mirror of
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git
synced 2025-08-19 13:50:48 +00:00
46e828026c
net10 is connected to an SFP module. Unfortunately, the I2C lines are not connected due to an address conflict. Now that DPAA uses phylink, we can use in-band-status. This lets us determine whether the link is up or down instead of assuming it is up all the time. Also fix the phy mode while we're here. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
185 lines
2.9 KiB
Text
185 lines
2.9 KiB
Text
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
|
|
/*
|
|
* Device Tree Include file for Freescale Layerscape-1046A family SoC.
|
|
*
|
|
* Copyright 2016 Freescale Semiconductor, Inc.
|
|
* Copyright 2019-2020 NXP
|
|
*
|
|
* Mingkai Hu <mingkai.hu@nxp.com>
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "fsl-ls1046a.dtsi"
|
|
|
|
/ {
|
|
model = "LS1046A RDB Board";
|
|
compatible = "fsl,ls1046a-rdb", "fsl,ls1046a";
|
|
|
|
aliases {
|
|
serial0 = &duart0;
|
|
serial1 = &duart1;
|
|
serial2 = &duart2;
|
|
serial3 = &duart3;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
};
|
|
|
|
&duart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&duart1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&esdhc {
|
|
mmc-hs200-1_8v;
|
|
sd-uhs-sdr104;
|
|
sd-uhs-sdr50;
|
|
sd-uhs-sdr25;
|
|
sd-uhs-sdr12;
|
|
};
|
|
|
|
&i2c0 {
|
|
status = "okay";
|
|
|
|
ina220@40 {
|
|
compatible = "ti,ina220";
|
|
reg = <0x40>;
|
|
shunt-resistor = <1000>;
|
|
};
|
|
|
|
temp-sensor@4c {
|
|
compatible = "adi,adt7461";
|
|
reg = <0x4c>;
|
|
};
|
|
|
|
eeprom@52 {
|
|
compatible = "onnn,cat24c05", "atmel,24c04";
|
|
reg = <0x52>;
|
|
};
|
|
};
|
|
|
|
&i2c3 {
|
|
status = "okay";
|
|
|
|
rtc@51 {
|
|
compatible = "nxp,pcf2129";
|
|
reg = <0x51>;
|
|
/* IRQ_RTC_B -> IRQ05, active low */
|
|
interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>;
|
|
};
|
|
};
|
|
|
|
&ifc {
|
|
#address-cells = <2>;
|
|
#size-cells = <1>;
|
|
/* NAND Flashe and CPLD on board */
|
|
ranges = <0x0 0x0 0x0 0x7e800000 0x00010000
|
|
0x2 0x0 0x0 0x7fb00000 0x00000100>;
|
|
status = "okay";
|
|
|
|
nand@0,0 {
|
|
compatible = "fsl,ifc-nand";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
reg = <0x0 0x0 0x10000>;
|
|
};
|
|
|
|
cpld: board-control@2,0 {
|
|
compatible = "fsl,ls1046ardb-cpld";
|
|
reg = <0x2 0x0 0x0000100>;
|
|
};
|
|
};
|
|
|
|
&qspi {
|
|
status = "okay";
|
|
|
|
s25fs512s0: flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
spi-max-frequency = <50000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <1>;
|
|
reg = <0>;
|
|
};
|
|
|
|
s25fs512s1: flash@1 {
|
|
compatible = "jedec,spi-nor";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
spi-max-frequency = <50000000>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-tx-bus-width = <1>;
|
|
reg = <1>;
|
|
};
|
|
};
|
|
|
|
&usb1 {
|
|
dr_mode = "otg";
|
|
};
|
|
|
|
#include "fsl-ls1046-post.dtsi"
|
|
|
|
&fman0 {
|
|
ethernet@e4000 {
|
|
phy-handle = <&rgmii_phy1>;
|
|
phy-connection-type = "rgmii-id";
|
|
};
|
|
|
|
ethernet@e6000 {
|
|
phy-handle = <&rgmii_phy2>;
|
|
phy-connection-type = "rgmii-id";
|
|
};
|
|
|
|
ethernet@e8000 {
|
|
phy-handle = <&sgmii_phy1>;
|
|
phy-connection-type = "sgmii";
|
|
};
|
|
|
|
ethernet@ea000 {
|
|
phy-handle = <&sgmii_phy2>;
|
|
phy-connection-type = "sgmii";
|
|
};
|
|
|
|
ethernet@f0000 { /* 10GEC1 */
|
|
phy-handle = <&aqr106_phy>;
|
|
phy-connection-type = "xgmii";
|
|
};
|
|
|
|
ethernet@f2000 { /* 10GEC2 */
|
|
phy-connection-type = "10gbase-r";
|
|
managed = "in-band-status";
|
|
};
|
|
|
|
mdio@fc000 {
|
|
rgmii_phy1: ethernet-phy@1 {
|
|
reg = <0x1>;
|
|
};
|
|
|
|
rgmii_phy2: ethernet-phy@2 {
|
|
reg = <0x2>;
|
|
};
|
|
|
|
sgmii_phy1: ethernet-phy@3 {
|
|
reg = <0x3>;
|
|
};
|
|
|
|
sgmii_phy2: ethernet-phy@4 {
|
|
reg = <0x4>;
|
|
};
|
|
};
|
|
|
|
mdio@fd000 {
|
|
aqr106_phy: ethernet-phy@0 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
interrupts = <0 131 4>;
|
|
reg = <0x0>;
|
|
};
|
|
};
|
|
};
|