cr_base is base address of PHY control register. The base of WiFi 6 and 7
chips are 0x1_0000 and 0x2_0000 respectively, so define them accordingly.
For example, if PHY address is 0x1330, absolute address is 0x1_1330 for
WiFi 6 chips, and 0x2_1330 for WiFi 7 chips.
Meanwhile, there are two copies of PHY hardware named PHY0 and PHY1. The
offset between them is 0x2_0000, so the base address of PHY0 and PHY1 are
0x2_0000 and 0x4_0000 respectively.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230822125822.23817-6-pkshih@realtek.com
RSSI statistics are grouped by CCK, OFDM or non-legacy rate. These
statistics will be collected in training state for both (main/aux)
antenna. There is a time period (ANTDIV_DELAY) for rate adaptive
settle down before start collect statistics when switch antenna.
Antenna diversity checks packet count from training state for each
group and use the most one as the final RSSI for comparison, and
then choose the better one as target antenna.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230418012820.5139-7-pkshih@realtek.com
Need to configure EDCCA threshold to default value before scan, and recall
original value after scan to prevent probe request can't be sent out.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230322060238.43922-1-pkshih@realtek.com
Since the range of channel table is identical among ICs. Make channel
encode/decode function common and not IC dependent. So all ICs with
matching firmware that needs this kind of coding can use it directly.
This patch doesn't change logic at all.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230220070202.29868-4-pkshih@realtek.com
There are some registers for transmit waveform control, two of them used
in this change are for BANDEDGE and TX_SHAPE control. BANDEDGE controls
whether to apply band edge filter to transmit waveform. TX_SHAPE controls
whether to apply triangular mask to transmit waveform. It is found for
some chip, these two should be turned off during OFDMA UL traffic for
better performance.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221117063001.42967-3-pkshih@realtek.com
For WoWLAN mode, we only collect and send RF parameters to Firmware
without writing RF registers. So we add one function to practice it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221027052707.14605-2-pkshih@realtek.com
The C2H class 2 function 3 is to report retry count of low rate, but driver
doesn't implement yet, so add a dummy case to avoid message:
rtw89_8852be 0000:03:00.0: c2h class 2 not support
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221014060237.29050-4-pkshih@realtek.com
set_channel is main function to configure channel and bandwidth for all
layers, namely MAC, BB and RF. Additionally, MAC layer enables CCK rate
checking to avoid wrong rate from driver. BB layer configures SCO
(Sample Clock Offset) for CCK, TX gain error/offset, and reset baseband
hardware circuit after all configurations done.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-7-pkshih@realtek.com
The gain tables use different domain index, so we need to convert the index
from subband of chandef. Since these conversion functions can share with
8852b, make generic functions for further use.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221005083212.45683-6-pkshih@realtek.com
Previously, we thought control registers or setting things for TX power
series may change according to chip. So, setting functions are implemented
chip by chip. However, until now, the functions keep the same among chips,
at least 8852A, 8852C, and 8852B. There is a sufficient number of chips to
share generic setting functions. So, we now remake them including TX power
by rate, TX power offset, TX power limit, and TX power limit RU as generic
ones in phy.c.
Besides, there are some code refinements in the generic ones, but almost
all of the logic doesn't change.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220928084336.34981-5-pkshih@realtek.com
The calibration value of XTAL offset may be too large in some wifi
modules, that the CFO tracking mechanism under the existing tracking
boundary can not adjust the CFO to the tolerable range. So we enlarge it.
Signed-off-by: Cheng-Chieh Hsieh <cj.hsieh@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220824061425.13764-1-pkshih@realtek.com
For future support on multiple channels, it would be disturbing if we
still allow scattered leaf functions of TX power to query and manage
channel related control by themselves.
So, query rtw89_chan only on top functions. Then, pass it via functions
to make sure that the values coming from the same struct rtw89_chan.
Besides, fix rtw8852a_set_txpwr_offset() from rtw8852a_set_txpwr_ctrl()
to rtw8852a_set_txpwr(). TX power offset should consider current band,
so move it to chip_ops::set_txpwr() which will be called every time that
channel is set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-6-pkshih@realtek.com
Introduce struct rtw89_chan ahead to encapsulate stuffs from struct
rtw89_channel_params. These stuffs have a clone in HAL and are used
throughout driver. After multiple channels support, it's expected that
each channel instance has a configuration of them. So, we refine them
with struct rtw89_chan by precise type first, and will re-arrange HAL
by struct rtw89_chan in the following as well.
(No logic has changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809104952.61355-3-pkshih@realtek.com
Add an new state, RTW89_PHY_DCFO_STATE_HOLD, to keep CFO acceleration
after CFO_PERIOD_CNT if the traffic is UL-OFDMA, which is calculated
based on RX trigger frame counter.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-4-pkshih@realtek.com
When peer's NSS, rate or bandwidth is changed, we update RA(rate adaptive)
mask to ensure transmitting packets properly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220516005215.5878-2-pkshih@realtek.com
BB does many settings during setting channel. First is to configure CCK
for 2G channels, and then basic channel and bandwidth settings with a
encoded channel index that will report to driver when we receive packets.
Configure spur elimination to avoid spur of CSI and NBI tones in certain
frequencies. Also, it initializes BT grant to arrange path sharing with
BT according to band. Finally, reset TSSI and BB hardware to ensure it
stays in initial state.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-12-pkshih@realtek.com
TSSI is used to manage TX power with thermal value as a factor. This patch
is to configure bandedge to TX proper waveform.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-5-pkshih@realtek.com
TX power track tables are used to do TX power compensation according to
thermal value. In order to work in existing and new chip, add new 6G
entries, and change type from u8 to s8.
Internal version table is HALRF_027_00_031.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220414062027.62638-4-pkshih@realtek.com
The format of RF parameter is changed; it doesn't encode delay parameters
into table, but the delay coding becomes regular pair of register address
and value.
To help firmware to recover RF register settings, we need to download
these parameters to firmware. For v1 format, only download partial
parameters (ignore them with addr < 0x100).
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-6-pkshih@realtek.com
Using encoded address which BIT(16) is used to discriminate which region is
going to access. Illustrate the calling flow as below
rtw89_phy_write_rf_v1() -+-> rtw89_phy_write_rf() // old interface
+-> rtw89_phy_write_rf_a() // new interface
Signed-off-by: Chung-Hsuan Hung <hsuan8331@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220317055543.40514-5-pkshih@realtek.com
Set the boundaries of x'tal value to avoid extremely adjusted results,
causing severely unexpected CFO.
Signed-off-by: Yi-Tang Chiu <chiuyitang@realtek.com>
Signed-off-by: Yuan-Han Zhang <yuanhan1020@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220218034537.9338-1-pkshih@realtek.com
Since these macro in rfk helpers are common now, a common naming
should be better. So, apply RTW89_ as prefix to them, and modify
the use correspondly. No logic is changed at all.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-3-pkshih@realtek.com
These rfk helpers are also useful for the chip which is under planning.
So, move them to common code to avoid duplicate stuff in the future.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220211075953.40421-2-pkshih@realtek.com
DIG, which is short for dynamic initial gain, is used to adjust gain to get
good RX performance. CCK PD feature, a mechanism that adjusts 802.11b CCK
packet detection(PD) power threshold based on environment noisy level in
order to avoid false alarm. Also, refine related variable naming.
Signed-off-by: Johnson Lin <johnson.lin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121075555.12457-1-pkshih@realtek.com
We are planning to support more chipsets, e.g. 8852C. Before that, we
consider architecutre to handle multiple kinds of chipsets. Obviosuly,
based on original design, rtw89_core module will have large size even
if there is only one chipset under running. It is because all chipset
related things are put in rtw89_core now. To reduce such overhead, we
extract modules of rtw89 and adjust dependencies between modules.
The following assumes that 8852AE, 8852AU, and 8852CE are all supported,
we describe the difference before and after extraction.
[Before extraction]
-------------
|------------------------------------ | rtw89_usb |
V -------------
--------------------------------------- -------------
| rtw89_core (including 8852A, 8852C) | <--- | rtw89_pci |
--------------------------------------- -------------
The data of 8852A and 8852C are built in rtw89_core.
And rtw89_pci is the entry of 8852AE and 8852CE.
And rtw89_usb is the entry of 8852AU.
[After extraction]
------------- ----------------
|----------- | rtw89_usb | <-------- | rtw89_8852au |
| ------------- ----------------
V --------------- |
-------------- | | <---------------
| rtw89_core | <--- | rtw89_8852a |
-------------- | | <---------------
^ ^ --------------- |
| | ------------- ----------------
| | | | <-------- | rtw89_8852ae |
| |----------- | rtw89_pci | ----------------
| | | <-----------------
| ------------- |
| --------------- ----------------
|--------------- | rtw89_8852c | <------ | rtw89_8852ce |
--------------- ----------------
The data of 8852A/8852C is extracted to rtw89_8852a/rtw89_8852c.
And rtw89_pci/rtw89_usb handles only common flow of pci/usb bus.
Finally, 8852AE, 8852AU, and 8852CE have individual entry modules,
i.e. rtw89_8852ae, rtw89_8852au, and rtw89_8852ce correspondingly.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221025828.25092-1-pkshih@realtek.com
We used to fill in rx skbs' frequency field by mac80211's current
channel value. In some cases, mac80211 switches channel before all
rx packets have been processed. This results in incorrect bss info.
We fix this by filling in frequency field with channel index obtained
from hardware, then fix potential cck missing issue by skb's original
hw rate. After all fix is done, convert hw rate back to the supported
band rate index.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211111023706.14154-3-pkshih@realtek.com
This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.
The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.
Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:
Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>
Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com
