When the 'Disabled Subchannel Bitmap' within the EHT Operation
element is changed, mac80211 parse and pass it to the driver.
The driver is then updated with this puncturing bitmap to
optimize bandwidth usage and prevent interference from
degrading performance across the entire channel.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250715035259.45061-4-pkshih@realtek.com
For some implementation acting as GO under MCC(GO+STA), the GO's TBTT
might change after STA roams to another AP. This could result the new GO
beacon TX at the STA timeslot of GC+STA, causing GC beacon loss.
Therefore, if the GC detects beacon loss, it will pause MCC and remain
on the GO side for 100 TU to detect the new TBTT beacon.
Additionally, some implementation acting as GO under MCC might TX beacon
too close to the NoA period. The GC calculates timeslot pattern the TOB
(time offset behind) or TOA(time offset ahead) less than the minimum
RX beacon time, which leads to beacon loss. Therefore, disable the
beacon filter in this case. Then, if the GO's TBTT changed, the pattern
TOB/TOA greater than the minimum RX beacon time, the beacon filter should
be retriggered during MCC update.
Moreover, if the beacon filter is disabled initially but the GO timeslot
change, causing QoS null data detection fail, also pause MCC to detect new
TBTT beacon.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250710042423.73617-7-pkshih@realtek.com
MCC stop might triggered by scan, and need to force to stay at GO role
to keep TX beacon. Also, AX chips need to TX more 3 beacons to ensure
GC can receive once NoA beacon before scan when GC in courtesy mode.
BE chips no needs to TX 3 more beacon because it can TX beacon every
200TU during scan, even GC in courtesy mode can receive beacon every
600TU.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250710042423.73617-5-pkshih@realtek.com
MCC require time to switch channel when changing timeslot. If GC TX
nulldata 0 while GO is switching channel, GO can't receive it. Therefore,
enlarge the GO NoA duration to cover the channel switching time.
However, the enlarged NoA duration might cause GC's timeslot less than
minimum of RX beacon time. Therefore, adjust strict and anchor pattern
condition to avoid it.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250710042423.73617-4-pkshih@realtek.com
The PD lower bound set after one interface is connected, If second
interface needs to connect, packets might not be detected because the
PD lower bound is too high. Therefore, a DIG suspend/resume flow is
added to decrease the PD lower bound during scanning or connection,
and the original PD level is resumed afterward.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250710042423.73617-3-pkshih@realtek.com
Packet detection(PD) lower bound is the threshold for sensing packet,
and it is dynamically calculated based on RSSI. In MCC, the two
interfaces have different RSSI values, so it is necessary to set
different values to ensure packets can be received. Therefore, add
H2C command to let firmware to switch PD lower bound when MCC mode.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250710042423.73617-2-pkshih@realtek.com
Add Wi-Fi 7 MLO related multi-role (MR) chanctx descriptors and query
function. They are designed for other components, e.g. coex, which are
interested in the following info.
* whether a MLD exists and how many active link
* the number of AP mode and station mode respectively
* how many chanctx and the number of 2/5/6 GHz respectively
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250611035523.36432-2-pkshih@realtek.com
If scan happen during start_ap, the register which control TX might be
turned off during scan. Additionally, if set_channel occurs during scan
will backup this register and set to firmware after set_channel done.
When scan complete, firmware will also set TX by this register, causing
TX to be disabled and beacon can't be TX. Therefore, in assign/unassign_vif
call scan abort before set_channel to avoid scan racing with set_channel.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-13-pkshih@realtek.com
When the beacon offset is less than minimum of auxiliary tob
(aux->duration - aux->limit.max_toa), the upper bound of the reference
toa might be negative and lower than the lower bound, which causes the
auxiliary result to exceed the NoA limit. Therefore, in this case, the
anchor pattern is used for calculation.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-11-pkshih@realtek.com
Clear NoA setting before MCC starts. Otherwise, nulldata will be
blocked to TX because firmware use the normal flow NoA to calculate
timing.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-10-pkshih@realtek.com
Stop TX during the MCC configuration period to prevent packet leakage.
The stop time is defined as 'start_tsf - tsf', which means the duration
from when MCC configuration begins until MCC starts.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-6-pkshih@realtek.com
MCC needs to wait at most 300ms to start. Additionally, if
scanning happens before MCC starts, it will miss some beacons,
which might cause beacon loss. Therefore, we reset beacon
filter when MCC start to let hardware reset beacon loss counter.
Additionally, GO is forbid to enter courtesy mode might cause
STA beacon loss. Therefore, disable beacon filter when GO+STA.
However, In WiFi 7 chip, even when GC+STA enable courtesy mode, the
beacon might loss because switching to courtesy timeslot will disable
TX/RX. If the TOB(time offset behind) or TOA(time offset ahead) is
too close to the edge of timeslot, the beacon might not be received.
Therefore, disable beacon filter when GC+STA in WiFi 7 chip.
Because disabling the beacon filter might prevent disconnection
when the AP power-off without sending a deauth. Therefore, driver
TX QOS nulldata periodically to detect the AP status, and the
connection is terminated if no ACK is received for 6 seconds.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250610130034.14692-5-pkshih@realtek.com
To support channel switch on STA mode, declare IEEE80211_HW_CHANCTX_STA_CSA
and implement ieee80211_ops::switch_vif_chanctx. Handling of CSA procedure
still relies on mac80211 SW flow, since FW doesn't support chanctx offload.
To support channel switch on AP mode, declare WIPHY_FLAG_HAS_CHANNEL_SWITCH
and implement ieee80211_ops::channel_switch_beacon additionally.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250605114207.12381-4-pkshih@realtek.com
Previously, default chandef is configured if no chanctx is active, i.e. no
chanctx is assigned to some vif. For normal cases, it's fine. However, for
impending CSA support, need to consider that one chanctx may be added, or
called registered, ahead without being assigned immediately. Then, it will
keep inactive, and might be covered by the default one when re-calculating
chanctxs happens in certain sequences. So now, don't re-config the default
chandef unless no chanctx is registered.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250605114207.12381-3-pkshih@realtek.com
Originally, the logic for setting bits was wrapped inside the configuring
function. However, raw clearing bits, clear_bit, was called directly. To be
more paired and more understandable. Concentrate the logic of them into the
same function.
(don't change logic at all)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250605114207.12381-2-pkshih@realtek.com
MCC will track the changes of beacon offset, and trigger a recalculation
when the difference is larger than the tolerance. It means that a better
pattern is expected after recalculating. However, in the cases which get
a worse beacon offset, there is no chance to improve the pattern even if
recalculating. So, bypass them.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-7-pkshih@realtek.com
Originally, MCC just took periodic NoA into account. When the connected GO
announces non-periodic NoA and GC side is during MCC, sometimes GC cannot
receive beacons well if the MCC scheduling conflicts with the non-periodic
NoA planning. After the loss exceeds the tolerable amount, beacon filter
will report connection loss. However, in this case, the loss is acceptable.
So now, MCC will calculate the range of non-periodic NoA. And then, don't
care beacon loss during the range.
Besides, rtw89_mcc_fill_role_limit() only makes sense for GC. Remove the
redundant check of GO.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-6-pkshih@realtek.com
In the cases that two MCC roles' TBTTs are too close or too far, original
MCC pattern calculation logic will lead to a result that both roles might
not cover its TBTT with sufficient time. Introduce a new calculation logic
called anchor pattern for these corner cases. It allows to choose one role
as anchor to put its TBTT in the middle of its duration directly. For now,
a P2P role has a higher priority to be chosen as an anchor. Then, if able,
another role might need to depend on courtesy mechanism to take time from
anchor.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-5-pkshih@realtek.com
In one enablement of courtesy mechanism, there is one provider and
one receiver. And, receiver can use the provider's time in a given
period. But, to make P2P NoA protocol work as expected as possible,
GO should be present at the time it doesn't announce absent, and GC
should not use the time when GO announces absent. So, don't enable
courtesy mechanism if provider is GO or receiver is GC.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-4-pkshih@realtek.com
When MCC is about to stop, there may be some chanctx changes which are
queued for work but have not yet been run. To avoid these changes from
being processed in a wrong state (e.g. next new MCC instance), cancel
the queued work and drop queued changes.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-3-pkshih@realtek.com
When stopping MCC, FW can stop at a given MCC role following H2C command.
When pausing chanctx during MCC, in general, the caller expects to process
things with its chanctx. So, pass the caller as target and let FW stop MCC
at it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250511035217.10410-2-pkshih@realtek.com
Wi-Fi 7 chips have dual HW bands. After impending MLO support, they
can work with HW-[0] / HW-[1] / HW-[0,1] according to active links.
So, during setting channel, also re-calculate the MLO DBCC mode flag.
Then, leaf chip functions of setting channel can configure with HWs
based on current case.
Besides, tweak the initial and idle MLO DBCC mode of Wi-Fi 7 chips to
MLO_1_PLUS_1_1RF to work with dual HW bands. And, after disconnecting,
due to no active links, MLO DBCC mode will re-calculate to idle case,
i.e. MLO_1_PLUS_1_1RF.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250505072440.45113-5-pkshih@realtek.com
A link bound to HW band 0 was previously always assumed to exist, because
it's true on non-MLD connection, and MLO connection is not supported yet.
Now, start to consider MLO cases and prepare to enable MLO support in the
following. Add skeleton of designated link. For single-link cases, helper
returns the one. For multi-link cases, priorities can be scheduled. Then,
drop assumption of link bound to HW band 0.
One exception is that MCC doesn't work with MLD yet, so it still expects
link on HW band 0 somewhere.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250428112456.13165-11-pkshih@realtek.com
Originally, a macro, RTW89_ROC_BY_LINK_INDEX, is used to decide the link
which deals with the ROC process. Before enabling MLO support, it's fine
to hard-code RTW89_ROC_BY_LINK_INDEX as 0 since the link instance-0 (on
HW-0) is always active. But, for the impending enablement of MLO support,
tweak the leaf functions to dynamically handle ROC link instance index.
Besides, in the follow-up, ROC caller will get a designated link and will
then drop RTW89_ROC_BY_LINK_INDEX.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250428112456.13165-10-pkshih@realtek.com
A MCC (multi-channel concurrency) schedule is like the following.
|< mcc interval >|
|< duration ref >|< duration aux >|
|< tob ref >|< toa ref >|< tob aux >|< toa aux >|
V V
tbtt ref tbtt aux
|< beacon offset >|
Original logic might unexpectedly calculate toa (time offset ahead) of
auxiliary role to be negative even when there is no role timing limit.
If toa-aux is negative, TBTT-aux would in logic fall into duration-ref.
Then, if auxiliary role is GO unfortunately, it cannot guarantee that
beacons will TX well. So now, when deciding the lower bound of toa-ref,
take toa-aux into account. Make toa-aux at least be zero in normal cases.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-13-pkshih@realtek.com
Since tob (time offset behind) could be negative, change the type of tob in
microsecond to s32. And, refine accumulation with while-loop by calculation
with roundup_u64(). Besides, as long as one of the MCC roles is GO, use the
short MCC start time.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-12-pkshih@realtek.com
MCC has a courtesy mechanism which allows one role to use another's
duration in a given cycle. Originally, this courtesy mechanism only
supports in one direction. However, in some field cases, both of MCC
roles may simultaneously have timing configurations that are not good
enough. So, support courtesy mechanism in both directions.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-11-pkshih@realtek.com
MCC has a courtesy mechanism which allows one role to use another's
duration in a given cycle. Courtesy mechanism will be enabled when
one role has a not perfect duration. Otherwise, not. When MCC updates,
duration of each role will be re-calculated. And then, the new courtesy
config might be different from the old one. However, to change courtesy
config, the entire MCC plan requires to be renewed when MCC updates.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-10-pkshih@realtek.com
MCC will limit the time a role can use in a schedule according to the
periodic NoA. Original logic didn't consider the case where NoA start
time has passed. It might lead to inaccurate result. So, tweak it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-9-pkshih@realtek.com
There are two roles during MCC and the offset between their TBTT is called
beacon offset. Originally, when MCC runs GO+STA mode, it used fixed beacon
offset to simplify some logic because GO role can master its TSF. However,
if MCC is stopped and restarted before a same GO is down, its TSF might be
discontinuous. Then, there might be undefined behavior happens in GC sides.
So, to let a same GO have a continuous TSF, MCC no longer changes its TSF
to meet a fixed beacon offset. Instead, GO+STA mode also calculates beacon
offset dynamically as what GC+STA mode did.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250422014620.18421-8-pkshih@realtek.com
TAS state switching mechanism now incorporates the TX ratio as a
decision parameter. The average power calculation has been improved
by using a higher resolution conversion from dBm to linear. During
scan or MCC operations, TAS state is forced to static SAR and
suspend the average power calculation. Additionally, TAS window
size depends on the regulatory domain and band to ensure compliance.
TAS is enabled when permitted by the regulatory domain and is
currently supported on the 8852CE.
For debugging, add a flag to disable_dm that can stop TAS mechanism.
Co-developed-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-3-pkshih@realtek.com
With spatch script, already remove most driver mutex and generate
lockdep_assert_wiphy(), and some are needed to refine manually further to
be expected:
- lockdep_assert_wiphy() always be the first statement in function
- return directly rather than unnecessary goto
- change assert from mutex to wiphy lock, which script can't convert
automatically.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250122060310.31976-9-pkshih@realtek.com
For certain works protected by driver mutex, use wiphy_work() directly
to have wiphy lock held naturally. Then every this kind of works is
protected by both wiphy lock and driver mutex.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250122060310.31976-3-pkshih@realtek.com
For each MCC role, time limits, including max_tob_us, max_toa_us, and
mac_dur_us, are calculated if there are NoA attributes. The relation
between these time limits is "max_dur_us = max_tob_us + max_toa_us".
Then, the unit is converted from us to TU. However, originally, each
time limit was divided by 1024 independently. It missed to consider
the cases that max_tob_us or max_toa_us is not divisible by 1024. It
causes the result breaks "max_dur (TU) = max_tob (TU) + max_toa (TU)".
Finally, when MCC calculates pattern parameters based on these kinds
of time limits, it might not perform well.
Fixes: b09df09b55 ("wifi: rtw89: mcc: initialize start flow")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250103074412.124066-1-pkshih@realtek.com
During rtw89_entity_recalc_mgnt_roles(), there is a normalizing process
which will re-order the list if an entry with target pattern is found.
And once one is found, should have aborted the list_for_each_entry. But,
`break` just aborted the inner for-loop. The outer list_for_each_entry
still continues. Normally, only the first entry will match the target
pattern, and the re-ordering will change nothing, so there won't be
soft lockup. However, in some special cases, soft lockup would happen.
Fix it by `goto fill` to break from the list_for_each_entry.
The following is a sample of kernel log for this problem.
watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [wpa_supplicant:2055]
[...]
RIP: 0010:rtw89_entity_recalc ([...] chan.c:392 chan.c:479) rtw89_core
[...]
Fixes: 68ec751b28 ("wifi: rtw89: chan: manage active interfaces")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-3-pkshih@realtek.com
When starting/proceeding MCC, it will abort an ongoing hw scan process.
In the proceeding cases, it unexpectedly tries to abort a non-exist hw
scan process. Then, a trace shown at the bottom will happen. This problem
is caused by a previous commit which changed some call sequence inside
rtw89_hw_scan_complete() to fix some coex problems. These changes lead
to our scanning flag was not cleared when proceeding MCC. To keep the
fixes on coex, and resolve the problem here, re-consider the related
call sequence.
The known sequence requirements are listed below.
* the old sequence:
A. notify coex
B. clear scanning flag
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
(the problem: A needs to be after C-1)
* the current sequence:
C. proceed chanctx
C-1. set channel
C-2. proceed MCC
A. notify coex
B. clear scanning flag
(the problem: C-2 needs to be after B)
So, now let hw scan caller pass a callback to proceed chanctx if needed.
Then, the new sequence will be like the below.
C-1. set channel
A. notify coex
B. clear scanning flag
C-2. proceed MCC
The following is the kernel log for the problem in current sequence.
rtw89_8852be 0000:04:00.0: rtw89_hw_scan_offload failed ret -110
------------[ cut here ]------------
[...]
CPU: 2 PID: 3991 Comm: kworker/u16:0 Tainted: G OE 6.6.17 #3
Hardware name: LENOVO 2356AD1/2356AD1, BIOS G7ETB3WW (2.73 ) 11/28/2018
Workqueue: events_unbound wiphy_work_cancel [cfg80211]
RIP: 0010:ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
Code: 9c 24 d0 11 00 00 49 39 dd 0f 85 46 ff ff ff 4c 89 e7 e8 09 2d
RSP: 0018:ffffb27783643d48 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff8a2280964bc0 RSI: 0000000000000000 RDI: ffff8a23df580900
RBP: ffffb27783643d88 R08: 0000000000000001 R09: 0000000000000400
R10: 0000000000000000 R11: 0000000000008268 R12: ffff8a23df580900
R13: ffff8a23df581b00 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8a258e680000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f26a0654000 CR3: 000000002ea2e002 CR4: 00000000001706e0
Call Trace:
<TASK>
? show_regs+0x68/0x70
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? __warn+0x8f/0x150
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
? report_bug+0x1f5/0x200
? handle_bug+0x46/0x80
? exc_invalid_op+0x19/0x70
? asm_exc_invalid_op+0x1b/0x20
? ieee80211_sched_scan_stopped+0xaea/0xd80 [mac80211]
ieee80211_scan_work+0x14a/0x650 [mac80211]
? __queue_work+0x10f/0x410
wiphy_work_cancel+0x2fb/0x310 [cfg80211]
process_scheduled_works+0x9d/0x390
? __pfx_worker_thread+0x10/0x10
worker_thread+0x15b/0x2d0
? __pfx_worker_thread+0x10/0x10
kthread+0x108/0x140
? __pfx_kthread+0x10/0x10
ret_from_fork+0x3c/0x60
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
---[ end trace 0000000000000000 ]---
Fixes: f16c40acd3 ("wifi: rtw89: Fix TX fail with A2DP after scanning")
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241231004811.8646-2-pkshih@realtek.com
Setting of channel and TX power depend on channel contexts, but original
code cannot handle combination of MCC (multi-channel concurrency) and MLO
well. So according to active interfaces, we generate a table for current
channel contexts. And then based on entity mode, we get the corresponding
channel context to apply during channel or TX power setting. When MLO is
supported, there will be dual-PHY and we will apply the channel context of
the 2nd link to the 2nd PHY.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241022083106.149252-5-pkshih@realtek.com
To set channel well for combination of MCC (multi-channel concurrency) and
impending MLO support, we need a method to manage relation between active
interfaces and channel contexts. If an interface owns at least one active
link, we call it an active interface. We add a list to manage active ones.
Basically, the list follows the active order except for the below case. To
be compatible with legacy behavior, the first interface that owns the first
channel context will put at the first entry in the list when recalculating.
Besides, MCC can also select and fill roles based on the above active list.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20241022083106.149252-4-pkshih@realtek.com
The drv_priv hooked to mac80211 become as below.
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_vif | <---> | rtw89_vif | -------> | rtw89_vif_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_vif_link |
+----------------+
(drv_priv) (instance-0)
+---------------+ +-----------+ +----------------+
| ieee80211_sta | <---> | rtw89_sta | -------> | rtw89_sta_link |
+---------------+ +-----------+ | +----------------+
|
| (instance-1)
| +----------------+
+---> | rtw89_sta_link |
+----------------+
The relation bewteen mac80211 link_id and our link instance is like below.
|\
(link_id) | \
0 -------- | |
1 -------- | | ------ instance-0 (link_id: X) -> work on HW band 0
2 -------- | |
... | | ------ instance-1 (link_id: Y) -> work on HW band 1
14 -------- | |
| /
|/
N.B. For cases of non-MLD connection, we set our link instance-0
active with link_id 0. So, our code flow can be compatible between
non-MLD connection and MLD connection.
Based on above, we tweak entire driver architecture first. But, we don't
dynamically enable multiple links here. That will be handled separately.
Most of the things changed here are changing flows to iterate all active
links and read bss_conf/link_sta data according to target link. And, for
cases of scan, ROC, WOW, we use instance-0 to deal with the request.
There are some things listed below, which work for now but need to extend
before multiple active links.
1. tx path
select suitable link instance among multiple active links
2. rx path
determine rx link by PPDU instead of always link instance-0
3. CAM
apply MLD pairwise key to any active links dynamically
Besides, PS code cannot easily work along with tweaking architecture. With
supporting MLO flag (currently false), we disable PS first and will fix it
by another commit in the following.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-8-pkshih@realtek.com
Tweak code to not always access vif->bss_conf directly. Instead,
according to link_id, read target bss_conf from vif->link_conf[].
For now, rtwvif_link->link_id keeps 0. When driver starts to
support MLO, the link_id will be assigned.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-4-pkshih@realtek.com
This is an intermediate version that is separated from subsequent major
MLO changes, so some functions' namings are not really determined here.
e.g. struct rtw89_sta_link *sta_to_rtwsta_safe(struct ieee80211_sta *sta)
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-3-pkshih@realtek.com
This is an intermediate version that is separated from subsequent major
MLO changes, so some functions' namings are not really determined here.
e.g. struct rtw89_vif_link *vif_to_rtwvif_safe(struct ieee80211_vif *vif)
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240916053158.47350-2-pkshih@realtek.com
The target enum has been renamed to rtw89_"chanctx"_idx. So for
readability, rename roc_entity_idx to roc_"chanctx"_idx to align.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240819091724.33730-8-pkshih@realtek.com
Originally, we planed to fill MAC_0/1 indicators with chanctx and
use sub_entity_xxx for these things. However, there are some reasons
listed below which make us give up this plan after we know our Wi-Fi 7
HW design.
1. one link is bound to one HW band during its life time
but, one link might change chanctx dynamically
2. in concurrent mode, assume 1st vif is MLD
1st vif's 2nd link might use the same chanctx as 2nd vif
but, they are not on the same HW band
So, we let sub_entity_xxx stuffs deal with only chanctx now. And, to be
more readable, we rename sub_entity related words to chanctx.
No logic is changed.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-4-pkshih@realtek.com
In general, MCC (multi-channel concurrency) stops when some chanctx is
unassigned. Originally, we let FW to stop at a fixed role. However, it
might be the one to be unassigned.
So, iterate MCC roles and select one which is still holding chanctx.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-3-pkshih@realtek.com
Originally during unassign-chanctx, MCC (multi-channel concurrency) is
re-planed before set-channel if need. But, we might calculate MCC stuffs
based on old channel info. And, the following set-channel might be racing
with FW MCC state mechanism. So, we refine this flow. Now, if MCC re-plan
is needed here, it will be done after set-channel.
Besides, to be more rigorous, we now ensure entity isn't paused before we
deal with MCC things here.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240727080650.12195-2-pkshih@realtek.com
Driver will notify FW the target index of RFK table to use at some
moments. When MCC (multi-channel concurrent), the correctness of the
notification is especially important.
We now unify the selection logic of RFK table as below among chips.
1. check each table if it matches target channel
2. check all tables if any is idle by iterating active channels
3. replace the first table if all are busy unexpectedly
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240702124452.18747-2-pkshih@realtek.com
On Wi-Fi 7 chips, concurrent stuffs are supported by FW MRC series
(multi-role concurrent) functions. And, driver has implemented the
corresponding SW handling in patches in front of this one. Now, we
extend SW MCC (multi-channel concurrent) flow to work on Wi-Fi 7
chips.
In SW point of view, things look as below.
| SW | | FW func |
| | | H2C/C2H |
--------------------------------------------
| | ax |
| | /----| FW MCC func |
| MCC | -- chip --+ |
| | \----| FW MRC func |
| | be |
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240213073514.23796-5-pkshih@realtek.com
