Hugh Dickins found that characters in xterm were going missing and oft
delayed. Being the curious type, he managed to associate this with the
new high-precision vblank patches; disabling these he found, restored
the orderliness of his characters.
The oddness begins when one realised that Hugh was not using vblanks at
all on his system (fvwm and some xterms). Instead, all he had to go on
were warning of a pipe underrun, curiously enough at around 60Hz. He
poked and found that in addition to the underrun warning, the hardware
was flagging the start of a new frame, a vblank, which in turn was
kicking off the pending vblank processing code.
There is little we can do for the underruns on Hugh's machine, a
Crestline [965GM], which must have its FIFO watermarks set to 8.
However, we do not need to process the vblank if we know that they are
disabled...
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Instead of reporting EIO upfront in the entrance of an ioctl that may or
may not attempt to use the GPU, defer the actual detection of an invalid
ioctl to when we issue a GPU instruction. This allows us to continue to
use bo in video memory (via pread/pwrite and mmap) after the GPU has hung.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Based on a patch by Takashi Iwai.
Reported-by: Matthias Hopf <mat@mshopf.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=27272
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon resume, like after a cold boot, we need to forcibly probe the
analog connector and cannot rely on the hotplug status.
Based on a patch by Takashi Iwai.
Reported-by: Stefan Dirsch <sndirsch@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=26952
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Call drm_mode_config_reset() after an invalidation event to restore any
cached state to unknown.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We were not pausing after detecting the response was pending and so did
not allow the hardware sufficient time to complete before aborting. This
lead to transient failures whilst probing SDVO devices.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30235
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Rather than power cycling the panel when there are no bits to display,
use the VDD AUX bit to power the panel up just enough for DP AUX
transactions to work. This prevents a bit of unnecessary ugliness as
mode sets occur on the panel.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Now that we're doing the right thing elsewhere, these are no longer
necessary.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=31114
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move the plane->mode config to the point of use rather than repeatedly
querying the same information.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
error_bo and pinned_bo could be used uninitialised if there were no
active buffers.
Caught by kmemcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The opregion is a shared memory region between ACPI and the graphics
driver. As the ACPI mapping has been changed to cachable in commit
6d5bbf00d2, mapping the intel opregion
non-cachable now fails. As no bus-master hardware is involved in the
opregion, cachable map should do no harm.
Tested on a Fujitsu Lifebook P8010.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
[ickle: convert to acpi_os_ioremap for consistency]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If the driver calls into the kernel to wait for a breadcrumb to pass,
but hasn't enabled interrupts, fallback to polling the breadcrumb value.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We only have sufficient information for accurate (sub-frame) timestamping
when the modesetting is under our control.
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We can only utilize the stolen portion of the GTT if we are in sole
charge of the hardware. This is only true if using GEM and KMS,
otherwise VESA continues to access stolen memory.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Starting with SandyBridge (though possible with earlier hacked BIOSes),
the BIOS may initialise the IGFX as secondary to a discrete GPU. Prior,
it would simply disable the integrated GPU. So we adjust our PCI class
mask to match any DISPLAY_CLASS device.
In such a configuration, the IGFX is not a primary VGA controller and
so should not take part in VGA arbitration, and the error return from
vga_client_register() is expected.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
There are I915_NUM_RINGS-1 inter-ring synchronisation counters, but we
were clearing I915_NUM_RINGS of them. Oops.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Tested-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
During suspend, Linus found that his machine would hang for 3 seconds,
and identified that intel_ring_buffer_wait() was the culprit:
"Because from looking at the code, I get the notion that
"intel_read_status_page()" may not be exact. But what happens if that
inexact value matches our cached ring->actual_head, so we never even
try to read the exact case? Does it _stay_ inexact for arbitrarily
long times? If so, we might wait for the ring to empty forever (well,
until the timeout - the behavior I see), even though the ring really
_is_ empty."
As the reported HEAD position is only updated every time it crosses a
64k boundary, whilst draining the ring it is indeed likely to remain one
value. If that value matches the last known HEAD position, we never read
the true value from the register and so trigger a timeout.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Hangcheck and error recovery is only used by GEM.
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
For CRT and SDVO/HDMI, we need to use a normal, non-SSC, clock and so we
must clear any enabling bits left-over from earlier outputs. And also
seems to correct the LVDS panel on the Lenovo U160.
However, at one point, it did cause an "ERROR failed to disable
trancoder". So prolonged testing on top of Jesse's refactored and
error-checking CRTC logic is desired.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup.
If these are not correct then although the panel looks ok, output from an
HDMI encoder (eg, Chrontel CH7036) will be incorrect.
Signed-off-by: Mark Hayter <mdhayter@chromium.org>
[ickle: minor adjustments]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The i915 driver normally assumes the video bios has configured several
of the LVDS panel registers, and it just inherits the values. If the
vbios has not run, several of these will need to be setup. So we need to
check that the LVDS sync polarity is correctly configured per any
available modelines (e.g. EDID) and adjust if not, issuing a warning as
we do.
Signed-off-by: Mark Hayter <mdhayter@chromium.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These make us increase our frequency much more readily, and decrease
them only after significant idle time, resulting in a 20% performance
increase for nexuiz.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Move code around and invoke iomem annotation in a few more places in
order to silence sparse. Still a few more iomem annotations to go...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
I changed 945's self refresh to work without the need for the driver to
enable/disable self refresh manually based on the idle state of the gpu.
This is much better than enabling/disabling self refresh for various
reasons, including staying in a lower power state for more time and
avoiding the need for cpu cycles.
This was originally done manually to workaround issues with the hardware
hanging. However, since 944001201: drm/i915: enable low power render
writes on GEN3 hardware, automatic CxSR seems stable.
Signed-off-by: Alexander Lam <lambchop468@gmail.com>
Acked-by : Li Peng <peng.li@linux.intel.com>
[ickle: play safe with the ordering and disable CxSR before tweaking any
watermark and enable afterwards.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
945 class hardware has an interesting quirk in which the vblank
interrupt is not raised if the CPU is in a low power state. (We also
suspect that the memory bus is clocked to the CPU/c-state and not the
GPU so there are secondary starvation issues.) In order to prevent the
most obvious issue of the low of the vblank interrupt (stuttering
compositing that only updates when the mouse is moving) is to install a
PM QoS request to prevent low c-states whilst the GPU is active.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
eDP on the CPU doesn't need the PCH set up at all, it can in fact cause
problems. So avoid FDI training and PCH PLL enabling in that case.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We need to unlock the phase sync pointer enable bit before we can
actually enable the phase sync pointer workaround on Ironlake.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Factor out the FDI disable function (make it a mirror of
ironlake_fdi_enable) and add some FDI related assertions to the FDI
training code (we need an active pipe & plane before we start
transmitting bits).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Along with assertion checks for the FDI transmitters and receivers
(including PLLs). Modify the pipe enable function to check for FDI PLL
status as well, when driving PCH ports.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Otherwise our writes will be silently ignored.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With assertions to check transcoder and reference clock state.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
For pre-ILK only. Saves some code in the CRTC enable/disable functions
and allows us to check for pipe and panel status at enable/disable time.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
When PLLs or timing regs are changed, we need to make sure the panel
lock will allow it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Add plane enable/disable functions to prevent duplicated code and allow
us to easily check for plane enable/disable requirements (such as pipe
enable, plane status, pll status etc).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On Ironlake+ we need to enable these in a specific order.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Admittedly, trusting ACPI or the BIOS at all to be correct is littered
with numerous examples where it is wrong. Maybe, just maybe, we will
have better luck using the ACPI OpRegion lid status...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Without this change, blits to the front buffer won't invalidate FBC
state, causing us to scan out stale data. Make sure we update these
bits on every FBC enable, since they may get clobbered if we shut off
the display.
References: https://bugzilla.kernel.org/show_bug.cgi?id=26932
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
