ieee80211_add_gtk_rekey receives a keyconf as an argument, and the
cipher and keylen are taken from there to the new allocated key.
But in rekey, both the cipher and the keylen should be the same as of
the old key, so let ieee80211_add_gtk_rekey find those, so drivers won't
have to fill it in.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250721214922.3c5c023bfae9.Ie6594ae2b4b6d5b3d536e642b349046ebfce7a5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce the ability to parse the short beacon data and long
beacon period. The long beacon period represents the number of beacon
intervals between each long beacon transmission. Additionally,
as a BSS cannot change its configuration such that short beaconing
is dynamically disabled/enabled without tearing down the interface
- we ensure we have an existing short beacon before performing
the update.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250717074205.312577-3-lachlan.hodges@morsemicro.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When SAE commit is sent and received in response, there's no
ordering for the SAE confirm messages. As such, don't call
drivers to stop listening on the channel when the confirm
message is still expected.
This fixes an issue if the local confirm is transmitted later
than the AP's confirm, for iwlwifi (and possibly mt76) the
AP's confirm would then get lost since the device isn't on
the channel at the time the AP transmit the confirm.
For iwlwifi at least, this also improves the overall timing
of the authentication handshake (by about 15ms according to
the report), likely since the session protection won't be
aborted and rescheduled.
Note that even before this, mgd_complete_tx() wasn't always
called for each call to mgd_prepare_tx() (e.g. in the case
of WEP key shared authentication), and the current drivers
that have the complete callback don't seem to mind. Document
this as well though.
Reported-by: Jan Hendrik Farr <kernel@jfarr.cc>
Closes: https://lore.kernel.org/all/aB30Ea2kRG24LINR@archlinux/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250609213232.12691580e140.I3f1d3127acabcd58348a110ab11044213cf147d3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we get to the error path of ieee80211_prep_connection, for example
because of a FW issue, then ieee80211_vif_set_links is called
with 0.
But the call to drv_change_vif_links from ieee80211_vif_update_links
will probably fail as well, for the same reason.
In this case, the valid_links and active_links bitmaps will be reverted
to the value of the failing connection.
Then, in the next connection, due to the logic of
ieee80211_set_vif_links_bitmaps, valid_links will be set to the ID of
the new connection assoc link, but the active_links will remain with the
ID of the old connection's assoc link.
If those IDs are different, we get into a weird state of valid_links and
active_links being different. One of the consequences of this state is
to call drv_change_vif_links with new_links as 0, since the & operation
between the bitmaps will be 0.
Since a removal of a link should always succeed, ignore the return value
of drv_change_vif_links if it was called to only remove links, which is
the case for the ieee80211_prep_connection's error path.
That way, the bitmaps will not be reverted to have the value from the
failing connection and will have 0, so the next connection will have a
good state.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250609213231.ba2011fb435f.Id87ff6dab5e1cf757b54094ac2d714c656165059@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for updating the stations S1G capabilities when
an S1G association occurs.
Signed-off-by: Lachlan Hodges <lachlan.hodges@morsemicro.com>
Link: https://patch.msgid.link/20250617080610.756048-3-lachlan.hodges@morsemicro.com
[remove unused S1G_CAP3_MAX_MPDU_LEN_3895/_7791]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, per-radio attributes are set on per-phy basis, i.e., all the
radios present in a wiphy will take attributes values sent from user. But
each radio in a wiphy can get different values from userspace based on
its requirement.
To extend support to set per-radio attributes, add support to get radio
index from userspace. Add an NL attribute - NL80211_ATTR_WIPHY_RADIO_INDEX,
to get user specified radio index for which attributes should be changed.
Pass this to individual drivers, so that the drivers can use this radio
index to change per-radio attributes when necessary. Currently, per-radio
attributes identified are:
NL80211_ATTR_WIPHY_TX_POWER_LEVEL
NL80211_ATTR_WIPHY_ANTENNA_TX
NL80211_ATTR_WIPHY_ANTENNA_RX
NL80211_ATTR_WIPHY_RETRY_SHORT
NL80211_ATTR_WIPHY_RETRY_LONG
NL80211_ATTR_WIPHY_FRAG_THRESHOLD
NL80211_ATTR_WIPHY_RTS_THRESHOLD
NL80211_ATTR_WIPHY_COVERAGE_CLASS
NL80211_ATTR_TXQ_LIMIT
NL80211_ATTR_TXQ_MEMORY_LIMIT
NL80211_ATTR_TXQ_QUANTUM
By default, the radio index is set to -1. This means the attribute should
be treated as a global configuration. If the user has not specified any
index, then the radio index passed to individual drivers would be -1. This
would indicate that the attribute applies to all radios in that wiphy.
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Link: https://patch.msgid.link/20250615082312.619639-2-quic_rdevanat@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, link station statistics for MLO are filled by mac80211.
But there are some statistics that kept by mac80211 might not be
accurate, so let the driver pre-fill the link statistics. The driver
can fill the values (indicating which field is filled, by setting the
filled bitmapin in link_station structure).
Statistics that driver don't fill are filled by mac80211.
Hence, add link_sta_statistics callback to fill link station statistics
for MLO in sta_set_link_sinfo() by drivers.
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Link: https://patch.msgid.link/20250528054420.3050133-11-quic_sarishar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, in supporting API's to fill sinfo structure from sta
structure, is mapped to fill the fields from sta->deflink. However,
for multi-link (ML) station, sinfo structure should be filled from
corresponding link_id.
Therefore, add link_id as an additional argument in supporting API's
for filling sinfo structure correctly. Link_id is set to -1 for non-ML
station and corresponding link_id for ML stations. In supporting API's
for filling sinfo structure, check for link_id, if link_id < 0, fill
the sinfo structure from sta->deflink, otherwise fill from
sta->link[link_id].
Current, changes are done at the deflink level i.e, pass -1 as link_id.
Actual link_id will be added in subsequent patches to support
station statistics for MLO.
Signed-off-by: Sarika Sharma <quic_sarishar@quicinc.com>
Link: https://patch.msgid.link/20250528054420.3050133-2-quic_sarishar@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per IEEE 802.11be-2024 - 9.4.2.321, EHT operation element
contains MCS15 Disable subfield as the sixth bit, which is set when
MCS15 support is not enabled.
Get MCS15 support from EHT operation params and add it in link_conf
so that driver can use this value to know if EHT-MCS 15 reception
is enabled.
Co-developed-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Mohan Kumar G <quic_mkumarg@quicinc.com>
Link: https://patch.msgid.link/20250505152836.3266829-1-quic_mkumarg@quicinc.com
[remove pointless !! for bool assignment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For MBSSID, each vif (struct ieee80211_vif) stores another vif
pointer for the transmitting profile of MBSSID set. This won't
suffice for MLO as there may be multiple links, each of which can
be part of different MBSSID sets. Hence the information needs to
be stored per-link. Additionally, the transmitted profile itself
may be part of an MLD hence storing vif will not suffice either.
Fix MLO by storing an instance of struct ieee80211_bss_conf
for each link.
Modify following operations to reflect the above structure updates:
- channel switch completion
- BSS color change completion
- Removing nontransmitted links in ieee80211_stop_mbssid()
- drivers retrieving the transmitted link for beacon templates.
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Co-developed-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Co-developed-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Signed-off-by: Aloka Dixit <aloka.dixit@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408184501.3715887-3-aloka.dixit@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When an AP and Non-AP MLD operates in EMLSR mode, EML capabilities
advertised during Association contains information such as EMLSR
transition delay, padding delay and transition timeout values.
Save the EML capabilities information that is received during station
addition and capabilities update in ieee80211_sta so that drivers can use
it for triggering EMLSR operation.
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20250327051320.3253783-3-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 484a54c2e5. The CoDel
parameter change essentially disables CoDel on slow stations, with some
questionable assumptions, as Dave pointed out in [0]. Quoting from
there:
But here are my pithy comments as to why this part of mac80211 is so
wrong...
static void sta_update_codel_params(struct sta_info *sta, u32 thr)
{
- if (thr && thr < STA_SLOW_THRESHOLD * sta->local->num_sta) {
1) sta->local->num_sta is the number of associated, rather than
active, stations. "Active" stations in the last 50ms or so, might have
been a better thing to use, but as most people have far more than that
associated, we end up with really lousy codel parameters, all the
time. Mistake numero uno!
2) The STA_SLOW_THRESHOLD was completely arbitrary in 2016.
- sta->cparams.target = MS2TIME(50);
This, by itself, was probably not too bad. 30ms might have been
better, at the time, when we were battling powersave etc, but 20ms was
enough, really, to cover most scenarios, even where we had low rate
2Ghz multicast to cope with. Even then, codel has a hard time finding
any sane drop rate at all, with a target this high.
- sta->cparams.interval = MS2TIME(300);
But this was horrible, a total mistake, that is leading to codel being
completely ineffective in almost any scenario on clients or APS.
100ms, even 80ms, here, would be vastly better than this insanity. I'm
seeing 5+seconds of delay accumulated in a bunch of otherwise happily
fq-ing APs....
100ms of observed jitter during a flow is enough. Certainly (in 2016)
there were interactions with powersave that I did not understand, and
still don't, but if you are transmitting in the first place, powersave
shouldn't be a problemmmm.....
- sta->cparams.ecn = false;
At the time we were pretty nervous about ecn, I'm kind of sanguine
about it now, and reliably indicating ecn seems better than turning it
off for any reason.
[...]
In production, on p2p wireless, I've had 8ms and 80ms for target and
interval for years now, and it works great.
I think Dave's arguments above are basically sound on the face of it,
and various experimentation with tighter CoDel parameters in the OpenWrt
community have show promising results[1]. So I don't think there's any
reason to keep this parameter fiddling; hence this revert.
[0] https://lore.kernel.org/linux-wireless/CAA93jw6NJ2cmLmMauz0xAgC2MGbBq6n0ZiZzAdkK0u4b+O2yXg@mail.gmail.com/
[1] https://forum.openwrt.org/t/reducing-multiplexing-latencies-still-further-in-wifi/133605/130
Suggested-By: Dave Taht <dave.taht@gmail.com>
In-memory-of: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Link: https://patch.msgid.link/20250403183930.197716-1-toke@toke.dk
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will be used by the low level driver.
Note that link_id will be 0 in case of a non-MLO authentication.
Also fix a call-site of mgd_prepare_tx() where the link_id was not
populated.
Update the documentation to reflect the current state
ieee80211_prep_tx_info::link_id is also available in mgd_complete_tx().
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205110958.6a590f189ce5.I1fc5c0da26b143f5b07191eb592f01f7083d55ae@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a strict mode where we disable certain workarounds and have
additional checks such as, for now, that VHT capabilities from
association response match those from beacon/probe response. We
can extend the checks in the future.
Make it an opt-in setting by the driver so it can be set there
in some driver-specific way, for example. Also allow setting
this one hw flag through the hwflags debugfs, by writing a new
strict=0 or strict=1 value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205110958.5cecb0469479.I4a69617dc60ba0d6308416ffbc3102cfd08ba068@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for configuring EPCS state:
- When EPCS is enabled, send an EPCS enable request action frame
to the AP. When the AP replies with EPCS enable response, enable
EPCS by applying the QoS parameters provided by the AP. Do so for
all the valid MLD links. Once EPCS is enabled, support processing
of unsolicited EPCS enable response frames.
- When EPCS is disabled, send an EPCS teardown request to the AP
and apply the QoS parameters as obtained from the last received
beacons. Do so for all the valid links.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250205110958.7a90afd7e140.I3f602d65f5c1fd849d6c70b12307dda33aa91ccb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When in non-MLO mode, the key ID was set to -1 even for keys that are
not pairwise. Change the link ID to be the link ID of the deflink in
this case so that drivers do not need to special cases for this.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250102161730.0c066f084677.I4a5c288465e75119edb6a0df90dddf6f30d14a02@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to save power, it can be desirable to change the
RX operating mode using OMI to reduce the bandwidth. As the
handshake must be done in the HTC+ field, it cannot be done
by mac80211 directly, so expose functions to the driver to
request and finalize the necessary updates.
Note that RX OMI really only changes what the peer (AP) will
transmit to us, but in order to use it to actually save some
power (by reducing the listen bandwidth) we also update rate
scaling and then the channel context's mindef accordingly.
The updates are split into two in order to sequence them
correctly, when reducing bandwidth first reduce the rate
scaling and thus TX, then send OMI, then reduce the listen
bandwidth (chandef); when increasing bandwidth this is the
other way around. This also requires tracking in different
variables which part is applicable already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250101070249.2c1a1934bd73.I4e90fd503504e37f9eac5bdae62e3f07e7071275@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the sequence goes like this (among others):
1. flush all stations (including the AP ones) -> this will tell the
drivers to remove the stations
2. notify the driver the vif is not associated.
Which means that in between 1 and 2, the state is that the vif is
associated, but there is no AP station, which makes no sense, and may be
problematic for some drivers (for example iwlwifi)
Change the sequence to:
1. flush the TDLS stations
2. move the AP station to IEEE80211_STA_NONE
3. notify the driver about the vif being unassociated
4. flush the AP station
In order to not break other drivers, add a vif flag to indicate whether
the driver wants to new sequence or not. If the flag is not set, then
things will be done in the old sequence.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241224192322.996ad1be6cb3.I7815d33415aa1d65c0120b54be7a15a45388f807@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Multi-Link Operation implementation continues, both in stack and in
drivers. Otherwise it has been relatively quiet.
Major changes:
cfg80211/mac80211
* define wiphy guard
* get TX power per link
* EHT 320 MHz channel support for mesh
ath11k
* QCA6698AQ support
ath9k
* RX inactivity detection
rtl8xxxu
* add more USB device IDs
rtw88
* add more USB device IDs
* enable USB RX aggregation and USB 3 to improve performance
rtw89
* PowerSave flow for Multi-Link Operation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmdkbAoRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZuRIgf/dcjYr+eg3I7iU9qGxvEwHlDAC5CaMRwe
8+/SO6gy49xf6igleNQ2jBn/qAsJTiro6IzJwb1D6i16ax4TRUTEkTZSiYCzntKI
9Nkq59qhsRI4Vxrhp6NibUtVnjuRdSruVM5uLCccUCJ8tfq13WGhecR2pmV0TDO3
bRSza6L64XIuSmqHkuWS3Hz1YQvIvIZMeeiWoC35mtXg6ORRXpYloLtCzFn1zxoP
YPoeSfoAqIlaVwdB1DoaakU6is8oGZ0oI6zw/qaN8P7pYfqO62ATf6ZzAdwHE1dU
fow9nvwzln+BqgpdIK81QFR+XC+7LorCGSaQlYu6C0nxjSzycSrgOw==
=WIP7
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.14
Multi-Link Operation implementation continues, both in stack and in
drivers. Otherwise it has been relatively quiet.
Major changes:
cfg80211/mac80211
- define wiphy guard
- get TX power per link
- EHT 320 MHz channel support for mesh
ath11k
- QCA6698AQ support
ath9k
- RX inactivity detection
rtl8xxxu
- add more USB device IDs
rtw88
- add more USB device IDs
- enable USB RX aggregation and USB 3 to improve performance
rtw89
- PowerSave flow for Multi-Link Operation
* tag 'wireless-next-2024-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (121 commits)
wifi: wlcore: sysfs: constify 'struct bin_attribute'
wifi: brcmfmac: clarify unmodifiable headroom log message
wifi: brcmfmac: add missing header include for brcmf_dbg
wifi: brcmsmac: add gain range check to wlc_phy_iqcal_gainparams_nphy()
wifi: qtnfmac: fix spelling error in core.h
wifi: rtw89: phy: add dummy C2H event handler for report of TAS power
wifi: rtw89: 8851b: rfk: remove unnecessary assignment of return value of _dpk_dgain_read()
wifi: rtw89: 8852c: rfk: refine target channel calculation in _rx_dck_channel_calc()
wifi: rtlwifi: pci: wait for firmware loading before releasing memory
wifi: rtlwifi: fix memory leaks and invalid access at probe error path
wifi: rtlwifi: destroy workqueue at rtl_deinit_core
wifi: rtlwifi: remove unused check_buddy_priv
wifi: rtw89: 8922a: update format of RFK pre-notify H2C command v2
wifi: rtw89: regd: update regulatory map to R68-R51
wifi: rtw89: 8852c: disable ER SU when 4x HE-LTF and 0.8 GI capability differ
wifi: rtw89: disable firmware training HE GI and LTF
wifi: rtw89: ps: update data for firmware and settings for hardware before/after PS
wifi: rtw89: ps: refactor channel info to firmware before entering PS
wifi: rtw89: ps: refactor PS flow to support MLO
wifi: mwifiex: decrease timeout waiting for host sleep from 10s to 5s
...
====================
Link: https://patch.msgid.link/20241219185709.774EDC4CECE@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ML interfaces can have multiple affiliated links to it and
hence there is a need to report tx power of specified link
rather deflink.
Add changes to report tx power of requested link from mac80211,
also pass link id as an argument in get_tx_power op so that supported
drivers can use it to report link's tx power.
Co-developed-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Link: https://patch.msgid.link/20241125083217.216095-3-quic_ramess@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since adding support for opting out of virtual monitor support, a zero vif
addr was used to indicate passive vs active monitor to the driver.
This would break the vif->addr when changing the netdev mac address before
switching the interface from monitor to sta mode.
Fix the regression by adding a separate flag to indicate whether vif->addr
is valid.
Reported-by: syzbot+9ea265d998de25ac6a46@syzkaller.appspotmail.com
Fixes: 9d40f7e327 ("wifi: mac80211: add flag to opt out of virtual monitor support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/20241115115850.37449-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we got an unprotected action frame with CSA and then we heard the
beacon with the CSA IE, we'll block the queues with the CSA reason
twice. Since this reason is refcounted, we won't wake up the queues
since we wake them up only once and the ref count will never reach 0.
This led to blocked queues that prevented any activity (even
disconnection wouldn't reset the queue state and the only way to recover
would be to reload the kernel module.
Fix this by not refcounting the CSA reason.
It becomes now pointless to maintain the csa_blocked_queues state.
Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 414e090bc4 ("wifi: mac80211: restrict public action ECSA frame handling")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219447
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241119173108.5ea90828c2cc.I4f89e58572fb71ae48e47a81e74595cac410fbac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sequence of calls has changed, but the description is inconsistent.
So, fix the description.
Fixes: 188a1bf894 ("wifi: mac80211: re-order assigning channel in activate links")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Link: https://patch.msgid.link/20241101082143.11138-1-kevin_yang@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful for multi-radio devices that are capable of monitoring on
multiple channels simultanenously. When this flag is set, each monitor
interface is passed to the driver individually and can have a configured
channel.
The vif mac address for non-active monitor interfaces is cleared, in order
to allow the driver to tell them apart from active ones.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://patch.msgid.link/3c55505ee0cf0a5f141fbcb30d1e8be8d9f40373.1728462320.git-series.nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers might need to also do this calculation, no point in
them duplicating the code. Since it's so simple, just make
it an inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.af003cb4a088.I8b5d29504b726caae24af6013c65b3daebe842a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to update the right link information, call the update
rate_control_rate_update() with the right link_sta, and then
pass that through to the driver's sta_rc_update() method. The
software rate control still doesn't support it, but that'll be
skipped by not having a rate control ref.
Since it now operates on a link sta, rename the driver method.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.5851b6b5fd41.Ibdf50d96afa4b761dd9b9dfd54a1147e77a75329@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to track this. Make it available for them, and maintain
the value when beacons are received.
When link X receives a beacon, iterate the RNR elements and update all
the links with their respective data.
Track the link id that updated the data so that each link can know
whether the update came from its own beacon or from another link.
In case, the update came from the link's own beacon, always update the
updater link id.
The purpose is to let the low level driver know if a link is losing its
beacons. If link X is losing its beacons, it can still track the
bss_param_ch_cnt and know where the update came from.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.e2d8d1a722ad.I04b883daba2cd48e5730659eb62ca1614c899cbb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to indicate to the driver that an interface is about to be
added so that the driver could prepare its resources early if it needs
so.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241007144851.e0e8563e1c30.Ifccc96a46a347eb15752caefc9f4eff31f75ed47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
Currently DFS works under assumption there could be only one channel
context in the hardware. Hence, drivers just calls the function
ieee80211_radar_detected() passing the hardware structure. However, with
MLO, this obviously will not work since number of channel contexts will be
more than one and hence drivers would need to pass the channel information
as well on which the radar is detected.
Also, when radar is detected in one of the links, other link's CAC should
not be cancelled.
Hence, in order to support DFS with MLO, do the following changes -
* Add channel context conf pointer as an argument to the function
ieee80211_radar_detected(). During MLO, drivers would have to pass on
which channel context conf radar is detected. Otherwise, drivers could
just pass NULL.
* ieee80211_radar_detected() will iterate over all channel contexts
present and
* if channel context conf is passed, only mark that as radar
detected
* if NULL is passed, then mark all channel contexts as radar
detected
* Then as usual, schedule the radar detected work.
* In the worker, go over all the contexts again and for all such context
which is marked with radar detected, cancel the ongoing CAC by calling
ieee80211_dfs_cac_cancel() and then notify cfg80211 via
cfg80211_radar_event().
* To cancel the CAC, pass the channel context as well where radar is
detected to ieee80211_dfs_cac_cancel(). This ensures that CAC is
canceled only on the links using the provided context, leaving other
links unaffected.
This would also help in scenarios where there is split phy 5 GHz radio,
which is capable of DFS channels in both lower and upper band. In this
case, simultaneous radars can be detected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20240906064426.2101315-9-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers need to purge TX SKB when stopping. Using skb_queue_purge() can't
report TX status to mac80211, causing ieee80211_free_ack_frame() warns
"Have pending ack frames!". Export ieee80211_purge_tx_queue() for drivers
to not have to reimplement it.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240822014255.10211-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may at times want to iterate their stations with a function
which requires some non-atomic operations.
ieee80211_iterate_stations_mtx() introduces an API to iterate stations
while holding that wiphy's mutex. This allows the iterating function to
do non-atomic operations safely.
Signed-off-by: Rory Little <rory@candelatech.com>
Link: https://patch.msgid.link/20240806004024.2014080-2-rory@candelatech.com
[unify internal list iteration functions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce 'ieee80211_mgmt_ba()' to avoid code duplication between
'ieee80211_send_addba_resp()', 'ieee80211_send_addba_request()',
and 'ieee80211_send_delba()', ensure that all related addresses
are '__aligned(2)', and prefer convenient 'ether_addr_copy()'
over generic 'memcpy()'. No functional changes expected.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://patch.msgid.link/20240725090925.6022-1-dmantipov@yandex.ru
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.
Major changes:
cfg80211/mac80211
* remove DEAUTH_NEED_MGD_TX_PREP flag
* multiple radios per wiphy support
mac80211_hwsim
* multi-radio wiphy support
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
iwlwifi
* mvm: re-enable Multi-Link Operation (MLO)
* aggregation (A-MSDU) optimisations
rtw89
* preparation for RTL8852BE-VT support
* WoWLAN support for WiFi 6 chips
* 36-bit PCI DMA support
mt76
* mt7925 Multi-Link Operation (MLO) support
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmaPsBQRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt9EQf/Wevf/RnKyHhcuW4kmv0cxnjLW39K7CAh
ZlfN2JNTsVk4Na1EBjUgVyAWGdnGQpEhQlJYDExHcf5iD12pMVMIAQS8JXTDxuva
+ErAN1652p2N8nFCkNNuGbjYfO0D61xSIQj2uHhAlafK2k8FwnSn6XPP6jjHWvur
Acmw6W6l8eL+MP2K1VN2/2S09Gr6IQs7gXgWQX/6CaoK+OynFbUg8T9GQ2aqjr+d
lD17YB+oOHNCBxvg9LtBhKdfV14OBkKT6hW+YEqsrBEbx3N07ogDkPO0NUUPMXN3
IePEhj4XXrJ5UBMTvgWzNG9CwPeZFwuKGga+HZO9RKF5rwu42LsUMA==
=MpwE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.11
Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.
Major changes:
cfg80211/mac80211
* remove DEAUTH_NEED_MGD_TX_PREP flag
* multiple radios per wiphy support
mac80211_hwsim
* multi-radio wiphy support
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
iwlwifi
* mvm: re-enable Multi-Link Operation (MLO)
* aggregation (A-MSDU) optimisations
rtw89
* preparation for RTL8852BE-VT support
* WoWLAN support for WiFi 6 chips
* 36-bit PCI DMA support
mt76
* mt7925 Multi-Link Operation (MLO) support
* tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (204 commits)
wifi: mac80211: fix AP chandef capturing in CSA
wifi: iwlwifi: correctly reference TSO page information
wifi: mt76: mt792x: fix scheduler interference in drv own process
wifi: mt76: mt7925: enabling MLO when the firmware supports it
wifi: mt76: mt7925: remove the unused mt7925_mcu_set_chan_info
wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_basic_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_set_timing for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_phy_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_rate_ctrl_tlv for MLO
wifi: mt76: mt7925: add mt7925_mcu_sta_eht_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_update for MLO
wifi: mt76: mt7925: update mt7925_mcu_add_bss_info for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_mld_tlv for MLO
wifi: mt76: mt7925: add mt7925_[assign,unassign]_vif_chanctx
wifi: mt76: add def_wcid to struct mt76_wcid
wifi: mt76: mt7925: report link information in rx status
wifi: mt76: mt7925: update rate index according to link id
wifi: mt76: mt7925: add link handling in the mt7925_ipv6_addr_change
...
====================
Link: https://patch.msgid.link/20240711102353.0C849C116B1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the definition of BSS_CHANGED_UNSOL_BCAST_PROBE_RESP so that
not all higher bits get set, 1<<31 is a signed variable, so when
we do
u64 changed = BSS_CHANGED_UNSOL_BCAST_PROBE_RESP;
we get sign expansion, so the value is 0xffff'ffff'8000'0000 and
that's clearly not desired. Use BIT_ULL() to make it unsigned as
well as the right type for the change flags.
Fixes: 178e9d6adc ("wifi: mac80211: fix unsolicited broadcast probe config")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627104257.06174d291db2.Iba0d642916eb78a61f8ab2cc5ca9280783d9c1db@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This flag is annoying because it puts a lot of logic into mac80211
that could just as well be in the driver (only iwlmvm uses it) and
the implementation is also broken for MLO.
Remove the flag in favour of calling drv_mgd_prepare_tx() without
any conditions even for the deauth-while-assoc case. The drivers
that implement it can take the appropriate actions, which for the
only user of DEAUTH_NEED_MGD_TX_PREP (iwlmvm) is a bit more tricky
than the implementation in mac80211 is anyway, and all others have
no need and can just exit if info->was_assoc is set.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627132527.94924bcc9c9e.I328a219e45f2e2724cd52e75bb9feee3bf21a463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add flag for Full Bandwidth UL MU-MIMO for EHT. This is utilized
to pass EHT MU-MIMO configurations from user space to driver
in AP mode.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Link: https://msgid.link/20240515181327.12855-2-quic_pradeepc@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of passing the full TPE elements, in all their glory
and mixed up data formats for HE backward compatibility, parse
them fully into the right values, and pass that to the drivers.
Also introduce proper validation already in mac80211, so that
drivers don't need to do it, and parse the EHT portions.
The code now passes the values in the right order according to
the channel used by an interface, which could also be a subset
of the data advertised by the AP, if we couldn't connect with
the full bandwidth (for whatever reason.)
Also add kunit tests for the more complicated bits of it.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240506214536.2aa839969b60.I265b28209e0b29772b2f125f7f83de44a4da877b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
