Unify the JF configs to just one JF RF config. This can be
done because the differing fields (thermal and DCCM offsets)
won't be used for Qu MACs (and up) due to firmware support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250509104454.2582160-4-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
This should depend on both the RF (VHT/HE/EHT support) and
the MAC (<=22000 can put multiple frames into one buffer),
so unify the config in the struct iwl_cfg to just have it
sized according to the RF, and then double it for all the
MACs starting from AX210 (So/Ty).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250509104454.2582160-3-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
In some older devices, the min/max firmware API supported by
the driver depends on the specific device, when sharing the
the same MAC (config). For most newer devices, it really is
dependent on the MAC instead, since the firmware was frozen
for certain MAC types. However, in the future we expect also
freezes for RF types there.
To handle this most generally, add an API min/max to the MAC
config and then use the narrowest range prescribed by both,
if set.
For the newer MACs since 9000, move the configuration, there
was only a freeze on MAC+RF lines so far.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250509104454.2582160-2-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
There are a number of MAC parameters that are in the iwl_cfg
(which is the last config matched to the MAC/RF combination).
This isn't necessary, there are many more of those than MACs,
so move (most of) the data into the MAC family config struct.
Note that DCCM information remains for use by older devices,
and on 9000 series it'll be in struct iwl_cfg but be ignored
when the CRF is in a Qu/So platform.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-15-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
These are (going to be) base MAC parameters that are identical
even for different platforms with the same MAC, so rename the
structure accordingly, calling it iwl_family_base_params.
Also rename the pointer to it so the dereferencing is a bit
shorter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-12-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Since 9000 series devices, the devices are split into MAC and
CRF parts. Currently, "struct iwl_cfg" reflects some MAC and
some RF parameters, but we want to clean this up and move the
MAC data to what's now "struct iwl_cfg_trans_params". As the
first step, to reflect the intent, rename this structure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-9-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
This is more maintainable than the fw_name_pre prefix, and
requires fewer duplicate structs as well. Since only b0 FW
exists, override the MAC/RF steps for these devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250508121306.1277801-2-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
With just a handful of values in two bytes, the params are
smaller than the pointer to them. Inline them and save some
space.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20250506194102.3407967-14-miriam.rachel.korenblit@intel.com
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
The BW limit, cores and RF ID are matched in the subdevice ID,
so it doesn't really make sense to have both SUBDEV() match and
a match on any of those three. In particular, for Killer devices
the subdevice ID doesn't even follow the layout, so no matching
should be on those three values at all, only with SUBDEV().
Change the logic around the BW limit to have it more like all
the other things: only a bw_limit match in the dev_info, and
put the actual bandwidth into struct iwl_cfg. This duplicates a
number of those values, but that way the logic is clearer.
Add a test that checks that the three matches mentioned above
are not used in conjunction with SUBDEV(), and check that if
the bw_limit is matched, a BW limit is provided in the config.
Also check that the "Killer" devices have a SUBDEV() match.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250502155404.a185eac2736c.I87ee87300c92518a1d3296d3eda9fd4163e9085e@changeid
We have the trailing dash here, but that complicates all
the code. Simplify this by removing the dashes, adding
them to the *_MODULE_FIRMWARE macros, and adjusting the
code using this accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230621130443.72240ca13b83.I1f4ed547f0964719ed98a3ef928080462d594491@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On Bz devices, the MAC address CSRs changed from 0x380 to 0x30.
Change the boolean configuration "mac_addr_from_csr" to hold the
base address instead, and set it correctly for the different
devices using this feature.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210802215208.928c7983f014.Ic5ba92d98946c1b4640280a05dcfd75119c0f0c0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We were using a very high latency for all 9560 devices so they all
would have time to stabilize. But this causes the system to be
slighly slower, so we can use the best values for each device.
This requires a new trans cfg struct for devices with longer latency
and some adjustments to the other structs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008181047.34392f98fdb1.I3d3db14f6d1a8ecc547ca6afce8488816bd26081@changeid
These values are selected based on the PCI device ID, so the decision
to use them can be made early. By moving them to the trans_cfg, we
avoid duplicating the large cfg structs for small pieces of
data (sometimes a single boolean). This will also allow us to make
more decisions based on, for instance, the SoC type in used.
The trans_cfg concept changes a bit, because previously it was used
only to boot the device before reading further characteristics and now
it also contains more data that is associated with the device ID.
Change-Id: Ib71b07ea9e322eb74571dc5e8aa58f17eece5c9c
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl9560_2ac_cfg struct is used for PNJ devices and the
configuration is the same as iwl9260_2ac_cfg, so we can remove the
former to avoid redundancy.
Change-Id: I17ac1802f00bd80006930b922a9fc21df60e3c16
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TH1 devices can now be fully differentiated by using the device
parameters we have (particularly the RF_TYPE). Start using these
parameters instead of hardcoding to specific subsystem device IDs.
This also fixes the name of one of the TH1 devices that was
erroneously using the 9260 struct and renames 9160 to 9162.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.18d4304b5454.Ib168d186da88393e9ec46f0fca523edb48d9138e@changeid
Devices that also include a GNSS module have different names, so add a
new device option to differentiate them, according to the values we
have in the modules section of the subsystem device ID.
Additionally, convert the two applicable devices to use this value
instead of hardcoded subsystem IDs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200309091348.1f958e558d05.I45492bb57cbbeb4cc0ec84313bade4def7377a27@changeid
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new device table that contains information that can be checked
at runtime in order to decide which configuration to use. This allows
us to map the full cfg independently from the tran-specific
configuration.
This is the first step in creating the new table. Subsequent patches
will add the possibility of checking different values at runtime in
order to make the decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We needed this abstraction for some CSR registers for
IWL_DEVICE_22560, but that has been removed, so we don't need the
abstraction anymore. Remove it.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow collecting monitor data in ini debug mode.
Implement both SMEM and DRAM monitor regions dumping.
For DRAM monitor, support DBGC1, DBGC2 and DBGC3 and support several
DRAM fragments per DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add write pointer and cycle count registers to smem monitor header.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Start supporting API version 46 where applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
update the product name for the some of the cards from
the series of 9260 and 9560
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't support 9000 A-step devices anymore, so we can remove support
for loading both the a0/a0 and a0/b0 FWs.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Bump the API version to 43 for 9000 and 22000 devices.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that nvm_calib_ver is not checked in opmodes other than dvm, we
can remove it from all irrelevant configurations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These macros are useless because each one of them is used only once
and the element they are assigned to is already pretty clear about
what they mean, "nvm_hw_section_num".
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Using OTP_LOW_IMAGE_SIZE_FAMILY_8000/9000/22000 only obfuscates the
actual values, since these 3 are the same. Redefine the values per
size so it's easier to understand and compare the different
configurations.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The ht_params, nvm_ver, nvm_calib_ver and max_ht_ampdu_exponent
elements in 9000 devices are always the same. Move them to the common
macro.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
