Implement two parts of radar handling logic:
- cfg80211 .start_radar_detect callback to allow nl80211 to initiate CAC
- radar event to allow wlan device to advertize CAC and radar events
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Center frequency is not enough to describe the channel in HT and VHT
modes. For 40MHz and 80MHz channels both primary channel and center
frequency should be specified in order to qualify channel completely.
This change adds primary channel info into qlink_chandef structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, following parameters are needed for wireless device
configuration but were not available to it before:
- HT/VHT capabilities and capabilities masks.
- full channel info (not just IEEE number)
- BSSID hint
- previous BSSID for reassoc request
Move Management Frame Protection setting from common encr info
structure into STA-specific .connect command parameters.
Make sure that all new qlink structure definitions are alignment-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"IE set" TLV carries the same information as
qlink_event_scan_result::frame_type. Convert the event to make use of
TLV and drop frame_type member.
While at it, make qlink_event_scan_result structure alignement-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifying frame type for "IE set" TLV will allow to use several
TLVs in a single message.
Modify users accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless device may implement a logic to kick-out STA due to inactivity
for a certain period of time. This feature needs to be advertised to
higher layers if supported. Timeout value is still taken from
parameters to START_AP command, nothing changes here.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Encryption info is a constant part of STA settings, no point
to pass it as an optional TLV.
Remove QTN_TLV_ID_CRYPTO type as it's not used anymore.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce "channel definition" TLV containing full channel
description (center frequence for both segments + BW) and pass it to
wireless card in a payload to START_AP command.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify QLINK START_AP command payload to pass all AP settings
contained within struct cfg80211_ap_settings.
Make most of settings a constant part of "config AP" command
instead of passing it as an optional TLVs.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not try to cache current operational channel info in driver, this
is a potential source of synchronization issues + driver does not
really need that info.
Introduce GET_CHANNEL command and process it appropriately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, it has to report center frequency, secondary center
frequency (for 80+80) and BW.
Introduce channel definition structure to qlink and modify channel
change event processing function accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will allow to use qlink channel width values to specify BW setting
corresponding to enum nl80211_chan_width.
Current user is converted to apply BIT() macro manually to each individual
qlink_channel_width enumeration value.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify qlink command structures and interface types handling
to prepare adding AP_VLAN support to qtnfmac driver.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends supported interface type rather than mask. As a result,
types field of ieee80211_iface_limit structure may end up having
multiple iftype bits set. This leads to WARN_ON from
wiphy_verify_combinations.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements cfg80211 channel_switch handler enabling CSA
channel-switch procedure.
Driver performs only basic validation of the requested new channel
and then sends command to firmware. Beacon IEs are not sent since
beacon update is handled by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use proper endianness conversion for client station leave reason.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement current channel reporting functionality. Current operating
channel can be obtained either directly using cfg80211 get_channel
callback or from stats reported by cfg80211 survey_dump callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On startup driver obtains regulatory rules from firmware and
enables them during wiphy registration. Later on regulatory
domain change can be requested by host. In this case firmware
is notified about the upcoming changes. If the change is valid,
then firmware updates hardware channel configuration and host
driver receives updated channel info for each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for new FullMAC WiFi driver for Quantenna
QSR10G chipsets.
QSR10G (aka Pearl) is Quantenna's 8x8, 160M, 11ac offering.
QSR10G supports 2 simultaneous WMACs - one 5G and one 2G.
5G WMAC supports 160M, 8x8 configuration. FW supports
up to 8 concurrent virtual interfaces on each WMAC.
Patch introduces 2 new drivers:
- qtnfmac.ko for interfacing with kernel wireless core
- qtnfmac_pearl_pcie.ko for interfacing with hardware over PCIe interface
Signed-off-by: Dmitrii Lebed <dlebed@quantenna.com>
Signed-off-by: Sergei Maksimenko <smaksimenko@quantenna.com>
Signed-off-by: Sergey Matyukevich <smatyukevich@quantenna.com>
Signed-off-by: Bindu Therthala <btherthala@quantenna.com>
Signed-off-by: Huizhao Wang <hwang@quantenna.com>
Signed-off-by: Kamlesh Rath <krath@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
