This is needed for AP mode. Otherwise client sees the network, but
can't connect to it.
REG_FWHW_TXQ_CTRL+1 is set to WLAN_TXQ_RPT_EN (0x1F) in common mac
init function (__rtw8723x_mac_init), but the value was overwritten
from mac table later.
Tables with register values for phy parameters initialization are
copied from vendor driver usually. When table will be regenerated,
manual modifications to it may be lost. To avoid regressions in this
case new callback mac_postinit is introduced, that is called after
parameters from table are set.
Tested on rtl8723cs, that reuses rtw8703b driver.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250711084740.3396766-1-andrej.skvortzov@gmail.com
The RTW_WCPU_11AC and RTW_WCPU_11N enums are used to identify two
types of microcontrollers used in Realtek chips, but these names are
misleading. The "11AC" type was also used in 11n devices (e.g.
RTL8733BU, not supported by rtw88), and the "11N" type was also used
in 11ac devices (RTL8821AU, RTL8812AU).
Rename RTW_WCPU_11AC to RTW_WCPU_3081 and RTW_WCPU_11N to RTW_WCPU_8051.
(8051 is well known. It's less clear what 3081 is, but the out of tree
drivers use this name.)
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bfb1099c-db52-4b25-b111-17ab712e9404@gmail.com
Tell the chip the maximum AMPDU size supported by the AP. This greatly
improves the TX speed of RTL8814AU in the 2.4 GHz band. Before: ~90
Mbps. After: ~300 Mbps.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/4edc2a63-81b3-431c-9a37-5a7d899a6cc2@gmail.com
Register a struct led_classdev with the kernel's LED subsystem and
create a throughput-based trigger for it. Then mac80211 makes the LED
blink.
Tested with Tenda U12 (RTL8812AU), Tenda U9 (RTL8811CU), TP-Link Archer
T2U Nano (RTL8811AU), TP-Link Archer T3U Plus (RTL8812BU), Edimax
EW-7611UCB (RTL8821AU), LM842 (RTL8822CU).
Also tested with devices which don't have LEDs: the laptop's internal
RTL8822CE and a no-name RTL8723DU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/6c43451f-ab2f-4e76-ac6e-ff5a18dd981d@gmail.com
Some RTL8812AU devices fail to probe:
[ 12.478774] rtw_8812au 1-1.3:1.0: failed to dump efuse logical map
[ 12.487712] rtw_8812au 1-1.3:1.0: failed to setup chip efuse info
[ 12.487742] rtw_8812au 1-1.3:1.0: failed to setup chip information
[ 12.491077] rtw_8812au: probe of 1-1.3:1.0 failed with error -22
It turns out these chips don't need to "protect" any bytes at the end of
the efuse.
The original value of 96 was copied from rtw8821c.c.
No one reported any failures with RTL8821AU yet, but the vendor driver
uses the same efuse reading code for both chips.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/1a477adb-60c3-463c-b158-3f86c94cb821@gmail.com
RF front end type 2 exists in the wild and can be treated like types
0 and 1.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/2917c7fc-6d88-4007-b6a6-9130bd1991e5@gmail.com
