Currently, the mac80211 layer handles construction and parsing
of 802.11 headers during packet transmission and reception.
Offloading encapsulation and decapsulation to hardware can
significantly enhance performance. Check the service bit to determine
if the firmware supports Ethernet offload. If supported, advertise the
capability to mac80211 to bypass software-based 802.11 header
processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00217-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250718025513.32982-4-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
A multi-link client can use any link for transmissions. It can decide to
put one link in power save mode for longer periods while listening on the
other links as per MLD listen interval. Unicast management frames sent to
that link station might get dropped if that link station is in power save
mode or inactive. In such cases, firmware can take decision on which link
to use.
Allow the firmware to decide on which link management frame should be
sent on, by filling the hardware link with maximum value of u32, so that
the firmware will not have a specific link to transmit data on and so
the management frames will be link agnostic. For QCN devices, all action
frames are marked as link agnostic. For WCN devices, if the device is
configured as an AP, then all frames other than probe response frames,
authentication frames, association response frames, re-association response
frames and ADDBA response frames are marked as link agnostic and if the
device is configured as a station, then all frames other than probe request
frames, authentication frames, de-authentication frames and ADDBA response
frames are marked as link agnostic.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250711091704.3704379-1-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the ACK RSSI value is not shown in station dump. Enable WMI
resource flag for ACK RSSI in WMI INIT command to add ACK RSSI value in
management TX completion event from WMI. Update ACK RSSI value obtained
in management and data frame completion path to ieee80211_tx_info. Also
advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag during hardware
register to mac80211 layer so that ACK RSSI is added to station dump
message.
Example output :
Station aa:bb:cc:dd:ee:ff (on wlp88s0)
inactive time: 46584 ms
rx bytes: 955
rx packets: 10
tx bytes: 769
tx packets: 6
tx retries: 81
tx failed: 0
rx drop misc: 0
signal: -39 dBm
signal avg: -40 dBm
tx bitrate: 6.0 MBit/s
tx duration: 1185 us
rx bitrate: 309.7 MBit/s 40MHz HE-MCS 6 HE-NSS 2 HE-GI 0 HE-DCM 0
rx duration: 0 us
last ack signal:-41 dBm
avg ack signal: -40 dBm
authorized: yes
authenticated: yes
.......
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sivashankari Madhavan <quic_sivamadh@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250709133554.622463-1-quic_ssreeela@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Install beacon protection keys in hardware for AP modes only if hardware
supports it, as indicated by the WMI service bit
WMI_TLV_SERVICE_BEACON_PROTECTION_SUPPORT. Allow keyidx up to 7, since
beacon protection uses keyidx 6 and 7.
Control this feature by setting bit 0 of feature_enable_bitmap when sending
the WMI_BCN_TMPL_CMDID command to firmware.
Check for the beacon protection enabled bit in both tx and non-tx profiles
for MBSSID cases. If set in either profile, enable the beacon protection
feature in firmware for transmitted vif.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Kathirvel <karthikeyan.kathirvel@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250604101620.2948103-1-karthikeyan.kathirvel@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.
Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-9-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Clean up unused 80P80 references as hardware does not support
it. This is applicable to both QCN9274 and WCN7850.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-8-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to set fixed HE rate/GI/LTF values using nl80211.
Reuse parts of the existing code path already used for HT/VHT
to implement the new helpers symmetrically, similar to how
HT/VHT is handled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-7-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, only the EHT IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well for AP mode. Similar
support for STA mode will be added in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-3-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, only the HE IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-2-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, the ATH12K_DEFAULT_NOISE_FLOOR (-95) is used to calculate RSSI
value, providing an estimated noise floor value. Consequently, the RSSI
value is also approximate. This works but however, using actual noise floor
value will enable the reporting of the true RSSI value.
The firmware possesses the necessary data to determine the actual noise
floor. This data is provided to the host via the WMI event
WMI_PDEV_RSSI_DBM_CONVERSION_PARAMS_INFO_EVENTID, which includes the
runtime parameters needed for calculating the real noise floor in dBm. This
event is triggered by the firmware during channel changes, temperature
offset adjustments, and hardware chainmask modifications. The individual
TLVs may not always be present in each event. For instance, temperature
information might only appear if there is a change in offset due to
temperature variation.
Add support to handle and parse this WMI event. Use the received values to
calculate and store the noise floor value.
A subsequent change will use this noise floor value in the actual RSSI
calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Co-developed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250623-support_real_noise_floor-v2-1-974bbafa317e@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
As station, WCN7850 firmware requires pairwise key to be installed before
group key. Currently host does not care about this, so it is up to kernel
or userspace to decide which one will be installed first. In case above
requirement is not met, WCN7850 firmware's EAPOL station machine is messed
up, and finally connection fails [1].
Reorder key install for station interface in that case: this is done by
caching group key first; Later when pairwise key arrives, both can be
installed in required order.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00217-QCAHKSWPL_SILICONZ-1
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218733
Link: https://lore.kernel.org/all/AS8P190MB12051DDBD84CD88E71C40AD7873F2@AS8P190MB1205.EURP190.PROD.OUTLOOK.COM # [1]
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250523-ath12k-unicast-key-first-v1-2-f53c3880e6d8@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With previous patch [1], ath12k_reg_update_chan_list() will be called
during reg_process_self_managed_hint().
reg_process_self_managed_hint() will hold rtnl_lock all the time.
But ath12k_reg_update_chan_list() may increase the occupation time of
rtnl_lock, because when wait flag is set, wait_for_completion_timeout()
will be called during 11d/hw scan.
Should minimize the occupation time of rtnl_lock as much as possible
to avoid interfering with rest of the system. So move the update channel
list operation to a new worker, so that wait_for_completion_timeout()
won't be called with the rtnl_lock held.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: f335295aa2 ("wifi: ath12k: avoid deadlock during regulatory update in ath12k_regd_update()") #[1]
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250605082528.701-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add WMI_MLO_LINK_SET_ACTIVE_CMDID command. This command allows host to
send required link information to firmware such that firmware can make
decision on activating/deactivating links in various scenarios.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-4-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Previous patches parse and save hardware MAC frequency range information
in ath12k_svc_ext_info structure. Such range represents hardware
capability hence needs to be updated based on host information, e.g. guard
the range based on host's low/high boundary.
So update frequency range. The updated range is saved in
ath12k_hw_mode_info structure and would be used when doing vdev activation
and link selection in following patches.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-3-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Firmware sends the boundary between lower and higher bands in
ath12k_wmi_dbs_or_sbs_cap_params structure embedded in
WMI_SERVICE_READY_EXT2_EVENTID event. The boundary is needed when
updating frequency range in the following patch. So parse and save
it for later use. Note ath12k_wmi_dbs_or_sbs_cap_params is placed
after some other structures, so placeholders for them are added
as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-2-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
WLAN hardware might support various hardware modes such as DBS (dual
band simultaneously), SBS (single band simultaneously) and DBS_OR_SBS
etc, see enum wmi_host_hw_mode_config_type. Firmware advertises actual
supported modes in WMI_SERVICE_READY_EXT_EVENTID event. For each mode,
firmware advertises frequency range each hardware MAC can operate on.
In MLO case such information is necessary during vdev activation and
link selection (which is done in following patches), so add a new
structure ath12k_svc_ext_info to ath12k_wmi_base, then parse and save
those information to it for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-1-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
As per IEEE 802.11be-2024 - 9.4.2.321, EHT operation element
contains MCS15 Disable subfield as the sixth bit, which is set when
MCS15 support is not enabled.
During association, firmware will use this MCS15 flag to enable or
disable the reception of PPDU with EHT-MCS15 capability.
Send MCS15 support to firmware through WMI command during peer assoc.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Dhanavandhana Kannan <quic_dhanavan1@quicinc.com>
Signed-off-by: Mohan Kumar G <quic_mkumarg@quicinc.com>
Link: https://patch.msgid.link/20250505153536.3275145-1-quic_mkumarg@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When EMLSR operation is enabled for an ML Station, EMLSR transition
timeout, padding delay and transition delay should be updated to
Firmware. Above parameters will be used by Firmware to do EMLSR operation
such as sending EML operation mode notification frame, initial control
frame etc.
Obtain above parameters from EML capabilities information present in
ieee80211_sta object and update the same to Firmware in peer assoc WMI
command sent for ML station.
MLO is not enabled in WCN7850 and hence this change is not applicable to
it as of now. This can be a leverage once it is enabled in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250327051320.3253783-5-quic_ramess@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When station is connected to a 6 GHz AP, there are 2 ways to configure the
power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to firmware,
the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to firmware which
includes more parameters for power control.
When firmware advertises WMI_TLV_SERVICE_EXT_TPC_REG_SUPPORT, it supports
WMI_VDEV_SET_TPC_POWER_CMDID, ath12k uses it to send more parameters to
firmware. As chanctx is needed to extract necessary info for this command,
save it beforehand in ath12k_mac_op_assign_vif_chanctx().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-15-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add the handler for WMI_VDEV_SET_TPC_POWER_CMDID, it is for 6 GHz band.
A subsequent patch will call this handler to send power parameters to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-14-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Save the max transmit power received in the vdev start response event from
firmware. A subsequent patch will use this to calculate the final power
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-12-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are two power types for 6 GHz regulatory, one is AP, another is
client. The client power type is used for station interface, and AP
power type is used for AP/mesh point interface.
When firmware boots up, WMI_REG_CHAN_LIST_CC_EXT_EVENTID is sent from
firmware at an early stage, the interface mode is not decided at this
point, then ath12k select reg rules of AP type as default.
After interface created, ath12k needs to update reg rules to the exact
power type matching the interface type.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-8-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
For 6 GHz band, firmware offers 3 types of regulatory rules for AP
mode and 6 for station mode in WMI_REG_CHAN_LIST_CC_EXT_EVENTID event.
In ath12k_reg_build_regd() current code by default chooses
WMI_REG_INDOOR_AP type rules from AP mode reg list to build regdomain,
regardless of the interface mode and power type, hence is not correct.
Pass interface mode (wmi_vdev_type) and AP power type
(ieee80211_ap_reg_power) as new arguments to ath12k_reg_build_regd()
such that we can choose correct rules based on them. Currently
ath12k_reg_build_regd() is called only by ath12k_reg_chan_list_event()
when driver boots, at that time these two arguments are not determined
yet, hence by default pass WMI_VDEV_TYPE_UNSPEC and
IEEE80211_REG_UNSET_AP, this results in WMI_REG_INDOOR_AP being chosen
at last. In upcoming patches the rules would be updated when these two
arguments could be determined.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-4-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Instead of storing the REO queue address inside peer entries, REO
hardware module prefers them to be stored in SRAM which could be
directly accessed by REO using peer_ID/TID based lookup table
mechanism.
Fix the enabling of the REO queue lookup table(LUT) feature by
configuring the LUT address information in the REO hardware register
and setting the host service flags.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250402152529.1649402-2-quic_nithp@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The flow of 11d scan is:
1. trigger 11d scan.
2. receive, parse, and update 11d scan result.
3. stop 11d scan.
So need to add handler for WMI_11D_SCAN_START_CMDID and
WMI_11D_SCAN_STOP_CMDID to trigger/stop 11d scan. Add process of WMI
event WMI_11D_NEW_COUNTRY_EVENTID for 11d scan result.
There are two points that need to be noted:
1. The 11d scan priority is 'MEDIUM' in firmware, the hw scan priority
is 'LOW'. When 11d scan is running, hw scan will be canceled.
To avoid this, change the hw scan priority to 'MEDIUM' when 11d scan
is running.
2. Need to add wait_for_completion_timeout() for scan.complete in
ath12k_reg_update_chan_list() because 11d scan will cost more than 5
seconds. Due to another existing wait in ath12k_scan_stop(), there will
be two scan.complete in different threads. Therefore use complete_all()
instead of complete() for scan.complete. complete_all() can work well
when it is only one thread wait for scan.complete.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-4-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, WMI_SET_INIT_COUNTRY_CMDID is used to set country code for
WCN7850 and QCN9274.
But WMI_SET_INIT_COUNTRY_CMDID is not the correct command for WCN7850.
Add handler to send WMI_SET_CURRENT_COUNTRY_CMDID to firmware, which
is used for WCN7850 to update country code.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-2-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, band define and enum are with the word 'G'. Replace it with
more appropriate 'GHZ' for clarity and correctness.
No functional changes. Only compile tested.
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Link: https://patch.msgid.link/20250324062518.2752822-5-quic_periyasa@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ8iK9QAKCRAsFbugiYzL
e9P0AP0T2yU1fl3IRw+q9toRv126vJ7eSKWDZXDU1TppGn/FMQEAiI49Jnhp6WaO
e3nbULnMVF+oOoOTWMJrJ3f6aU5C4AE=
=yTAR
-----END PGP SIGNATURE-----
Merge tag 'ath-next-20250305' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
Jeff Johnson says:
====================
ath.git patches for v6.15
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature. In addition, there was the usual
set of bug fixes and cleanups.
====================
Link: https://lore.kernel.org/linux-wireless/d01b1976-ebe8-48cd-8f49-32bfa00bed7e@oss.qualcomm.com/
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Host receives four Transmit Power Control(TPC) events from firmware on
sending TPC request. Fixed param TLV is present as part of all event to
indicate the event count and end of event. TPC config parameters along
with regulatory power array comes as first event. Rates array comes as
second and third event as it cannot be packed in single event.
Conformance Test Limit (CTL) power array comes as the fourth event.
Firmware packs different sets of array params which includes array
length and type inside master TLV as different subtlvs. And the actual
content of array is packed one after the other inside a separate TLV as
single buffer.
Parse various events and save it in local structures. Create tpc_stats
file using debugfs to store these local structures. Create function to
handle TPC stats read to relay the information to the user.
Command usage:
cat > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/tpc_stats
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250130061104.962124-2-quic_rdevanat@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The current code has ath12k_wmi_bcn_tmpl() accepting separate ar and
vdev_id parameters. However, ath12k_link_vif structure can be used to
derive both of these.
Hence, simplify the function signature.
Later change needs arvif pointer access within the function hence it is
better if arvif is directly passed now.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-1-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Fix an issue in the ath12k driver where 6 GHz operation no longer
works with new firmware.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQ/mtSHzPUi16IfDEksFbugiYzLewUCZ5PnQgAKCRAsFbugiYzL
e7fqAQD+c2nHTsGZAIhqYeXNwTYYjh26bHFuhWNJbEIjKE5D5wD+N/P72NsDzynh
bq6NFrsA9noQPnWtPX9fvoWEzPyK2gs=
=IqRH
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20250124' of git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patch for v6.14-rc
Fix an issue in the ath12k driver where 6 GHz operation no longer
works with new firmware.
Currently, the signal strength of "iw dev xxx station dump" always show an
invalid value.
This is because signal strength is only set in ath12k_mgmt_rx_event()
function, and not set for received data packet. So, change to get signal
from firmware and report to mac80211.
After that, "iw dev xxx station dump" show the correct signal strength.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 36 ms
rx bytes: 61571
rx packets: 336
tx bytes: 28204
tx packets: 205
tx retries: 49
tx failed: 0
beacon loss: 0
beacon rx: 83
rx drop misc: 66
signal: -24 dBm
beacon signal avg: -22 dBm
For WCN7850, the firmware supports db2dbm, so not need to add noise floor.
For QCN9274, the firmware not support db2dbm, so need to add noise floor.
This patch affects the station mode of WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://patch.msgid.link/20250115063537.35797-4-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the US country code, to avoid including 6 GHz rules in the 5 GHz rules
list, the number of 5 GHz rules is set to a default constant value of 4
(REG_US_5G_NUM_REG_RULES). However, if there are more than 4 valid 5 GHz
rules, the current logic will bypass the legitimate 6 GHz rules.
For example, if there are 5 valid 5 GHz rules and 1 valid 6 GHz rule, the
current logic will only consider 4 of the 5 GHz rules, treating the last
valid rule as a 6 GHz rule. Consequently, the actual 6 GHz rule is never
processed, leading to the eventual disabling of 6 GHz channels.
To fix this issue, instead of hardcoding the value to 4, use a helper
function to determine the number of 6 GHz rules present in the 5 GHz rules
list and ignore only those rules.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Cc: stable@vger.kernel.org
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123-fix_6ghz_rules_handling-v1-1-d734bfa58ff4@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to process factory test mode commands(FTM) for calibration.
By default firmware start with MISSION mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
All ath12k test mode interface related commands specified in enum
ath_tm_cmd.
When start command ATH_TM_CMD_TESTMODE_START is received, ar state
is set to test Mode and FTM daemon sends test mode command to wifi
driver via cfg80211. Wifi driver sends these command to firmware as
wmi events. If it is segmented commands it will be broken down into
multiple segments and encoded with TLV header else it is sent to
firmware as it is.
Firmware response via UTF events, wifi driver creates skb and send
to cfg80211, cfg80211 sends firmware response to FTM daemon via
netlink message.
Command to boot in ftm mode
insmod ath12k ftm_mode=1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Export ath12k_wmi_tlv_hdr() to further use in the testmode command
processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-3-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Now everything in ath12k is in place and we can enable Multi-Link Operation
(MLO) in the driver. For now it's only enabled for QCN9274 with firmware having
ATH12K_FW_FEATURE_MLO feature bit set.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, certain WMI events are frequently received by the host. Since
the host lacks the logic to process these events, the console is flooded
with ‘Unknown eventid:’ debug messages.
To address this, handle these events gracefully without printing debug
messages. There is already a block of event IDs that are ignored with a debug
print. However, this new type of event occurs more frequently, so no debug
print is necessary, and handling it should be a no-op.
While at it, re-arrange the code so that all Unknown event IDs are towards
the end of the switch block.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211154358.776279-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the multi-link
operation commands such as setup and ready to firmware before registering the
device group to mac80211.
The multi-link operation commands - setup, ready and teardown are necessary for
many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of
multi-link interfaces.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the MLO
commands such as setup, teardown and ready to firmware.
Once multi device group is ready, host has to exchange MLO setup command with
partner devices link information and followed by MLO ready command to firmware.
During deinit, MLO teardown command should be sent to firmware. Firmware would
send MLO setup complete and MLO teardown complete to host for MLO setup command
and MLO teardown command respectively.
Added WMI helper functions for the MLO setup, ready and teardown command
and the handling for corresponding event from firmware. Add appropriate WMI
tag, command id and event id to parse the event and send request.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add changes to send MLO peer assoc command with partner link details and
primary umac details.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-9-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Driver should indicate to firmware whether a peer is multi-link or not in peer
create command using multi-link flag. Add changes to support
WMI_TAG_MLO_PEER_CREATE_PARAMS in WMI_PEER_CREATE_CMDID.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-7-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Add changes to add the link vdevs dynamically whenever a channel is assigned
from mac80211 for a link vdev. During vdev create, update ML address of the
vdev to firmware using the new WMI parameter (WMI_TAG_MLO_VDEV_CREATE_PARAMS).
During vdev start, notify the firmware that this link vdev is newly added and
also indicate all its known partners so that the firmware can take necessary
actions to internally update the partners on the new link being added.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20241101151705.165987-3-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
To prepare the driver for MLO support, split the driver vif data structure to
scale for multiple links. This requires changing the use of arvif to per link
and not per hw which can now comprise of multiple links. Also since most
configurations from mac80211 are done per link, do refactoring of the driver
functions to apply these configurations at link level.
Split ath12k_vif which is the driver private of ieee80211_vif to store link
specific information as ath12k_link_vif. For default use cases the ath12k vif
will have a preallocated link vif called deflink which will be used by non ML
and the first link vif of ML vif.
With MLO support to be added, remaining link vifs will be allocated during
channel assignment where vdev create/start happens. These link vifs will be
freed during interface down.
Current ath12k_vif(arvif) structure
+---------------+ +---------------+ +---------------+
| ieee80211_vif | | ieee80211_vif | | ieee80211_vif |
| private data | | private data | | private data |
| | | | | |
| ath12k_vif | | ath12k_vif | | ath12k_vif |
| (arvif) | | (arvif) | | (arvif) |
| | | | | |
| +----------+ | | +----------+ | | +----------+ |
| |*ar (2GHz)| | | |*ar (5GHz)| | | |*ar (2GHz)| |
| +----------+ | | +----------+ | | +----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
The new ath12k_vif (ahvif) containing ath12k_link_vif(s) (arvif) (deflink is
preallocated member which is always the first link if ieee80211_vif is MLD and
is the only link otherwise):
+---------------------------------+
| ieee80211_vif |
| private data |
| |
| ath12k_vif(ahvif) |
| |
| +-------------------------------+
| |ath12k_link_vif deflink (arvif)|
| | +---------------+ |
| | | *ar(2GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(5GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(6GHz) | |
| +-------------------------------+
| |
+---------------------------------+
To refactor existing ath12k_vif to make use of link vifs, following
changes are made:
1. ath12k_vif now called by variable name ahvif storing multiple
arvifs (struct ah12k_link_vif) and also has a back pointer to ieee80211_vif.
2. In this patch set, only deflink is used to be on par with the
existing code. When MLO support is added the link id will be used to fetch
the arvif.
3. For mac80211 ops which doesn't use specific link_id, the config or info
is common for the vif, hence apply the config to all link vifs.
The links_map in the ahvif, will be used to identify all the link vifs that
are setup.
4. Change ath12k_vif_to_arvif() as ath12k_vif_to_ahvif() to fetch the
hw level vif. The link vif can be fetched from ahvif->link[], or the
deflink can be accessed via ahvif->deflink. API to access link
vif (arvif) by passing link_id can be introduced with MLO Support.
5. The ieee80211_vif can be accessed from ahvif using ath12k_ahvif_to_vif().
The locking continues to use wiphy_lock() for protecting access to most data in
struct ath12k&co, there are no changes in that regard. Though struct
ath12k_vif::link[] is protected with RCU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241015171416.518022-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
struct wmi_pdev_bss_chan_info_event is not similar to the firmware
struct definition, this will cause some random failures.
Fix by matching the struct wmi_pdev_bss_chan_info_event with the
firmware structure definition.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240331183232.2158756-3-quic_kathirve@quicinc.com
Currently, the firmware returns incorrect pdev_id information in
WMI_PDEV_BSS_CHAN_INFO_EVENTID, leading to incorrect filling of
the pdev's survey information.
To prevent this issue, when requesting BSS channel information
through WMI_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, firmware expects
pdev_id as one of the arguments in this WMI command.
Add pdev_id to the struct wmi_pdev_bss_chan_info_req_cmd and fill it
during ath12k_wmi_pdev_bss_chan_info_request(). This resolves the
issue of sending the correct pdev_id in WMI_PDEV_BSS_CHAN_INFO_EVENTID.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240331183232.2158756-2-quic_kathirve@quicinc.com
Currently, the Rx data path only supports parsing peer metadata of version
zero. However, the QCN9274 platform configures the peer metadata version
as V1B. When V1B peer metadata is parsed using the version zero logic,
invalid data is populated, causing valid packets to be dropped. To address
this issue, refactor the peer metadata version and add the version based
parsing to populate the data from peer metadata correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 2870338109 ("wifi: ath12k: add support for peer meta data version")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240624145418.2043461-1-quic_periyasa@quicinc.com
