Mark of the Unicorn designed Track 16 2011 as one of models in third
generation of its FireWire series. The model is already discontinued.
It consists of below ICs:
* Texas Instruments TSB41AB1
* Microchip (SMSC) USB3300
* Xilinx Spartan-3A FPGA, XC3S700A
* Texas Instruments TMS320C6722
* Microchip (Atmel) AT91SAM SAM7S512
It supports sampling transfer frequency up to 192.0 kHz. The packet
format differs depending on both of current sampling transfer frequency
and the type of signal in optical interfaces. The model supports
transmission of PCM frames as well as MIDI messages.
The model supports command mechanism to configure internal DSP. Hardware
meter information is available in the first 2 chunks of each data block
of tx packet.
This commit adds support for it.
$ cd linux-firewire-tools/src
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 04107d95 bus_info_length 4, crc_length 16, crc 32149
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 000a83c4 device_id 00000a83c4 | EUI-64 0001f200000a83c4
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 00035b04 directory_length 3, crc 23300
42c 120001f2 specifier id
430 13000039 version
434 17102800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 0002b25f leaf_length 2, crc 45663
43c 0001f200 company_id 0001f2 |
440 000a83c4 device_id 00000a83c4 | EUI-64 0001f200000a83c4
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211107110644.23511-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mark of the Unicorn (MOTU) shipped Traveler mk3 as one of models in third
generation of its FireWire series, and discontinued it already. The model
consists of below ICs:
* Texas Instruments TSB41AB2
* Phillips Semiconductors PDI1394L40
* Altera cyclone EP1C3
* Texas Instruments TMS320VC5402
It supports sampling transfer frequency up to 192.0 kHz. The packet
format differs depending on both of current sampling transfer frequency
and whether to enable ADAT channels in rx/tx packets. The model supports
transmission of PCM frames as well as MIDI messages.
The model supports command mechanism to configure internal DSP. Hardware
meter information is available in the first 2 chunks of each data block
of tx packet.
This commit adds support for it.
$ cd linux-firewire-tools/src
$ python crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 0410af0a bus_info_length 4, crc_length 16, crc 44810
404 31333934 bus_name "1394"
408 20ff7000 irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c 0001f200 company_id 0001f2 |
410 00090911 device_id 0000090911 | EUI-64 0001f20000090911
root directory
-----------------------------------------------------------------
414 0004ef04 directory_length 4, crc 61188
418 030001f2 vendor
41c 0c0083c0 node capabilities per IEEE 1394
420 d1000002 --> unit directory at 428
424 8d000005 --> eui-64 leaf at 438
unit directory at 428
-----------------------------------------------------------------
428 00031733 directory_length 3, crc 5939
42c 120001f2 specifier id
430 1300001b version
434 17102800 model
eui-64 leaf at 438
-----------------------------------------------------------------
438 00028484 leaf_length 2, crc 33924
43c 0001f200 company_id 0001f2 |
440 00090911 device_id 0000090911 | EUI-64 0001f20000090911
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211104110627.94469-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of MOTU models allows software to configure their DSP parameters by
command included in asynchronous transaction. The models multiplex messages
for hardware meters into isochronous packet as well as PCM frames. For
convenience, I call them as 'command DSP' model.
This patch adds message parser for them to gather hardware meter
information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211015080826.34847-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some of MOTU models allows software to configure their DSP parameters by
accessing to their registers. The models multiplex messages for status of
DSP into isochronous packet as well as PCM frames. The message includes
information of hardware metering, MIDI message, current parameters of DSP.
For my convenience, I call them as 'register DSP' model.
This patch adds message parser for them to gather hardware meter
information.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20211015080826.34847-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current implementation of driver has two similar helper functions for
source detection of sampling clock. This commit merges them as a code
refactoring.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210623075941.72562-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I assumed that the combination of packet formats for MOTU 828 mk3 Hybrid
is the same as MOTU 828 mk3 FireWire. However at higher sampling rate, it
is different. MOTU 828 mk3 Hybrid has additional 4 dummy data chunks for
rx packet.
This commit fixes the issue to which I address at a commit f2ac3b8395
("ALSA: firewire-motu: sequence replay for source packet header").
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210618040713.114611-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It costs expensive to change clock configuration for models of protocol
version 3. In current implementation, speculative strategy is used to
finish the operation; just waiting for 4 seconds. As long as I investigate,
when accepting and changing clock status actually, the device sends
notification with mask.
This commit uses wise way to wait for the notification after changing
sampling clock rate during 4 seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200614141221.53527-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit splits the method to get clock source for protocol
version 3 so that model-dependent operations are explicitly defined.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200519111641.123211-14-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds alternative functions to detect packet format so that
each function corresponds to each model.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200519111641.123211-9-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU protocol, data block consists of SPH and 24-bit chunks
aligned to quadlet. The number of chunks per data block is specific
to model. For models with optical interface, the number differs
depending on I/O settings for the interface (ADAT, TOSLINK).
Currently the number is calculated from flags in model-specific
data. However this is weak in the case that the model has quirks.
Actually, for quirks of some models, flags are used against their
original meanings.
This commit adds model-specific table of chunk count. For future
integration, this table is based on the calculation.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200519111641.123211-7-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The most of members in spec data is used in each protocol file. It's
better to capsulate the data to the file.
This commit moves the data to the file for protocol version 3.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20200519111641.123211-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In MOTU FireWire series, devices have a mode to generate sampling clock
from a sequence of source packet header (SPH) included in each data block
of received packet. This mode is used for several purposes such as mode
for SMPTE time code, sync to the other sound cards and so on.
This commit adds support for the SPH mode.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191030080644.1704-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MOTU Traveler supports AES/EBU on XLR interface and data block of rx/tx
packet includes two chunk for the interface. This commit adds a flag
for this purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver explicitly assumes that all of supported models have main data
chunk separated from chunk for analog ports. However, MOTU Traveler doesn't
support the separated main data chunk.
This commit adds a flag for the separated main data chunk.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocols of MOTU FireWire series, when transferring MIDI messages,
transmitter set existence flag to one byte on first several quadlets. The
position differs depending on protocols and models, however two cases are
confirmed; in 5th byte and 8th byte from MSB side.
This commit adds a series of specification flag to describe them. When
the existence flag is in the 5th byte, SND_MOTU_SPEC_[R|T]X_MIDI_2ND_Q is
used. Else, another set of the flag is used. Here, '_Q' means quadlet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In protocol version 3, drivers can read current sampling clock status from
register 0x'ffff'f000'0b14. 8 bits of LSB of this register represents type
of signal as source of clock.
Current driver code includes invalid bitshift to handle the parameter. This
commit fixes the bug.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 5992e30034 ("ALSA: firewire-motu: add support for MOTU 828mk3 (FireWire/Hybrid) as a model with protocol version 3")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MOTU 828mk3 (FireWire/Hybrid) is one of third generation in MOTU FireWire
series, produced in 2008/2014. This model consists of three chips for
functionality on IEEE 1394 bus:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* Xilinx Spartan-3E FPGA Family (Link layer for IEEE 1394 bus, packet
processing and data block processing layer)
* TI TMS320C6722 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 3. This protocol has some additional features to protocol
version 2.
* Support several optical interfaces.
* Support a data chunk for return of reverb effect.
* Have a quirk of tx packets.
* Support heartbeat asynchronous transaction.
In this protocol, series of transferred packets has some quirks. Below
fields in CIP headers of the packets are out of IEC 61883-1:
- SID (source node id): always 0x0d
- DBS (data block size): always 0x04
- DBC (data block counter): always 0x00
- EOH (End of header): always 0x00
Below is an actual sample of transferred packets.
quads CIP1 CIP2
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
520 0x0D040400 0x22FFFFFF
8 0x0D040400 0x22FFFFFF
Status of clock is configured by write transactions to 0x'ffff'f000'0b14,
as well as version 2, while meanings of fields are different from the
former protocols. Modes of optical interfaces are configured by write
transactions to 0x'ffff'f000'0c94.
Drivers can register its address to receive heatbeat transactions from the
unit. 0x'ffff'f000'0b0c is for the higher part and 0x'ffff'f000'0b10 is
for the lower part. Nevertheless, this feature is not useless for this
driver and this commit omits it.
Each data block consists of two parts in a point of the number of included
data chunks. In both of 'fixed' and 'differed' parts, the number of
included data blocks are a multiple of 4, thus depending on models there's
some empty data chunks. For example, 828mk3 includes one pair of empty
data chunks in its fixed part. When optical interface is configured to
S/PDIF, 828mk3 includes one pair of empty data chunks in its differed part.
To reduce consumption of CPU cycles with additional conditions/loops, this
commit just exposes these empty chunks to user space as PCM channels.
Additionally, 828mk3 has a non-negligible overhead to change its sampling
transfer frequency. When softwares send asynchronous transaction to
perform it, LED on the unit starts to blink. In a worst case, it continues
blink during several seconds; e.g. 10 seconds. When stopping blinking,
the unit seems to be prepared for the requested sampling transfer
frequency. To wait for the preparation, this commit forces the driver
to call task scheduler and applications sleeps for 4 seconds.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
