if mtk_jpeg_clk_init() succeed, mtk_jpeg_probe() and mtk_jpeg_remove()
doesn't have a corresponding put_device(). Thus add a new helper
mtk_jpeg_clk_release() to fix it.
Fixes: b2f0d2724b ("[media] vcodec: mediatek: Add Mediatek JPEG Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To avoid potentially overflowing the kernel logs in the case
of corrupted streams, this commit replaces an error message with
a per-stream counter to be read through a driver-specific
control.
Applications can read the per-stream accumulated
error macroblocks count.
The old error message is replaced by a rate-limited debug message.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's possible that the VPU was initialized using just one buffer,
containing only codec headers.
In this case, right after the initialization and after updating
the FIFO read pointer, we need to iterate through all the coda_buffer_meta
and release any metas that have been already used by the VPU.
This issue is affecting indirectly the bitstream buffer fill
threshold, which depends on the meta end position of the first
queued meta, which is passed to coda_bitstream_can_fetch_past().
Without this fix, it's possible that for certain videos, the
bitstream buffer level is not filled properly, resulting in a PIC_RUN
timeout.
Reported-by: Benjamin Bara <benjamin.bara@skidata.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit 9495b7e92f ("driver core: platform: Initialize dma_parms for
platform devices") included dma_parms in platform_device. There's no need
to allocate again.
Fixes: 13483fc2f2 ("media: mtk-vcodec: set dma max segment size")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
isif_probe() invokes iounmap() on error handling paths, but it does not
reset the global state. So, later it can invoke iounmap() even when
ioremap() fails. This is the case also for isif_remove(). The patch
resets the global state after invoking iounmap() to avoid this.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace dmaengine_terminate_all() by dmaengine_terminate_sync()
to ensure that all pending dma operations are really finished.
This is not ensured by dmaengine_terminate_all() and this API
is deprecated, so better to use the _sync() variant.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Philippe CORNU <philippe.cornu@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The only supported bus for the R-Car CSI-2 driver is CSI-2 DPHY, specify
this before parsing the fwnode.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the fwnode_graph_get_endpoint_by_id() interface instead of
of_graph_get_endpoint_by_regs() to fetch the fwnode. This saves
translating between a device_node and fwnode_handle.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support for suspend and resume by stopping and starting the video
pipeline while still retaining all buffers given to the driver by
user-space and internally allocated ones, this gives the application a
seamless experience.
Buffers are never returned to user-space unprocessed so user-space don't
notice when suspending. When resuming the driver restarts the capture
session using the internal scratch buffer, this happens before
user-space is unfrozen, this leads to speedy response times once the
application resumes its execution.
As the entire pipeline is stopped on suspend all subdevices in use are
also stopped, and if they enter a shutdown state when not streaming
(such as the R-Car CSI-2 driver) they too will be suspended and resumed
in sync with the VIN driver.
To be able to do keep track of which VINs should be resumed a new
internal state SUSPENDED is added to recode this.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To support suspend and resume the ability to start and stop the hardware
needs to be available internally in the driver. Currently this code is
in the start and stop callbacks of the vb2_ops struct. In these
callbacks the code is intertwined with buffer allocation and freeing.
Prepare for suspend and resume support by breaking out the hardware
start/stop code into new methods.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation of suspend/resume support cache the chsel value when
written to the register so it can be restored on resume if needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When returning buffers to user-space it's no longer needed to examine
the buffers given to hardware as recent changes guarantees the only
buffer present in the hardware registers when the driver is not in the
running state is the scratch buffer.
Remove the special case and rename the function to better describe it
now only deals with buffers queued to the driver but not yet recorded in
the hardware registers.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In its early stages the VIN driver did not use an internal scratch
buffer. This leads to a unnecessary complex start and stop behavior,
specially for TB/BT. The driver now always allocates a scratch buffer to
deal with buffer under-runs, use the scratch buffer to also simplify
starting and stopping.
When capture is starting use the scratch buffer instead of a user-space
buffers while syncing the driver with the hardware state. This allows
the driver to know that no user-space buffer is given to the hardware
before the running state is reached.
When capture is stopping use the scratch buffer instead of leaving the
user-space buffers in place and add a check that all user-space buffers
are processed by the hardware before transitioning from the stopping to
stopped state. This allows the driver to know all user-space buffers
given to the hardware are fully processed.
This change in itself does not improve the driver much but it paves the
way for future simplifications and enhancements. One direct improvement
of this change is that TB/BT buffers returned to user-space while stopping
will always contain both fields, that was not guaranteed before.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
None of these BUG_ON()'s is justified. BUG_ON() should only be used when
there is really no way to survive.
If at all these could be replaced by lockdep_assert_preemption_enabled() to
cover all invalid caller context and not just those covered by
in_interrupt().
But all functions which are invoked from those places contain already debug
mechanisms to catch wrong context, so having these extra checks is not
having any advantage.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_vcodec_release_enc_pm() will be called in two places:
a. mtk_vcodec_init_enc_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_enc_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_enc_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_enc_pm()
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeed, mtk_vcodec_init_enc_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 4e855a6efa ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk_vcodec_release_dec_pm() will be called in two places:
a. mtk_vcodec_init_dec_pm() succeed while mtk_vcodec_probe() return error.
b. mtk_vcodec_dec_remove().
In both cases put_device() call is needed, since of_find_device_by_node()
was called in mtk_vcodec_init_dec_pm() previously.
Thus add put_devices() call in mtk_vcodec_release_dec_pm()
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeed, mtk_vcodec_init_dec_pm() doesn't have
a corresponding put_device(). Thus add jump target to fix the exception
handling for this function implementation.
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
if of_find_device_by_node() succeeds, mtk_jpeg_clk_init() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: 648372a87c ("media: platform: Change the call functions of getting/enable/disable the jpeg's clock")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Make interrupt naming more consistent by using a common
pattern for video and jpeg interrupts.
With this commit, interrupts are shown as:
29: 0 0 GPC 12 Level coda-video
30: 0 0 GPC 3 Level coda-jpeg
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of printing just the device type, let's use
the device name, which makes the message more useful.
With this commit, the messages shown when the driver
is registered are:
coda 2040000.vpu: Firmware code revision: 570363
coda 2040000.vpu: Initialized CODA960.
coda 2040000.vpu: Firmware version: 3.1.1
coda 2040000.vpu: coda-jpeg-encoder registered as video0
coda 2040000.vpu: coda-jpeg-decoder registered as video1
coda 2040000.vpu: coda-video-encoder registered as video2
coda 2040000.vpu: coda-video-decoder registered as video3
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The H.264 small buffer padding is done under
the (ctx->qsequence == 0 && payload < 512) condition.
Given this is the exact same condition immediately
above, we can move it right there, making the code
slightly clearer.
This change shouldn't affect functionality as it's just
cosmetics.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The ctx->initialized flag is set in __coda_decoder_seq_init,
so it's redundant to set it in coda_dec_seq_init_work.
Remove the redundant set, which allows to simplify the
implementation quite a bit.
This change shouldn't affect functionality as it's just
cosmetics.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mandatory compatible value 'renesas,rcar-gen2-vin' was added to all
Gen2 DTS files in 2017, remove the redundant device specific values from
the driver.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If CONFIG_PM is n, gcc warns:
drivers/media/platform/marvell-ccic/mmp-driver.c:324:12: warning: ‘mmpcam_runtime_suspend’ defined but not used [-Wunused-function]
static int mmpcam_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/marvell-ccic/mmp-driver.c:310:12: warning: ‘mmpcam_runtime_resume’ defined but not used [-Wunused-function]
static int mmpcam_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~~~
Mark them as __maybe_unused to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace commas with semicolons. Commas introduce unnecessary
variability in the code structure and are hard to see. What is done
is essentially described by the following Coccinelle semantic patch
(http://coccinelle.lip6.fr/):
// <smpl>
@@ expression e1,e2; @@
e1
-,
+;
e2
... when any
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix build warnings when CONFIG_PM is not set/enabled:
../drivers/media/platform/marvell-ccic/mmp-driver.c:324:12: warning: 'mmpcam_runtime_suspend' defined but not used [-Wunused-function]
324 | static int mmpcam_runtime_suspend(struct device *dev)
../drivers/media/platform/marvell-ccic/mmp-driver.c:310:12: warning: 'mmpcam_runtime_resume' defined but not used [-Wunused-function]
310 | static int mmpcam_runtime_resume(struct device *dev)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The addition of MT8183 support added a dependency on the SCP remoteproc
module. However the initial patch used the "select" Kconfig directive,
which may result in the SCP module to not be compiled if remoteproc was
disabled. In such a case, mtk-vcodec would try to link against
non-existent SCP symbols. "select" was clearly misused here as explained
in kconfig-language.txt.
Replace this by a "depends" directive on at least one of the VPU and
SCP modules, to allow the driver to be compiled as long as one of these
is enabled, and adapt the code to support this new scenario.
Also adapt the Kconfig text to explain the extra requirements for MT8173
and MT8183.
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
mtk-vcodec supports two kinds of firmware, VPU and SCP. Both were
supported from the same source files, but this is clearly unclean and
makes it more difficult to disable support for one or the other.
Move these implementations into their own file, after adding the
necessary private interfaces.
[hverkuil: smatch fix: mtk_vcodec_fw_vpu_init() error: uninitialized symbol 'rst_id'.]
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: bf1d556ad4 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common
code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
-----BEGIN PGP SIGNATURE-----
iQI/BAABCgApFiEEgdbnc3r/njty3Iq9D55TZVIEUYMFAl+IiPwLHGhjaEBsc3Qu
ZGUACgkQD55TZVIEUYPKEQ//TM8vxjucnRl/pklpMin49dJorwiVvROLhQqLmdxw
286ZKpVzYYAPc7LnNqwIBugnFZiXuHu8xPKQkIiOa2OtNDTwhKNoBxOAmOJaV6DD
8JfEtZYeX5mKJ/Nqd2iSkIqOvCwZ9Wzii+aytJ2U88wezQr1fnyF4X49MegETEey
FHWreSaRWZKa0MMRu9AQ0QxmoNTHAQUNaPc0PeqEtPULybfkGOGw4/ghSB7WcKrA
gtKTuooNOSpVEHkTas2TMpcBp6lxtOjFqKzVN0ml+/nqq5NeTSDx91VOCX/6Cj76
mXIg+s7fbACTk/BmkkwAkd0QEw4fo4tyD6Bep/5QNhvEoAriTuSRbhvLdOwFz0EF
vhkF0Rer6umdhSK7nPd7SBqn8kAnP4vBbdmB68+nc3lmkqysLyE4VkgkdH/IYYQI
6TJ0oilXWFmU6DT5Rm4FBqCvfcEfU2dUIHJr5wZHqrF2kLzoZ+mpg42fADoG4GuI
D/oOsz7soeaRe3eYfWybC0omGR6YYPozZJ9lsfftcElmwSsFrmPsbO1DM5IBkj1B
gItmEbOB9ZK3RhIK55T/3u1UWY3Uc/RVr+kchWvADGrWnRQnW0kxYIqDgiOytLFi
JZNH8uHpJIwzoJAv6XXSPyEUBwXTG+zK37Ce769HGbUEaUrE71MxBbQAQsK8mDpg
7fM=
=Bkf/
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping updates from Christoph Hellwig:
- rework the non-coherent DMA allocator
- move private definitions out of <linux/dma-mapping.h>
- lower CMA_ALIGNMENT (Paul Cercueil)
- remove the omap1 dma address translation in favor of the common code
- make dma-direct aware of multiple dma offset ranges (Jim Quinlan)
- support per-node DMA CMA areas (Barry Song)
- increase the default seg boundary limit (Nicolin Chen)
- misc fixes (Robin Murphy, Thomas Tai, Xu Wang)
- various cleanups
* tag 'dma-mapping-5.10' of git://git.infradead.org/users/hch/dma-mapping: (63 commits)
ARM/ixp4xx: add a missing include of dma-map-ops.h
dma-direct: simplify the DMA_ATTR_NO_KERNEL_MAPPING handling
dma-direct: factor out a dma_direct_alloc_from_pool helper
dma-direct check for highmem pages in dma_direct_alloc_pages
dma-mapping: merge <linux/dma-noncoherent.h> into <linux/dma-map-ops.h>
dma-mapping: move large parts of <linux/dma-direct.h> to kernel/dma
dma-mapping: move dma-debug.h to kernel/dma/
dma-mapping: remove <asm/dma-contiguous.h>
dma-mapping: merge <linux/dma-contiguous.h> into <linux/dma-map-ops.h>
dma-contiguous: remove dma_contiguous_set_default
dma-contiguous: remove dev_set_cma_area
dma-contiguous: remove dma_declare_contiguous
dma-mapping: split <linux/dma-mapping.h>
cma: decrease CMA_ALIGNMENT lower limit to 2
firewire-ohci: use dma_alloc_pages
dma-iommu: implement ->alloc_noncoherent
dma-mapping: add new {alloc,free}_noncoherent dma_map_ops methods
dma-mapping: add a new dma_alloc_pages API
dma-mapping: remove dma_cache_sync
53c700: convert to dma_alloc_noncoherent
...
New driver:
Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config
-----BEGIN PGP SIGNATURE-----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=4H8J
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
pixelformat in vin priv structure holds V4L2_PIX_FMT_* and not
MEDIA_BUS_FMT_* so make sure we check against V4L2_PIX_FMT_* formats
while setting the VNIS_REG.
Fixes: 8c3e0f67df ("media: rcar-vin: Extend RAW8 support to all RGB layouts")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Merge dma-contiguous.h into dma-map-ops.h, after removing the comment
describing the contiguous allocator into kernel/dma/contigous.c.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add proper control type to the recently introduced
V4L2_CID_MPEG_VIDEO_FRAME_SKIP_MODE control. This will forward it to
v4l2_ctrl_new_std_menu() not v4l2_ctrl_new_std(), what causes the
failure. This fixes the following warning during driver initialization:
s5p_mfc_enc_ctrls_setup:2671: Adding control (18) failed
s5p_mfc_open:811: Failed to setup mfc controls
Fixes: ef56b3ee4f ("media: s5p-mfc: Use standard frame skip mode control")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the list of supported formats to include all RGB layouts of RAW8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Extend the list of supported formats to include all RGB layouts of RAW8.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
delta_run_work() calls delta_get_sync() that increments
the reference counter. In case of failure, decrement the reference
count by calling delta_put_autosuspend().
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On calling pm_runtime_get_sync() the reference count of the device
is incremented. In case of failure, decrement the
reference count before returning the error.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
And also, when the call of function vpe_runtime_get() failed,
we won't call vpe_runtime_put().
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails
inside vpe_runtime_get().
Fixes: 4571912743 ("[media] v4l: ti-vpe: Add VPE mem to mem driver")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not
called in error handling paths. Thus replace the jump target
"err_release_buffers" by "err_pm_putw".
Fixes: 152e0bf602 ("media: stm32-dcmi: add power saving support")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, causing incorrect ref count if
pm_runtime_put_noidle() is not called in error handling paths.
Thus call pm_runtime_put_noidle() if pm_runtime_get_sync() fails.
Fixes: c5086f130a ("[media] s5p-mfc: Use clock gating only on MFC v5 hardware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
