The RTW_WCPU_11AC and RTW_WCPU_11N enums are used to identify two
types of microcontrollers used in Realtek chips, but these names are
misleading. The "11AC" type was also used in 11n devices (e.g.
RTL8733BU, not supported by rtw88), and the "11N" type was also used
in 11ac devices (RTL8821AU, RTL8812AU).
Rename RTW_WCPU_11AC to RTW_WCPU_3081 and RTW_WCPU_11N to RTW_WCPU_8051.
(8051 is well known. It's less clear what 3081 is, but the out of tree
drivers use this name.)
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/bfb1099c-db52-4b25-b111-17ab712e9404@gmail.com
The existing code is suitable for chips with up to 2 spatial streams.
Inform the firmware about the rates it's allowed to use when
transmitting 3 spatial streams.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/08e2f328-1aab-4e50-93ac-c1e5dd9541ac@gmail.com
The firmware message C2H_ADAPTIVITY is currently handled in
rtw_fw_c2h_cmd_rx_irqsafe(), which runs in the RX workqueue, but it's
not "irqsafe" with USB because it sleeps (reads hardware registers).
This becomes a problem after the next patch, which will create the RX
workqueue with the flag WQ_BH.
To avoid sleeping when it's not allowed, handle C2H_ADAPTIVITY in
rtw_fw_c2h_cmd_handle(), which runs in the c2h workqueue.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/96e52b03-be8d-4050-ae71-bfdb478ff42f@gmail.com
All the chips supported so far have a TX page size of 128 bytes.
Change the type of the page_size member of struct rtw_chip_info from u8
to u16 in order to support RTL8821AU (page size of 256 bytes) and
RTL8812AU (page size of 512 bytes). Also change the types of several
related variables and function parameters from u8 to u16.
The TX page size is used, among other things, to construct the beacon,
null data, QOS null data, and PS poll templates which are uploaded to
the chip's reserved page. Each template needs to be aligned on a
multiple of the TX page size. Power saving can't work if the TX page
size is wrong.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/acdefbb1-3daf-4349-9e03-9472754d5f1e@gmail.com
RTL8811AU fails to perform the 4-way handshake when the AP is too far
because it transmits the EAPOL frames at MCS9 and when that doesn't
work it retries 48 times with the same rate, to no avail.
Retrying 48 times with the same rate seems pointless. Set the
appropriate field in the TX descriptor to allow it to use lower rates
when retrying.
Set it for RTL8723D and RTL8703B because they interpret this field the
same way as RTL8811A.
The newer RTL8822C, RTL8822B, RTL8821C seem to interpret this field in
the TX descriptor differently, so leave it alone for those chips.
Tested with RTL8811AU and RTL8723DU.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/2b3e3e6f-541b-4a3b-8ca3-65b267e6a95a@gmail.com
The RTL8821AU and RTL8812AU have smaller RA report size, only 4 bytes.
Avoid the "invalid ra report c2h length" error.
Also, use a struct and u8_get_bits() to access the RA report C2H.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/c3e73c3a-fb2f-4013-9f06-d5274211e282@gmail.com
All USB devices supported by rtw88 have the same problem: they don't
transmit beacons in AP mode. (Some?) SDIO devices are also affected.
The cause appears to be clearing BIT_EN_BCNQ_DL of REG_FWHW_TXQ_CTRL
before uploading the beacon reserved page, so don't clear the bit for
USB and SDIO devices.
Tested with RTL8811CU and RTL8723DU.
Cc: <stable@vger.kernel.org> # 6.6.x
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/49de73b5-698f-4865-ab63-100e28dfc4a1@gmail.com
When wpa_supplicant is initiated by users and not by NetworkManager,
the CQM configuration might not be set. Without this setting, ICs
with connection quality monitor handled by firmware won't detect
connection loss. To fix this we prepare a default setting upon
associated at first, then update again if any is given later.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240401033019.9664-1-pkshih@realtek.com
Sometimes firmware may enter strange state or infinite
loop due to unknown bug, and then it will lead critical
function fail, such as sending H2C command or changing
power mode. In these abnormal states, we add more debug
information, including hardware register status, to help
further investigation.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016053554.744180-3-pkshih@realtek.com
Since all iterators called by 'rtw_iterate_vifs()' never uses
'mac' argument, it may be omitted, and 'struct rtw_vifs_entry'
may be simplified accordingly.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230628072327.167196-4-dmantipov@yandex.ru
Without this patch, firmware only track beacons for port 0 and since
we will always start AP on port 0, this results in misbehavior of
power saving mode on other ports after AP stops.
The "default port" H2C command is used to notify which port should
firmware track. Update the correct settings to firmware so power
saving mode can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-7-pkshih@realtek.com
Since register based H2C commands don't need endian conversion.
Introduce a new API that don't do conversion and send it directly.
New caller are expected to encode with cpu order and gradually
replace the old ones.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-6-pkshih@realtek.com
This patch allows vifs sharing same hardware with the AP mode vif to
do scan, do note that this could lead to packet loss or disconnection
of the AP's clients. Since we don't have chanctx, update scan info
upon set channel so bandwidth changes won't go unnoticed and get
misconfigured after scan. Download beacon just before scan starts to
allow hardware to get proper content to do beaconing. Last, beacons
should only be transmitted in AP's operating channel. Turn related
beacon functions off while we're in other channels so the receiving
stations won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121323.18008-1-pkshih@realtek.com
Only abort scan with current scanning VIF. If we have more than one
interface, we could call rtw_hw_scan_abort() with the wrong VIF as
input. This avoids potential null pointer being accessed when actually
the other VIF is scanning.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121312.17954-1-pkshih@realtek.com
Only gather reserved pages from AP interface after it has started. Or
else ieee80211_beacon_get_*() returns NULL and causes other VIFs'
reserved pages fail to download. Update location of current reserved page
after beacon renews so offsets changed by beacon can be recognized.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121300.17900-1-pkshih@realtek.com
The h2c.lock spinlock is used in rtw_fw_send_h2c_command() and
rtw_fw_send_h2c_packet(). Most callers call this with rtwdev->mutex
held, except from one callsite in the debugfs code. The debugfs code
alone doesn't justify the extra lock, so acquire rtwdev->mutex in
debugfs and drop the now unnecessary spinlock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202081224.2779981-5-s.hauer@pengutronix.de
8821ce is a combo card, and BT is a USB device that could get card lost
during stress test, and need WiFi firmware to detect and recover it, so
driver sends a H2C to enable this mechanism.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221128075653.5221-1-pkshih@realtek.com
For SDIO/USB interface, since the tranferring speed is slower than
that in PCIE, it may have race condition when the driver sets down
H2C command to the FW.
In the function rtw_fw_send_h2c_command, before the patch, box_reg
is written first, then box_ex_reg is written. FW starts to work and
fetch the value of box_ex_reg, when the most significant byte of
box_reg(4 bytes) is written. Meanwhile, for SDIO/USB interface,
since the transferring speed is slow, the driver is still in writing
the new value of box_ex_reg through the bus, and FW may get the
wrong value of box_ex_reg at the moment.
To prevent the above driver/FW racing situation, box_ex_reg is
written first then box_reg. Furthermore, it is written in 4 bytes at
a time, instead of written in one byte one by one. It can increase
the speed for SDIO/USB interface.
Signed-off-by: Ji-Pin Jou <neo_jou@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221124064442.28042-1-pkshih@realtek.com
The A-MSDU data needs to be stored per-link and aggregated into a single
value for the station. Add a new struct ieee_80211_sta_aggregates in
order to store this data and a new function
ieee80211_sta_recalc_aggregates to update the current data for the STA.
Note that in the non MLO case the pointer in ieee80211_sta will directly
reference the data in deflink.agg, which means that recalculation may be
skipped in that case.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a link_id parameter to ieee80211_nullfunc_get() to be
able to obtain a correctly addressed frame.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We need to flush queue before HW scan to avoid packets dropped by hardware.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-6-pkshih@realtek.com
During HW scan, the channel related feilds in hal struct changed partially.
If setting Tx power will get WARNING:rtw_get_tx_power_params() due to some
of fields in hal struct mismatch. Therefore, we fix to change all required
fields in hal struct when channel switch during HW scan.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-5-pkshih@realtek.com
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
The original timing that store OP channel info is after associated.
However, HW scan might happen before associated without backing to
OP channel, that will cause authentication or association fail.
Therefore, we modify the timing of storing OP channel info.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-4-pkshih@realtek.com
HW scan need to start queues after switch to OP channel, and stop queues
before leaving op channel. However, in original code, driver will start
queues after switch to OP channel, but stop queues until switch to OP
channel next time, that will cause packets transmitted in wrong channel.
So we fix the stop queues timing.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-3-pkshih@realtek.com
Some WSC IEs require size larger than we current supports. Extend size
to fit those demands. Separate the registered scan IE length by IC so
settings can be independent.
Since old firmware uses fewer page number, define a firmware feature to
be compatible with various firmware version.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-2-pkshih@realtek.com
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fine tune algorithm of adaptivity sensitivity to avoid disconnecting
from AP suddenly in field.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220506235045.4669-1-pkshih@realtek.com
After scan aborts we still receive some hw scan c2h packets, and
processing these c2h commands will change current channel. If device
already connect to other AP, driver will set wrong op channel due
to current channel changed. The disconnection happens when hw scan back
to wrong op channel that device can't receive beacon from AP. To fix
this issue, we ignore the late c2h if we are not scanning, and set
current channel back to op channel after scan to align the FW behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-3-pkshih@realtek.com
Correct the judgment to let beacon filter disable after disconnection.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-2-pkshih@realtek.com
This avoids below warning and makes compiler happy.
error: uninitialized symbol 'tim_offset'
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220420093058.31646-1-pkshih@realtek.com
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
Adding this allows us to get notification when bitrate configuration
of the station changes. Update according parameters to firmware so
the rate control algorithm can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-2-pkshih@realtek.com
In order to recognize the gaming controller HID, make a C2H/H2C/Mailbox
handshake to collect all the connected information from BT.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220215004855.4098-6-pkshih@realtek.com
This code needs to use skb_queue_walk_safe() instead of skb_queue_walk()
because it frees the list iterator.
Fixes: d95984b558 ("rtw88: fix memory overrun and memory leak during hw_scan")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220203082532.GA25151@kili
Previously we allocated less memory than actual required, overwrite
to the buffer causes the mm module to complaint and raise access
violation faults. Along with potential memory leaks when returned
early. Fix these by passing the correct size and proper deinit flow.
Fixes: 10d162b2ed ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-4-pkshih@realtek.com
Upon hw scan completion, idle mode is not re-entered. This might
increase power consumption under no link mode. Fix this by adding the
re-enter flow. We need another work for this since enter_ips waits
for c2h_work to finish, which might lead to deadlock if caller is in
the same work.
Fixes: 10d162b2ed ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-3-pkshih@realtek.com
ieee80211_probereq_get() can return NULL. Pointer skb should be checked
for validty before use. If it is not valid, list of skbs needs to be
freed.
Fixes: 10d162b2ed ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-2-pkshih@realtek.com
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
When fw fifo dumps, RX clock gating should be disabled to avoid
something unexpected. However, the register operation ran into
a mistake. So, we fix it.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210927111830.5354-1-pkshih@realtek.com
Current adaptivity mechanism is achieved in driver, by periodically
referencing the IGI value and then updating related registers.
But we find that this way may halt TX activity too long if huge
and temporary energy is detected frequently. So we move the mechanism
to firmware for immediately reacting this case to recover TX rapidly.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210830072014.12250-5-pkshih@realtek.com
Current flow will lead to null ptr access because of trying
to get the size of freed probe-request packets. We store the
information of packet size into rsvd page instead and also fix
the size error issue, which will cause unstable behavoir of
sending probe request by wow firmware.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210728014335.8785-6-pkshih@realtek.com
Fix erroneous code that leads to unreferenced objects. During H2C
operations, some functions returned without freeing the memory that only
the function have access to. Release these objects when they're no longer
needed to avoid potentially memory leaks.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210624023459.10294-1-pkshih@realtek.com
Don't send beacon filter h2c when there is no valid context.
Return early instead of printing out warning messages, so others
won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210528032901.12927-3-pkshih@realtek.com
It is found that driver scan could be affected by dynamic mechanism
of firmware, so we notify firmware to stop it in the scan period.
Another, firmware will detect the background noise and report to
driver for further use.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-3-pkshih@realtek.com
