> 8),
|
|
data->dmp_hdr.fw_timestamp & 0xff, data->dmp_hdr.fw_build_type,
|
|
data->dmp_hdr.fw_build_num);
|
|
|
|
hdr_len = sizeof(*tlv) + sizeof(data->dmp_hdr.cnvi_bt) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.write_ptr) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.wrap_ctr) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.trigger_reason) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.fw_git_sha1) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.cnvr_top) +
|
|
sizeof(*tlv) + sizeof(data->dmp_hdr.cnvi_top) +
|
|
sizeof(*tlv) + dump_time_len +
|
|
sizeof(*tlv) + fw_build;
|
|
|
|
dump_size = hdr_len + sizeof(hdr_len);
|
|
|
|
skb = alloc_skb(dump_size, GFP_KERNEL);
|
|
if (!skb)
|
|
return -ENOMEM;
|
|
|
|
/* Add debug buffers data length to dump size */
|
|
dump_size += BTINTEL_PCIE_DBGC_BUFFER_SIZE * dbgc->count;
|
|
|
|
ret = hci_devcd_init(hdev, dump_size);
|
|
if (ret) {
|
|
bt_dev_err(hdev, "Failed to init devcoredump, err %d", ret);
|
|
kfree_skb(skb);
|
|
return ret;
|
|
}
|
|
|
|
skb_put_data(skb, &hdr_len, sizeof(hdr_len));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_CNVI_BT, &data->dmp_hdr.cnvi_bt,
|
|
sizeof(data->dmp_hdr.cnvi_bt));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_WRITE_PTR, &data->dmp_hdr.write_ptr,
|
|
sizeof(data->dmp_hdr.write_ptr));
|
|
|
|
data->dmp_hdr.wrap_ctr = btintel_pcie_rd_dev_mem(data,
|
|
BTINTEL_PCIE_DBGC_DBGBUFF_WRAP_ARND);
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_WRAP_CTR, &data->dmp_hdr.wrap_ctr,
|
|
sizeof(data->dmp_hdr.wrap_ctr));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_TRIGGER_REASON, &data->dmp_hdr.trigger_reason,
|
|
sizeof(data->dmp_hdr.trigger_reason));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_FW_SHA, &data->dmp_hdr.fw_git_sha1,
|
|
sizeof(data->dmp_hdr.fw_git_sha1));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_CNVR_TOP, &data->dmp_hdr.cnvr_top,
|
|
sizeof(data->dmp_hdr.cnvr_top));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_CNVI_TOP, &data->dmp_hdr.cnvi_top,
|
|
sizeof(data->dmp_hdr.cnvi_top));
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_DUMP_TIME, buf, dump_time_len);
|
|
|
|
btintel_pcie_copy_tlv(skb, BTINTEL_FW_BUILD, buf + dump_time_len, fw_build);
|
|
|
|
ret = hci_devcd_append(hdev, skb);
|
|
if (ret)
|
|
goto exit_err;
|
|
|
|
for (i = 0; i < dbgc->count; i++) {
|
|
ret = btintel_pcie_add_dmp_data(hdev, dbgc->bufs[i].data,
|
|
BTINTEL_PCIE_DBGC_BUFFER_SIZE);
|
|
if (ret)
|
|
break;
|
|
}
|
|
|
|
exit_err:
|
|
hci_devcd_complete(hdev);
|
|
return ret;
|
|
}
|
|
|
|
static void btintel_pcie_dump_traces(struct hci_dev *hdev)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
int ret = 0;
|
|
|
|
ret = btintel_pcie_get_mac_access(data);
|
|
if (ret) {
|
|
bt_dev_err(hdev, "Failed to get mac access: (%d)", ret);
|
|
return;
|
|
}
|
|
|
|
ret = btintel_pcie_read_dram_buffers(data);
|
|
|
|
btintel_pcie_release_mac_access(data);
|
|
|
|
if (ret)
|
|
bt_dev_err(hdev, "Failed to dump traces: (%d)", ret);
|
|
}
|
|
|
|
static void btintel_pcie_dump_hdr(struct hci_dev *hdev, struct sk_buff *skb)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
u16 len = skb->len;
|
|
u16 *hdrlen_ptr;
|
|
char buf[80];
|
|
|
|
hdrlen_ptr = skb_put_zero(skb, sizeof(len));
|
|
|
|
snprintf(buf, sizeof(buf), "Controller Name: 0x%X\n",
|
|
INTEL_HW_VARIANT(data->dmp_hdr.cnvi_bt));
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
|
|
snprintf(buf, sizeof(buf), "Firmware Build Number: %u\n",
|
|
data->dmp_hdr.fw_build_num);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
|
|
snprintf(buf, sizeof(buf), "Driver: %s\n", data->dmp_hdr.driver_name);
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
|
|
snprintf(buf, sizeof(buf), "Vendor: Intel\n");
|
|
skb_put_data(skb, buf, strlen(buf));
|
|
|
|
*hdrlen_ptr = skb->len - len;
|
|
}
|
|
|
|
static void btintel_pcie_dump_notify(struct hci_dev *hdev, int state)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
|
|
switch (state) {
|
|
case HCI_DEVCOREDUMP_IDLE:
|
|
data->dmp_hdr.state = HCI_DEVCOREDUMP_IDLE;
|
|
break;
|
|
case HCI_DEVCOREDUMP_ACTIVE:
|
|
data->dmp_hdr.state = HCI_DEVCOREDUMP_ACTIVE;
|
|
break;
|
|
case HCI_DEVCOREDUMP_TIMEOUT:
|
|
case HCI_DEVCOREDUMP_ABORT:
|
|
case HCI_DEVCOREDUMP_DONE:
|
|
data->dmp_hdr.state = HCI_DEVCOREDUMP_IDLE;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/* This function enables BT function by setting BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_INIT bit in
|
|
* BTINTEL_PCIE_CSR_FUNC_CTRL_REG register and wait for MSI-X with
|
|
* BTINTEL_PCIE_MSIX_HW_INT_CAUSES_GP0.
|
|
* Then the host reads firmware version from BTINTEL_CSR_F2D_MBX and the boot stage
|
|
* from BTINTEL_PCIE_CSR_BOOT_STAGE_REG.
|
|
*/
|
|
static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
|
|
{
|
|
int err;
|
|
u32 reg;
|
|
|
|
data->gp0_received = false;
|
|
|
|
/* Update the DMA address of CI struct to CSR */
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_CI_ADDR_LSB_REG,
|
|
data->ci_p_addr & 0xffffffff);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_CI_ADDR_MSB_REG,
|
|
(u64)data->ci_p_addr >> 32);
|
|
|
|
/* Reset the cached value of boot stage. it is updated by the MSI-X
|
|
* gp0 interrupt handler.
|
|
*/
|
|
data->boot_stage_cache = 0x0;
|
|
|
|
/* Set MAC_INIT bit to start primary bootloader */
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
reg &= ~(BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_INIT |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_BUS_MASTER_DISCON |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_SW_RESET);
|
|
reg |= (BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_ENA |
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_MAC_INIT);
|
|
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG, reg);
|
|
|
|
/* MAC is ready. Enable BT FUNC */
|
|
btintel_pcie_set_reg_bits(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG,
|
|
BTINTEL_PCIE_CSR_FUNC_CTRL_FUNC_INIT);
|
|
|
|
btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_FUNC_CTRL_REG);
|
|
|
|
/* wait for interrupt from the device after booting up to primary
|
|
* bootloader.
|
|
*/
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_ROM;
|
|
err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
|
|
msecs_to_jiffies(BTINTEL_DEFAULT_INTR_TIMEOUT_MS));
|
|
if (!err)
|
|
return -ETIME;
|
|
|
|
/* Check cached boot stage is BTINTEL_PCIE_CSR_BOOT_STAGE_ROM(BIT(0)) */
|
|
if (~data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_ROM)
|
|
return -ENODEV;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_op(struct btintel_pcie_data *data)
|
|
{
|
|
return data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_OPFW;
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_iml(struct btintel_pcie_data *data)
|
|
{
|
|
return data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_IML &&
|
|
!(data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_OPFW);
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_d3(struct btintel_pcie_data *data)
|
|
{
|
|
return data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_D3_STATE_READY;
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_d0(struct btintel_pcie_data *data)
|
|
{
|
|
return !(data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_D3_STATE_READY);
|
|
}
|
|
|
|
static void btintel_pcie_wr_sleep_cntrl(struct btintel_pcie_data *data,
|
|
u32 dxstate)
|
|
{
|
|
bt_dev_dbg(data->hdev, "writing sleep_ctl_reg: 0x%8.8x", dxstate);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_IPC_SLEEP_CTL_REG, dxstate);
|
|
}
|
|
|
|
static int btintel_pcie_read_device_mem(struct btintel_pcie_data *data,
|
|
void *buf, u32 dev_addr, int len)
|
|
{
|
|
int err;
|
|
u32 *val = buf;
|
|
|
|
/* Get device mac access */
|
|
err = btintel_pcie_get_mac_access(data);
|
|
if (err) {
|
|
bt_dev_err(data->hdev, "Failed to get mac access %d", err);
|
|
return err;
|
|
}
|
|
|
|
for (; len > 0; len -= 4, dev_addr += 4, val++)
|
|
*val = btintel_pcie_rd_dev_mem(data, dev_addr);
|
|
|
|
btintel_pcie_release_mac_access(data);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_lockdown(struct btintel_pcie_data *data)
|
|
{
|
|
return (data->boot_stage_cache &
|
|
BTINTEL_PCIE_CSR_BOOT_STAGE_ROM_LOCKDOWN) ||
|
|
(data->boot_stage_cache &
|
|
BTINTEL_PCIE_CSR_BOOT_STAGE_IML_LOCKDOWN);
|
|
}
|
|
|
|
static inline bool btintel_pcie_in_error(struct btintel_pcie_data *data)
|
|
{
|
|
return (data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_DEVICE_ERR) ||
|
|
(data->boot_stage_cache & BTINTEL_PCIE_CSR_BOOT_STAGE_ABORT_HANDLER);
|
|
}
|
|
|
|
static void btintel_pcie_msix_gp1_handler(struct btintel_pcie_data *data)
|
|
{
|
|
bt_dev_err(data->hdev, "Received gp1 mailbox interrupt");
|
|
btintel_pcie_dump_debug_registers(data->hdev);
|
|
}
|
|
|
|
/* This function handles the MSI-X interrupt for gp0 cause (bit 0 in
|
|
* BTINTEL_PCIE_CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image response.
|
|
*/
|
|
static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
|
|
{
|
|
bool submit_rx, signal_waitq;
|
|
u32 reg, old_ctxt;
|
|
|
|
/* This interrupt is for three different causes and it is not easy to
|
|
* know what causes the interrupt. So, it compares each register value
|
|
* with cached value and update it before it wake up the queue.
|
|
*/
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_BOOT_STAGE_REG);
|
|
if (reg != data->boot_stage_cache)
|
|
data->boot_stage_cache = reg;
|
|
|
|
bt_dev_dbg(data->hdev, "Alive context: %s old_boot_stage: 0x%8.8x new_boot_stage: 0x%8.8x",
|
|
btintel_pcie_alivectxt_state2str(data->alive_intr_ctxt),
|
|
data->boot_stage_cache, reg);
|
|
reg = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_IMG_RESPONSE_REG);
|
|
if (reg != data->img_resp_cache)
|
|
data->img_resp_cache = reg;
|
|
|
|
if (btintel_pcie_in_error(data)) {
|
|
bt_dev_err(data->hdev, "Controller in error state");
|
|
btintel_pcie_dump_debug_registers(data->hdev);
|
|
return;
|
|
}
|
|
|
|
if (btintel_pcie_in_lockdown(data)) {
|
|
bt_dev_err(data->hdev, "Controller in lockdown state");
|
|
btintel_pcie_dump_debug_registers(data->hdev);
|
|
return;
|
|
}
|
|
|
|
data->gp0_received = true;
|
|
|
|
old_ctxt = data->alive_intr_ctxt;
|
|
submit_rx = false;
|
|
signal_waitq = false;
|
|
|
|
switch (data->alive_intr_ctxt) {
|
|
case BTINTEL_PCIE_ROM:
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_FW_DL;
|
|
signal_waitq = true;
|
|
break;
|
|
case BTINTEL_PCIE_FW_DL:
|
|
/* Error case is already handled. Ideally control shall not
|
|
* reach here
|
|
*/
|
|
break;
|
|
case BTINTEL_PCIE_INTEL_HCI_RESET1:
|
|
if (btintel_pcie_in_op(data)) {
|
|
submit_rx = true;
|
|
signal_waitq = true;
|
|
break;
|
|
}
|
|
|
|
if (btintel_pcie_in_iml(data)) {
|
|
submit_rx = true;
|
|
signal_waitq = true;
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_FW_DL;
|
|
break;
|
|
}
|
|
break;
|
|
case BTINTEL_PCIE_INTEL_HCI_RESET2:
|
|
if (btintel_test_and_clear_flag(data->hdev, INTEL_WAIT_FOR_D0)) {
|
|
btintel_wake_up_flag(data->hdev, INTEL_WAIT_FOR_D0);
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_D0;
|
|
}
|
|
break;
|
|
case BTINTEL_PCIE_D0:
|
|
if (btintel_pcie_in_d3(data)) {
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_D3;
|
|
signal_waitq = true;
|
|
break;
|
|
}
|
|
break;
|
|
case BTINTEL_PCIE_D3:
|
|
if (btintel_pcie_in_d0(data)) {
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_D0;
|
|
submit_rx = true;
|
|
signal_waitq = true;
|
|
break;
|
|
}
|
|
break;
|
|
case BTINTEL_PCIE_HCI_RESET:
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_D0;
|
|
submit_rx = true;
|
|
signal_waitq = true;
|
|
break;
|
|
default:
|
|
bt_dev_err(data->hdev, "Unknown state: 0x%2.2x",
|
|
data->alive_intr_ctxt);
|
|
break;
|
|
}
|
|
|
|
if (submit_rx) {
|
|
btintel_pcie_reset_ia(data);
|
|
btintel_pcie_start_rx(data);
|
|
}
|
|
|
|
if (signal_waitq) {
|
|
bt_dev_dbg(data->hdev, "wake up gp0 wait_q");
|
|
wake_up(&data->gp0_wait_q);
|
|
}
|
|
|
|
if (old_ctxt != data->alive_intr_ctxt)
|
|
bt_dev_dbg(data->hdev, "alive context changed: %s -> %s",
|
|
btintel_pcie_alivectxt_state2str(old_ctxt),
|
|
btintel_pcie_alivectxt_state2str(data->alive_intr_ctxt));
|
|
}
|
|
|
|
/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
|
|
*/
|
|
static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
|
|
{
|
|
u16 cr_tia, cr_hia;
|
|
struct txq *txq;
|
|
struct urbd0 *urbd0;
|
|
|
|
cr_tia = data->ia.cr_tia[BTINTEL_PCIE_TXQ_NUM];
|
|
cr_hia = data->ia.cr_hia[BTINTEL_PCIE_TXQ_NUM];
|
|
|
|
if (cr_tia == cr_hia)
|
|
return;
|
|
|
|
txq = &data->txq;
|
|
|
|
while (cr_tia != cr_hia) {
|
|
data->tx_wait_done = true;
|
|
wake_up(&data->tx_wait_q);
|
|
|
|
urbd0 = &txq->urbd0s[cr_tia];
|
|
|
|
if (urbd0->tfd_index > txq->count)
|
|
return;
|
|
|
|
cr_tia = (cr_tia + 1) % txq->count;
|
|
data->ia.cr_tia[BTINTEL_PCIE_TXQ_NUM] = cr_tia;
|
|
ipc_print_ia_ring(data->hdev, &data->ia, BTINTEL_PCIE_TXQ_NUM);
|
|
}
|
|
}
|
|
|
|
static int btintel_pcie_recv_event(struct hci_dev *hdev, struct sk_buff *skb)
|
|
{
|
|
struct hci_event_hdr *hdr = (void *)skb->data;
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
|
|
if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
|
|
hdr->plen > 0) {
|
|
const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
|
|
unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
|
|
|
|
if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
|
|
switch (skb->data[2]) {
|
|
case 0x02:
|
|
/* When switching to the operational firmware
|
|
* the device sends a vendor specific event
|
|
* indicating that the bootup completed.
|
|
*/
|
|
btintel_bootup(hdev, ptr, len);
|
|
|
|
/* If bootup event is from operational image,
|
|
* driver needs to write sleep control register to
|
|
* move into D0 state
|
|
*/
|
|
if (btintel_pcie_in_op(data)) {
|
|
btintel_pcie_wr_sleep_cntrl(data, BTINTEL_PCIE_STATE_D0);
|
|
data->alive_intr_ctxt = BTINTEL_PCIE_INTEL_HCI_RESET2;
|
|
kfree_skb(skb);
|
|
return 0;
|
|
}
|
|
|
|
if (btintel_pcie_in_iml(data)) {
|
|
/* In case of IML, there is no concept
|
|
* of D0 transition. Just mimic as if
|
|
* IML moved to D0 by clearing INTEL_WAIT_FOR_D0
|
|
* bit and waking up the task waiting on
|
|
* INTEL_WAIT_FOR_D0. This is required
|
|
* as intel_boot() is common function for
|
|
* both IML and OP image loading.
|
|
*/
|
|
if (btintel_test_and_clear_flag(data->hdev,
|
|
INTEL_WAIT_FOR_D0))
|
|
btintel_wake_up_flag(data->hdev,
|
|
INTEL_WAIT_FOR_D0);
|
|
}
|
|
kfree_skb(skb);
|
|
return 0;
|
|
case 0x06:
|
|
/* When the firmware loading completes the
|
|
* device sends out a vendor specific event
|
|
* indicating the result of the firmware
|
|
* loading.
|
|
*/
|
|
btintel_secure_send_result(hdev, ptr, len);
|
|
kfree_skb(skb);
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
/* This is a debug event that comes from IML and OP image when it
|
|
* starts execution. There is no need pass this event to stack.
|
|
*/
|
|
if (skb->data[2] == 0x97) {
|
|
hci_recv_diag(hdev, skb);
|
|
return 0;
|
|
}
|
|
}
|
|
|
|
return hci_recv_frame(hdev, skb);
|
|
}
|
|
/* Process the received rx data
|
|
* It check the frame header to identify the data type and create skb
|
|
* and calling HCI API
|
|
*/
|
|
static int btintel_pcie_recv_frame(struct btintel_pcie_data *data,
|
|
struct sk_buff *skb)
|
|
{
|
|
int ret;
|
|
u8 pkt_type;
|
|
u16 plen;
|
|
u32 pcie_pkt_type;
|
|
void *pdata;
|
|
struct hci_dev *hdev = data->hdev;
|
|
|
|
spin_lock(&data->hci_rx_lock);
|
|
|
|
/* The first 4 bytes indicates the Intel PCIe specific packet type */
|
|
pdata = skb_pull_data(skb, BTINTEL_PCIE_HCI_TYPE_LEN);
|
|
if (!pdata) {
|
|
bt_dev_err(hdev, "Corrupted packet received");
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
|
|
pcie_pkt_type = get_unaligned_le32(pdata);
|
|
|
|
switch (pcie_pkt_type) {
|
|
case BTINTEL_PCIE_HCI_ACL_PKT:
|
|
if (skb->len >= HCI_ACL_HDR_SIZE) {
|
|
plen = HCI_ACL_HDR_SIZE + __le16_to_cpu(hci_acl_hdr(skb)->dlen);
|
|
pkt_type = HCI_ACLDATA_PKT;
|
|
} else {
|
|
bt_dev_err(hdev, "ACL packet is too short");
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
break;
|
|
|
|
case BTINTEL_PCIE_HCI_SCO_PKT:
|
|
if (skb->len >= HCI_SCO_HDR_SIZE) {
|
|
plen = HCI_SCO_HDR_SIZE + hci_sco_hdr(skb)->dlen;
|
|
pkt_type = HCI_SCODATA_PKT;
|
|
} else {
|
|
bt_dev_err(hdev, "SCO packet is too short");
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
break;
|
|
|
|
case BTINTEL_PCIE_HCI_EVT_PKT:
|
|
if (skb->len >= HCI_EVENT_HDR_SIZE) {
|
|
plen = HCI_EVENT_HDR_SIZE + hci_event_hdr(skb)->plen;
|
|
pkt_type = HCI_EVENT_PKT;
|
|
} else {
|
|
bt_dev_err(hdev, "Event packet is too short");
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
break;
|
|
|
|
case BTINTEL_PCIE_HCI_ISO_PKT:
|
|
if (skb->len >= HCI_ISO_HDR_SIZE) {
|
|
plen = HCI_ISO_HDR_SIZE + __le16_to_cpu(hci_iso_hdr(skb)->dlen);
|
|
pkt_type = HCI_ISODATA_PKT;
|
|
} else {
|
|
bt_dev_err(hdev, "ISO packet is too short");
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
break;
|
|
|
|
default:
|
|
bt_dev_err(hdev, "Invalid packet type received: 0x%4.4x",
|
|
pcie_pkt_type);
|
|
ret = -EINVAL;
|
|
goto exit_error;
|
|
}
|
|
|
|
if (skb->len < plen) {
|
|
bt_dev_err(hdev, "Received corrupted packet. type: 0x%2.2x",
|
|
pkt_type);
|
|
ret = -EILSEQ;
|
|
goto exit_error;
|
|
}
|
|
|
|
bt_dev_dbg(hdev, "pkt_type: 0x%2.2x len: %u", pkt_type, plen);
|
|
|
|
hci_skb_pkt_type(skb) = pkt_type;
|
|
hdev->stat.byte_rx += plen;
|
|
skb_trim(skb, plen);
|
|
|
|
if (pcie_pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
|
|
ret = btintel_pcie_recv_event(hdev, skb);
|
|
else
|
|
ret = hci_recv_frame(hdev, skb);
|
|
skb = NULL; /* skb is freed in the callee */
|
|
|
|
exit_error:
|
|
if (skb)
|
|
kfree_skb(skb);
|
|
|
|
if (ret)
|
|
hdev->stat.err_rx++;
|
|
|
|
spin_unlock(&data->hci_rx_lock);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void btintel_pcie_read_hwexp(struct btintel_pcie_data *data)
|
|
{
|
|
int len, err, offset, pending;
|
|
struct sk_buff *skb;
|
|
u8 *buf, prefix[64];
|
|
u32 addr, val;
|
|
u16 pkt_len;
|
|
|
|
struct tlv {
|
|
u8 type;
|
|
__le16 len;
|
|
u8 val[];
|
|
} __packed;
|
|
|
|
struct tlv *tlv;
|
|
|
|
switch (data->dmp_hdr.cnvi_top & 0xfff) {
|
|
case BTINTEL_CNVI_BLAZARI:
|
|
case BTINTEL_CNVI_BLAZARIW:
|
|
/* only from step B0 onwards */
|
|
if (INTEL_CNVX_TOP_STEP(data->dmp_hdr.cnvi_top) != 0x01)
|
|
return;
|
|
len = BTINTEL_PCIE_BLZR_HWEXP_SIZE; /* exception data length */
|
|
addr = BTINTEL_PCIE_BLZR_HWEXP_DMP_ADDR;
|
|
break;
|
|
case BTINTEL_CNVI_SCP:
|
|
len = BTINTEL_PCIE_SCP_HWEXP_SIZE;
|
|
addr = BTINTEL_PCIE_SCP_HWEXP_DMP_ADDR;
|
|
break;
|
|
default:
|
|
bt_dev_err(data->hdev, "Unsupported cnvi 0x%8.8x", data->dmp_hdr.cnvi_top);
|
|
return;
|
|
}
|
|
|
|
buf = kzalloc(len, GFP_KERNEL);
|
|
if (!buf)
|
|
goto exit_on_error;
|
|
|
|
btintel_pcie_mac_init(data);
|
|
|
|
err = btintel_pcie_read_device_mem(data, buf, addr, len);
|
|
if (err)
|
|
goto exit_on_error;
|
|
|
|
val = get_unaligned_le32(buf);
|
|
if (val != BTINTEL_PCIE_MAGIC_NUM) {
|
|
bt_dev_err(data->hdev, "Invalid exception dump signature: 0x%8.8x",
|
|
val);
|
|
goto exit_on_error;
|
|
}
|
|
|
|
snprintf(prefix, sizeof(prefix), "Bluetooth: %s: ", bt_dev_name(data->hdev));
|
|
|
|
offset = 4;
|
|
do {
|
|
pending = len - offset;
|
|
if (pending < sizeof(*tlv))
|
|
break;
|
|
tlv = (struct tlv *)(buf + offset);
|
|
|
|
/* If type == 0, then there are no more TLVs to be parsed */
|
|
if (!tlv->type) {
|
|
bt_dev_dbg(data->hdev, "Invalid TLV type 0");
|
|
break;
|
|
}
|
|
pkt_len = le16_to_cpu(tlv->len);
|
|
offset += sizeof(*tlv);
|
|
pending = len - offset;
|
|
if (pkt_len > pending)
|
|
break;
|
|
|
|
offset += pkt_len;
|
|
|
|
/* Only TLVs of type == 1 are HCI events, no need to process other
|
|
* TLVs
|
|
*/
|
|
if (tlv->type != 1)
|
|
continue;
|
|
|
|
bt_dev_dbg(data->hdev, "TLV packet length: %u", pkt_len);
|
|
if (pkt_len > HCI_MAX_EVENT_SIZE)
|
|
break;
|
|
skb = bt_skb_alloc(pkt_len, GFP_KERNEL);
|
|
if (!skb)
|
|
goto exit_on_error;
|
|
hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
|
|
skb_put_data(skb, tlv->val, pkt_len);
|
|
|
|
/* copy Intel specific pcie packet type */
|
|
val = BTINTEL_PCIE_HCI_EVT_PKT;
|
|
memcpy(skb_push(skb, BTINTEL_PCIE_HCI_TYPE_LEN), &val,
|
|
BTINTEL_PCIE_HCI_TYPE_LEN);
|
|
|
|
print_hex_dump(KERN_DEBUG, prefix, DUMP_PREFIX_OFFSET, 16, 1,
|
|
tlv->val, pkt_len, false);
|
|
|
|
btintel_pcie_recv_frame(data, skb);
|
|
} while (offset < len);
|
|
|
|
exit_on_error:
|
|
kfree(buf);
|
|
}
|
|
|
|
static void btintel_pcie_msix_hw_exp_handler(struct btintel_pcie_data *data)
|
|
{
|
|
bt_dev_err(data->hdev, "Received hw exception interrupt");
|
|
|
|
if (test_and_set_bit(BTINTEL_PCIE_CORE_HALTED, &data->flags))
|
|
return;
|
|
|
|
if (test_and_set_bit(BTINTEL_PCIE_HWEXP_INPROGRESS, &data->flags))
|
|
return;
|
|
|
|
/* Trigger device core dump when there is HW exception */
|
|
if (!test_and_set_bit(BTINTEL_PCIE_COREDUMP_INPROGRESS, &data->flags))
|
|
data->dmp_hdr.trigger_reason = BTINTEL_PCIE_TRIGGER_REASON_FW_ASSERT;
|
|
|
|
queue_work(data->workqueue, &data->rx_work);
|
|
}
|
|
|
|
static void btintel_pcie_rx_work(struct work_struct *work)
|
|
{
|
|
struct btintel_pcie_data *data = container_of(work,
|
|
struct btintel_pcie_data, rx_work);
|
|
struct sk_buff *skb;
|
|
|
|
if (test_bit(BTINTEL_PCIE_HWEXP_INPROGRESS, &data->flags)) {
|
|
/* Unlike usb products, controller will not send hardware
|
|
* exception event on exception. Instead controller writes the
|
|
* hardware event to device memory along with optional debug
|
|
* events, raises MSIX and halts. Driver shall read the
|
|
* exception event from device memory and passes it stack for
|
|
* further processing.
|
|
*/
|
|
btintel_pcie_read_hwexp(data);
|
|
clear_bit(BTINTEL_PCIE_HWEXP_INPROGRESS, &data->flags);
|
|
}
|
|
|
|
if (test_bit(BTINTEL_PCIE_COREDUMP_INPROGRESS, &data->flags)) {
|
|
btintel_pcie_dump_traces(data->hdev);
|
|
clear_bit(BTINTEL_PCIE_COREDUMP_INPROGRESS, &data->flags);
|
|
}
|
|
|
|
/* Process the sk_buf in queue and send to the HCI layer */
|
|
while ((skb = skb_dequeue(&data->rx_skb_q))) {
|
|
btintel_pcie_recv_frame(data, skb);
|
|
}
|
|
}
|
|
|
|
/* create sk_buff with data and save it to queue and start RX work */
|
|
static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8 status,
|
|
void *buf)
|
|
{
|
|
int ret, len;
|
|
struct rfh_hdr *rfh_hdr;
|
|
struct sk_buff *skb;
|
|
|
|
rfh_hdr = buf;
|
|
|
|
len = rfh_hdr->packet_len;
|
|
if (len <= 0) {
|
|
ret = -EINVAL;
|
|
goto resubmit;
|
|
}
|
|
|
|
/* Remove RFH header */
|
|
buf += sizeof(*rfh_hdr);
|
|
|
|
skb = alloc_skb(len, GFP_ATOMIC);
|
|
if (!skb)
|
|
goto resubmit;
|
|
|
|
skb_put_data(skb, buf, len);
|
|
skb_queue_tail(&data->rx_skb_q, skb);
|
|
queue_work(data->workqueue, &data->rx_work);
|
|
|
|
resubmit:
|
|
ret = btintel_pcie_submit_rx(data);
|
|
|
|
return ret;
|
|
}
|
|
|
|
/* Handles the MSI-X interrupt for rx queue 1 which is for RX */
|
|
static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
|
|
{
|
|
u16 cr_hia, cr_tia;
|
|
struct rxq *rxq;
|
|
struct urbd1 *urbd1;
|
|
struct data_buf *buf;
|
|
int ret;
|
|
struct hci_dev *hdev = data->hdev;
|
|
|
|
cr_hia = data->ia.cr_hia[BTINTEL_PCIE_RXQ_NUM];
|
|
cr_tia = data->ia.cr_tia[BTINTEL_PCIE_RXQ_NUM];
|
|
|
|
bt_dev_dbg(hdev, "RXQ: cr_hia: %u cr_tia: %u", cr_hia, cr_tia);
|
|
|
|
/* Check CR_TIA and CR_HIA for change */
|
|
if (cr_tia == cr_hia)
|
|
return;
|
|
|
|
rxq = &data->rxq;
|
|
|
|
/* The firmware sends multiple CD in a single MSI-X and it needs to
|
|
* process all received CDs in this interrupt.
|
|
*/
|
|
while (cr_tia != cr_hia) {
|
|
urbd1 = &rxq->urbd1s[cr_tia];
|
|
ipc_print_urbd1(data->hdev, urbd1, cr_tia);
|
|
|
|
buf = &rxq->bufs[urbd1->frbd_tag];
|
|
if (!buf) {
|
|
bt_dev_err(hdev, "RXQ: failed to get the DMA buffer for %d",
|
|
urbd1->frbd_tag);
|
|
return;
|
|
}
|
|
|
|
ret = btintel_pcie_submit_rx_work(data, urbd1->status,
|
|
buf->data);
|
|
if (ret) {
|
|
bt_dev_err(hdev, "RXQ: failed to submit rx request");
|
|
return;
|
|
}
|
|
|
|
cr_tia = (cr_tia + 1) % rxq->count;
|
|
data->ia.cr_tia[BTINTEL_PCIE_RXQ_NUM] = cr_tia;
|
|
ipc_print_ia_ring(data->hdev, &data->ia, BTINTEL_PCIE_RXQ_NUM);
|
|
}
|
|
}
|
|
|
|
static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
|
|
{
|
|
return IRQ_WAKE_THREAD;
|
|
}
|
|
|
|
static inline bool btintel_pcie_is_rxq_empty(struct btintel_pcie_data *data)
|
|
{
|
|
return data->ia.cr_hia[BTINTEL_PCIE_RXQ_NUM] == data->ia.cr_tia[BTINTEL_PCIE_RXQ_NUM];
|
|
}
|
|
|
|
static inline bool btintel_pcie_is_txackq_empty(struct btintel_pcie_data *data)
|
|
{
|
|
return data->ia.cr_tia[BTINTEL_PCIE_TXQ_NUM] == data->ia.cr_hia[BTINTEL_PCIE_TXQ_NUM];
|
|
}
|
|
|
|
static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
|
|
{
|
|
struct msix_entry *entry = dev_id;
|
|
struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
|
|
u32 intr_fh, intr_hw;
|
|
|
|
spin_lock(&data->irq_lock);
|
|
intr_fh = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_MSIX_FH_INT_CAUSES);
|
|
intr_hw = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_MSIX_HW_INT_CAUSES);
|
|
|
|
/* Clear causes registers to avoid being handling the same cause */
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_FH_INT_CAUSES, intr_fh);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_HW_INT_CAUSES, intr_hw);
|
|
spin_unlock(&data->irq_lock);
|
|
|
|
if (unlikely(!(intr_fh | intr_hw))) {
|
|
/* Ignore interrupt, inta == 0 */
|
|
return IRQ_NONE;
|
|
}
|
|
|
|
/* This interrupt is raised when there is an hardware exception */
|
|
if (intr_hw & BTINTEL_PCIE_MSIX_HW_INT_CAUSES_HWEXP)
|
|
btintel_pcie_msix_hw_exp_handler(data);
|
|
|
|
if (intr_hw & BTINTEL_PCIE_MSIX_HW_INT_CAUSES_GP1)
|
|
btintel_pcie_msix_gp1_handler(data);
|
|
|
|
/* This interrupt is triggered by the firmware after updating
|
|
* boot_stage register and image_response register
|
|
*/
|
|
if (intr_hw & BTINTEL_PCIE_MSIX_HW_INT_CAUSES_GP0)
|
|
btintel_pcie_msix_gp0_handler(data);
|
|
|
|
/* For TX */
|
|
if (intr_fh & BTINTEL_PCIE_MSIX_FH_INT_CAUSES_0) {
|
|
btintel_pcie_msix_tx_handle(data);
|
|
if (!btintel_pcie_is_rxq_empty(data))
|
|
btintel_pcie_msix_rx_handle(data);
|
|
}
|
|
|
|
/* For RX */
|
|
if (intr_fh & BTINTEL_PCIE_MSIX_FH_INT_CAUSES_1) {
|
|
btintel_pcie_msix_rx_handle(data);
|
|
if (!btintel_pcie_is_txackq_empty(data))
|
|
btintel_pcie_msix_tx_handle(data);
|
|
}
|
|
|
|
/*
|
|
* Before sending the interrupt the HW disables it to prevent a nested
|
|
* interrupt. This is done by writing 1 to the corresponding bit in
|
|
* the mask register. After handling the interrupt, it should be
|
|
* re-enabled by clearing this bit. This register is defined as write 1
|
|
* clear (W1C) register, meaning that it's cleared by writing 1
|
|
* to the bit.
|
|
*/
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_AUTOMASK_ST,
|
|
BIT(entry->entry));
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
/* This function requests the irq for MSI-X and registers the handlers per irq.
|
|
* Currently, it requests only 1 irq for all interrupt causes.
|
|
*/
|
|
static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
|
|
{
|
|
int err;
|
|
int num_irqs, i;
|
|
|
|
for (i = 0; i < BTINTEL_PCIE_MSIX_VEC_MAX; i++)
|
|
data->msix_entries[i].entry = i;
|
|
|
|
num_irqs = pci_alloc_irq_vectors(data->pdev, BTINTEL_PCIE_MSIX_VEC_MIN,
|
|
BTINTEL_PCIE_MSIX_VEC_MAX, PCI_IRQ_MSIX);
|
|
if (num_irqs < 0)
|
|
return num_irqs;
|
|
|
|
data->alloc_vecs = num_irqs;
|
|
data->msix_enabled = 1;
|
|
data->def_irq = 0;
|
|
|
|
/* setup irq handler */
|
|
for (i = 0; i < data->alloc_vecs; i++) {
|
|
struct msix_entry *msix_entry;
|
|
|
|
msix_entry = &data->msix_entries[i];
|
|
msix_entry->vector = pci_irq_vector(data->pdev, i);
|
|
|
|
err = devm_request_threaded_irq(&data->pdev->dev,
|
|
msix_entry->vector,
|
|
btintel_pcie_msix_isr,
|
|
btintel_pcie_irq_msix_handler,
|
|
IRQF_SHARED,
|
|
KBUILD_MODNAME,
|
|
msix_entry);
|
|
if (err) {
|
|
pci_free_irq_vectors(data->pdev);
|
|
data->alloc_vecs = 0;
|
|
return err;
|
|
}
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
struct btintel_pcie_causes_list {
|
|
u32 cause;
|
|
u32 mask_reg;
|
|
u8 cause_num;
|
|
};
|
|
|
|
static struct btintel_pcie_causes_list causes_list[] = {
|
|
{ BTINTEL_PCIE_MSIX_FH_INT_CAUSES_0, BTINTEL_PCIE_CSR_MSIX_FH_INT_MASK, 0x00 },
|
|
{ BTINTEL_PCIE_MSIX_FH_INT_CAUSES_1, BTINTEL_PCIE_CSR_MSIX_FH_INT_MASK, 0x01 },
|
|
{ BTINTEL_PCIE_MSIX_HW_INT_CAUSES_GP0, BTINTEL_PCIE_CSR_MSIX_HW_INT_MASK, 0x20 },
|
|
{ BTINTEL_PCIE_MSIX_HW_INT_CAUSES_HWEXP, BTINTEL_PCIE_CSR_MSIX_HW_INT_MASK, 0x23 },
|
|
};
|
|
|
|
/* This function configures the interrupt masks for both HW_INT_CAUSES and
|
|
* FH_INT_CAUSES which are meaningful to us.
|
|
*
|
|
* After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
|
|
* need to call this function again to configure since the masks
|
|
* are reset to 0xFFFFFFFF after reset.
|
|
*/
|
|
static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
|
|
{
|
|
int i;
|
|
int val = data->def_irq | BTINTEL_PCIE_MSIX_NON_AUTO_CLEAR_CAUSE;
|
|
|
|
/* Set Non Auto Clear Cause */
|
|
for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
|
|
btintel_pcie_wr_reg8(data,
|
|
BTINTEL_PCIE_CSR_MSIX_IVAR(causes_list[i].cause_num),
|
|
val);
|
|
btintel_pcie_clr_reg_bits(data,
|
|
causes_list[i].mask_reg,
|
|
causes_list[i].cause);
|
|
}
|
|
|
|
/* Save the initial interrupt mask */
|
|
data->fh_init_mask = ~btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_MSIX_FH_INT_MASK);
|
|
data->hw_init_mask = ~btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_MSIX_HW_INT_MASK);
|
|
}
|
|
|
|
static int btintel_pcie_config_pcie(struct pci_dev *pdev,
|
|
struct btintel_pcie_data *data)
|
|
{
|
|
int err;
|
|
|
|
err = pcim_enable_device(pdev);
|
|
if (err)
|
|
return err;
|
|
|
|
pci_set_master(pdev);
|
|
|
|
err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
|
|
if (err) {
|
|
err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
|
|
if (err)
|
|
return err;
|
|
}
|
|
|
|
data->base_addr = pcim_iomap_region(pdev, 0, KBUILD_MODNAME);
|
|
if (IS_ERR(data->base_addr))
|
|
return PTR_ERR(data->base_addr);
|
|
|
|
err = btintel_pcie_setup_irq(data);
|
|
if (err)
|
|
return err;
|
|
|
|
/* Configure MSI-X with causes list */
|
|
btintel_pcie_config_msix(data);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
|
|
struct ctx_info *ci)
|
|
{
|
|
ci->version = 0x1;
|
|
ci->size = sizeof(*ci);
|
|
ci->config = 0x0000;
|
|
ci->addr_cr_hia = data->ia.cr_hia_p_addr;
|
|
ci->addr_tr_tia = data->ia.tr_tia_p_addr;
|
|
ci->addr_cr_tia = data->ia.cr_tia_p_addr;
|
|
ci->addr_tr_hia = data->ia.tr_hia_p_addr;
|
|
ci->num_cr_ia = BTINTEL_PCIE_NUM_QUEUES;
|
|
ci->num_tr_ia = BTINTEL_PCIE_NUM_QUEUES;
|
|
ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
|
|
ci->addr_tfdq = data->txq.tfds_p_addr;
|
|
ci->num_tfdq = data->txq.count;
|
|
ci->num_urbdq0 = data->txq.count;
|
|
ci->tfdq_db_vec = BTINTEL_PCIE_TXQ_NUM;
|
|
ci->urbdq0_db_vec = BTINTEL_PCIE_TXQ_NUM;
|
|
ci->rbd_size = BTINTEL_PCIE_RBD_SIZE_4K;
|
|
ci->addr_frbdq = data->rxq.frbds_p_addr;
|
|
ci->num_frbdq = data->rxq.count;
|
|
ci->frbdq_db_vec = BTINTEL_PCIE_RXQ_NUM;
|
|
ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
|
|
ci->num_urbdq1 = data->rxq.count;
|
|
ci->urbdq_db_vec = BTINTEL_PCIE_RXQ_NUM;
|
|
|
|
ci->dbg_output_mode = 0x01;
|
|
ci->dbgc_addr = data->dbgc.frag_p_addr;
|
|
ci->dbgc_size = data->dbgc.frag_size;
|
|
ci->dbg_preset = 0x00;
|
|
}
|
|
|
|
static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
|
|
struct txq *txq)
|
|
{
|
|
/* Free data buffers first */
|
|
dma_free_coherent(&data->pdev->dev, txq->count * BTINTEL_PCIE_BUFFER_SIZE,
|
|
txq->buf_v_addr, txq->buf_p_addr);
|
|
kfree(txq->bufs);
|
|
}
|
|
|
|
static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
|
|
struct txq *txq)
|
|
{
|
|
int i;
|
|
struct data_buf *buf;
|
|
|
|
/* Allocate the same number of buffers as the descriptor */
|
|
txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
|
|
if (!txq->bufs)
|
|
return -ENOMEM;
|
|
|
|
/* Allocate full chunk of data buffer for DMA first and do indexing and
|
|
* initialization next, so it can be freed easily
|
|
*/
|
|
txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
|
|
txq->count * BTINTEL_PCIE_BUFFER_SIZE,
|
|
&txq->buf_p_addr,
|
|
GFP_KERNEL | __GFP_NOWARN);
|
|
if (!txq->buf_v_addr) {
|
|
kfree(txq->bufs);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
/* Setup the allocated DMA buffer to bufs. Each data_buf should
|
|
* have virtual address and physical address
|
|
*/
|
|
for (i = 0; i < txq->count; i++) {
|
|
buf = &txq->bufs[i];
|
|
buf->data_p_addr = txq->buf_p_addr + (i * BTINTEL_PCIE_BUFFER_SIZE);
|
|
buf->data = txq->buf_v_addr + (i * BTINTEL_PCIE_BUFFER_SIZE);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
|
|
struct rxq *rxq)
|
|
{
|
|
/* Free data buffers first */
|
|
dma_free_coherent(&data->pdev->dev, rxq->count * BTINTEL_PCIE_BUFFER_SIZE,
|
|
rxq->buf_v_addr, rxq->buf_p_addr);
|
|
kfree(rxq->bufs);
|
|
}
|
|
|
|
static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
|
|
struct rxq *rxq)
|
|
{
|
|
int i;
|
|
struct data_buf *buf;
|
|
|
|
/* Allocate the same number of buffers as the descriptor */
|
|
rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
|
|
if (!rxq->bufs)
|
|
return -ENOMEM;
|
|
|
|
/* Allocate full chunk of data buffer for DMA first and do indexing and
|
|
* initialization next, so it can be freed easily
|
|
*/
|
|
rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
|
|
rxq->count * BTINTEL_PCIE_BUFFER_SIZE,
|
|
&rxq->buf_p_addr,
|
|
GFP_KERNEL | __GFP_NOWARN);
|
|
if (!rxq->buf_v_addr) {
|
|
kfree(rxq->bufs);
|
|
return -ENOMEM;
|
|
}
|
|
|
|
/* Setup the allocated DMA buffer to bufs. Each data_buf should
|
|
* have virtual address and physical address
|
|
*/
|
|
for (i = 0; i < rxq->count; i++) {
|
|
buf = &rxq->bufs[i];
|
|
buf->data_p_addr = rxq->buf_p_addr + (i * BTINTEL_PCIE_BUFFER_SIZE);
|
|
buf->data = rxq->buf_v_addr + (i * BTINTEL_PCIE_BUFFER_SIZE);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
|
|
dma_addr_t p_addr, void *v_addr,
|
|
struct ia *ia)
|
|
{
|
|
/* TR Head Index Array */
|
|
ia->tr_hia_p_addr = p_addr;
|
|
ia->tr_hia = v_addr;
|
|
|
|
/* TR Tail Index Array */
|
|
ia->tr_tia_p_addr = p_addr + sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES;
|
|
ia->tr_tia = v_addr + sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES;
|
|
|
|
/* CR Head index Array */
|
|
ia->cr_hia_p_addr = p_addr + (sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 2);
|
|
ia->cr_hia = v_addr + (sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 2);
|
|
|
|
/* CR Tail Index Array */
|
|
ia->cr_tia_p_addr = p_addr + (sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 3);
|
|
ia->cr_tia = v_addr + (sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 3);
|
|
}
|
|
|
|
static void btintel_pcie_free(struct btintel_pcie_data *data)
|
|
{
|
|
btintel_pcie_free_rxq_bufs(data, &data->rxq);
|
|
btintel_pcie_free_txq_bufs(data, &data->txq);
|
|
|
|
dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
|
|
dma_pool_destroy(data->dma_pool);
|
|
}
|
|
|
|
/* Allocate tx and rx queues, any related data structures and buffers.
|
|
*/
|
|
static int btintel_pcie_alloc(struct btintel_pcie_data *data)
|
|
{
|
|
int err = 0;
|
|
size_t total;
|
|
dma_addr_t p_addr;
|
|
void *v_addr;
|
|
|
|
/* Allocate the chunk of DMA memory for descriptors, index array, and
|
|
* context information, instead of allocating individually.
|
|
* The DMA memory for data buffer is allocated while setting up the
|
|
* each queue.
|
|
*
|
|
* Total size is sum of the following
|
|
* + size of TFD * Number of descriptors in queue
|
|
* + size of URBD0 * Number of descriptors in queue
|
|
* + size of FRBD * Number of descriptors in queue
|
|
* + size of URBD1 * Number of descriptors in queue
|
|
* + size of index * Number of queues(2) * type of index array(4)
|
|
* + size of context information
|
|
*/
|
|
total = (sizeof(struct tfd) + sizeof(struct urbd0)) * BTINTEL_PCIE_TX_DESCS_COUNT;
|
|
total += (sizeof(struct frbd) + sizeof(struct urbd1)) * BTINTEL_PCIE_RX_DESCS_COUNT;
|
|
|
|
/* Add the sum of size of index array and size of ci struct */
|
|
total += (sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 4) + sizeof(struct ctx_info);
|
|
|
|
/* Allocate DMA Pool */
|
|
data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data->pdev->dev,
|
|
total, BTINTEL_PCIE_DMA_POOL_ALIGNMENT, 0);
|
|
if (!data->dma_pool) {
|
|
err = -ENOMEM;
|
|
goto exit_error;
|
|
}
|
|
|
|
v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL | __GFP_NOWARN,
|
|
&p_addr);
|
|
if (!v_addr) {
|
|
dma_pool_destroy(data->dma_pool);
|
|
err = -ENOMEM;
|
|
goto exit_error;
|
|
}
|
|
|
|
data->dma_p_addr = p_addr;
|
|
data->dma_v_addr = v_addr;
|
|
|
|
/* Setup descriptor count */
|
|
data->txq.count = BTINTEL_PCIE_TX_DESCS_COUNT;
|
|
data->rxq.count = BTINTEL_PCIE_RX_DESCS_COUNT;
|
|
|
|
/* Setup tfds */
|
|
data->txq.tfds_p_addr = p_addr;
|
|
data->txq.tfds = v_addr;
|
|
|
|
p_addr += (sizeof(struct tfd) * BTINTEL_PCIE_TX_DESCS_COUNT);
|
|
v_addr += (sizeof(struct tfd) * BTINTEL_PCIE_TX_DESCS_COUNT);
|
|
|
|
/* Setup urbd0 */
|
|
data->txq.urbd0s_p_addr = p_addr;
|
|
data->txq.urbd0s = v_addr;
|
|
|
|
p_addr += (sizeof(struct urbd0) * BTINTEL_PCIE_TX_DESCS_COUNT);
|
|
v_addr += (sizeof(struct urbd0) * BTINTEL_PCIE_TX_DESCS_COUNT);
|
|
|
|
/* Setup FRBD*/
|
|
data->rxq.frbds_p_addr = p_addr;
|
|
data->rxq.frbds = v_addr;
|
|
|
|
p_addr += (sizeof(struct frbd) * BTINTEL_PCIE_RX_DESCS_COUNT);
|
|
v_addr += (sizeof(struct frbd) * BTINTEL_PCIE_RX_DESCS_COUNT);
|
|
|
|
/* Setup urbd1 */
|
|
data->rxq.urbd1s_p_addr = p_addr;
|
|
data->rxq.urbd1s = v_addr;
|
|
|
|
p_addr += (sizeof(struct urbd1) * BTINTEL_PCIE_RX_DESCS_COUNT);
|
|
v_addr += (sizeof(struct urbd1) * BTINTEL_PCIE_RX_DESCS_COUNT);
|
|
|
|
/* Setup data buffers for txq */
|
|
err = btintel_pcie_setup_txq_bufs(data, &data->txq);
|
|
if (err)
|
|
goto exit_error_pool;
|
|
|
|
/* Setup data buffers for rxq */
|
|
err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
|
|
if (err)
|
|
goto exit_error_txq;
|
|
|
|
/* Setup Index Array */
|
|
btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
|
|
|
|
/* Setup data buffers for dbgc */
|
|
err = btintel_pcie_setup_dbgc(data);
|
|
if (err)
|
|
goto exit_error_txq;
|
|
|
|
/* Setup Context Information */
|
|
p_addr += sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 4;
|
|
v_addr += sizeof(u16) * BTINTEL_PCIE_NUM_QUEUES * 4;
|
|
|
|
data->ci = v_addr;
|
|
data->ci_p_addr = p_addr;
|
|
|
|
/* Initialize the CI */
|
|
btintel_pcie_init_ci(data, data->ci);
|
|
|
|
return 0;
|
|
|
|
exit_error_txq:
|
|
btintel_pcie_free_txq_bufs(data, &data->txq);
|
|
exit_error_pool:
|
|
dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
|
|
dma_pool_destroy(data->dma_pool);
|
|
exit_error:
|
|
return err;
|
|
}
|
|
|
|
static int btintel_pcie_open(struct hci_dev *hdev)
|
|
{
|
|
bt_dev_dbg(hdev, "");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int btintel_pcie_close(struct hci_dev *hdev)
|
|
{
|
|
bt_dev_dbg(hdev, "");
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int btintel_pcie_inject_cmd_complete(struct hci_dev *hdev, __u16 opcode)
|
|
{
|
|
struct sk_buff *skb;
|
|
struct hci_event_hdr *hdr;
|
|
struct hci_ev_cmd_complete *evt;
|
|
|
|
skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
|
|
if (!skb)
|
|
return -ENOMEM;
|
|
|
|
hdr = (struct hci_event_hdr *)skb_put(skb, sizeof(*hdr));
|
|
hdr->evt = HCI_EV_CMD_COMPLETE;
|
|
hdr->plen = sizeof(*evt) + 1;
|
|
|
|
evt = (struct hci_ev_cmd_complete *)skb_put(skb, sizeof(*evt));
|
|
evt->ncmd = 0x01;
|
|
evt->opcode = cpu_to_le16(opcode);
|
|
|
|
*(u8 *)skb_put(skb, 1) = 0x00;
|
|
|
|
hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
|
|
|
|
return hci_recv_frame(hdev, skb);
|
|
}
|
|
|
|
static int btintel_pcie_send_frame(struct hci_dev *hdev,
|
|
struct sk_buff *skb)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
struct hci_command_hdr *cmd;
|
|
__u16 opcode = ~0;
|
|
int ret;
|
|
u32 type;
|
|
|
|
if (test_bit(BTINTEL_PCIE_CORE_HALTED, &data->flags))
|
|
return -ENODEV;
|
|
|
|
/* Due to the fw limitation, the type header of the packet should be
|
|
* 4 bytes unlike 1 byte for UART. In UART, the firmware can read
|
|
* the first byte to get the packet type and redirect the rest of data
|
|
* packet to the right handler.
|
|
*
|
|
* But for PCIe, THF(Transfer Flow Handler) fetches the 4 bytes of data
|
|
* from DMA memory and by the time it reads the first 4 bytes, it has
|
|
* already consumed some part of packet. Thus the packet type indicator
|
|
* for iBT PCIe is 4 bytes.
|
|
*
|
|
* Luckily, when HCI core creates the skb, it allocates 8 bytes of
|
|
* head room for profile and driver use, and before sending the data
|
|
* to the device, append the iBT PCIe packet type in the front.
|
|
*/
|
|
switch (hci_skb_pkt_type(skb)) {
|
|
case HCI_COMMAND_PKT:
|
|
type = BTINTEL_PCIE_HCI_CMD_PKT;
|
|
cmd = (void *)skb->data;
|
|
opcode = le16_to_cpu(cmd->opcode);
|
|
if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
|
|
struct hci_command_hdr *cmd = (void *)skb->data;
|
|
__u16 opcode = le16_to_cpu(cmd->opcode);
|
|
|
|
/* When the BTINTEL_HCI_OP_RESET command is issued to
|
|
* boot into the operational firmware, it will actually
|
|
* not send a command complete event. To keep the flow
|
|
* control working inject that event here.
|
|
*/
|
|
if (opcode == BTINTEL_HCI_OP_RESET)
|
|
btintel_pcie_inject_cmd_complete(hdev, opcode);
|
|
}
|
|
|
|
hdev->stat.cmd_tx++;
|
|
break;
|
|
case HCI_ACLDATA_PKT:
|
|
type = BTINTEL_PCIE_HCI_ACL_PKT;
|
|
hdev->stat.acl_tx++;
|
|
break;
|
|
case HCI_SCODATA_PKT:
|
|
type = BTINTEL_PCIE_HCI_SCO_PKT;
|
|
hdev->stat.sco_tx++;
|
|
break;
|
|
case HCI_ISODATA_PKT:
|
|
type = BTINTEL_PCIE_HCI_ISO_PKT;
|
|
break;
|
|
default:
|
|
bt_dev_err(hdev, "Unknown HCI packet type");
|
|
return -EILSEQ;
|
|
}
|
|
|
|
ret = btintel_pcie_send_sync(data, skb, type, opcode);
|
|
if (ret) {
|
|
hdev->stat.err_tx++;
|
|
bt_dev_err(hdev, "Failed to send frame (%d)", ret);
|
|
goto exit_error;
|
|
}
|
|
|
|
hdev->stat.byte_tx += skb->len;
|
|
kfree_skb(skb);
|
|
|
|
exit_error:
|
|
return ret;
|
|
}
|
|
|
|
static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
|
|
{
|
|
struct hci_dev *hdev;
|
|
|
|
hdev = data->hdev;
|
|
hci_unregister_dev(hdev);
|
|
hci_free_dev(hdev);
|
|
data->hdev = NULL;
|
|
}
|
|
|
|
static void btintel_pcie_disable_interrupts(struct btintel_pcie_data *data)
|
|
{
|
|
spin_lock(&data->irq_lock);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_FH_INT_MASK, data->fh_init_mask);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_HW_INT_MASK, data->hw_init_mask);
|
|
spin_unlock(&data->irq_lock);
|
|
}
|
|
|
|
static void btintel_pcie_enable_interrupts(struct btintel_pcie_data *data)
|
|
{
|
|
spin_lock(&data->irq_lock);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_FH_INT_MASK, ~data->fh_init_mask);
|
|
btintel_pcie_wr_reg32(data, BTINTEL_PCIE_CSR_MSIX_HW_INT_MASK, ~data->hw_init_mask);
|
|
spin_unlock(&data->irq_lock);
|
|
}
|
|
|
|
static void btintel_pcie_synchronize_irqs(struct btintel_pcie_data *data)
|
|
{
|
|
for (int i = 0; i < data->alloc_vecs; i++)
|
|
synchronize_irq(data->msix_entries[i].vector);
|
|
}
|
|
|
|
static int btintel_pcie_setup_internal(struct hci_dev *hdev)
|
|
{
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
const u8 param[1] = { 0xFF };
|
|
struct intel_version_tlv ver_tlv;
|
|
struct sk_buff *skb;
|
|
int err;
|
|
|
|
BT_DBG("%s", hdev->name);
|
|
|
|
skb = __hci_cmd_sync(hdev, 0xfc05, 1, param, HCI_CMD_TIMEOUT);
|
|
if (IS_ERR(skb)) {
|
|
bt_dev_err(hdev, "Reading Intel version command failed (%ld)",
|
|
PTR_ERR(skb));
|
|
return PTR_ERR(skb);
|
|
}
|
|
|
|
/* Check the status */
|
|
if (skb->data[0]) {
|
|
bt_dev_err(hdev, "Intel Read Version command failed (%02x)",
|
|
skb->data[0]);
|
|
err = -EIO;
|
|
goto exit_error;
|
|
}
|
|
|
|
/* Apply the common HCI quirks for Intel device */
|
|
hci_set_quirk(hdev, HCI_QUIRK_STRICT_DUPLICATE_FILTER);
|
|
hci_set_quirk(hdev, HCI_QUIRK_SIMULTANEOUS_DISCOVERY);
|
|
hci_set_quirk(hdev, HCI_QUIRK_NON_PERSISTENT_DIAG);
|
|
|
|
/* Set up the quality report callback for Intel devices */
|
|
hdev->set_quality_report = btintel_set_quality_report;
|
|
|
|
memset(&ver_tlv, 0, sizeof(ver_tlv));
|
|
/* For TLV type device, parse the tlv data */
|
|
err = btintel_parse_version_tlv(hdev, &ver_tlv, skb);
|
|
if (err) {
|
|
bt_dev_err(hdev, "Failed to parse TLV version information");
|
|
goto exit_error;
|
|
}
|
|
|
|
switch (INTEL_HW_PLATFORM(ver_tlv.cnvi_bt)) {
|
|
case 0x37:
|
|
break;
|
|
default:
|
|
bt_dev_err(hdev, "Unsupported Intel hardware platform (0x%2x)",
|
|
INTEL_HW_PLATFORM(ver_tlv.cnvi_bt));
|
|
err = -EINVAL;
|
|
goto exit_error;
|
|
}
|
|
|
|
/* Check for supported iBT hardware variants of this firmware
|
|
* loading method.
|
|
*
|
|
* This check has been put in place to ensure correct forward
|
|
* compatibility options when newer hardware variants come
|
|
* along.
|
|
*/
|
|
switch (INTEL_HW_VARIANT(ver_tlv.cnvi_bt)) {
|
|
case 0x1e: /* BzrI */
|
|
case 0x1f: /* ScP */
|
|
/* Display version information of TLV type */
|
|
btintel_version_info_tlv(hdev, &ver_tlv);
|
|
|
|
/* Apply the device specific HCI quirks for TLV based devices
|
|
*
|
|
* All TLV based devices support WBS
|
|
*/
|
|
hci_set_quirk(hdev, HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED);
|
|
|
|
/* Setup MSFT Extension support */
|
|
btintel_set_msft_opcode(hdev,
|
|
INTEL_HW_VARIANT(ver_tlv.cnvi_bt));
|
|
|
|
err = btintel_bootloader_setup_tlv(hdev, &ver_tlv);
|
|
if (err)
|
|
goto exit_error;
|
|
break;
|
|
default:
|
|
bt_dev_err(hdev, "Unsupported Intel hw variant (%u)",
|
|
INTEL_HW_VARIANT(ver_tlv.cnvi_bt));
|
|
err = -EINVAL;
|
|
goto exit_error;
|
|
break;
|
|
}
|
|
|
|
data->dmp_hdr.cnvi_top = ver_tlv.cnvi_top;
|
|
data->dmp_hdr.cnvr_top = ver_tlv.cnvr_top;
|
|
data->dmp_hdr.fw_timestamp = ver_tlv.timestamp;
|
|
data->dmp_hdr.fw_build_type = ver_tlv.build_type;
|
|
data->dmp_hdr.fw_build_num = ver_tlv.build_num;
|
|
data->dmp_hdr.cnvi_bt = ver_tlv.cnvi_bt;
|
|
|
|
if (ver_tlv.img_type == 0x02 || ver_tlv.img_type == 0x03)
|
|
data->dmp_hdr.fw_git_sha1 = ver_tlv.git_sha1;
|
|
|
|
err = hci_devcd_register(hdev, btintel_pcie_dump_traces, btintel_pcie_dump_hdr,
|
|
btintel_pcie_dump_notify);
|
|
if (err) {
|
|
bt_dev_err(hdev, "Failed to register coredump (%d)", err);
|
|
goto exit_error;
|
|
}
|
|
|
|
btintel_print_fseq_info(hdev);
|
|
exit_error:
|
|
kfree_skb(skb);
|
|
|
|
return err;
|
|
}
|
|
|
|
static int btintel_pcie_setup(struct hci_dev *hdev)
|
|
{
|
|
int err, fw_dl_retry = 0;
|
|
struct btintel_pcie_data *data = hci_get_drvdata(hdev);
|
|
|
|
while ((err = btintel_pcie_setup_internal(hdev)) && fw_dl_retry++ < 1) {
|
|
bt_dev_err(hdev, "Firmware download retry count: %d",
|
|
fw_dl_retry);
|
|
btintel_pcie_dump_debug_registers(hdev);
|
|
btintel_pcie_disable_interrupts(data);
|
|
btintel_pcie_synchronize_irqs(data);
|
|
err = btintel_pcie_reset_bt(data);
|
|
if (err) {
|
|
bt_dev_err(hdev, "Failed to do shr reset: %d", err);
|
|
break;
|
|
}
|
|
usleep_range(10000, 12000);
|
|
btintel_pcie_reset_ia(data);
|
|
btintel_pcie_enable_interrupts(data);
|
|
btintel_pcie_config_msix(data);
|
|
err = btintel_pcie_enable_bt(data);
|
|
if (err) {
|
|
bt_dev_err(hdev, "Failed to enable hardware: %d", err);
|
|
break;
|
|
}
|
|
btintel_pcie_start_rx(data);
|
|
}
|
|
|
|
if (!err)
|
|
set_bit(BTINTEL_PCIE_SETUP_DONE, &data->flags);
|
|
return err;
|
|
}
|
|
|
|
static struct btintel_pcie_dev_recovery *
|
|
btintel_pcie_get_recovery(struct pci_dev *pdev, struct device *dev)
|
|
{
|
|
struct btintel_pcie_dev_recovery *tmp, *data = NULL;
|
|
const char *name = pci_name(pdev);
|
|
struct hci_dev *hdev = to_hci_dev(dev);
|
|
|
|
spin_lock(&btintel_pcie_recovery_lock);
|
|
list_for_each_entry(tmp, &btintel_pcie_recovery_list, list) {
|
|
if (strcmp(tmp->name, name))
|
|
continue;
|
|
data = tmp;
|
|
break;
|
|
}
|
|
spin_unlock(&btintel_pcie_recovery_lock);
|
|
|
|
if (data) {
|
|
bt_dev_dbg(hdev, "Found restart data for BDF: %s", data->name);
|
|
return data;
|
|
}
|
|
|
|
data = kzalloc(struct_size(data, name, strlen(name) + 1), GFP_ATOMIC);
|
|
if (!data)
|
|
return NULL;
|
|
|
|
strscpy_pad(data->name, name, strlen(name) + 1);
|
|
spin_lock(&btintel_pcie_recovery_lock);
|
|
list_add_tail(&data->list, &btintel_pcie_recovery_list);
|
|
spin_unlock(&btintel_pcie_recovery_lock);
|
|
|
|
return data;
|
|
}
|
|
|
|
static void btintel_pcie_free_restart_list(void)
|
|
{
|
|
struct btintel_pcie_dev_recovery *tmp;
|
|
|
|
while ((tmp = list_first_entry_or_null(&btintel_pcie_recovery_list,
|
|
typeof(*tmp), list))) {
|
|
list_del(&tmp->list);
|
|
kfree(tmp);
|
|
}
|
|
}
|
|
|
|
static void btintel_pcie_inc_recovery_count(struct pci_dev *pdev,
|
|
struct device *dev)
|
|
{
|
|
struct btintel_pcie_dev_recovery *data;
|
|
time64_t retry_window;
|
|
|
|
data = btintel_pcie_get_recovery(pdev, dev);
|
|
if (!data)
|
|
return;
|
|
|
|
retry_window = ktime_get_boottime_seconds() - data->last_error;
|
|
if (data->count == 0) {
|
|
data->last_error = ktime_get_boottime_seconds();
|
|
data->count++;
|
|
} else if (retry_window < BTINTEL_PCIE_RESET_WINDOW_SECS &&
|
|
data->count <= BTINTEL_PCIE_FLR_MAX_RETRY) {
|
|
data->count++;
|
|
} else if (retry_window > BTINTEL_PCIE_RESET_WINDOW_SECS) {
|
|
data->last_error = 0;
|
|
data->count = 0;
|
|
}
|
|
}
|
|
|
|
static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data);
|
|
|
|
static void btintel_pcie_removal_work(struct work_struct *wk)
|
|
{
|
|
struct btintel_pcie_removal *removal =
|
|
container_of(wk, struct btintel_pcie_removal, work);
|
|
struct pci_dev *pdev = removal->pdev;
|
|
struct btintel_pcie_data *data;
|
|
int err;
|
|
|
|
pci_lock_rescan_remove();
|
|
|
|
if (!pdev->bus)
|
|
goto error;
|
|
|
|
data = pci_get_drvdata(pdev);
|
|
|
|
btintel_pcie_disable_interrupts(data);
|
|
btintel_pcie_synchronize_irqs(data);
|
|
|
|
flush_work(&data->rx_work);
|
|
flush_work(&data->hdev->dump.dump_rx);
|
|
|
|
bt_dev_dbg(data->hdev, "Release bluetooth interface");
|
|
btintel_pcie_release_hdev(data);
|
|
|
|
err = pci_reset_function(pdev);
|
|
if (err) {
|
|
BT_ERR("Failed resetting the pcie device (%d)", err);
|
|
goto error;
|
|
}
|
|
|
|
btintel_pcie_enable_interrupts(data);
|
|
btintel_pcie_config_msix(data);
|
|
|
|
err = btintel_pcie_enable_bt(data);
|
|
if (err) {
|
|
BT_ERR("Failed to enable bluetooth hardware after reset (%d)",
|
|
err);
|
|
goto error;
|
|
}
|
|
|
|
btintel_pcie_reset_ia(data);
|
|
btintel_pcie_start_rx(data);
|
|
data->flags = 0;
|
|
|
|
err = btintel_pcie_setup_hdev(data);
|
|
if (err) {
|
|
BT_ERR("Failed registering hdev (%d)", err);
|
|
goto error;
|
|
}
|
|
error:
|
|
pci_dev_put(pdev);
|
|
pci_unlock_rescan_remove();
|
|
kfree(removal);
|
|
}
|
|
|
|
static void btintel_pcie_reset(struct hci_dev *hdev)
|
|
{
|
|
struct btintel_pcie_removal *removal;
|
|
struct btintel_pcie_data *data;
|
|
|
|
data = hci_get_drvdata(hdev);
|
|
|
|
if (!test_bit(BTINTEL_PCIE_SETUP_DONE, &data->flags))
|
|
return;
|
|
|
|
if (test_and_set_bit(BTINTEL_PCIE_RECOVERY_IN_PROGRESS, &data->flags))
|
|
return;
|
|
|
|
removal = kzalloc(sizeof(*removal), GFP_ATOMIC);
|
|
if (!removal)
|
|
return;
|
|
|
|
removal->pdev = data->pdev;
|
|
INIT_WORK(&removal->work, btintel_pcie_removal_work);
|
|
pci_dev_get(removal->pdev);
|
|
schedule_work(&removal->work);
|
|
}
|
|
|
|
static void btintel_pcie_hw_error(struct hci_dev *hdev, u8 code)
|
|
{
|
|
struct btintel_pcie_dev_recovery *data;
|
|
struct btintel_pcie_data *dev_data = hci_get_drvdata(hdev);
|
|
struct pci_dev *pdev = dev_data->pdev;
|
|
time64_t retry_window;
|
|
|
|
if (code == 0x13) {
|
|
bt_dev_err(hdev, "Encountered top exception");
|
|
return;
|
|
}
|
|
|
|
data = btintel_pcie_get_recovery(pdev, &hdev->dev);
|
|
if (!data)
|
|
return;
|
|
|
|
retry_window = ktime_get_boottime_seconds() - data->last_error;
|
|
|
|
if (retry_window < BTINTEL_PCIE_RESET_WINDOW_SECS &&
|
|
data->count >= BTINTEL_PCIE_FLR_MAX_RETRY) {
|
|
bt_dev_err(hdev, "Exhausted maximum: %d recovery attempts: %d",
|
|
BTINTEL_PCIE_FLR_MAX_RETRY, data->count);
|
|
bt_dev_dbg(hdev, "Boot time: %lld seconds",
|
|
ktime_get_boottime_seconds());
|
|
bt_dev_dbg(hdev, "last error at: %lld seconds",
|
|
data->last_error);
|
|
return;
|
|
}
|
|
btintel_pcie_inc_recovery_count(pdev, &hdev->dev);
|
|
btintel_pcie_reset(hdev);
|
|
}
|
|
|
|
static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
|
|
{
|
|
int err;
|
|
struct hci_dev *hdev;
|
|
|
|
hdev = hci_alloc_dev_priv(sizeof(struct btintel_data));
|
|
if (!hdev)
|
|
return -ENOMEM;
|
|
|
|
hdev->bus = HCI_PCI;
|
|
hci_set_drvdata(hdev, data);
|
|
|
|
data->hdev = hdev;
|
|
SET_HCIDEV_DEV(hdev, &data->pdev->dev);
|
|
|
|
hdev->manufacturer = 2;
|
|
hdev->open = btintel_pcie_open;
|
|
hdev->close = btintel_pcie_close;
|
|
hdev->send = btintel_pcie_send_frame;
|
|
hdev->setup = btintel_pcie_setup;
|
|
hdev->shutdown = btintel_shutdown_combined;
|
|
hdev->hw_error = btintel_pcie_hw_error;
|
|
hdev->set_diag = btintel_set_diag;
|
|
hdev->set_bdaddr = btintel_set_bdaddr;
|
|
hdev->reset = btintel_pcie_reset;
|
|
|
|
err = hci_register_dev(hdev);
|
|
if (err < 0) {
|
|
BT_ERR("Failed to register to hdev (%d)", err);
|
|
goto exit_error;
|
|
}
|
|
|
|
data->dmp_hdr.driver_name = KBUILD_MODNAME;
|
|
return 0;
|
|
|
|
exit_error:
|
|
hci_free_dev(hdev);
|
|
return err;
|
|
}
|
|
|
|
static int btintel_pcie_probe(struct pci_dev *pdev,
|
|
const struct pci_device_id *ent)
|
|
{
|
|
int err;
|
|
struct btintel_pcie_data *data;
|
|
|
|
if (!pdev)
|
|
return -ENODEV;
|
|
|
|
data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
|
|
if (!data)
|
|
return -ENOMEM;
|
|
|
|
data->pdev = pdev;
|
|
|
|
spin_lock_init(&data->irq_lock);
|
|
spin_lock_init(&data->hci_rx_lock);
|
|
|
|
init_waitqueue_head(&data->gp0_wait_q);
|
|
data->gp0_received = false;
|
|
|
|
init_waitqueue_head(&data->tx_wait_q);
|
|
data->tx_wait_done = false;
|
|
|
|
data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME, WQ_HIGHPRI);
|
|
if (!data->workqueue)
|
|
return -ENOMEM;
|
|
|
|
skb_queue_head_init(&data->rx_skb_q);
|
|
INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
|
|
|
|
data->boot_stage_cache = 0x00;
|
|
data->img_resp_cache = 0x00;
|
|
|
|
err = btintel_pcie_config_pcie(pdev, data);
|
|
if (err)
|
|
goto exit_error;
|
|
|
|
pci_set_drvdata(pdev, data);
|
|
|
|
err = btintel_pcie_alloc(data);
|
|
if (err)
|
|
goto exit_error;
|
|
|
|
err = btintel_pcie_enable_bt(data);
|
|
if (err)
|
|
goto exit_error;
|
|
|
|
/* CNV information (CNVi and CNVr) is in CSR */
|
|
data->cnvi = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_HW_REV_REG);
|
|
|
|
data->cnvr = btintel_pcie_rd_reg32(data, BTINTEL_PCIE_CSR_RF_ID_REG);
|
|
|
|
err = btintel_pcie_start_rx(data);
|
|
if (err)
|
|
goto exit_error;
|
|
|
|
err = btintel_pcie_setup_hdev(data);
|
|
if (err)
|
|
goto exit_error;
|
|
|
|
bt_dev_dbg(data->hdev, "cnvi: 0x%8.8x cnvr: 0x%8.8x", data->cnvi,
|
|
data->cnvr);
|
|
return 0;
|
|
|
|
exit_error:
|
|
/* reset device before exit */
|
|
btintel_pcie_reset_bt(data);
|
|
|
|
pci_clear_master(pdev);
|
|
|
|
pci_set_drvdata(pdev, NULL);
|
|
|
|
return err;
|
|
}
|
|
|
|
static void btintel_pcie_remove(struct pci_dev *pdev)
|
|
{
|
|
struct btintel_pcie_data *data;
|
|
|
|
data = pci_get_drvdata(pdev);
|
|
|
|
btintel_pcie_disable_interrupts(data);
|
|
|
|
btintel_pcie_synchronize_irqs(data);
|
|
|
|
flush_work(&data->rx_work);
|
|
|
|
btintel_pcie_reset_bt(data);
|
|
for (int i = 0; i < data->alloc_vecs; i++) {
|
|
struct msix_entry *msix_entry;
|
|
|
|
msix_entry = &data->msix_entries[i];
|
|
free_irq(msix_entry->vector, msix_entry);
|
|
}
|
|
|
|
pci_free_irq_vectors(pdev);
|
|
|
|
btintel_pcie_release_hdev(data);
|
|
|
|
destroy_workqueue(data->workqueue);
|
|
|
|
btintel_pcie_free(data);
|
|
|
|
pci_clear_master(pdev);
|
|
|
|
pci_set_drvdata(pdev, NULL);
|
|
}
|
|
|
|
#ifdef CONFIG_DEV_COREDUMP
|
|
static void btintel_pcie_coredump(struct device *dev)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(dev);
|
|
struct btintel_pcie_data *data = pci_get_drvdata(pdev);
|
|
|
|
if (test_and_set_bit(BTINTEL_PCIE_COREDUMP_INPROGRESS, &data->flags))
|
|
return;
|
|
|
|
data->dmp_hdr.trigger_reason = BTINTEL_PCIE_TRIGGER_REASON_USER_TRIGGER;
|
|
queue_work(data->workqueue, &data->rx_work);
|
|
}
|
|
#endif
|
|
|
|
static struct pci_driver btintel_pcie_driver = {
|
|
.name = KBUILD_MODNAME,
|
|
.id_table = btintel_pcie_table,
|
|
.probe = btintel_pcie_probe,
|
|
.remove = btintel_pcie_remove,
|
|
#ifdef CONFIG_DEV_COREDUMP
|
|
.driver.coredump = btintel_pcie_coredump
|
|
#endif
|
|
};
|
|
|
|
static int __init btintel_pcie_init(void)
|
|
{
|
|
return pci_register_driver(&btintel_pcie_driver);
|
|
}
|
|
|
|
static void __exit btintel_pcie_exit(void)
|
|
{
|
|
pci_unregister_driver(&btintel_pcie_driver);
|
|
btintel_pcie_free_restart_list();
|
|
}
|
|
|
|
module_init(btintel_pcie_init);
|
|
module_exit(btintel_pcie_exit);
|
|
|
|
MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
|
|
MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver " VERSION);
|
|
MODULE_VERSION(VERSION);
|
|
MODULE_LICENSE("GPL");
|