linux/Documentation/virt/hyperv/hibernation.rst

.. SPDX-License-Identifier: GPL-2.0

Hibernating Guest VMs
=====================

Background
----------
Linux supports the ability to hibernate itself in order to save power.
Hibernation is sometimes called suspend-to-disk, as it writes a memory
image to disk and puts the hardware into the lowest possible power
state. Upon resume from hibernation, the hardware is restarted and the
memory image is restored from disk so that it can resume execution
where it left off. See the "Hibernation" section of
Documentation/admin-guide/pm/sleep-states.rst.

Hibernation is usually done on devices with a single user, such as a
personal laptop. For example, the laptop goes into hibernation when
the cover is closed, and resumes when the cover is opened again.
Hibernation and resume happen on the same hardware, and Linux kernel
code orchestrating the hibernation steps assumes that the hardware
configuration is not changed while in the hibernated state.

Hibernation can be initiated within Linux by writing "disk" to
/sys/power/state or by invoking the reboot system call with the
appropriate arguments. This functionality may be wrapped by user space
commands such "systemctl hibernate" that are run directly from a
command line or in response to events such as the laptop lid closing.

Considerations for Guest VM Hibernation
---------------------------------------
Linux guests on Hyper-V can also be hibernated, in which case the
hardware is the virtual hardware provided by Hyper-V to the guest VM.
Only the targeted guest VM is hibernated, while other guest VMs and
the underlying Hyper-V host continue to run normally. While the
underlying Windows Hyper-V and physical hardware on which it is
running might also be hibernated using hibernation functionality in
the Windows host, host hibernation and its impact on guest VMs is not
in scope for this documentation.

Resuming a hibernated guest VM can be more challenging than with
physical hardware because VMs make it very easy to change the hardware
configuration between the hibernation and resume. Even when the resume
is done on the same VM that hibernated, the memory size might be
changed, or virtual NICs or SCSI controllers might be added or
removed. Virtual PCI devices assigned to the VM might be added or
removed. Most such changes cause the resume steps to fail, though
adding a new virtual NIC, SCSI controller, or vPCI device should work.

Additional complexity can ensue because the disks of the hibernated VM
can be moved to another newly created VM that otherwise has the same
virtual hardware configuration. While it is desirable for resume from
hibernation to succeed after such a move, there are challenges. See
details on this scenario and its limitations in the "Resuming on a
Different VM" section below.

Hyper-V also provides ways to move a VM from one Hyper-V host to
another. Hyper-V tries to ensure processor model and Hyper-V version
compatibility using VM Configuration Versions, and prevents moves to
a host that isn't compatible. Linux adapts to host and processor
differences by detecting them at boot time, but such detection is not
done when resuming execution in the hibernation image. If a VM is
hibernated on one host, then resumed on a host with a different processor
model or Hyper-V version, settings recorded in the hibernation image
may not match the new host. Because Linux does not detect such
mismatches when resuming the hibernation image, undefined behavior
and failures could result.


Enabling Guest VM Hibernation
-----------------------------
Hibernation of a Hyper-V guest VM is disabled by default because
hibernation is incompatible with memory hot-add, as provided by the
Hyper-V balloon driver. If hot-add is used and the VM hibernates, it
hibernates with more memory than it started with. But when the VM
resumes from hibernation, Hyper-V gives the VM only the originally
assigned memory, and the memory size mismatch causes resume to fail.

To enable a Hyper-V VM for hibernation, the Hyper-V administrator must
enable the ACPI virtual S4 sleep state in the ACPI configuration that
Hyper-V provides to the guest VM. Such enablement is accomplished by
modifying a WMI property of the VM, the steps for which are outside
the scope of this documentation but are available on the web.
Enablement is treated as the indicator that the administrator
prioritizes Linux hibernation in the VM over hot-add, so the Hyper-V
balloon driver in Linux disables hot-add. Enablement is indicated if
the contents of /sys/power/disk contains "platform" as an option. The
enablement is also visible in /sys/bus/vmbus/hibernation. See function
hv_is_hibernation_supported().

Linux supports ACPI sleep states on x86, but not on arm64. So Linux
guest VM hibernation is not available on Hyper-V for arm64.

Initiating Guest VM Hibernation
-------------------------------
Guest VMs can self-initiate hibernation using the standard Linux
methods of writing "disk" to /sys/power/state or the reboot system
call. As an additional layer, Linux guests on Hyper-V support the
"Shutdown" integration service, via which a Hyper-V administrator can
tell a Linux VM to hibernate using a command outside the VM. The
command generates a request to the Hyper-V shutdown driver in Linux,
which sends the uevent "EVENT=hibernate". See kernel functions
shutdown_onchannelcallback() and send_hibernate_uevent(). A udev rule
must be provided in the VM that handles this event and initiates
hibernation.

Handling VMBus Devices During Hibernation & Resume
--------------------------------------------------
The VMBus bus driver, and the individual VMBus device drivers,
implement suspend and resume functions that are called as part of the
Linux orchestration of hibernation and of resuming from hibernation.
The overall approach is to leave in place the data structures for the
primary VMBus channels and their associated Linux devices, such as
SCSI controllers and others, so that they are captured in the
hibernation image. This approach allows any state associated with the
device to be persisted across the hibernation/resume. When the VM
resumes, the devices are re-offered by Hyper-V and are connected to
the data structures that already exist in the resumed hibernation
image.

VMBus devices are identified by class and instance GUID. (See section
"VMBus device creation/deletion" in
Documentation/virt/hyperv/vmbus.rst.) Upon resume from hibernation,
the resume functions expect that the devices offered by Hyper-V have
the same class/instance GUIDs as the devices present at the time of
hibernation. Having the same class/instance GUIDs allows the offered
devices to be matched to the primary VMBus channel data structures in
the memory of the now resumed hibernation image. If any devices are
offered that don't match primary VMBus channel data structures that
already exist, they are processed normally as newly added devices. If
primary VMBus channels that exist in the resumed hibernation image are
not matched with a device offered in the resumed VM, the resume
sequence waits for 10 seconds, then proceeds. But the unmatched device
is likely to cause errors in the resumed VM.

When resuming existing primary VMBus channels, the newly offered
relids might be different because relids can change on each VM boot,
even if the VM configuration hasn't changed. The VMBus bus driver
resume function matches the class/instance GUIDs, and updates the
relids in case they have changed.

VMBus sub-channels are not persisted in the hibernation image. Each
VMBus device driver's suspend function must close any sub-channels
prior to hibernation. Closing a sub-channel causes Hyper-V to send a
RESCIND_CHANNELOFFER message, which Linux processes by freeing the
channel data structures so that all vestiges of the sub-channel are
removed. By contrast, primary channels are marked closed and their
ring buffers are freed, but Hyper-V does not send a rescind message,
so the channel data structure continues to exist. Upon resume, the
device driver's resume function re-allocates the ring buffer and
re-opens the existing channel. It then communicates with Hyper-V to
re-open sub-channels from scratch.

The Linux ends of Hyper-V sockets are forced closed at the time of
hibernation. The guest can't force closing the host end of the socket,
but any host-side actions on the host end will produce an error.

VMBus devices use the same suspend function for the "freeze" and the
"poweroff" phases, and the same resume function for the "thaw" and
"restore" phases. See the "Entering Hibernation" section of
Documentation/driver-api/pm/devices.rst for the sequencing of the
phases.

Detailed Hibernation Sequence
-----------------------------
1. The Linux power management (PM) subsystem prepares for
   hibernation by freezing user space processes and allocating
   memory to hold the hibernation image.
2. As part of the "freeze" phase, Linux PM calls the "suspend"
   function for each VMBus device in turn. As described above, this
   function removes sub-channels, and leaves the primary channel in
   a closed state.
3. Linux PM calls the "suspend" function for the VMBus bus, which
   closes any Hyper-V socket channels and unloads the top-level
   VMBus connection with the Hyper-V host.
4. Linux PM disables non-boot CPUs, creates the hibernation image in
   the previously allocated memory, then re-enables non-boot CPUs.
   The hibernation image contains the memory data structures for the
   closed primary channels, but no sub-channels.
5. As part of the "thaw" phase, Linux PM calls the "resume" function
   for the VMBus bus, which re-establishes the top-level VMBus
   connection and requests that Hyper-V re-offer the VMBus devices.
   As offers are received for the primary channels, the relids are
   updated as previously described.
6. Linux PM calls the "resume" function for each VMBus device. Each
   device re-opens its primary channel, and communicates with Hyper-V
   to re-establish sub-channels if appropriate. The sub-channels
   are re-created as new channels since they were previously removed
   entirely in Step 2.
7. With VMBus devices now working again, Linux PM writes the
   hibernation image from memory to disk.
8. Linux PM repeats Steps 2 and 3 above as part of the "poweroff"
   phase. VMBus channels are closed and the top-level VMBus
   connection is unloaded.
9. Linux PM disables non-boot CPUs, and then enters ACPI sleep state
   S4. Hibernation is now complete.

Detailed Resume Sequence
------------------------
1. The guest VM boots into a fresh Linux OS instance. During boot,
   the top-level VMBus connection is established, and synthetic
   devices are enabled. This happens via the normal paths that don't
   involve hibernation.
2. Linux PM hibernation code reads swap space is to find and read
   the hibernation image into memory. If there is no hibernation
   image, then this boot becomes a normal boot.
3. If this is a resume from hibernation, the "freeze" phase is used
   to shutdown VMBus devices and unload the top-level VMBus
   connection in the running fresh OS instance, just like Steps 2
   and 3 in the hibernation sequence.
4. Linux PM disables non-boot CPUs, and transfers control to the
   read-in hibernation image. In the now-running hibernation image,
   non-boot CPUs are restarted.
5. As part of the "resume" phase, Linux PM repeats Steps 5 and 6
   from the hibernation sequence. The top-level VMBus connection is
   re-established, and offers are received and matched to primary
   channels in the image. Relids are updated. VMBus device resume
   functions re-open primary channels and re-create sub-channels.
6. Linux PM exits the hibernation resume sequence and the VM is now
   running normally from the hibernation image.

Key-Value Pair (KVP) Pseudo-Device Anomalies
--------------------------------------------
The VMBus KVP device behaves differently from other pseudo-devices
offered by Hyper-V.  When the KVP primary channel is closed, Hyper-V
sends a rescind message, which causes all vestiges of the device to be
removed. But Hyper-V then re-offers the device, causing it to be newly
re-created. The removal and re-creation occurs during the "freeze"
phase of hibernation, so the hibernation image contains the re-created
KVP device. Similar behavior occurs during the "freeze" phase of the
resume sequence while still in the fresh OS instance. But in both
cases, the top-level VMBus connection is subsequently unloaded, which
causes the device to be discarded on the Hyper-V side. So no harm is
done and everything still works.

Virtual PCI devices
-------------------
Virtual PCI devices are physical PCI devices that are mapped directly
into the VM's physical address space so the VM can interact directly
with the hardware. vPCI devices include those accessed via what Hyper-V
calls "Discrete Device Assignment" (DDA), as well as SR-IOV NIC
Virtual Functions (VF) devices. See Documentation/virt/hyperv/vpci.rst.

Hyper-V DDA devices are offered to guest VMs after the top-level VMBus
connection is established, just like VMBus synthetic devices. They are
statically assigned to the VM, and their instance GUIDs don't change
unless the Hyper-V administrator makes changes to the configuration.
DDA devices are represented in Linux as virtual PCI devices that have
a VMBus identity as well as a PCI identity. Consequently, Linux guest
hibernation first handles DDA devices as VMBus devices in order to
manage the VMBus channel. But then they are also handled as PCI
devices using the hibernation functions implemented by their native
PCI driver.

SR-IOV NIC VFs also have a VMBus identity as well as a PCI
identity, and overall are processed similarly to DDA devices. A
difference is that VFs are not offered to the VM during initial boot
of the VM. Instead, the VMBus synthetic NIC driver first starts
operating and communicates to Hyper-V that it is prepared to accept a
VF, and then the VF offer is made. However, the VMBus connection
might later be unloaded and then re-established without the VM being
rebooted, as happens in Steps 3 and 5 in the Detailed Hibernation
Sequence above and in the Detailed Resume Sequence. In such a case,
the VFs likely became part of the VM during initial boot, so when the
VMBus connection is re-established, the VFs are offered on the
re-established connection without intervention by the synthetic NIC driver.

UIO Devices
-----------
A VMBus device can be exposed to user space using the Hyper-V UIO
driver (uio_hv_generic.c) so that a user space driver can control and
operate the device. However, the VMBus UIO driver does not support the
suspend and resume operations needed for hibernation. If a VMBus
device is configured to use the UIO driver, hibernating the VM fails
and Linux continues to run normally. The most common use of the Hyper-V
UIO driver is for DPDK networking, but there are other uses as well.

Resuming on a Different VM
--------------------------
This scenario occurs in the Azure public cloud in that a hibernated
customer VM only exists as saved configuration and disks -- the VM no
longer exists on any Hyper-V host. When the customer VM is resumed, a
new Hyper-V VM with identical configuration is created, likely on a
different Hyper-V host. That new Hyper-V VM becomes the resumed
customer VM, and the steps the Linux kernel takes to resume from the
hibernation image must work in that new VM.

While the disks and their contents are preserved from the original VM,
the Hyper-V-provided VMBus instance GUIDs of the disk controllers and
other synthetic devices would typically be different. The difference
would cause the resume from hibernation to fail, so several things are
done to solve this problem:

* For VMBus synthetic devices that support only a single instance,
  Hyper-V always assigns the same instance GUIDs. For example, the
  Hyper-V mouse, the shutdown pseudo-device, the time sync pseudo
  device, etc., always have the same instance GUID, both for local
  Hyper-V installs as well as in the Azure cloud.

* VMBus synthetic SCSI controllers may have multiple instances in a
  VM, and in the general case instance GUIDs vary from VM to VM.
  However, Azure VMs always have exactly two synthetic SCSI
  controllers, and Azure code overrides the normal Hyper-V behavior
  so these controllers are always assigned the same two instance
  GUIDs. Consequently, when a customer VM is resumed on a newly
  created VM, the instance GUIDs match. But this guarantee does not
  hold for local Hyper-V installs.

* Similarly, VMBus synthetic NICs may have multiple instances in a
  VM, and the instance GUIDs vary from VM to VM. Again, Azure code
  overrides the normal Hyper-V behavior so that the instance GUID
  of a synthetic NIC in a customer VM does not change, even if the
  customer VM is deallocated or hibernated, and then re-constituted
  on a newly created VM. As with SCSI controllers, this behavior
  does not hold for local Hyper-V installs.

* vPCI devices do not have the same instance GUIDs when resuming
  from hibernation on a newly created VM. Consequently, Azure does
  not support hibernation for VMs that have DDA devices such as
  NVMe controllers or GPUs. For SR-IOV NIC VFs, Azure removes the
  VF from the VM before it hibernates so that the hibernation image
  does not contain a VF device. When the VM is resumed it
  instantiates a new VF, rather than trying to match against a VF
  that is present in the hibernation image. Because Azure must
  remove any VFs before initiating hibernation, Azure VM
  hibernation must be initiated externally from the Azure Portal or
  Azure CLI, which in turn uses the Shutdown integration service to
  tell Linux to do the hibernation. If hibernation is self-initiated
  within the Azure VM, VFs remain in the hibernation image, and are
  not resumed properly.

In summary, Azure takes special actions to remove VFs and to ensure
that VMBus device instance GUIDs match on a new/different VM, allowing
hibernation to work for most general-purpose Azure VMs sizes. While
similar special actions could be taken when resuming on a different VM
on a local Hyper-V install, orchestrating such actions is not provided
out-of-the-box by local Hyper-V and so requires custom scripting.