In order to set channel info to hal during HW scan, we add the update
channel flow to support setting by parameters to meet the HW scan
requriement.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-4-pkshih@realtek.com
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
Some WSC IEs require size larger than we current supports. Extend size
to fit those demands. Separate the registered scan IE length by IC so
settings can be independent.
Since old firmware uses fewer page number, define a firmware feature to
be compatible with various firmware version.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-2-pkshih@realtek.com
The function alloc_workqueue() in rtw_core_init() can fail, but
there is no check of its return value. To fix this bug, its return value
should be checked with new error handling code.
Fixes: fe101716c7 ("rtw88: replace tx tasklet with work queue")
Reported-by: Hacash Robot <hacashRobot@santino.com>
Signed-off-by: William Dean <williamsukatube@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220723063756.2956189-1-williamsukatube@163.com
Start making some SMPS related code MLD-aware. This isn't
really done yet, but again cuts down our 'deflink' reliance.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
-----BEGIN PGP SIGNATURE-----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=E0Dx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless-next patches for v5.20
Here's a first set of patches for v5.20. This is just a
queue flush, before we get things back from net-next that
are causing conflicts, and then can start merging a lot
of MLO (multi-link operation, part of 802.11be) code.
Lots of cleanups all over.
The only notable change is perhaps wilc1000 being the
first driver to disable WEP (while enabling WPA3).
* tag 'wireless-next-2022-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (29 commits)
wifi: mac80211_hwsim: Directly use ida_alloc()/free()
wifi: mac80211: refactor some key code
wifi: mac80211: remove cipher scheme support
wifi: nl80211: fix typo in comment
wifi: virt_wifi: fix typo in comment
rtw89: add new state to CFO state machine for UL-OFDMA
rtw89: 8852c: add trigger frame counter
ieee80211: add trigger frame definition
wifi: wfx: Remove redundant NULL check before release_firmware() call
wifi: rtw89: support MULTI_BSSID and correct BSSID mask of H2C
wifi: ray_cs: Drop useless status variable in parse_addr()
wifi: ray_cs: Utilize strnlen() in parse_addr()
wifi: rtw88: use %*ph to print small buffer
wifi: wilc1000: add IGTK support
wifi: wilc1000: add WPA3 SAE support
wifi: wilc1000: remove WEP security support
wifi: wilc1000: use correct sequence of RESET for chip Power-UP/Down
wifi: rtlwifi: fix error codes in rtl_debugfs_set_write_h2c()
wifi: rtw88: Fix Sparse warning for rtw8821c_hw_spec
wifi: rtw88: Fix Sparse warning for rtw8723d_hw_spec
...
====================
Link: https://lore.kernel.org/r/20220610142838.330862-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add this check to avoid crash by dereferencing a null pointer. When hwscan
fails due to no memory or dma failure, the scan flag in ieee80211_local is
cleared. So mac80211 determine that it's not hw_scan then calls
sw_scan_complete() with null vif, which is also freed during the fail.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220520081523.45987-1-pkshih@realtek.com
Each chip have best ampdu density value, the correct setting can improve
throughput performance.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-1-pkshih@realtek.com
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
Adding this allows us to get notification when bitrate configuration
of the station changes. Update according parameters to firmware so
the rate control algorithm can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-2-pkshih@realtek.com
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously we only consider single interface's status, idle mode
behavior could be unexpected when multiple interfaces is active.
Change to enter/leave idle mode by mac80211's configuration state.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220318034316.40720-1-pkshih@realtek.com
In order to recognize the gaming controller HID, make a C2H/H2C/Mailbox
handshake to collect all the connected information from BT.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-6-pkshih@realtek.com
If BT PTA counter can not update regularly, it will lead coex mechanism
run into some unexpected state.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-4-pkshih@realtek.com
In some case, wifi chip need to be configed to be TX/RX 1ss mode.
For this mode, wifi components, such as MAC/BB/RF, need to be
specially set, and driver need to send SMPS action frame to inform AP.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-2-pkshih@realtek.com
Some APs like CMW270 only support one phyrate and the function
rtw_update_rate_mask could disable that rate. To fix such problem, we
restore the rate mask if we find that the rate_mask is empty.
Signed-off-by: Chien-Hsun Liao <ben.liao@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208082427.42433-2-pkshih@realtek.com
Upon hw scan completion, idle mode is not re-entered. This might
increase power consumption under no link mode. Fix this by adding the
re-enter flow. We need another work for this since enter_ips waits
for c2h_work to finish, which might lead to deadlock if caller is in
the same work.
Fixes: 10d162b2ed ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-3-pkshih@realtek.com
Register cfg80211_sar_capa with type NL80211_SAR_TYPE_POWER and four
frequency ranges for configurations in unit of 0.25 dBm. And handle
callback set_sar_specs.
Originally, TX power has three main parameters, i.e. power base,
power by rate, and power limit. The formula can be simply considered
as TX power = power base + min(power by rate, power limit). With the
support of SAR which can be treated as another power limit, there is
one more parameter for TX power. And the formula will evolve into
TX power = power base + min(power by rate, power limit, power sar).
Besides, debugfs tx_pwr_tbl is also refined to show SAR information.
The following is an example for the difference.
Before supporting SAR,
-----------------------------------
...
path rate pwr base (byr lmt ) rem
A CCK_1M 66(0x42) 78 -12 ( 12 -12) 0
A CCK_2M 66(0x42) 78 -12 ( 8 -12) 0
...
-----------------------------------
After supporting SAR and making some configurations,
-----------------------------------
...
path rate pwr base (byr lmt sar ) rem
A CCK_1M 62(0x3e) 78 -16 ( 12 -12 -16) 0
A CCK_2M 62(0x3e) 78 -16 ( 8 -12 -16) 0
...
-----------------------------------
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211220093656.65312-1-pkshih@realtek.com
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
These settings enables mac to detect and recover when rx fifo
circuit deadlock occurs. Previous version missed this, so we fix it.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211217012708.8623-1-pkshih@realtek.com
It is useful to fix the bit rate of TX packets. For example, if
someone is measuring the TX power, or debugging with the issues
of the TX throughput on the field.
To set the value of fixed rate, one should input corresponding
desc rate index (ex, 0x0b for DESC_RATE54M to fix at 54 Mbps).
Set a value larger than DESC_RATE_MAX will disable fix rate, so
the rate adaptive mechanism can resume to work.
Example,
To fix rate at MCS 1:
echo 0x0d > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To not to fix rate:
echo 0xff > /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
To know which rate was fixed at:
cat /sys/kernel/debug/ieee80211/phy0/rtw88/fix_rate
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211129020506.6273-1-pkshih@realtek.com
The usage of fw_crash debugfs is to write 1 to it to trigger fw crash
simulation and to read from it to check the state. When zero is read,
it is supposed to mean fw crash/restart process is done. Then, some
test plans can be designed for crash/restart.
e.g.
step 1. trigger fw crash simulation
step 2. poll the state until zero is read
step 3. check connection by ping test
However, in certain connection cases, triggering fw crash simulation
will take a while. If the state is queried too early before restart
begins processing, it may mistakenly think restart process has been
done. If some tests are started at this time, something unexpected
might happen due to the follow-up restart process.
To avoid that, let fw_crash also show non-zero when a simulation
is still triggering.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211001082301.4805-1-pkshih@realtek.com
Add Energy Detected CCA (EDCCA) mechanism to detect energy on the channel.
And EDCCA support adaptivity mode now. From MIC Ordinance Regulating Radio
Equipment article 49.20, ETSI EN-300-328 and EN-301-893, the device should
be able to dynamically pause TX activity when energy detected on the air.
According to ETSI/JP DFS region, driver will set corresponding threshold
and stop TX activity if the detected energy exceeds the threshold. For now,
we support it on 8822b and 8822c first.
By default, EDCCA mechanism is turned on. For ETSI/JP DFS region, it will
turn to adaptivity mode. However, with adaptivity, if environment is too
noisy, TX may often be halted. So, a debugfs for EDCCA is added. It can
show what EDCCA mode is used currently. And EDCCA mechanism can be turned
on/off through the debugfs while debugging.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-4-pkshih@realtek.com
Realtek chips can program a specific country domain on efuse to
indicate what is the expected rtw_regulatory. For chips with a
programmed country domain, we set REGULATORY_STRICT_REG to tell
stack to consider follow-up regulatory_hint() as the superset of
our regulatory rule. Besides, on driver side, only the request via
NL80211_REGDOM_SET_BY_DRIVER, which matches programmed country
domain, will be handled to keep rtw_regulatory unchanged.
For worldwide roaming chips, i.e. ones without a specific programmed
country domain, system of distro can set expected regulatory via
NL80211_REGDOM_SET_BY_USER. With setting from it, rtw_regulatory
will handle the requests only via NL80211_REGDOM_SET_BY_USER to
follow setting from system of distro. REGULATORY_COUNTRY_IE_IGNORE
will then be set to tell stack to ignore country IE for us. The
restrictions mentioned above will remain until 00, i.e. worldwide,
is set via NL80211_REGDOM_SET_BY_USER.
On the other hand, for worldwide roamin chips, if there is no
specific regulatory set via NL80211_REGDOM_SET_BY_USER, requests
from all regulatory notifications will be handled by rtw_regulatory.
And REGULATORY_COUNTRY_IE_IGNORE won't be set.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-3-pkshih@realtek.com
Enabling this improves tx performance for long distance transmission.
We used to enable stbc by the rx stbc cap of the associated station.
But rx cap will be masked out in ieee80211_ht_cap_ie_to_sta_ht_cap
if we do not declare tx stbc.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210713104524.47101-2-pkshih@realtek.com
Fix erroneous code that leads to unreferenced objects. During H2C
operations, some functions returned without freeing the memory that only
the function have access to. Release these objects when they're no longer
needed to avoid potentially memory leaks.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210624023459.10294-1-pkshih@realtek.com
Use device coredump framework instead of print_hex_dump to support
FW crash dump. Pass data to the framework if preparing and dumping
are successful. The framework will take the ownership of the data.
The data will be freed after the framework determines its lifetime
is over. A new coredump will not work if the previous one still
exists.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210528032901.12927-2-pkshih@realtek.com
It is found that driver scan could be affected by dynamic mechanism
of firmware, so we notify firmware to stop it in the scan period.
Another, firmware will detect the background noise and report to
driver for further use.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-3-pkshih@realtek.com
add api to check if a certain feature is supported.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-2-pkshih@realtek.com
Adding this supports beacon filter and CQM.
Let firmware perform connection quality monitor and beacon processing.
This make host CPU wakeup less under power save mode.
To make mechanisms work as usual, fw will notify driver events such as
signal change and beacon loss.
This feature needs firmware 9.9.8 or newer to support it, and driver is
compatible with older firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210426013252.5665-1-pkshih@realtek.com
Although FW crash logs are already supported for dumping in driver, the
logs may not be sufficient to analyze field issues. To improve this part,
we add a support to dump FW memory.
When driver receives FW crash notifications, driver uses DDMA, which is a
HW ability, to copy specified FW memory to FW fifo. Driver can then dump
these information from FW fifo. With this support, not only FW crash log
but also specified FW memory will be dumped while FW crash. Besides,
specified registers are also dumped.
This feature is implemeted on 8822C first due to difference of FW layouts
between ICs. In addition, we add a debugfs to trigger FW crash. It can
simulate the process of crash, dump and reset. Through it, we can also
check if a reset is ongoing.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210309060121.9099-1-pkshih@realtek.com
The variable ret is defined at the beginning and initialized
to 0 until the function returns ret, and the variable ret is
not reassigned.Therefore, we do not need to define the variable
ret, just return 0 directly at the end of the function.
Signed-off-by: wengjianfeng <wengjianfeng@yulong.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210223075438.13676-1-samirweng1979@163.com
Clear WL/BT on/off bit in scoreboard register that is used to exchange
WL/BT status. Since the status is preserved after warm reboot, we must
clear it when WL is going to down.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210219054140.7835-1-pkshih@realtek.com
Replace tasklet so we can do tx scheduling in parallel. Since throughput
is delay-sensitive in most cases, we allocate a dedicated, high priority
wq for our needs.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-5-pkshih@realtek.com
Register rrsr determines the response rate we send.
In field tests, using rate higher than current tx rate could lead
to difficulty for the receiving end to receive management/control
frames. Calculate current modulation level by tx rate then cross out
rate higher than those.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-2-pkshih@realtek.com
RFE type2 is a new NIC which has one RF antenna shares with BT.
Update phy parameter to verstion V57 to allow initial procedure
to load extra AGC table for sharing antenna NIC.
Signed-off-by: Guo-Feng Fan <vincent_fann@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210202055012.8296-4-pkshih@realtek.com
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201216130442.13869-1-zhengyongjun3@huawei.com
When driver was developed, FCC regulation didn't enable channel 144
and there was no demand for channel 144 at that time. Although HW
actually supports channel 144, driver didn't announce channel 144.
Therefore, channel 144 (20 MHz), channel 142 (40 MHz) and channel
138 (80 MHz) couldn't be used.
Today, channel 144 has been enabled by regulations and
is gradually being supported. With test requirements,
we declare hw supports channel 144.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201204013823.3729-1-pkshih@realtek.com
Some AP will not follow the power save request, or it cannot stop
transmission until its queue is empty. It may bring the decreasing of
data rate.
WLAN firmware will count is the AP still leaked packet after power save
handshake was done or not to enable WLAN slot extend mechanism.
The extend WLAN slot mechanism will extend the WLAN slot after power save
handshake, 5 ms per times, maximum is 5 times to received the leaked packet
to avoid the rate lower down.
And if the transmission was already locked at CCK rate.
The extended WLAN slot can also increase the opportunity that we can
received the CCK's long packet and be released from CCK rate.
While BT multi-link status was finished, there is possible that it still
has some packet remained for seconds. Add a timer to remain the multi-link
mechanism to protect WLAN Rx.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201126021059.11981-8-pkshih@realtek.com
The original mechanism may cause A2DP glitch during WiFi connecting AP.
Because the original TDMA may decrease too much A2DP slot.
This patch add a timer and variable to let the case A2DP + WL_Connecting
performed more well.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-9-pkshih@realtek.com
Adjust space and comments, and fix "line over 80 characters" warnings
reported by checkpatch.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201109085909.9143-5-pkshih@realtek.com
This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com
Originally driver checks if firmware has left lps via reading the setting
of REG_TCR register. But this way may fail when firmware is frequently
changing power state. Therefore, firmware provides a safer option for
driver. When firmware leaves lps successfully, it sends a C2H response
to inform driver.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-4-tehuang@realtek.com
Some functions need the support of firmware with special version.
In order to get the feature of current firmware, we store the information
in firmware header and parse after firmware is loaded. The current feature
list in firmware header includes checking leave lps via C2H and
supported lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-3-tehuang@realtek.com
This patch adds a function which is able to dump firmware fifo when
firmware crashes. If firmware needs more than one time to dump all logs,
it will set a bit called "more bit" in the header of the first log, and
driver needs to set a register to inform firmware that it is ready for the
next dump.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-5-tehuang@realtek.com
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
If rtw_core_init() fails to load the wow firmware, rtw_core_deinit()
will not get called to clean up the regular firmware.
Ensure that an error loading the wow firmware does not produce an oops
for the regular firmware by waiting on its completion to be signalled
before returning. Also release the loaded firmware.
Fixes: c8e5695eae ("rtw88: load wowlan firmware if wowlan is supported")
Cc: Chin-Yen Lee <timlee@realtek.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200920132621.26468-3-afaerber@suse.de
