Currently, BIS_LINK is used for both BIG sync and PA sync connections,
which makes it impossible to distinguish them when searching for a PA
sync connection.
Adding PA_LINK will make the distinction clearer and simplify future
extensions for PA-related features.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When the BIS source stops, the controller sends an LE BIG Sync Lost
event (subevent 0x1E). Currently, this event is not handled, causing
the BIS stream to remain active in BlueZ and preventing recovery.
Signed-off-by: Yang Li <yang.li@amlogic.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since commit 4aa42119d9 ("Bluetooth: Remove pending ACL connection
attempts") this function is unused.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Macro parameters should always be put into braces when accessing it.
Fixes: 4fc9857ab8 ("Bluetooth: hci_sync: Add check simultaneous roles support")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The provided macro parameter is named 'dev' (rather than 'hdev', which
may be a variable on the stack where the macro is used).
Fixes: a9a830a676 ("Bluetooth: hci_event: Fix sending HCI_OP_READ_ENC_KEY_SIZE")
Fixes: 6126ffabba ("Bluetooth: Introduce HCI_CONN_FLAG_DEVICE_PRIVACY device flag")
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The check for destination to be BDADDR_ANY is no longer necessary with
the introduction of BIS_LINK.
Fixes: 23205562ff ("Bluetooth: separate CIS_LINK and BIS_LINK link types")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
syzbot reported use-after-free in vhci_flush() without repro. [0]
From the splat, a thread close()d a vhci file descriptor while
its device was being used by iotcl() on another thread.
Once the last fd refcnt is released, vhci_release() calls
hci_unregister_dev(), hci_free_dev(), and kfree() for struct
vhci_data, which is set to hci_dev->dev->driver_data.
The problem is that there is no synchronisation after unlinking
hdev from hci_dev_list in hci_unregister_dev(). There might be
another thread still accessing the hdev which was fetched before
the unlink operation.
We can use SRCU for such synchronisation.
Let's run hci_dev_reset() under SRCU and wait for its completion
in hci_unregister_dev().
Another option would be to restore hci_dev->destruct(), which was
removed in commit 587ae086f6 ("Bluetooth: Remove unused
hci-destruct cb"). However, this would not be a good solution, as
we should not run hci_unregister_dev() while there are in-flight
ioctl() requests, which could lead to another data-race KCSAN splat.
Note that other drivers seem to have the same problem, for exmaple,
virtbt_remove().
[0]:
BUG: KASAN: slab-use-after-free in skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
BUG: KASAN: slab-use-after-free in skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
Read of size 8 at addr ffff88807cb8d858 by task syz.1.219/6718
CPU: 1 UID: 0 PID: 6718 Comm: syz.1.219 Not tainted 6.16.0-rc1-syzkaller-00196-g08207f42d3ff #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/07/2025
Call Trace:
<TASK>
dump_stack_lvl+0x189/0x250 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:408 [inline]
print_report+0xd2/0x2b0 mm/kasan/report.c:521
kasan_report+0x118/0x150 mm/kasan/report.c:634
skb_queue_empty_lockless include/linux/skbuff.h:1891 [inline]
skb_queue_purge_reason+0x99/0x360 net/core/skbuff.c:3937
skb_queue_purge include/linux/skbuff.h:3368 [inline]
vhci_flush+0x44/0x50 drivers/bluetooth/hci_vhci.c:69
hci_dev_do_reset net/bluetooth/hci_core.c:552 [inline]
hci_dev_reset+0x420/0x5c0 net/bluetooth/hci_core.c:592
sock_do_ioctl+0xd9/0x300 net/socket.c:1190
sock_ioctl+0x576/0x790 net/socket.c:1311
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:907 [inline]
__se_sys_ioctl+0xf9/0x170 fs/ioctl.c:893
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fcf5b98e929
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fcf5c7b9038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fcf5bbb6160 RCX: 00007fcf5b98e929
RDX: 0000000000000000 RSI: 00000000400448cb RDI: 0000000000000009
RBP: 00007fcf5ba10b39 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 0000000000000000 R14: 00007fcf5bbb6160 R15: 00007ffd6353d528
</TASK>
Allocated by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
poison_kmalloc_redzone mm/kasan/common.c:377 [inline]
__kasan_kmalloc+0x93/0xb0 mm/kasan/common.c:394
kasan_kmalloc include/linux/kasan.h:260 [inline]
__kmalloc_cache_noprof+0x230/0x3d0 mm/slub.c:4359
kmalloc_noprof include/linux/slab.h:905 [inline]
kzalloc_noprof include/linux/slab.h:1039 [inline]
vhci_open+0x57/0x360 drivers/bluetooth/hci_vhci.c:635
misc_open+0x2bc/0x330 drivers/char/misc.c:161
chrdev_open+0x4c9/0x5e0 fs/char_dev.c:414
do_dentry_open+0xdf0/0x1970 fs/open.c:964
vfs_open+0x3b/0x340 fs/open.c:1094
do_open fs/namei.c:3887 [inline]
path_openat+0x2ee5/0x3830 fs/namei.c:4046
do_filp_open+0x1fa/0x410 fs/namei.c:4073
do_sys_openat2+0x121/0x1c0 fs/open.c:1437
do_sys_open fs/open.c:1452 [inline]
__do_sys_openat fs/open.c:1468 [inline]
__se_sys_openat fs/open.c:1463 [inline]
__x64_sys_openat+0x138/0x170 fs/open.c:1463
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Freed by task 6535:
kasan_save_stack mm/kasan/common.c:47 [inline]
kasan_save_track+0x3e/0x80 mm/kasan/common.c:68
kasan_save_free_info+0x46/0x50 mm/kasan/generic.c:576
poison_slab_object mm/kasan/common.c:247 [inline]
__kasan_slab_free+0x62/0x70 mm/kasan/common.c:264
kasan_slab_free include/linux/kasan.h:233 [inline]
slab_free_hook mm/slub.c:2381 [inline]
slab_free mm/slub.c:4643 [inline]
kfree+0x18e/0x440 mm/slub.c:4842
vhci_release+0xbc/0xd0 drivers/bluetooth/hci_vhci.c:671
__fput+0x44c/0xa70 fs/file_table.c:465
task_work_run+0x1d1/0x260 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x6ad/0x22e0 kernel/exit.c:955
do_group_exit+0x21c/0x2d0 kernel/exit.c:1104
__do_sys_exit_group kernel/exit.c:1115 [inline]
__se_sys_exit_group kernel/exit.c:1113 [inline]
__x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1113
x64_sys_call+0x21ba/0x21c0 arch/x86/include/generated/asm/syscalls_64.h:232
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xfa/0x3b0 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The buggy address belongs to the object at ffff88807cb8d800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 88 bytes inside of
freed 1024-byte region [ffff88807cb8d800, ffff88807cb8dc00)
Fixes: bf18c7118c ("Bluetooth: vhci: Free driver_data on file release")
Reported-by: syzbot+2faa4825e556199361f9@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=f62d64848fc4c7c30cd6
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently bc_sid is being ignore when acting as Broadcast Source role,
so this fix it by passing the bc_sid and then use it when programming
the PA:
< HCI Command: LE Set Exte.. (0x08|0x0036) plen 25
Handle: 0x01
Properties: 0x0000
Min advertising interval: 140.000 msec (0x00e0)
Max advertising interval: 140.000 msec (0x00e0)
Channel map: 37, 38, 39 (0x07)
Own address type: Random (0x01)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
TX power: Host has no preference (0x7f)
Primary PHY: LE 1M (0x01)
Secondary max skip: 0x00
Secondary PHY: LE 2M (0x02)
SID: 0x01
Scan request notifications: Disabled (0x00)
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use separate link type id for unicast and broadcast ISO connections.
These connection types are handled with separate HCI commands, socket
API is different, and hci_conn has union fields that are different in
the two cases, so they shall not be mixed up.
Currently in most places it is attempted to distinguish ucast by
bacmp(&c->dst, BDADDR_ANY) but it is wrong as dst is set for bcast sink
hci_conn in iso_conn_ready(). Additionally checking sync_handle might be
OK, but depends on details of bcast conn configuration flow.
To avoid complicating it, use separate link types.
Fixes: f764a6c2c1 ("Bluetooth: ISO: Add broadcast support")
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Although commit 75ddcd5ad4 ("Bluetooth: btusb: Configure altsetting
for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out
SCO data through USB Bluetooth chips, it's observed that with the patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
To address the issue above one needs to reset the altsetting back to
zero when there is no active SCO connection, which is the same as the
BlueZ behavior, and another benefit is the bus doesn't need to reserve
bandwidth when no SCO connection.
This patch adds the infrastructure that allow the user space program to
talk to Bluetooth drivers directly:
- Define the new packet type HCI_DRV_PKT which is specifically used for
communication between the user space program and the Bluetooth drviers
- hci_send_frame intercepts the packets and invokes drivers' HCI Drv
callbacks (so far only defined for btusb)
- 2 kinds of events to user space: Command Status and Command Complete,
the former simply returns the status while the later may contain
additional response data.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This fixes the regression introduced by 50c1241e6a8a ("Bluetooth: l2cap:
Check encryption key size on incoming connection") introduced a check for
l2cap_check_enc_key_size which checks for hcon->enc_key_size which may
not be initialized if HCI_OP_READ_ENC_KEY_SIZE is still pending.
If the key encryption size is known, due previously reading it using
HCI_OP_READ_ENC_KEY_SIZE, then store it as part of link_key/smp_ltk
structures so the next time the encryption is changed their values are
used as conn->enc_key_size thus avoiding the racing against
HCI_OP_READ_ENC_KEY_SIZE.
Now that the enc_size is stored as part of key the information the code
then attempts to check that there is no downgrade of security if
HCI_OP_READ_ENC_KEY_SIZE returns a value smaller than what has been
previously stored.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220061
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220063
Fixes: 522e9ed157 ("Bluetooth: l2cap: Check encryption key size on incoming connection")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
BIG Create Sync requires the command to just generates a status so this
makes use of __hci_cmd_sync_status_sk to wait for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the BIG sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EVT_LE_BIG_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 42ecf19471 ("Bluetooth: ISO: Do not emit LE BIG Create Sync if previous is pending")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Broadcast Receiver requires creating PA sync but the command just
generates a status so this makes use of __hci_cmd_sync_status_sk to wait
for HCI_EV_LE_PA_SYNC_ESTABLISHED, also because of this chance it is not
longer necessary to use a custom method to serialize the process of
creating the PA sync since the cmd_work_sync itself ensures only one
command would be pending which now awaits for
HCI_EV_LE_PA_SYNC_ESTABLISHED before proceeding to next connection.
Fixes: 4a5e0ba686 ("Bluetooth: ISO: Do not emit LE PA Create Sync if previous is pending")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Support enabling TX timestamping for some skbs, and track them until
packet completion. Generate software SCM_TSTAMP_COMPLETION when getting
completion report from hardware.
Generate software SCM_TSTAMP_SND before sending to driver. Sending from
driver requires changes in the driver API, and drivers mostly are going
to send the skb immediately.
Make the default situation with no COMPLETION TX timestamping more
efficient by only counting packets in the queue when there is nothing to
track. When there is something to track, we need to make clones, since
the driver may modify sent skbs.
The tx_q queue length is bounded by the hdev flow control, which will
not send new packets before it has got completion reports for old ones.
Signed-off-by: Pauli Virtanen <pav@iki.fi>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some fake controllers cannot be initialized because they return a smaller
report than expected for READ_VOICE_SETTING.
Signed-off-by: Pedro Nishiyama <nishiyama.pedro@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
mgmt_start_discovery_complete() and mgmt_stop_discovery_complete() last
uses were removed in 2022 by
commit ec2904c259 ("Bluetooth: Remove dead code from hci_request.c")
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 4d94f05558 which has
problems (see [1]) and is no longer needed since 581dd2dc16
("Bluetooth: hci_event: Fix using rcu_read_(un)lock while iterating")
has reworked the code where the original bug has been found.
[1] Link: https://lore.kernel.org/linux-bluetooth/877c55ci1r.wl-tiwai@suse.de/T/#t
Fixes: 4d94f05558 ("Bluetooth: hci_core: Fix sleeping function called from invalid context")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hdev->reset is never used now and the hdev->cmd_timeout actually
does reset. This patch changes the call path from
hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset
, to
hdev->reset -> vendor_reset -> btusb_reset
Which makes it clear when we export the hdev->reset to a wider usage
e.g. allowing reset from sysfs.
This patch doesn't introduce any behavior change.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
hci_bdaddr_list_del_with_flags() was added in 2020's
commit 8baaa4038e ("Bluetooth: Add bdaddr_list_with_flags for classic
whitelist")
but has remained unused.
hci_remove_ext_adv_instance() was added in 2020's
commit eca0ae4aea ("Bluetooth: Add initial implementation of BIS
connections")
but has remained unused.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This marks LL Privacy as stable by removing its experimental UUID and
move its functionality to Device Flag (HCI_CONN_FLAG_ADDRESS_RESOLUTION)
which can be set by MGMT Device Set Flags so userspace retain control of
the feature.
Link: https://github.com/bluez/bluez/issues/1028
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Currently, hci_conn_hash_lookup_big only checks for BIS master connections,
by filtering out connections with the destination address set. This commit
updates this function to also consider BIS slave connections, since it is
also used for a Broadcast Receiver to set an available BIG handle before
issuing the LE BIG Create Sync command.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Bluetooth Core spec does not allow a LE BIG Create sync command to be
sent to Controller if another one is pending (Vol 4, Part E, page 2586).
In order to avoid this issue, the HCI_CONN_CREATE_BIG_SYNC was added
to mark that the LE BIG Create Sync command has been sent for a hcon.
Once the BIG Sync Established event is received, the hcon flag is
erased and the next pending hcon is handled.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Bluetooth Core spec does not allow a LE PA Create sync command to be
sent to Controller if another one is pending (Vol 4, Part E, page 2493).
In order to avoid this issue, the HCI_CONN_CREATE_PA_SYNC was added
to mark that the LE PA Create Sync command has been sent for a hcon.
Once the PA Sync Established event is received, the hcon flag is
erased and the next pending hcon is handled.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds quirks for broken extended create connection,
and write auth payload timeout.
Signed-off-by: Danil Pylaev <danstiv404@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If HCI_CONN_MGMT_CONNECTED has been set then the event shall be
HCI_CONN_MGMT_DISCONNECTED.
Fixes: b644ba3369 ("Bluetooth: Update device_connected and device_found events to latest API")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This inverts the LE State quirk so by default we assume the controllers
would report valid states rather than invalid which is how quirks
normally behave, also this would result in HCI command failing it the LE
States are really broken thus exposing the controllers that are really
broken in this respect.
Link: https://github.com/bluez/bluez/issues/584
Fixes: 220915857e ("Bluetooth: Adding driver and quirk defs for multi-role LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove unused and set but otherwise unused 'discovery_old_state'
and 'sco_last_tx' members of 'struct hci_dev'. The first one is
a leftover after commit 182ee45da0 ("Bluetooth: hci_sync: Rework
hci_suspend_notifier"); the second one is originated from ancient
2.4.19 and I was unable to find any actual use since that.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
After commit 78db544b5d ("Bluetooth: hci_core: Remove le_restart_scan
work"), 'scan_start' and 'scan_duration' of 'struct discovery_state'
are still initialized but actually unused. So remove the aforementioned
fields and adjust 'hci_discovery_filter_clear()' and 'le_scan_disable()'
accordingly. Compile tested only.
Fixes: 78db544b5d ("Bluetooth: hci_core: Remove le_restart_scan work")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When HCI raw sockets are opened, the Bluetooth kernel module doesn't
track CIS/BIS connections. User-space applications have to identify
ISO data by maintaining connection information and look up the mapping
for each ACL data packet received. Besides, btsnoop log captured in
kernel couldn't tell ISO data from ACL data in this case.
To avoid additional lookups, this patch introduces vendor-specific
packet classification for Intel BT controllers to distinguish
ISO data packets from ACL data packets.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This removes the bogus check for max > hcon->le_conn_max_interval since
the later is just the initial maximum conn interval not the maximum the
stack could support which is really 3200=4000ms.
In order to pass GAP/CONN/CPUP/BV-05-C one shall probably enter values
of the following fields in IXIT that would cause hci_check_conn_params
to fail:
TSPX_conn_update_int_min
TSPX_conn_update_int_max
TSPX_conn_update_peripheral_latency
TSPX_conn_update_supervision_timeout
Link: https://github.com/bluez/bluez/issues/847
Fixes: e4b019515f ("Bluetooth: Enforce validation on max value of connection interval")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If hdev->le_num_of_adv_sets is set to 1 it means that only handle 0x00
can be used, but since the MGMT interface instances start from 1
(instance 0 means all instances in case of MGMT_OP_REMOVE_ADVERTISING)
the code needs to map the instance to handle otherwise users will not be
able to advertise as instance 1 would attempt to use handle 0x01.
Fixes: 1d0fac2c38 ("Bluetooth: Use controller sets when available")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since BT_HS has been remove HCI_AMP controllers no longer has any use so
remove it along with the capability of creating AMP controllers.
Since we no longer need to differentiate between AMP and Primary
controllers, as only HCI_PRIMARY is left, this also remove
hdev->dev_type altogether.
Fixes: e7b02296fb ("Bluetooth: Remove BT_HS")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In case of a Broadcast Source that has PA enabled but no active BIG,
a Broadcast Sink needs to establish PA sync and parse BASE from PA
reports.
This commit moves the allocation of a PA sync hcon from the BIGInfo
advertising report event to the PA sync established event. After the
first complete PA report, the hcon is notified to the ISO layer. A
child socket is allocated and enqueued in the parent's accept queue.
BIGInfo reports also need to be processed, to extract the encryption
field and inform userspace. After the first BIGInfo report is received,
the PA sync hcon is notified again to the ISO layer. Since a socket will
be found this time, the socket state will transition to BT_CONNECTED and
the userspace will be woken up using sk_state_change.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds proper definitions for scan interval and window and then make
use of them instead their values.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The code shall always check if HCI_QUIRK_BROKEN_READ_ENC_KEY_SIZE has
been set before attempting to use HCI_OP_READ_ENC_KEY_SIZE.
Fixes: c569242cd4 ("Bluetooth: hci_event: set the conn encrypted before conn establishes")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The extended advertising reports do report the PHYs so this store then
in hci_conn so it can be later used in hci_le_ext_create_conn_sync to
narrow the PHYs to be scanned since the controller will also perform a
scan having a smaller set of PHYs shall reduce the time it takes to
find and connect peers.
Fixes: 288c90224e ("Bluetooth: Enable all supported LE PHY by default")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In a few cases the stack may generate commands as responses to events
which would happen to overwrite the sent_cmd, so this attempts to store
the request in req_skb so even if sent_cmd is replaced with a new
command the pending request will remain in stored in req_skb.
Fixes: 6a98e3836f ("Bluetooth: Add helper for serialized HCI command execution")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support to reassemble PA data for a Broadcast Sink
listening socket. This is needed in case the BASE is received
fragmented in multiple PA reports.
PA data is first reassembled inside the hcon, before the BASE
is extracted and stored inside the socket. The length of the
le_per_adv_data hcon array has been raised to 1650, to accommodate
the maximum PA data length that can come fragmented, according to
spec.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This creates a hcon instance at bis listen, before the PA sync
procedure is started.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If connection is still queued/pending in the cmd_sync queue it means no
command has been generated and it should be safe to just dequeue the
callback when it is being aborted.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This aligns the use socket sk_timeo as conn_timeout when initiating a
connection and then use it when scheduling the resulting HCI command,
that way the command is actually aborted synchronously thus not
blocking commands generated by hci_abort_conn_sync to inform the
controller the connection is to be aborted.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
With the last commit we moved to using the hci_sync queue for "Create
Connection" requests, removing the need for retrying the paging after
finished/failed "Create Connection" requests and after the end of
inquiries.
hci_conn_check_pending() was used to trigger this retry, we can remove it
now.
Note that we can also remove the special handling for COMMAND_DISALLOWED
errors in the completion handler of "Create Connection", because "Create
Connection" requests are now always serialized.
This is somewhat reverting commit 4c67bc74f0 ("[Bluetooth] Support
concurrent connect requests").
With this, the BT_CONNECT2 state of ACL hci_conn objects should now be
back to meaning only one thing: That we received a "Connection Request"
from another device (see hci_conn_request_evt), but the response to that
is going to be deferred.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>