This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port. Firmware
will send notification to the driver for the disabled port when this
happens. Define a new field in the link_info structure to keep track
of this state. The new phy_state field replaces the unused loop_back
field.
Log a message when the phy_state changes state. In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool PAM4 link modes for:
50000baseCR_Full
100000baseCR2_Full
200000baseCR4_Full
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware interface has added support for new link speeds using
PAM4 modulation. Expand the bnxt_link_info structure to closely
mirror the new firmware structures. Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.
Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the comment typo: "compliment" -> "complement".
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong flag value caused the firmware call to return actual port
counters instead of the counter masks. This messed up the counter
overflow logic and caused erratic extended port counters to be
displayed under ethtool -S.
Fixes: 531d1d269c ("bnxt_en: Retrieve hardware masks for port counters.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix it to set the required fid input parameter. The firmware call
fails without this patch.
Fixes: d752d0536c ("bnxt_en: Retrieve hardware counter masks from firmware if available.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Debug firmware commands are not supported on VFs to read registers.
This patch avoids logging unnecessary access_denied error on VFs
when user calls ETHTOOL_GREGS.
By returning error in get_regs_len() method on the VF, the get_regs()
method will not be called.
Fixes: b5d600b027 ("bnxt_en: Add support for 'ethtool -d'")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All changes related to bp->link_info require the protection of the
link_lock mutex. It's not sufficient to rely just on RTNL.
Fixes: 163e9ef636 ("bnxt_en: Fix race when modifying pause settings.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning "unknown" as a temperature value violates the hwmon interface
rules. Appropriate error codes should be returned via device_attribute
show instead. These will ultimately be propagated to the user via the
file system interface.
In addition to the corrected error handling, it is an even better idea to
not present the sensor in sysfs at all if it is known that the read will
definitely fail. Given that temp1_input is currently the only sensor
reported, ensure no hwmon registration if TEMP_MONITOR_QUERY is not
supported or if it will fail due to access permissions. Something smarter
may be needed if and when other sensors are added.
Fixes: 12cce90b93 ("bnxt_en: fix HWRM error when querying VF temperature")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using strlcpy() to copy from VPD is not correct because VPD strings
are not necessarily NULL terminated. Use memcpy() to copy the VPD
length up to the destination buffer size - 1. The destination is
zeroed memory so it will always be NULL terminated.
Fixes: a0d0fd70fe ("bnxt_en: Read partno and serialno of the board from VPD")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses the following coccinelle warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15415:1-26: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:12393:2-17: WARNING:
Assignment of 0/1 to bool variable
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:15497:2-27: WARNING:
Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses the following coccinelle warning:
drivers/net/ethernet/broadcom/b44.c:2213:6-20: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2218:2-16: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2226:3-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/broadcom/b44.c:2230:3-17: WARNING: Assignment of
0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These stats are already reported in ethtool -S.
Michael confirms they are equivalent to standard stats.
v2: - fix sparse warning about endian by using the macro
- use u64 for pointer type
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow drivers to call napi_hash_del() before calling
netif_napi_del() to batch RCU grace periods. This makes
the API asymmetric and leaks internal implementation details.
Soon we will want the grace period to protect more than just
the NAPI hash table.
Restructure the API and have drivers call a new function -
__netif_napi_del() if they want to take care of RCU waits.
Note that only core was checking the return status from
napi_hash_del() so the new helper does not report if the
NAPI was actually deleted.
Some notes on driver oddness:
- veth observed the grace period before calling netif_napi_del()
but that should not matter
- myri10ge observed normal RCU flavor
- bnx2x and enic did not actually observe the grace period
(unless they did so implicitly)
- virtio_net and enic only unhashed Rx NAPIs
The last two points seem to indicate that the calls to
napi_hash_del() were a left over rather than an optimization.
Regardless, it's easy enough to correct them.
This patch may introduce extra synchronize_net() calls for
interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on
free_netdev() to call netif_napi_del(). This seems inevitable
since we want to use RCU for netpoll dev->napi_list traversal,
and almost no drivers set IFF_DISABLE_NETPOLL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:4238: warning: Excess function parameter 'netdev' description in 'bnx2x_setup_tc'
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c:4238: warning: Excess function parameter 'tc' description in 'bnx2x_setup_tc'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() which runs from a workqueue can race with
bnxt_remove_one(). For example, if firmware reset and VF FLR are
happening at about the same time.
bnxt_remove_one() already cancels the workqueue and waits for it
to finish, but we need to do this earlier before the devlink
reporters are destroyed. This will guarantee that
the devlink reporters will always be valid when bnxt_fw_reset_task()
is still running.
Fixes: b148bb238c ("bnxt_en: Fix possible crash in bnxt_fw_reset_task().")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the driver goes through PCIe AER reset in error state, all
firmware messages will timeout because the PCIe bus is no longer
accessible. This can lead to AER reset taking many minutes to
complete as each firmware command takes time to timeout.
Define a new macro BNXT_NO_FW_ACCESS() to skip these firmware messages
when either firmware is in fatal error state or when
pci_channel_offline() is true. It now takes a more reasonable 20 to
30 seconds to complete AER recovery.
Fixes: b4fff2079d ("bnxt_en: Do not send firmware messages if firmware is in error state.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
It is necessary to manage the Wake-on-LAN clock to turn on the
appropriate blocks for MPD or CFP-based packet matching to work
otherwise we will not be able to reliably match packets during suspend.
Reported-by: Blair Prescott <blair.prescott@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We disable clocks shortly after probing the device to save as much power as
possible in case the interface is never used. When bcm_sysport_open() is
invoked, clocks are enabled, and disabled in bcm_sysport_stop().
A similar scheme is applied to the suspend/resume functions.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db21997379 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VALIDATE_MASK(eth_mask->h_source) is checked twice in a row in
bcmgenet_validate_flow(). Add VALIDATE_MASK(eth_mask->h_dest)
instead.
Fixes: 3e37095228 ("net: bcmgenet: add support for ethtool rxnfc flows")
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent changes to support user-defined RSS map assume that RX
rings are always reserved and the default RSS map is set after the
RX rings are successfully reserved. If the firmware spec is older
than 1.6.1, no ring reservations are required and the default RSS
map is not setup at all. In another scenario where the fw Resource
Manager is older, RX rings are not reserved and we also end up with
no valid RSS map.
Fix both issues in bnxt_need_reserve_rings(). In both scenarios
described above, we don't need to reserve RX rings so we need to
call this new function bnxt_check_rss_map_no_rmgr() to setup the
default RSS map when needed.
Without valid RSS map, the NIC won't receive packets properly.
Fixes: 1667cbf6a4 ("bnxt_en: Add logical RSS indirection table structure.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no VF rings available during probe when the device is configured
using the Minimal-Static reservation strategy. In this case, the RSS
indirection table can only be initialized later, during bnxt_open_nic().
However, this was not happening because the rings will already have been
reserved via bnxt_init_dflt_ring_mode(), causing bnxt_need_reserve_rings()
to return false in bnxt_reserve_rings() and bypass the RSS table init.
Solve this by pushing the call to bnxt_set_dflt_rss_indir_tbl() into
__bnxt_reserve_rings(), which is common to both paths and is called
whenever ring configuration is changed. After doing this, the RSS table
init that must be called from bnxt_init_one() happens implicitly via
bnxt_set_default_rings(), necessitating doing the allocation earlier in
order to avoid a null pointer dereference.
Fixes: bd3191b5d8 ("bnxt_en: Implement ethtool -X to set indirection table.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware returns RESOURCE_ACCESS_DENIED for HWRM_TEMP_MONITORY_QUERY for
VFs. This produces unpleasing error messages in the log when temp1_input
is queried via the hwmon sysfs interface from a VF.
The error is harmless and expected, so silence it and return unknown as
the value. Since the device temperature is not particularly sensitive
information, provide flexibility to change this policy in future by
silencing the error rather than avoiding the HWRM call entirely for VFs.
Fixes: cde49a42a9 ("bnxt_en: Add hwmon sysfs support to read temperature")
Cc: Marc Smith <msmith626@gmail.com>
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnxt_fw_reset_task() is run from a delayed workqueue. The current
code is not cancelling the workqueue in the driver's .remove()
method and it can potentially crash if the device is removed with
the workqueue still pending.
The fix is to clear the BNXT_STATE_IN_FW_RESET flag and then cancel
the delayed workqueue in bnxt_remove_one(). bnxt_queue_fw_reset_work()
also needs to check that this flag is set before scheduling. This
will guarantee that no rescheduling will be done after it is cancelled.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, save
the PCI state after initialization and restore it after the slot
reset.
Fixes: 6316ea6db9 ("bnxt_en: Enable AER support.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are returning the wrong count for ETH_SS_STATS in get_sset_count()
when XDP or TCs are enabled. In a recent commit, we got rid of
irrelevant counters when the ring is RX only or TX only, but we
did not make the proper adjustments for the count. As a result,
when we have XDP or TCs enabled, we are returning an excess count
because some of the rings are TX only. This causes ethtool -S to
display extra counters with no counter names.
Fix bnxt_get_num_ring_stats() by not assuming that all rings will
always have RX and TX counters in combined mode.
Fixes: 125592fbf4 ("bnxt_en: show only relevant ethtool stats for a TX or RX ring")
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If firmware goes into unstable state, HWRM_NVM_GET_DIR_INFO firmware
command may return zero dir entries. Return error in such case to
avoid zero length dma buffer request.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare conditions like two stage OS installation, the
ethtool's get_channels function may be called when the
device is in D3 state, leading to uncorrectable PCI error.
Check netif_running() first before making any query to FW
which involves writing to BAR.
Fixes: db4723b3cd ("bnxt_en: Check max_tx_scheduler_inputs value from firmware.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When devm_kcalloc() fails, dev should be freed just
like what we've done in the subsequent error paths.
Fixes: 7b78be48a8 ("net: systemport: Dynamically allocate number of TX rings")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
./drivers/net/ethernet/broadcom/bnxt/bnxt.c:3730:19-37: WARNING:
dma_alloc_coherent use in stats -> hw_stats already zeroes out
memory, so memset is not needed
dma_alloc_coherent use in status already zeroes out memory,
so memset is not needed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
