The firmware will be able to only save and restore the context related to
library management.
This means that even without a full context save, the libraries do not
need to be re-loaded to the firmware after second or consecutive boots.
This is reported via the FW_READY notification, where BIT(15) indicates:
0 - the library restore is not done
1 - library restore is done
This bit is only valid if full context save is not enabled, full context
save is by definition saves and restores the library related book-keeping
as well.
Add a new flag to tell the platform code if the libraries have been
restored, no need to reload them after boot.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250619105623.4546-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ACE3 (Panther Lake) introduced support for microphone privacy feature which
can - in hardware - mute incoming audio data based on a state of a physical
switch.
The change in the privacy state is delivered through interface IP blocks
and can only be handled by the link owner.
In Intel platforms Soundwire is for example host owned, so the interrupt
can only be handled by the host.
Since the input stream is going to be muted by hardware, the host needs to
send a message to firmware about the change in privacy so it can execute a
fade out/in to enhance user experience.
The support for microphone privacy can be queried from the HW_CONFIG data
under the INTEL_MIC_PRIVACY_CAP tuple. This is Intel specific data, the
core will pass it to platform code if the intel_configure_mic_privacy()
callback is provided.
Platform code can call sof_ipc4_mic_privacy_state_change() to send the IPC
message to the firmware on state change.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://patch.msgid.link/20250307112816.1495-6-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason a number of files included the "All rights reserved"
statement. Good old copy-paste made sure this mistake proliferated.
Remove the "All rights reserved" in all Intel-copyright to align with
internal guidance.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20240503140359.259762-10-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the module notification message the information about the notification
is provided via the mailbox with the sof_ipc4_notify_module_data struct.
It contains the module and instance id of the sender of the notification,
the event_id and optionally additional data which is module and event
specific.
At the same time add definitions to identify ALSA kcontrol change
notification.
These notifications use standardized event_id, modules must follow this if
they support such notifications:
upper 16 bit: 0xA15A as a magic identification value
lower 16 bit: param_id of the changed control
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231124150853.18648-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro definitions of debug slot can be used by gdb, telemetry
and mtrace log, so move these definitions to header.h from mtrace.
Then these macro definitions can be shared
Signed-off-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230919092416.4137-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On Intel platforms there is a strict order requirement for the DMA
programming:
DSP side configures the buffer and sets the GEN bit
Host side sets the RUN bit.
In order to follow this flow, a new global message type has been added to
prepare the DSP side of the DMA:
host sends LOAD_LIBRARY_PREPARE with the dma_id
DSP side sets its buffer and sets the GEN bit
Host sets the RUN bit
Host sends LOAD_LIBRARY with dma_id and lib_id
DSP receives the library data.
It is up to the platform code to use the new prepare stage message and how
to handle the reply to it from the firmware, which can indicate that the
message type is not supported/handled.
In this case the kernel should proceed to the LOAD_LIBRARY stage assuming
a single stage library loading:
host sends LOAD_LIBRARY_PREPARE with the dma_id
DSP replies that the message type is not supported/handled
Host acknowledges the return code and sets the RUN bit
Host sends LOAD_LIBRARY with dma_id and lib_id
DSP receives the library data.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Link: https://lore.kernel.org/r/20230915114018.1701-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In the chained DMA mode, the firmware allocates buffers for the host
and link DMA, and takes care of copying data between host- and
link-DMA buffers in a low-latency thread. This is different to a
regular pipeline, no processing is allowed, and the connection between
host- and link DMA is handled with a dedicated IPC.
This patch exposes the macros needed to create the required IPC messages.
Signed-off-by: Jyri Sarha <jyri.sarha@intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230321092654.7292-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The create pipeline message can carry the target code_id which is set to
0 at the moment.
Add macros to set the core_id in the message extension.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20230307123556.31328-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the list of pipelines in the PCM stream's pipeline info to trigger
the pipelines in the right order. Add a helper for triggering pipelines
in batch mode that will be used to trigger multiple pipelines at the
same time.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230127120031.10709-12-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On Intel HDA platforms the library loading is done via DMA and an IPC
message is also need to be sent to initiate the downloading of the new
library.
Co-developed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20221020121238.18339-16-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The LOG_BUFFER_STATUS message includes the ID of the core which updated
its log buffer.
With IPC4 each core logs to a different slot in the debug window.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220909114332.31393-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
IPC4 uses the SET_DX message to enable/disable cores managed by the DSP.
The dx_state.core_mask indicates which core is going to change state,
the dx_state.dx_mask is to power on (1) or off (0) the core.
In the dx_mask only those bits (cores) checked which bit is set in the
core_mask, other bits (cores) ignored.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220610083549.16773-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The header file contains essential structure definitions, description of
bit fields and bits in the ipc4 header and an internally used ipc4 message
container definition.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://lore.kernel.org/r/20220505094818.10346-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
