Freshly introduced NEGOTIATE_PROTOCOL_VERSION allows the agent to ascertain
upfront if a specific protocol(usually older) version is supported by the
platform.
It is used by the agent in case the platform has advertised the support of
a newer protocol version than the latest version supported by the agent,
since backward compatibility cannot be automatically assumed.
Emit a warning about possible incompatibility when negotiation was not
possible or just print the successfully negotiated protocol.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240214183006.3403207-3-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fix the kernel-doc notation for the nested union in struct
scmi_optee_channel to eliminate kernel-doc warnings:
| optee.c:130: warning: Excess struct member 'shmem' description
| in 'scmi_optee_channel'
| optee.c:131: warning: Function parameter or struct member 'req'
| not described in 'scmi_optee_channel'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240221062157.8694-1-rdunlap@infradead.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Extend the perf notification report to include pre-calculated frequencies
corresponding to the reported limits/levels event; such frequencies are
properly computed based on the stored known OPPs information taking into
consideration if the current operating mode is level indexed or not.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-12-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Store all the discovered OPPs into the XArray opps_by_lvl even when
level_indexing mode is not used, since it comes handy to easily retrieve
OPPs by level.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-11-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the powercap protocol related notify
enable commands are supported at all by the SCMI platform, and then
provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain
supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-10-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the reset protocol related notify
enable commands are supported at all by the SCMI platform, and then
provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain
supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-9-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the sensor protocol related notify
enable commands are supported at all by the SCMI platform, and then
provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain
supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-8-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the clock protocol related notify
enable commands are supported at all by the SCMI platform, and then
provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain
supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-7-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the system power protocol related
notify enable commands are supported at all by the SCMI platform, and
then provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain supports
notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-6-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the power related notify enable
commands are supported at all by the SCMI platform, and then provide
the callback needed to allow the core SCMI notification subsytem to do
a fine-grain check if a specific resource domain supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-5-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add a preliminary check to verify if the performance related notify
enable commands are supported at all by the SCMI platform, and then
provide the callback needed to allow the core SCMI notification
subsytem to do a fine-grain check if a specific resource domain
supports notifications.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-4-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When registering protocol events, use the optional .is_notify_supported
callback provided by the protocol to check if that specific notification
type is available for that particular resource on the running system,
marking it as unsupported otherwise.
Then, when a notification enable request is received, return an error if
it was previously marked as unsuppported, so avoiding to send a needless
notification enable command and check the returned value for failure.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240212123233.1230090-2-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Now that the driver core can properly handle constant struct bus_type,
move the scmi_bus_type variable to be a constant structure as well,
placing it into read-only memory which can not be modified at runtime.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20240211-bus_cleanup-firmware2-v1-2-1851c92c7be7@marliere.net
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When the generic SCMI code tears down a channel, it calls the chan_free
callback function, defined by each transport. Since multiple protocols
might share the same transport_info member, chan_free() might want to
clean up the same member multiple times within the given SCMI transport
implementation. In this case, it is SMC transport. This will lead to a NULL
pointer dereference at the second time:
| scmi_protocol scmi_dev.1: Enabled polling mode TX channel - prot_id:16
| arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
| arm-scmi firmware:scmi: unable to communicate with SCMI
| Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
| Mem abort info:
| ESR = 0x0000000096000004
| EC = 0x25: DABT (current EL), IL = 32 bits
| SET = 0, FnV = 0
| EA = 0, S1PTW = 0
| FSC = 0x04: level 0 translation fault
| Data abort info:
| ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
| CM = 0, WnR = 0, TnD = 0, TagAccess = 0
| GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
| user pgtable: 4k pages, 48-bit VAs, pgdp=0000000881ef8000
| [0000000000000000] pgd=0000000000000000, p4d=0000000000000000
| Internal error: Oops: 0000000096000004 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 4 PID: 1 Comm: swapper/0 Not tainted 6.7.0-rc2-00124-g455ef3d016c9-dirty #793
| Hardware name: FVP Base RevC (DT)
| pstate: 61400009 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
| pc : smc_chan_free+0x3c/0x6c
| lr : smc_chan_free+0x3c/0x6c
| Call trace:
| smc_chan_free+0x3c/0x6c
| idr_for_each+0x68/0xf8
| scmi_cleanup_channels.isra.0+0x2c/0x58
| scmi_probe+0x434/0x734
| platform_probe+0x68/0xd8
| really_probe+0x110/0x27c
| __driver_probe_device+0x78/0x12c
| driver_probe_device+0x3c/0x118
| __driver_attach+0x74/0x128
| bus_for_each_dev+0x78/0xe0
| driver_attach+0x24/0x30
| bus_add_driver+0xe4/0x1e8
| driver_register+0x60/0x128
| __platform_driver_register+0x28/0x34
| scmi_driver_init+0x84/0xc0
| do_one_initcall+0x78/0x33c
| kernel_init_freeable+0x2b8/0x51c
| kernel_init+0x24/0x130
| ret_from_fork+0x10/0x20
| Code: f0004701 910a0021 aa1403e5 97b91c70 (b9400280)
| ---[ end trace 0000000000000000 ]---
Simply check for the struct pointer being NULL before trying to access
its members, to avoid this situation.
This was found when a transport doesn't really work (for instance no SMC
service), the probe routines then tries to clean up, and triggers a crash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Fixes: 1dc6558062 ("firmware: arm_scmi: Add smc/hvc transport")
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240126122325.2039669-1-andre.przywara@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
ARM SCMI v3.2 introduces clock get permission command. To implement the
same let us stash the values of those permissions in the scmi_clock_info.
They indicate if the operation is forbidden or not.
If the CLOCK_GET_PERMISSIONS command is not supported, the default
permissions are set to allow the operations, otherwise they will be set
according to the response of CLOCK_GET_PERMISSIONS from the SCMI
platform firmware.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20240121110901.1414856-1-peng.fan@oss.nxp.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the capability for a SCMI driver to register to the core SCMI stack
with multiple SCMI protocols. In such a case the SCMI driver probe
function will end up being called once for each registered protocol
which have been also found as implemented on the platform.
This is especially useful in testing scenarios.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231221151129.325749-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Accessing clock domains descriptors by the index from the SCMI drivers
can potentially lead to out-of-bound violations if the SCMI drivers
misbehaves.
Use a common helper to check the consistency of such accesses.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240110120916.2482603-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When (sustained_freq_khz * 1000) is less than sustained_perf_level, the
multiplier will be less than 1 and hence rounded down as 0. Similarly if
it is not multiple of sustained_perf_level the dom_info->mult_factor will
contain rounded down value and will end up impacting all the frequency
calculations done using it.
Add warning if and when the domain frequency multiplier is 0 or rounded
down so that it gives a clue to get the firmware tables fixed.
Suggested-by: Pierre Gondois <Pierre.Gondois@arm.com>
Reviewed-by: Pierre Gondois <pierre.gondois@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240119152338.3047620-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Rollback currently supported SCMI clock protocol version to v2.0 since
some of the mandatory v3.0 features are indeed still not supported yet.
Fixes: b5efc28a75 ("firmware: arm_scmi: Add protocol versioning checks")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240109181716.2338636-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The clock protocol version as per the SCMI v3.2 specification is 0x30000.
Enable the v3.0 clock protocol features only when clock protocol version
equals 0x30000.
The previous beta version of the spec had this value set to 0x20001 and
th same value trickled down from the initial development. The version
update were missed in the driver.
Fixes: e49e314a2c ("firmware: arm_scmi: Add clock v3.2 CONFIG_SET support")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240109150106.2066739-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
When storing opps by level or index use xa_insert() instead of xa_store()
and add error-checking to spot bad duplicates indexes possibly wrongly
provided by the platform firmware.
Fixes: 31c7c1397a ("firmware: arm_scmi: Add v3.2 perf level indexing mode support")
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20240108185050.1628687-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
linux/bug.h includes asm-generic/bug.h already and hence replacing
asm-generic/bug.h with linux/bug.h will not regress any build.
Also, it is always better to avoid header file inclusion from asm-generic
if possible.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tanzir Hasan <tanzirh@google.com>
Link: https://lore.kernel.org/r/20231226-shmem-v1-1-ea15ce81d8ba@google.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
On reception of a completion interrupt the shared memory area is accessed
to retrieve the message header at first and then, if the message sequence
number identifies a transaction which is still pending, the related
payload is fetched too.
When an SCMI command times out the channel ownership remains with the
platform until eventually a late reply is received and, as a consequence,
any further transmission attempt remains pending, waiting for the channel
to be relinquished by the platform.
Once that late reply is received the channel ownership is given back
to the agent and any pending request is then allowed to proceed and
overwrite the SMT area of the just delivered late reply; then the wait
for the reply to the new request starts.
It has been observed that the spurious IRQ related to the late reply can
be wrongly associated with the freshly enqueued request: when that happens
the SCMI stack in-flight lookup procedure is fooled by the fact that the
message header now present in the SMT area is related to the new pending
transaction, even though the real reply has still to arrive.
This race-condition on the A2P channel can be detected by looking at the
channel status bits: a genuine reply from the platform will have set the
channel free bit before triggering the completion IRQ.
Add a consistency check to validate such condition in the A2P ISR.
Reported-by: Xinglong Yang <xinglong.yang@cixtech.com>
Closes: https://lore.kernel.org/all/PUZPR06MB54981E6FA00D82BFDBB864FBF08DA@PUZPR06MB5498.apcprd06.prod.outlook.com/
Fixes: 5c8a47a5a9 ("firmware: arm_scmi: Make scmi core independent of the transport type")
Cc: stable@vger.kernel.org # 5.15+
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Xinglong Yang <xinglong.yang@cixtech.com>
Link: https://lore.kernel.org/r/20231220172112.763539-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Here is the big set of char/misc and other driver subsystem changes for
6.8-rc1. Lots of stuff in here, but first off, you will get a merge
conflict in drivers/android/binder_alloc.c when merging this tree due to
changing coming in through the -mm tree.
The resolution of the merge issue can be found here:
https://lore.kernel.org/r/20231207134213.25631ae9@canb.auug.org.au
or in a simpler patch form in that thread:
https://lore.kernel.org/r/ZXHzooF07LfQQYiE@google.com
If there are issues with the merge of this file, please let me know.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported issues
(other than the binder merge conflict.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZaeMMQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynWNgCfQ/Yz7QO6EMLDwHO5LRsb3YMhjL4AoNVdanjP
YoI7f1I4GBcC0GKNfK6s
=+Kyv
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem changes
for 6.8-rc1.
Other than lots of binder driver changes (as you can see by the merge
conflicts) included in here are:
- lots of iio driver updates and additions
- spmi driver updates
- eeprom driver updates
- firmware driver updates
- ocxl driver updates
- mhi driver updates
- w1 driver updates
- nvmem driver updates
- coresight driver updates
- platform driver remove callback api changes
- tags.sh script updates
- bus_type constant marking cleanups
- lots of other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (341 commits)
android: removed duplicate linux/errno
uio: Fix use-after-free in uio_open
drivers: soc: xilinx: add check for platform
firmware: xilinx: Export function to use in other module
scripts/tags.sh: remove find_sources
scripts/tags.sh: use -n to test archinclude
scripts/tags.sh: add local annotation
scripts/tags.sh: use more portable -path instead of -wholename
scripts/tags.sh: Update comment (addition of gtags)
firmware: zynqmp: Convert to platform remove callback returning void
firmware: turris-mox-rwtm: Convert to platform remove callback returning void
firmware: stratix10-svc: Convert to platform remove callback returning void
firmware: stratix10-rsu: Convert to platform remove callback returning void
firmware: raspberrypi: Convert to platform remove callback returning void
firmware: qemu_fw_cfg: Convert to platform remove callback returning void
firmware: mtk-adsp-ipc: Convert to platform remove callback returning void
firmware: imx-dsp: Convert to platform remove callback returning void
firmware: coreboot_table: Convert to platform remove callback returning void
firmware: arm_scpi: Convert to platform remove callback returning void
firmware: arm_scmi: Convert to platform remove callback returning void
...
- Move the generic PM domain and its governor to the pmdomain subsystem
- Drop the unused pm_genpd_opp_to_performance_state()
Providers:
- Convert some providers to let the ->remove() callback return void
- amlogic: Add support for G12A ISP power domain
- arm: Move the SCPI power-domain driver to the pmdomain subsystem
- arm: Move Kconfig options to the pmdomain subsystem
- qcom: Update part number to X1E80100 for the rpmhpd
-----BEGIN PGP SIGNATURE-----
iQJLBAABCgA1FiEEugLDXPmKSktSkQsV/iaEJXNYjCkFAmWhIk8XHHVsZi5oYW5z
c29uQGxpbmFyby5vcmcACgkQ/iaEJXNYjCnvBBAAslgbFE31AthRFjRizsIhLD4+
WXYbuAEWUGOV0VKbcs6JLGqMmgqZ8caPieNWNDPz18M2BpJ3MguS7k5YW6G12QIb
7nmL/DCYrObO+Q8hMqPaHMRuV6+KjJ+y6UbZrKHKq+ROE+Pk5vfMk1x68nA+J5mO
rmsDv6eAsBggo4ubDcQ79bJf4t7RdWAcNz6IY8fwZ9HkNbbaC6db6BT0t9f1aTX7
yeZWxdy317y174xdwPTtQ5dnXQmC3FEBCuG4M0J4gb6nvLtbpoeYqlGrxkNGKxqv
1IfMl45uu7OuGSq1f3LSpuQluAQs99KG8Y9vTG6kXKC5Xu3sIijciaGTJsCao91e
af9pjLeX3DWl0RaLUtOB0h78meCHxf79kFUkGUv89FzIWh8iQMWcdwePeXXSNXag
AklV/gpodCj501Dk1wjs2/3eVI5YUsEcqhLvu9Q3gzDqXy4px8Keut8AollNsfg8
nZ9P3Kr0eHV2xqtTGYKheebLj5IDWGPC6XS+L60piij52gN6QWnywX/8Kjdms1l6
2CclTrJ1YZG+I6tLTnrsdy0m9U2w5V2DP/rf+m/lQTRG2d9ZWdKQ+qzakQ7va4Pz
hokLrm1cC0Wcx/ldwV1wC62WkTnRBmtA4ONMzibAFUCboay8xU7p0OaRmBJcOaPF
+Nw7Mt3tt4Qn7iE8Fd4=
=xSMR
-----END PGP SIGNATURE-----
Merge tag 'pmdomain-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm
Pull pmdomain updates from Ulf Hansson:
"Core:
- Move the generic PM domain and its governor to the pmdomain
subsystem
- Drop the unused pm_genpd_opp_to_performance_state()
Providers:
- Convert some providers to let the ->remove() callback return void
- amlogic: Add support for G12A ISP power domain
- arm: Move the SCPI power-domain driver to the pmdomain subsystem
- arm: Move Kconfig options to the pmdomain subsystem
- qcom: Update part number to X1E80100 for the rpmhpd"
* tag 'pmdomain-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/linux-pm:
PM: domains: Move genpd and its governor to the pmdomain subsystem
PM: domains: Drop redundant header for genpd
PM: domains: Drop the unused pm_genpd_opp_to_performance_state()
PM: domains: fix domain_governor kernel-doc warnings
pmdomain: xilinx/zynqmp: Convert to platform remove callback returning void
pmdomain: qcom-cpr: Convert to platform remove callback returning void
pmdomain: imx93-pd: Convert to platform remove callback returning void
pmdomain: imx93-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx8mp-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx8m-blk-ctrl: Convert to platform remove callback returning void
pmdomain: imx-gpcv2: Convert to platform remove callback returning void
pmdomain: imx-gpc: Convert to platform remove callback returning void
pmdomain: imx-pgc: Convert to platform remove callback returning void
pmdomain: amlogic: meson-ee-pwrc: add support for G12A ISP power domain
dt-bindings: power: meson-g12a-power: document ISP power domain
firmware: arm_scpi: Move power-domain driver to the pmdomain dir
pmdomain: arm_scmi: Move Kconfig options to the pmdomain subsystem
pmdomain: qcom: rpmhpd: Update part number to X1E80100
dt-bindings: power: rpmpd: Update part number to X1E80100
A new drivers/cache/ subsystem is added to contain drivers for abstracting
cache flush methods on riscv and potentially others, as this is needed for
handling non-coherent DMA but several SoCs require nonstandard hardware
methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and MT8195,
and driver support for MT8188 along with some code refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and hisilicon
-----BEGIN PGP SIGNATURE-----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=4bKY
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"A new drivers/cache/ subsystem is added to contain drivers for
abstracting cache flush methods on riscv and potentially others, as
this is needed for handling non-coherent DMA but several SoCs require
nonstandard hardware methods for it.
op-tee gains support for asynchronous notification with FF-A, as well
as support for a system thread for executing in secure world.
The tee, reset, bus, memory and scmi subsystems have a couple of minor
updates.
Platform specific soc driver changes include:
- Samsung Exynos gains driver support for Google GS101 (Tensor G1)
across multiple subsystems
- Qualcomm Snapdragon gains support for SM8650 and X1E along with
added features for some other SoCs
- Mediatek adds support for "Smart Voltage Scaling" on MT8186 and
MT8195, and driver support for MT8188 along with some code
refactoring.
- Microchip Polarfire FPGA support for "Auto Update" of the FPGA
bitstream
- Apple M1 mailbox driver is rewritten into a SoC driver
- minor updates on amlogic, mvebu, ti, zynq, imx, renesas and
hisilicon"
* tag 'soc-drivers-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (189 commits)
memory: ti-emif-pm: Convert to platform remove callback returning void
memory: ti-aemif: Convert to platform remove callback returning void
memory: tegra210-emc: Convert to platform remove callback returning void
memory: tegra186-emc: Convert to platform remove callback returning void
memory: stm32-fmc2-ebi: Convert to platform remove callback returning void
memory: exynos5422-dmc: Convert to platform remove callback returning void
memory: renesas-rpc-if: Convert to platform remove callback returning void
memory: omap-gpmc: Convert to platform remove callback returning void
memory: mtk-smi: Convert to platform remove callback returning void
memory: jz4780-nemc: Convert to platform remove callback returning void
memory: fsl_ifc: Convert to platform remove callback returning void
memory: fsl-corenet-cf: Convert to platform remove callback returning void
memory: emif: Convert to platform remove callback returning void
memory: brcmstb_memc: Convert to platform remove callback returning void
memory: brcmstb_dpfe: Convert to platform remove callback returning void
soc: qcom: llcc: Fix LLCC_TRP_ATTR2_CFGn offset
firmware: qcom: qseecom: fix memory leaks in error paths
dt-bindings: clock: google,gs101: rename CMU_TOP gate defines
soc: qcom: llcc: Fix typo in kernel-doc
dt-bindings: soc: qcom,aoss-qmp: document the X1E80100 Always-On Subsystem side channel
...
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/86165c8ccd0bb47000a29e711102795b36c8df41.1703693980.git.u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Few minor updates:
1. Addition of protocol versioning checks to warn if the firmware version
is newer or greater than the version supported by the kernel driver
2. Increment of the maximum OPP count in the perf protocol from 16 to 32
as needed by a few recent/future qualcomm platforms
3. Optimisation of set performance operations by returning error
immediately and avoiding to send the command to the platform(which
would return error eventually) if the domain doesn't support perf
operations. Similarly, the fastchannel handling is also optimised by
avoiding to initialise the corresponding set operations fastchannels.
4. Extension of extended names helper to accomodate recently added new
flags parameter to be able to properly configure the command used to
query the extended name of a resource.
-----BEGIN PGP SIGNATURE-----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=VpGl
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=h4CZ
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm SCMI updates for v6.8
Few minor updates:
1. Addition of protocol versioning checks to warn if the firmware version
is newer or greater than the version supported by the kernel driver
2. Increment of the maximum OPP count in the perf protocol from 16 to 32
as needed by a few recent/future qualcomm platforms
3. Optimisation of set performance operations by returning error
immediately and avoiding to send the command to the platform(which
would return error eventually) if the domain doesn't support perf
operations. Similarly, the fastchannel handling is also optimised by
avoiding to initialise the corresponding set operations fastchannels.
4. Extension of extended names helper to accomodate recently added new
flags parameter to be able to properly configure the command used to
query the extended name of a resource.
* tag 'scmi-updates-6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
firmware: arm_scmi: Add protocol versioning checks
firmware: arm_scmi: Increase the maximum opp count in the perf protocol
firmware: arm_scmi: Fix NULL pointer dereference during fastchannel init
firmware: arm_scmi: Add optional flags to extended names helper
firmware: arm_scmi: Populate fastchannel info only if set operations are allowed
firmware: arm_scmi: Check beforehand if the perf domain set operations are allowed
Link: https://lore.kernel.org/r/20231213115953.3578115-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The multiplier is already promoted to unsigned long, however the
frequency calculations done when using level indexing mode doesn't
use the multiplier computed. It instead hardcodes the multiplier
value of 1000 at all the usage sites.
Clean that up by assigning the multiplier value of 1000 when using
the perf level indexing mode and update the frequency calculations to
use the multiplier instead. It should fix the possible frequency
truncation for all the values greater than or equal to 4GHz on 64-bit
machines.
Fixes: 31c7c1397a ("firmware: arm_scmi: Add v3.2 perf level indexing mode support")
Reported-by: Sibi Sankar <quic_sibis@quicinc.com>
Closes: https://lore.kernel.org/all/20231129065748.19871-3-quic_sibis@quicinc.com/
Cc: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231130204343.503076-2-sudeep.holla@arm.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Fix the possible frequency truncation for all values equal to or greater
4GHz on 64bit machines by updating the multiplier 'mult_factor' to
'unsigned long' type. It is also possible that the multiplier itself can
be greater than or equal to 2^32. So we need to also fix the equation
computing the value of the multiplier.
Fixes: a9e3fbfaa0 ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Sibi Sankar <quic_sibis@quicinc.com>
Closes: https://lore.kernel.org/all/20231129065748.19871-3-quic_sibis@quicinc.com/
Cc: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231130204343.503076-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Platform and agent supported protocols versions do not necessarily match.
When talking to an older SCMI platform, supporting only older protocol
versions, the kernel SCMI agent will downgrade the version of the used
protocol to match the platform and avoid compatibility issues.
In the case where the kernel/OSPM agent happens to communicate with a
newer platform which can support newer protocol versions unknown to
the agent, and potentially backward incompatible, the agent currently
carries on, silently, in a best-effort approach.
Note that the SCMI specification doesn't provide means to explicitly
detect the protocol versions used by the agents, neither it is required
to support multiple, older, protocol versions.
Add an explicit protocol version check to let the agent detect when this
version mismatch happens and warn the user about this condition.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231201135858.2367651-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The number of opps on certain variants of the X1E80100 SoC are greater
than current maximum of 16, so increase the MAX_OPP count to 32 (next
power of 2) to accommodate that.
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20231129065748.19871-4-quic_sibis@quicinc.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The scmi_perf_domain_lookup requires the protocol handle to have the
private data set, which is yet to happen during the fastchannel init
scenario. This results in a NULL pointer dereference. Fix this by using
the pre-populated perf_dom_info to pass on the required information
instead.
| scmi_perf_protocol_init+0x434/0x678
| scmi_get_protocol_instance+0x168/0x29c
| scmi_devres_protocol_instance_get+0x50/0xa0
| scmi_devm_protocol_get+0x20/0x50
| scmi_cpufreq_probe+0x34/0xd4
| scmi_dev_probe+0x28/0x3c
| really_probe+0x148/0x2ac
| __driver_probe_device+0x78/0x12c
| driver_probe_device+0x40/0x160
| __device_attach_driver+0xb8/0x134
| bus_for_each_drv+0x80/0xdc
| __device_attach+0xa8/0x1b0
| device_initial_probe+0x14/0x20
| bus_probe_device+0xa8/0xac
| device_add+0x5cc/0x778
| device_register+0x20/0x30
| __scmi_device_create.part.0+0xec/0x1cc
| scmi_device_create+0x180/0x1c4
| scmi_create_protocol_devices+0x4c/0xb0
| scmi_probe+0x660/0x738
| platform_probe+0x68/0xdc
| really_probe+0x148/0x2ac
| __driver_probe_device+0x78/0x12c
| driver_probe_device+0x40/0x160
| __device_attach_driver+0xb8/0x134
| bus_for_each_drv+0x80/0xdc
| __device_attach+0xa8/0x1b0
| device_initial_probe+0x14/0x20
| bus_probe_device+0xa8/0xac
| deferred_probe_work_func+0x88/0xc0
| process_one_work+0x13c/0x264
| worker_thread+0x32c/0x438
| kthread+0x118/0x11c
| ret_from_fork+0x10/0x20
Fixes: 619bc6e034 ("firmware: arm_scmi: Populate fastchannel info only if set operations are allowed")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Link: https://lore.kernel.org/r/20231129065748.19871-2-quic_sibis@quicinc.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The Kconfig options belongs closer to the corresponding implementations,
hence let's move them from the firmware to the pmdomain subsystem.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20231123120847.2825444-1-sudeep.holla@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Changes SCMI optee transport to call tee_client_system_session()
to request optee driver to provision an entry context in OP-TEE
for processing OP-TEE messages. This prevents possible deadlock
in case OP-TEE threads are all consumed while these may be waiting
for a clock or regulator to be enable which SCMI OP-TEE service which
requires a free thread context to execute.
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Some recently added SCMI protocols needs an additional flags parameter to
be able to properly configure the command used to query the extended name
of a resource.
Modify extended_name_get helper accordingly.
Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231114145449.3136412-1-cristian.marussi@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Certain SCMI performance domains may have restrictions on the set level
and/or limits operation. If the SCMI domain supports fastchannel and the
set operations are not allowed, then any attempts to fetch the fastchannel
information for set level and/or limits operation will result in the
SCMI platform returning SCMI_ERR_SUPPORT. However, since this information
about the domain is already known to the agent(OSPM here) obtained via
PERF_DOMAIN_ATTRIBUTES, the agent(OSPM) can avoid calls to the firmware
trying to fetch the fastchannel information for the same.
Add those checks and skip querying the fastchannel information from the
firmware based on the information collected during the domain enumeration
stage.
Link: https://lore.kernel.org/r/20231113143252.37160-1-sudeep.holla@arm.com
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Certain SCMI performance domains may have restrictions on the set level
and/or limits operation. If the set level/limits are performed by an
agent who is not allowed to do so may get SCMI_ERR_SUPPORT. However,
since this information about the domain is already known to the
agent(OSPM here) obtained via PERF_DOMAIN_ATTRIBUTES, the agent(OSPM)
can avoid making PERF_LEVEL_SET and PERF_LIMITS_SET calls to the firmware.
Add those checks and return -ENOTSUPP to the caller without interacting
with the firmware based on the information collected during the domain
enumeration stage.
Signed-off-by: xinglong.yang <xinglong.yang@cixtech.com>
Link: https://lore.kernel.org/r/20231109082855.472681-1-xinglong.yang@cixtech.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Main additions this time include:
1. SCMI v3.2 clock configuration support:
This helps to retrieve the enabled state of a clock as well as allow
to set OEM specific clock configurations.
2. Support for generic performance scaling(DVFS):
The current SCMI DVFS support is limited to the CPUs in the kernel.
This extension enables it to used for all kind of devices and not
only for the CPUs. It updates the SCMI cpufreq to utilize the power
domain bindings. It also adds a more generic SCMI performance domain
based on the genpd framework that as be used for all the non-CPU
devices.
3. Extend the generic performance scaling(DVFS) support for firmware
driver OPPs:
Consumer drivers for devices that are attached to the SCMI performance
domain can't make use of the current OPP library to scale performance
as the OPPs are firmware driven and often obtained from the firmware
rather than the device tree. These changes extend the generic OPP
and genpd PM domain frameworks to identify and utilise these firmware
driven OPPs.
4. SCMI v3.2 clock parent support:
This enables the support for discovering and changing parent clocks
and extending the SCMI clk driver to use the same.
5. Qualcom SMC/HVC transport support:
The Qualcomm virtual platforms require capability id in the hypervisor
call to identify which doorbell to assert when supporting multiple
SMC/HVC based SCMI transport channels. Extra parameter is added to
support the same and the same is obtained at the fixed address in the
shared memory which is initialised by the firmware.
6. Move the existing SCMI power domain driver under drivers/pmdomain
Apart from the above main changes, it also include couple of minor fixes
and cosmetic reworks.
-----BEGIN PGP SIGNATURE-----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=IbXh
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=u9+1
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into soc/drivers
Arm SCMI updates for v6.7
Main additions this time include:
1. SCMI v3.2 clock configuration support:
This helps to retrieve the enabled state of a clock as well as allow
to set OEM specific clock configurations.
2. Support for generic performance scaling(DVFS):
The current SCMI DVFS support is limited to the CPUs in the kernel.
This extension enables it to used for all kind of devices and not
only for the CPUs. It updates the SCMI cpufreq to utilize the power
domain bindings. It also adds a more generic SCMI performance domain
based on the genpd framework that as be used for all the non-CPU
devices.
3. Extend the generic performance scaling(DVFS) support for firmware
driver OPPs:
Consumer drivers for devices that are attached to the SCMI performance
domain can't make use of the current OPP library to scale performance
as the OPPs are firmware driven and often obtained from the firmware
rather than the device tree. These changes extend the generic OPP
and genpd PM domain frameworks to identify and utilise these firmware
driven OPPs.
4. SCMI v3.2 clock parent support:
This enables the support for discovering and changing parent clocks
and extending the SCMI clk driver to use the same.
5. Qualcom SMC/HVC transport support:
The Qualcomm virtual platforms require capability id in the hypervisor
call to identify which doorbell to assert when supporting multiple
SMC/HVC based SCMI transport channels. Extra parameter is added to
support the same and the same is obtained at the fixed address in the
shared memory which is initialised by the firmware.
6. Move the existing SCMI power domain driver under drivers/pmdomain
Apart from the above main changes, it also include couple of minor fixes
and cosmetic reworks.
* tag 'scmi-updates-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: (37 commits)
firmware: arm_scmi: Add qcom smc/hvc transport support
dt-bindings: arm: Add new compatible for smc/hvc transport for SCMI
firmware: arm_scmi: Convert u32 to unsigned long to align with arm_smccc_1_1_invoke()
clk: scmi: Add support for clock {set,get}_parent
firmware: arm_scmi: Add support for clock parents
clk: scmi: Free scmi_clk allocated when the clocks with invalid info are skipped
firmware: arm_scpi: Use device_get_match_data()
firmware: arm_scmi: Add generic OPP support to the SCMI performance domain
firmware: arm_scmi: Specify the performance level when adding an OPP
firmware: arm_scmi: Simplify error path in scmi_dvfs_device_opps_add()
OPP: Extend support for the opp-level beyond required-opps
OPP: Switch to use dev_pm_domain_set_performance_state()
OPP: Extend dev_pm_opp_data with a level
OPP: Add dev_pm_opp_add_dynamic() to allow more flexibility
PM: domains: Implement the ->set_performance_state() callback for genpd
PM: domains: Introduce dev_pm_domain_set_performance_state()
firmware: arm_scmi: Rename scmi_{msg_,}clock_config_{get,set}_{2,21}
firmware: arm_scmi: Do not use !! on boolean when setting msg->flags
firmware: arm_scmi: Move power-domain driver to the pmdomain dir
pmdomain: arm: Add the SCMI performance domain
...
Link: https://lore.kernel.org/r/20231010124347.1620040-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This change adds the support for SCMI message exchange on Qualcomm
virtual platforms.
The hypervisor associates an object-id also known as capability-id
with each smc/hvc doorbell object. The capability-id is used to
identify the doorbell from the VM's capability namespace, similar
to a file-descriptor.
The hypervisor, in addition to the function-id, expects the capability-id
to be passed in x1 register when SMC/HVC call is invoked.
The capability-id is allocated by the hypervisor on bootup and is stored in
the shmem region by the firmware before starting Linux.
Signed-off-by: Nikunj Kela <quic_nkela@quicinc.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Link: https://lore.kernel.org/r/20231009191437.27926-3-quic_nkela@quicinc.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
All the parameters to arm_smccc_1_1_invoke() are unsigned long which
aligns well on both 32-bit and 64-bit Arm based platforms. Let us store
all the members in the structure scmi_smc used as the parameters to the
arm_smccc_1_1_invoke() call as unsigned long.
Cc: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20231009152049.1428872-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
SCMI v3.2 spec introduces CLOCK_POSSIBLE_PARENTS_GET, CLOCK_PARENT_SET
and CLOCK_PARENT_GET. Add support for these to enable clock parents
and use them in the clock driver.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20231004-scmi-clock-v3-v5-1-1b8a1435673e@nxp.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
To enable the performance level to be used for OPPs, let's convert into
using the dev_pm_opp_add_dynamic() API when creating them. This will be
particularly useful for the SCMI performance domain, as shown through
subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230925131715.138411-9-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Let's simplify the code in scmi_dvfs_device_opps_add() by using
dev_pm_opp_remove_all_dynamic() in the error path.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230925131715.138411-8-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
It is very confusing to use *_v2 for everything applicable until SCMI
clock protocol version v2.0 including v1.0 for example. So let us rename
such that *_v2 is used only for SCMI clock protocol v2.1 onwards. Also
add comment to indicate the same explicitly.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230925101557.3839860-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Both pc->async_powercap_cap_set and ignore_dresp are already boolean.
Use of !! on them is obviously dubious.
Sparse reports:
drivers/firmware/arm_scmi/powercap.c:363:17: warning: dubious: x & !y
drivers/firmware/arm_scmi/powercap.c:363:17: warning: dubious: x & !y
Remove the unnecessary !! and get rid of the warning.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230921085257.3125744-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
To simplify with maintenance let's move the Arm SCMI power-domain driver
to the new pmdomain directory.
Link: https://lore.kernel.org/all/20230921113328.3208651-1-sudeep.holla@arm.com
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
To enable support for performance scaling (DVFS) for generic devices with
the SCMI performance protocol, let's add an SCMI performance domain. This
is being modelled as a genpd provider, with support for performance scaling
through genpd's ->set_performance_state() callback.
Note that, this adds the initial support that allows consumer drivers for
attached devices, to vote for a new performance state via calling the
dev_pm_genpd_set_performance_state(). However, this should be avoided as
it's in most cases preferred to use the OPP library to vote for a new OPP
instead. The support using the OPP library isn't part of this change, but
needs to be implemented from subsequent changes.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Link: https://lore.kernel.org/r/20230919121605.7304-1-ulf.hansson@linaro.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
