Update the PHY settings to align with the latest PCIe PHY
Hardware Programming Guide for both PCIe controllers on the
SA8775P platform.
Add the ln_shrd region for SA8775P, incorporating new register
writes as specified in the updated Hardware Programming Guide.
Update pcs table for QCS8300, since both QCS8300 and SA8775P are
closely related and share same pcs settings.
Signed-off-by: Mrinmay Sarkar <mrinmay.sarkar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250617-update_phy-v5-1-2df83ed6a373@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe PHYs on x1e80100 do not a have a qref supply so stop requesting
one. This also avoids the follow warning at boot:
qcom-qmp-pcie-phy 1be0000.phy: supply vdda-qref not found, using dummy regulator
Fixes: e961ec81a3 ("phy: qcom: qmp: Add phy register and clk setting for x1e80100 PCIe3")
Cc: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20250429075440.19901-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some QCOM PCIe PHYs support no_csr reset. Unlike BCR reset which resets the
whole PHY (hardware and register), no_csr reset only resets PHY hardware
but retains register values, which means PHY setting can be skipped during
PHY init if PCIe link is enabled in bootloader and only no_csr is toggled
after that.
Hence, determine whether the PHY has been enabled in bootloader by
verifying QPHY_START_CTRL register. If it's programmed and no_csr reset is
available, skip BCR reset and PHY register setting to establish the PCIe
link with bootloader - programmed PHY settings.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Link: https://lore.kernel.org/r/20250411113120.651363-3-quic_wenbyao@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Decide the in-driver logic based on whether the nocsr reset is present
and defer checking the appropriateness of that to dt-bindings to save
on boilerplate.
Reset controller APIs are fine consuming a nullptr, so no additional
checks are necessary there.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Wenbin Yao <quic_wenbyao@quicinc.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Link: https://lore.kernel.org/r/20250411113120.651363-2-quic_wenbyao@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY for qcs8300 has a lot of difference with sa8775p.
So the qcs8300_qmp_gen4x2_pcie_rx_alt_tbl for qcs8300 is added.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Ziyue Zhang <quic_ziyuzhan@quicinc.com>
Link: https://lore.kernel.org/r/20250310063103.3924525-3-quic_ziyuzhan@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add a new, common configuration for Gen4x4 V6 PHYs without an init
sequence.
The bootloader configures the hardware once and the OS retains that
configuration by using the NOCSR reset line (which doesn't drop
register state on assert) in place of the "full reset" one.
Use this new configuration for X1P42100's Gen4x4 PHY.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250203-topic-x1p4_dts-v2-3-72cd4cdc767b@oss.qualcomm.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCS_LANE1 region isn't a part of the PCS_PCIE region. It was handled
this way as it simplified handled of devices with the old bindings.
Nowadays it can be handled as is, without hacks.
Split the PCS_LANE1 region from the PCS_PCIE / PCS_MISC region space.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241021-sar2130p-phys-v2-4-d883acf170f7@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2 support,
X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP UFS PHY
support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
- Updates
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array update
for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmdG0uwACgkQfBQHDyUj
g0ftFg//ftcsFV6HQp+MXTzgBrlXk1EbIXSfG1R1k2jSSzwUMgQkNkIXJ9bUVSRA
yvgn+JJ2OtoIBYVVyNbDghw6CBYc7TMcK+1PPcS43o63X/giXiQ+QLN+J19PxDOl
fgDvRgp4SHxWW3DAQW0Kgle7VCTWBIHCR3C06RG7I2AlIoWyzkNsI4SM8hSrnaon
9FzBqGZCSnGgorfUgEkWjv4TDK69xZOOG1bIbsX/xA1wY3vvRzJg3R7TGYqC35/F
XII5oHpv0kBjNwZhU4xR5YF6IDqakRa5UNviXi7DKzbyD277lkrCCccvq0EU4Vau
m7bv3nNTUKqk/EQBSEWCDYECD5Xw57Qa6i/qo3gMXIVoDm6jfUDP3MbPG0IllLBZ
+X34i1pq24gZLl+2rSMHMi8IlyTrpCgBsCeH/xsgkEev6Sr9gHI9Hqd1mnMHNa3G
U31kaY/eEfDy377k2l8hFKx3pT+Qsne9jbjOzdIuciL10+0xqwCOCrAJA6JjyxTI
ONcbRZRIwHAg48gPyMmqRXd5xnr+8epCedaRo0j4O8gJpSBCXzXCIIS3DlBlwmIc
WJkF5jN6WGunmI5yYd19256gVK2SPv0YA+UNFeQDF6d9djHaGaKvH2Is4zMe3JOW
mBfYwJLC39d8v3u4rBNSAR8a1HM9haAdcNctkrNmONMEtS9hsg0=
=5o8/
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hardware support:
- ST STM32MP25 combophy support
- Sparx5 support for lan969x serdes and updates to driver to support
this
- NXP PTN3222 eUSB2 to USB2 redriver
- Qualcomm SAR2130P eusb2 support, QCS8300 USB DW3 and QMP USB2
support, X1E80100 QMP PCIe PHY Gen4 support, QCS615 and QCS8300 QMP
UFS PHY support and SA8775P eDP PHY support
- Rockchip rk3576 usbdp and rk3576 usb2 phy support
- Binding for Microchip ATA6561 can phy
Updates:
- Freescale driver updates from hdmi support
- Conversion of rockchip rk3228 hdmi phy binding to yaml
- Broadcom usb2-phy deprecated support dropped and USB init array
update for BCM4908
- TI USXGMII mode support in J7200
- Switch back to platform_driver::remove() subsystem update"
* tag 'phy-for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (59 commits)
phy: qcom: qmp: Fix lecacy-legacy typo
phy: lan969x-serdes: add support for lan969x serdes driver
dt-bindings: phy: sparx5: document lan969x
phy: sparx5-serdes: add support for branching on chip type
phy: sparx5-serdes: add indirection layer to register macros
phy: sparx5-serdes: add function for getting the CMU index
phy: sparx5-serdes: add ops to match data
phy: sparx5-serdes: add constant for the number of CMU's
phy: sparx5-serdes: add constants to match data
phy: sparx5-serdes: add support for private match data
phy: bcm-ns-usb2: drop support for old binding variant
dt-bindings: phy: bcm-ns-usb2-phy: drop deprecated variant
dt-bindings: phy: Add QMP UFS PHY compatible for QCS8300
dt-bindings: phy: qcom: snps-eusb2: Add SAR2130P compatible
dt-bindings: phy: ti,tcan104x-can: Document Microchip ATA6561
phy: airoha: Fix REG_CSR_2L_RX{0,1}_REV0 definitions
phy: airoha: Fix REG_CSR_2L_JCPLL_SDM_HREN config in airoha_pcie_phy_init_ssc_jcpll()
phy: airoha: Fix REG_PCIE_PMA_TX_RESET config in airoha_pcie_phy_init_csr_2l()
phy: airoha: Fix REG_CSR_2L_PLL_CMN_RESERVE0 config in airoha_pcie_phy_init_clk_out()
phy: phy-rockchip-samsung-hdptx: Don't request RST_PHY/RST_ROPLL/RST_LCPLL
...
The PCIe PHYs on x1e80100 do not a have a qref supply so stop requesting
one. This also avoids the follow warning at boot:
qcom-qmp-pcie-phy 1bfc000.phy: supply vdda-qref not found, using dummy regulator
Fixes: 9dab00ee95 ("phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100")
Fixes: 606060ce8f ("phy: qcom-qmp-pcie: Add support for X1E80100 g3x2 and g4x2 PCIE")
Cc: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241015121406.15033-1-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Currently driver supports only x4 lane based functionality using tx/rx and
tx2/rx2 pair of register sets. To support 8 lane functionality with PCIe3,
PCIe3 related QMP PHY provides additional programming which are available
as txz and rxz based register set. Hence add txz and rxz based registers
usage and programming sequences.
As soon as software programs the txz and rxz based register set, hardware
shall "broadcast" the same settings to the tx/rx pair of registers for all
the 8 lanes, which saves the effort of software programming them one by
one.
There might be some tx and/or rx registers on some lanes need minor tweaks,
program them after programming the txz and rxz reigster set.
In addition, x1e80100 uses QMP PHY ver 6.30 for PCIe Gen4 x8, hence add
two new header files to reflect the new register offsets.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Link: https://lore.kernel.org/r/20241017030412.265000-5-quic_qianyu@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- New Support
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
- Removal
- obsolete qcom,usb-8x16-phy bindings
- Updates
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE+vs47OPLdNbVcHzyfBQHDyUjg0cFAmbv994ACgkQfBQHDyUj
g0eefhAApn1pj3AVJE+YBBNcRAZncxt/KdZmS0U8ErwVqlVbFCDJGJtCHOaKbPK+
K8c/u7vcElMA+JsqXd2biidlKsCmrkrpqqpPGJ08RlVy5TCa5H3UNONShPxU13g6
rP90CDJ6LpkOuU+p4b2jCVLVmY4Nq0g02OWUvuZDhFvR9FmfSVbRArmqWk+TdUW+
qO0oxxasNbh3nzt5HBwPUM+K2zZIzC7kQeJch69v3ETHeHzdGOlTKWEonU1OGnE9
PoeXubeSYW+fYaUbOg4n2Wgqt8330W3Flrhkd5Qp9cMAJEOe4Lqso3ai3jFW+iN4
bHQDcH3hzSpPNmlt2x8NgDamx/BEMbyAPQdnfVh7x4esxv+Zy/Fmg3XPeGf5BzlT
acis1nlAGnk/CpK+MurXgir8Si7gaiHH0n7lrginxr4QhBlT65Wzci0tPOYdivRH
4g8trmbLHX06Cji2XYvEjgm+Igekdyz892D6rSjOwYZS18CGgeJkdwVfyoMh984l
OVaU2d8N73J5UrP4zfUQV/FoOpqS6r+CbI0+f2CyPG+u6/Lwm7PT33ZZFof2s8/4
IiefpuwAzlPr8DEWa0j90VIGmVaTgmdYq3gdfRiG6P6fXoMkKMPLUbmZ9vFFMqRI
FiIe8K9gIyCRQadtUasUuVZ9vXr0jOHnbvCCbTmYSO/ceh+KU9I=
=XJmz
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New hw support:
- Rcar usb2 support for RZ/G3S SoC
- Nuvoton MA35 SoC USB 2.0 PHY driver
Removed:
- obsolete qcom,usb-8x16-phy bindings
Updates:
- 4 lane PCIe support for Qualcomm X1E80100
- Constify structure in subsystem update
- Subsystem simplification with scoped for each OF child loop update
- Yaml conversion for Qualcomm sata phy, Hiilicon hi3798cv200-combphy
bindings"
* tag 'phy-for-6.12' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (40 commits)
phy: renesas: rcar-gen3-usb2: Add support for the RZ/G3S SoC
dt-bindings: phy: renesas,usb2-phy: Document RZ/G3S phy bindings
phy: renesas: rcar-gen3-usb2: Add support to initialize the bus
phy: ti: j721e-wiz: Simplify with scoped for each OF child loop
phy: ti: j721e-wiz: Drop OF node reference earlier for simpler code
phy: ti: gmii-sel: Simplify with dev_err_probe()
phy: ti: am654-serdes: Use scoped device node handling to simplify error paths
phy: qcom: qmp-pcie-msm8996: Simplify with scoped for each OF child loop
phy: mediatek: xsphy: Simplify with scoped for each OF child loop
phy: mediatek: tphy: Simplify with scoped for each OF child loop
phy: hisilicon: usb2: Simplify with scoped for each OF child loop
phy: cadence: sierra: Simplify with scoped for each OF child loop
phy: broadcom: brcm-sata: Simplify with scoped for each OF child loop
phy: broadcom: bcm-cygnus-pcie: Simplify with scoped for each OF child loop
phy: nuvoton: add new driver for the Nuvoton MA35 SoC USB 2.0 PHY
dt-bindings: phy: nuvoton,ma35-usb2-phy: add new bindings
phy: qcom: qmp-pcie: Configure all tables on port B PHY
phy: airoha: adjust initialization delay in airoha_pcie_phy_init()
dt-bindings: phy: socionext,uniphier: add top-level constraints
phy: qcom: qmp-pcie: Add Gen4 4-lanes mode for X1E80100
...
Currently, only the RX and TX tables are written to the second PHY
(port B) when the 4-lanes mode is configured, but according to Qualcomm
internal documentation, the pcs, pcs_misc, serdes and ln_shrd tables need
to be written as well.
Signed-off-by: Qiang Yu <quic_qianyu@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20240805-phy-qcom-qmp-pcie-write-all-tbls-second-port-v3-1-6967c6bf61d1@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sixth PCIe controller on X1E80100 can be used in either
4-lanes mode or 2-lanes mode. Add the configuration and compatible
for the 4-lane mode.
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240823-x1e80100-phy-add-gen4x4-v3-2-b7765631ca01@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
These register prints are useful to validate the init sequence against the
Qcom internal documentation and also to share with the Qcom hw engineers to
debug issues related to PHY.
Sample debug prints:
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_SYSCLK_EN_SEL Offset: 0x0094 Val: 0xd9
qcom-qmp-pcie-phy 1c0e000.phy: Writing Reg: QSERDES_V5_COM_HSCLK_SEL Offset: 0x0158 Val: 0x11
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240731152548.102987-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Existing device trees specify only a single clock-output-name for the
PCIe PHYs. The function phy_aux_clk_register() expects a second entry in
that property. When it doesn't find it, it returns an error, thus
failing the probe of the PHY and thus breaking support for the
corresponding PCIe host.
Follow the approach of the combo USB+DT PHY and generate the name for
the AUX clocks instead of requiring it in DT.
Fixes: 583ca9ccfa ("phy: qcom: qmp-pcie: register second optional PHY AUX clock")
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240614-fix-pcie-phy-compat-v3-1-730d1811acf4@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for a single-lane and two-lane PCIe PHYs
found on Qualcomm IPQ9574 platform.
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: devi priya <quic_devipriy@quicinc.com>
Link: https://lore.kernel.org/r/20240516032436.2681828-5-quic_devipriy@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for x4 lane end point mode PHY found on sa8755p platform.
Reusing existing serdes and pcs_misc table for EP and moved
BIAS_EN_CLKBUFLR_EN register from RC serdes table to common serdes
table as this register is part of both RC and EP.
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1714494089-7917-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
enable this second clock by setting the proper 20MHz hardware rate in
the Gen4x2 SM8[456]50 aux_clock_rate config fields.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-4-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
add the code to register it for PHYs configs that sets a aux_clock_rate.
In order to get the right clock, add qmp_pcie_clk_hw_get() which uses
the newly introduced QMP_PCIE_PIPE_CLK & QMP_PCIE_PHY_AUX_CLK clock
IDs and also supports the legacy bindings by returning the PIPE clock
when #clock-cells=0.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-3-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe Gen4x2 PHY found in the SM8[456]50 SoCs have a second clock,
in order to expose it, split the current clock registering in two parts:
- CCF clock registering
- DT clock registering
Keep the of_clk_add_hw_provider/devm_add_action_or_reset to keep
compatibility with the legacy subnode bindings.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240322-topic-sm8x50-upstream-pcie-1-phy-aux-clk-v2-2-3ec0a966d52f@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For consistency, add the QMP v6 registers layout even though
they are the same as v5. Also switch all QMP v6 PHYs to use this
new layout.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231223-x1e80100-phy-pcie-v2-2-223c0556908a@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reuse sm8250 configuration to add support for both single lane and dual
lane PCIe PHYs on the Qualcomm SM8150 platform.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-8-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Populate offsets configuration for the rest of UFS PHYs to make it
possible to switch them to the new (single-node) bindings style.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-7-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For some of existing PHYs for new binding we are going to change refgen
to more correct "rchng". Rather than introducing additional code
to handle legacy vs current bindings (and clock names), use
devm_clk_bulk_get_optional().
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In order to simplify adding new PHY configurations, keep register
offset structs sorted by the version.
Fixes: a05b6d5135 ("phy: qcom-qmp-pcie: add support for sa8775p")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no shared lane config for v5.20 PHYs, it is only present on
SM8550 gen4x2.
Fixes: a05b6d5135 ("phy: qcom-qmp-pcie: add support for sa8775p")
Cc: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230820142035.89903-4-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The SDM845 QHP PHY doesn't have designated RX region. Corresponding RX
table is empty, so we can drop it completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230331151250.4049-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The PCIe PHY version used in SDX65 is v5.20 which has different register
offsets compared to the v5.0x and v4.0x PHYs. So separate register defines are
used for init sequence and PHY status.
Signed-off-by: Rohit Agarwal <quic_rohiagar@quicinc.com>
Link: https://lore.kernel.org/r/1679035114-19879-3-git-send-email-quic_rohiagar@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add PCIe RC init sequence making use of the common init sequence. The RC
mode additionally requires REFCLK_DRV_DSBL bit to set during powerup and
powerdown.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230308082424.140224-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In preparation for adding RC support, let's split out the EP related init
sequence so that the common sequence could be reused by RC as well.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230308082424.140224-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the SM8550 both g4 and g3 configurations. In addition, there is a
new "lane shared" table that needs to be configured for g4, along with
the No-CSR list of resets. The no-CSR allows resetting the PHY without
actually dropping the PHY configuration. The no-CSR needs to be
deasserted only after the PHY has been configured and the PLL has
stabilized.
Co-developed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230208180020.2761766-9-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new SM8550 SoC bumps up the HW version of QMP phy to v6.20 for
PCIE g4x2. Add the new PCS PCIE specific offsets in a dedicated
header file.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230208180020.2761766-6-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS PCIE specific offsets in a dedicated
header file.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230208180020.2761766-5-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The sm8450 gen3x1 PHY references the pciephy_v4_regs_layout while the
PHY itself uses v5 regs. While there are only minor differences between
v4 and v5 regs and none of them concerns registers mentions in
regs_layout, switch the PHY to use pciephy_v5_regs_layout to remove
possible confusion.
Fixes: bbe207a1ab ("phy: qcom-qmp-pcie: rename regs layout arrays")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113212138.421583-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Remove QMP PHY type-specific headers inclusion from the common header
and move them to the specific PHY drivers to cleanup the namespaces used
by different drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20221110192248.873973-14-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
