Prefer {} to {0} in initializers since {} works even when the first
member is not a scalar.
Generated using:
sed -i 's/{[[:space:]]*0[[:space:]]*}/{}/g' drivers/net/wireless/ath/ath12k/*
Compile tested only.
Link: https://patch.msgid.link/20250720-ath12k-zero-brace-v1-1-d8c8ca9d40a8@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The QCN9274 supports two memory profiles: a default profile and a
low-memory profile. The driver signals the firmware to enable
low-memory optimizations using the QMI initialization service.
Add support to select the low-memory profile on system with less than
512 MB RAM.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.5-01651-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.1.c5-00284.1-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <aaradhana.sahu@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250708181102.4111054-5-aaradhana.sahu@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
GCC_GCC_PCIE_HOT_RST is wrongly defined for WCN7850, causing kernel crash
on some specific platforms.
Since this register is divergent for WCN7850 and QCN9274, move it to
register table to allow different definitions. Then correct the register
address for WCN7850 to fix this issue.
Note IPQ5332 is not affected as it is not PCIe based device.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Reported-by: Parth Pancholi <parth.pancholi@toradex.com>
Closes: https://lore.kernel.org/all/86899b2235a59c9134603beebe08f2bb0b244ea0.camel@gmail.com
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Tested-by: Parth Pancholi <parth.pancholi@toradex.com>
Link: https://patch.msgid.link/20250523-ath12k-wrong-global-reset-addr-v1-1-3b06eb556196@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Ath12k panic notifier is registered in driver loading process. But it is not
unregistered if ATH12K_FLAG_QMI_FAIL is set(e.g. load BDF failed) and unload
driver. It causes a dirty node in panic notifier list since ath12k panic
notifier is not unregistered from list but the buffer of this node is freed
in driver unloading process. If load driver again there will be a page fault
error due to this dirty node in panic notifier list.
This issue is caused by asymmetry between ath12k_core_init() and
ath12k_core_deinit(). Reorder and relocate the release of resources in
ath12k_core_deinit() to avoid this asymmetry issue.
Call Trace:
<TASK>
? show_regs+0x67/0x70
? __die_body+0x20/0x70
? __die+0x2b/0x40
? page_fault_oops+0x15d/0x500
? search_bpf_extables+0x63/0x90
? notifier_chain_register+0x21/0xe0
? search_exception_tables+0x5f/0x70
? kernelmode_fixup_or_oops.isra.0+0x61/0x80
? __bad_area_nosemaphore+0x179/0x240
? bad_area_nosemaphore+0x16/0x20
? do_user_addr_fault+0x312/0x7f0
? prb_read_valid+0x1c/0x30
? exc_page_fault+0x78/0x180
? asm_exc_page_fault+0x27/0x30
? notifier_chain_register+0x21/0xe0
? notifier_chain_register+0x55/0xe0
atomic_notifier_chain_register+0x2c/0x50
ath12k_core_init+0x7e/0x110 [ath12k]
ath12k_pci_probe+0xaba/0xba0 [ath12k]
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 809055628b ("wifi: ath12k: add panic handler")
Signed-off-by: Yingying Tang <quic_yintang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250423055650.16230-2-quic_yintang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The monitor mode design is:
1. Hardware captures packets on the air.
2. Hardware stores the packets into related rings.
3. When the ring buffer reaches the interrupt threshold, it triggers
the interrupt.
4. Reap and process the ring buffer in ath12k_dp_service_srng().
Here the interrupt thresholds are intr_timer_thres_us, low_threshold and
intr_batch_cntr_thres_entries. An interrupt will be triggered once:
1. Number of packets in the ring reaches intr_batch_cntr_thres_entries.
2. Number of packets in the ring reaches low_threshold(by timer).
3. Timer reaches intr_timer_thres_us.
So, add interrupt configuration for the mon status ring, then start
to process ring buffers when the interrupt arrives.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-6-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
There are several places checking if a specific bit set in
ab->fw.fw_features, and in an upcoming patch additional check needs to be
added at all places.
Introduce a new helper ath12k_fw_feature_supported() to avoid code
duplication.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250409-ath12k-wcn7850-mlo-support-v2-1-3801132ca2c3@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
At present, during PCI shutdown, the power down is only executed for a
single device. However, when operating in a group, all devices need to be
powered down simultaneously. Failure to do so will result in a firmware
assertion.
Hence, introduce a new ath12k_pci_hw_group_power_down() and call it during
power down. This will ensure that all partner devices are properly powered
down.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-5-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
With hardware grouping, during reboot, whenever a device is removed, it
powers down itself and all its partner devices in the same group. Now this
is done by all devices and hence there is multiple power down for devices
and hence the following error messages can be seen:
ath12k_pci 0002:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0002:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0002:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0003:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: POWER_OFF(3)
ath12k_pci 0003:01:00.0: failed to set mhi state DEINIT(1) in current mhi state (0x0)
ath12k_pci 0003:01:00.0: failed to set mhi state: DEINIT(1)
ath12k_pci 0004:01:00.0: failed to set mhi state POWER_OFF(3) in current mhi state (0x0)
ath12k_pci 0004:01:00.0: failed to set mhi state: POWER_OFF(3)
To prevent this, check if the ATH12K_PCI_FLAG_INIT_DONE flag is already
set before powering down. If it is set, it indicates that another partner
device has already performed the power down, and this device can skip this
step.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408-fix_reboot_issues_with_hw_grouping-v4-3-95e7bf048595@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the 'err_pci_msi_free' label is misplaced, causing the cleanup
sequence to be incorrect. Fix this by moving the 'err_pci_msi_free' label
to the correct position after 'err_irq_affinity_cleanup'.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00209-QCAHKSWPL_SILICONZ-1
Fixes: a3012f206d ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250403-ath12k-cleanup-v1-1-ad8f67b0e9cf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Extend the DMA mask to 36 bits to avoid using bounce buffers on machines
without an iommu (under OS control) similar to what was done for ath11k
in commit dbd73acb22 ("wifi: ath11k: enable 36 bit mask for stream
DMA").
This specifically avoids using bounce buffers on Qualcomm Snapdragon X
Elite machines like the Lenovo ThinkPad T14s when running at EL1.
Note that the mask could possibly be extended further but unresolved DMA
issues with 64 GiB X Elite machines currently prevents that from being
tested.
Also note that the driver is limited to 32 bits for coherent
allocations and that there is no need to check for errors when setting
masks larger than 32 bits.
Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Tested-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250321162331.19507-1-johan+linaro@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently only PCI devices are supported in Ath12k driver. Refactor
Ath12k module_init and module_exit to include Ath12k AHB support.
Add Ath12k AHB support in Kconfig with dependency on Remoteproc
driver. Ath12k AHB support relies on remoteproc driver for firmware
download, power up/down etc.
Tested-on: IPQ5332 hw1.0 AHB WLAN.WBE.1.3.1-00130-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00210-QCAHKSWPL_SILICONZ-1
Signed-off-by: Balamurugan S <quic_bselvara@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Link: https://patch.msgid.link/20250321-ath12k-ahb-v12-13-bb389ed76ae5@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
irq_set_affinity_hint() API is deprecated now, so let's use the recommended
equivalent irq_set_affinity_and_hint().
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-05266-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://patch.msgid.link/20250225053447.16824-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
If a shared IRQ is used by the driver due to platform limitation, then the
IRQ affinity hint is set right after the allocation of IRQ vectors in
ath12k_pci_msi_alloc(). This does no harm unless one of the functions
requesting the IRQ fails and attempt to free the IRQ.
This may end up with a warning from the IRQ core that is expecting the
affinity hint to be cleared before freeing the IRQ:
kernel/irq/manage.c:
/* make sure affinity_hint is cleaned up */
if (WARN_ON_ONCE(desc->affinity_hint))
desc->affinity_hint = NULL;
So to fix this issue, clear the IRQ affinity hint before calling
ath12k_pci_free_irq() in the error path. The affinity will be cleared once
again further down the error path due to code organization, but that does
no harm.
Fixes: a3012f206d ("wifi: ath12k: set IRQ affinity to CPU0 in case of one MSI vector")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://patch.msgid.link/20250225053447.16824-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of MHI error a reset work will be queued which will try
napi_disable() after napi_synchronize().
As the napi will be only enabled after qmi_firmware_ready event,
trying napi_synchronize() before napi_enable() will result in
indefinite sleep in case of a firmware crash in QMI init sequence.
To avoid this, introduce napi_enabled flag to check if napi is enabled
or not before calling napi_synchronize().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Avula Sri Charan <quic_asrichar@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250124090058.3194299-1-quic_tamizhr@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Kmemleak reported this error:
unreferenced object 0xffff1c165cec3060 (size 32):
comm "insmod", pid 560, jiffies 4296964570 (age 235.596s)
backtrace:
[<000000005434db68>] __kmem_cache_alloc_node+0x1f4/0x2c0
[<000000001203b155>] kmalloc_trace+0x40/0x88
[<0000000028adc9c8>] _request_firmware+0xb8/0x608
[<00000000cad1aef7>] firmware_request_nowarn+0x50/0x80
[<000000005011a682>] local_pci_probe+0x48/0xd0
[<00000000077cd295>] pci_device_probe+0xb4/0x200
[<0000000087184c94>] really_probe+0x150/0x2c0
The firmware memory was allocated in ath12k_pci_probe(), but not
freed in ath12k_pci_remove() in case ATH12K_FLAG_QMI_FAIL bit is
set. So call ath12k_fw_unmap() to free the memory.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.2.0-02280-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250123080226.1116479-1-quic_miaoqing@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Add support to process factory test mode commands(FTM) for calibration.
By default firmware start with MISSION mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
All ath12k test mode interface related commands specified in enum
ath_tm_cmd.
When start command ATH_TM_CMD_TESTMODE_START is received, ar state
is set to test Mode and FTM daemon sends test mode command to wifi
driver via cfg80211. Wifi driver sends these command to firmware as
wmi events. If it is segmented commands it will be broken down into
multiple segments and encoded with TLV header else it is sent to
firmware as it is.
Firmware response via UTF events, wifi driver creates skb and send
to cfg80211, cfg80211 sends firmware response to FTM daemon via
netlink message.
Command to boot in ftm mode
insmod ath12k ftm_mode=1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, single device is probed, and once firmware is ready, the device
is registered to mac80211. For Multi-Link Operation, different bands of
different devices or same device are part of a single wiphy and for
this, hardware device group abstraction is needed.
Hardware device group abstraction - when there are multiple devices (with
single radio or dual radio) that are connected by any means of interface
for communicating between them, then these devices can be combined
together as a single group using a group id to form a group abstraction
and register to mac80211.
The grouping information of multiple devices would be based on device tree
during device probe (will be implemented in future patches). If no such
information is available, then a single device will be part of group abstraction
and registered to mac80211, else multiple devices advertised in device tree are
combined and then registered to mac80211.
For device group abstraction, a base structure ath12k_hw_group (ag) and the
helpers are implemented. These helpers are used during device probe and mapping
the group to the devices involved.
An illustration of how multiple devices might be combined together in
future based on group id:
+------------------------------------------------------------------------+
| +-------------------------------------+ +-------------------+ |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | | |
| | +-----------+ | | +-----------+ | | +-----------+ | |
| | ath12k_base (ab) | | ath12k_base (ab) | |
| | (Dual band device) | | | |
| +-------------------------------------+ +-------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------------------------------+
In the above representation, two devices are combined into single group
based on group id.
Add base code changes where single device would be part of a group with an
invalid group id forming an group abstraction. Multi device grouping will
be introduced in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-4-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In the upcoming hardware device group abstraction radios across different
devices can be grouped together to support multi-link operation and register as
a device group to mac80211.
Currently, ath12k_mac_allocate() and ath12k_mac_register() are part of
ath12k_core_start() and ath12k_core_pdev_create() respectively and are based on
per device (struct ath12k_base). These APIs can be decoupled and moved out to
ath12k_core_qmi_firmware_ready() itself. This refactor is helpful for device
group abstraction when mac80211 allocate and register will be changed from per
device (struct ath12k_base) to per device group (struct ath12k_hw_group).
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241128165026.2618331-2-kvalo@kernel.org
Currently in Ath12k, tasklet is used to handle the BH context of CE
interrupts. However the tasklet is marked deprecated and has some
design flaws. To replace tasklets, BH workqueue support has been
added. BH workqueue behaves similarly to regular workqueues except
that the queued work items are executed in the BH context.
Hence, convert the tasklet to BH workqueue for handling CE interrupts
in the BH context.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241022072406.3231450-1-quic_rajkbhag@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
In case of firmware assert snapshot of firmware memory is essential for
debugging. Add firmware coredump collection support for PCI bus.
Collect RDDM and firmware paging dumps from MHI and pack them in TLV
format and also pack various memory shared during QMI phase in separate
TLVs. Add necessary header and share the dumps to user space using dev
coredump framework. Coredump collection is disabled by default and can
be enabled using menuconfig. Dump collected for a radio is 55 MB
approximately.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.2.1-00201-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240717085604.4131642-1-quic_ssreeela@quicinc.com
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
mwifiex has recently started to see active development which is good
news. rtw89 is also under active development and got several new
features. Otherwise not really anything out of ordinary.
We have one conflict in ath12k but that's easy to fix:
https://lore.kernel.org/all/20240808104348.6846e064@canb.auug.org.au/
Major changes:
mwifiex
* support for up to ten Authentication and Key Management (AKM) suites
* host MAC Sublayer Management Entity (MLME) client and AP mode support
* WPA-PSK-SHA256 AKM suite support
rtw88
* improve USB performance by aggregation
rtw89
* Wi-Fi 6 chip RTL8852BE-VT support
* WoWLAN net-detect support
* hardware encryption in unicast management frames support
* hardware rfkill support
ath12k
* DebugFS support for transmit DE stats
* Make ASPM support hardware-dependent
iwlwifi
* channel puncturing for US/CAN from UEFI
* bump FW API to 93 for BZ/SC devices
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmbYfCARHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt+Qwf/X9oQ4sf8jV6eOV7EhoWhIHnQadvo5YBZ
ulBm8In0QGjEOVWkI7kXGabKP5jhne2lVIyP1eFfP2/td/A2yDWIuEeBfDQD6f4K
aiUGAa1gs4ZtGKJBniw/ukflSqJlR99N2qBO5T/smDm3Nw/aC522SO7BoLTpoJDQ
SuW4atFHMShXYf/vIrAA2yB9ok2yw/QM+27M9qjj6D7zzqsQxDl9wKGW+2v8KiSa
rXXbfnwfaQP21CYv5xYbEPACSRSV5Dr0TNopivWYxmm9svjLzwFN2JM2fHPxBEDh
wP6Ojp+Z32c1VbQtclLrwIQdlZ5yhU5MEDlVg5VLym9F83hv+oXTbA==
=lgVx
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-09-04' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
pull-request: wireless-next-2024-09-04
here's a pull request to net-next tree, more info below. Please let me know if
there are any problems.
====================
Conflicts:
drivers/net/wireless/ath/ath12k/hw.c
38055789d1 ("wifi: ath12k: use 128 bytes aligned iova in transmit path for WCN7850")
8be12629b4 ("wifi: ath12k: restore ASPM for supported hardwares only")
https://lore.kernel.org/87msldyj97.fsf@kernel.org
Link: https://patch.msgid.link/20240904153205.64C11C4CEC2@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During PCI based hardware device start up, ASPM is disabled for all. And
once firmware is ready, it is restored back. However, not all hardwares
(for example QCN9274) supports ASPM. Hence there is a need to conditionally
restore ASPM back. Or else, for such hardwares, issue can be seen during
sending and receiving packets.
Introduce a new hardware param supports_aspm which identifies whether a
given hardware supports ASPM or not and then accordingly restore it.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240709055817.3371406-1-quic_adisi@quicinc.com
The ext interrupts are enabled when the firmware has been started, but
this may never happen, for example, if the board configuration file is
missing.
When the system is later suspended, the driver unconditionally tries to
disable interrupts, which results in an irq disable imbalance and causes
the driver to spin indefinitely in napi_synchronize().
Make sure that the interrupts have been enabled before attempting to
disable them.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Cc: stable@vger.kernel.org # 6.3
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20240709073132.9168-1-johan+linaro@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently for ath12k PCI devices, firmware could be running in one of
several execution environments, e.g., PBL, SBL and mission mode etc. Among
which PBL is the only stage where PCIe link negotiation could happen. So
normally firmware runs in PBL in order to be enumerated during system reboot.
However it might not work in kernel crash scenario: ath12k target is not
found after warm reboot from kernel crash. This is because when kernel crashes,
ath12k host does nothing to firmware. And during warm reboot, WLAN power
is sustained. So firmware is likely to keep running in mission mode throughout
the bootup process. As a result PCIe link is not established and thus target
not enumerated.
So add a handler in panic notification list for ath12k. When kernel crashes,
this handler gets called and tries to reset target to PBL state. Then PCIe
link negotiation could happen and target gets enumerated.
This change applies to all PCI devices including WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240529021533.10861-1-quic_bqiang@quicinc.com
Commit 5082b3e302 ("wifi: ath11k: fix race due to setting
ATH11K_FLAG_EXT_IRQ_ENABLED too early") fixes a race in ath11k
driver. Since ath12k shares the same logic as ath11k, currently
the race also exists in ath12k: in ath12k_pci_ext_irq_enable(),
ATH12K_FLAG_EXT_IRQ_ENABLED is set before NAPI is enabled.
In cases where only one MSI vector is allocated, this results
in a race condition: after ATH12K_FLAG_EXT_IRQ_ENABLED is set
but before NAPI enabled, CE interrupt breaks in. Since IRQ is
shared by CE and data path, ath12k_pci_ext_interrupt_handler()
is also called where we call disable_irq_nosync() to disable
IRQ. Then napi_schedule() is called but it does nothing because
NAPI is not enabled at that time, meaning that
ath12k_pci_ext_grp_napi_poll() will never run, so we have
no chance to call enable_irq() to enable IRQ back. Since IRQ
is shared, all interrupts are disabled and we would finally
get no response from target.
So port ath11k fix here, this is done by setting
ATH12K_FLAG_EXT_IRQ_ENABLED after all NAPI and IRQ work are
done. With the fix, we are sure that by the time
ATH12K_FLAG_EXT_IRQ_ENABLED is set, NAPI is enabled.
Note that the fix above also introduce some side effects:
if ath12k_pci_ext_interrupt_handler() breaks in after NAPI
enabled but before ATH12K_FLAG_EXT_IRQ_ENABLED set, nothing
will be done by the handler this time, the work will be
postponed till the next time the IRQ fires.
This is found during code review.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240524023642.37030-1-quic_bqiang@quicinc.com
Embedding net_device into structures prohibits the usage of flexible
arrays in the net_device structure. For more details, see the discussion
at [1].
Un-embed the net_device from struct ath12k_ext_irq_grp by converting it
into a pointer. Then use the leverage alloc_netdev_dummy() to allocate
the net_device object at ath12k_pci_ext_irq_config().
The free of the device occurs at ath12k_pci_free_ext_irq().
Link: https://lore.kernel.org/all/20240229225910.79e224cf@kernel.org/ [1]
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508095410.1923198-1-leitao@debian.org
Now that all infrastructure is in place and ath12k is fixed to handle all the
corner cases, power down the ath12k firmware during suspend and power it back
up during resume.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath12k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath12k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath12k's suspend callback before calling all suspend_late callbacks, making
the first condition satisfied. And because MHI devices are children of ath12k
device (ab->dev), kernel guarantees that ath12k's suspend_late callback is
called after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath12k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which would succeed
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the potential probe-defer issue when
resume.
Also change related code due to interface changes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-10-quic_bqiang@quicinc.com
Currently, when debug logs are enabled, messages such as the following
are found in the kernel log:
event mgmt rx skb pK-error len 209 ftype 00 stype 50
The "pK-error" comes from using %pK to display an skb address in an
interrupt context.
Per the guidance in the current "printk-formats" documentation, %pK
"is only intended when producing content of a file read by userspace
from e.g. procfs or sysfs, not for dmesg."
So replace %pK with %p in all of the ath12k_dbg() format strings.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240416-pk-v1-1-2c8852743e6d@quicinc.com
Currently, PCI read is failing for the registers belonging to
SECURITY_CONTROL_WLAN registers. These registers read is required
to read the board-id to identify the dual-mac QCN9274 hardware.
The failure is because, for these registers (SECURITY_CONTROL_WLAN)
offset, ath12k_pci_get_window_start() returns window_start as 0. Due
to this PCI read is done without PCI select window and with
window_start offset as 0.
Hence, fix PCI read and write by doing PCI select window and by using
the correct window_start offset - WINDOW_START for
SECURITY_CONTROL_WLAN registers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-12-quic_rajkbhag@quicinc.com
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
Most of the hal_ops are directly related to rx_desc.
Hence, split hal_ops into operations that are independent of rx_desc
(hal_ops) and the operations that are directly dependent on rx_desc
(hal_rx_ops). These hal_rx_ops depend on both hardware and firmware
hence move them out of hw_params.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-8-quic_rajkbhag@quicinc.com
Currently only one MHI device is registered successfully on platform
having two or more identical MHI devices. This is beacuse QMI service
runs with identical QRTR node ID. And, qrtr-lookup cannot register
more than one QMI service with identical node ID.
Hence, generate a unique QRTR instance ID from PCIe domain number and
bus number. QMI allows node id to be written on scratch register.
Add logic to write QRTR node id to the register. It is available for
firmware to uniquely identify an instance.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-6-quic_rajkbhag@quicinc.com
Currently ath12k only supports string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for AHB bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCI bus chip in board-2.bin.
For WCN7850, it is not enough to distinguish all different chips.
Add a new string type which includes bus, chip id, board id, vendor,
device, subsystem-vendor and subsystem-device for WCN7850.
ath12k will first load board-2.bin and searches in it for the board data
with the above parameters. If matched with one board data, ath12k downloads
it to firmware. And if not, downloads board.bin instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231216060140.30611-2-quic_bqiang@quicinc.com
This reverts commit 1f1f7d548a. The commit
caused bootup failure on QCN9274 hw2.0 platform. Incorrect hardcode DP
irq offset overwrite the CE irq, which caused the driver to miss the
mandatory bootup message from the firmware through the CE interrupt. This
occurs because the CE count differs between platforms. The revert has no
impact since the original change was based on an incorrect assumption.
Log:
ath12k_pci 0000:06:00.0: fw_version 0x1011001d fw_build_timestamp 2022-12-02 01:16 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
ath12k_pci 0000:06:00.0: failed to receive control response completion, polling..
ath12k_pci 0000:06:00.0: Service connect timeout
ath12k_pci 0000:06:00.0: failed to connect to HTT: -110
ath12k_pci 0000:06:00.0: failed to start core: -110
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20231214053215.2087308-1-quic_periyasa@quicinc.com
With VT-d disabled on Intel platform, ath12k gets only one MSI
vector. In that case, ath12k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath12k has
no chance to reconfig it to HW srngs during this phase, thus
ath12k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-8-quic_kangyang@quicinc.com
Current code enables ASPM by default, it allows MHI to enter M2 state.
In case of one MSI vector, system hang is observed if ath12k does MHI
register reading in this state.
The workaround here is to prevent MHI from entering M2 state, this can
be done by disabling ASPM if only one MSI vector is used. When using 32
vectors ASPM is enabled as before.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-7-quic_kangyang@quicinc.com
On some platforms it's not possible to allocate 32 MSI vectors for
various reasons, maybe kernel configuration, VT-d disabled, buggy BIOS
etc. So ath12k was not able to use WCN7850 PCI devices on those
platforms. Add support for one MSI vector to solve that.
In case of one MSI vector, interrupt migration needs to be disabled.
This is because when interrupt migration happens, the msi_data may
change. However, msi_data is already programmed to rings during initial
phase and ath12k has no way to know that msi_data is changed during run
time and reprogram again.
In case of one MSI vector, MHI subsystem should not use IRQF_NO_SUSPEND
as WCN7850 doesn't set this flag too. Ath12k doesn't need to leave IRQ
enabled in suspend state.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-6-quic_kangyang@quicinc.com
This is to prepare for one MSI vector support. IRQ enable and disable
of CE and DP are done only in case of multiple MSI vectors.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-5-quic_kangyang@quicinc.com
Like ATH12K_PCI_IRQ_CE0_OFFSET, define ATH12K_PCI_IRQ_DP_OFFSET for
DP to save the IRQ instead of base_vector from MSI config.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-4-quic_kangyang@quicinc.com
Add two flags to indicate whether IRQ handler for CE and DP can be called.
This is because in one MSI vector case, interrupt is not disabled in
hif_stop and hif_irq_disable. So if interrupt is disabled, MHI interrupt
is disabled too.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-3-quic_kangyang@quicinc.com
The reservation mode of interrupts in kernel assigns a dummy vector
when the interrupt is allocated and assigns a real vector when the
request_irq is called. The reservation mode helps to ease vector
pressure when devices with a large amount of queues/interrupts are
initialized, but only a minimal subset of those queues/interrupts
is actually used.
So on reservation mode, the msi_data may change after request_irq is
called, then it will lead to spurious interrupt. But when VT-d in
BIOS is enabled and ath12k can get 32 MSI vectors, ath12k always get
the same msi_data before and after request_irq.
So in case of one MSI vector, ath12k need read msi_data again after
request_irq is called, and then the correct msi_data is programmed
into WCN7850 hardware components.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231121021304.12966-2-quic_kangyang@quicinc.com
In PCI and HAL interface layer module, the identifier sc is used
to represent an instance of ath12k_base structure. However,
within ath12k, the convention is to use "ab" to represent an SoC
"base" struct. So change the all instances of sc to ab.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231018153008.29820-3-quic_periyasa@quicinc.com
-----BEGIN PGP SIGNATURE-----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=iFFM
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Add locking to read/modify/write PCIe Capability Register accessors
for Link Control and Root Control
- Use pci_dev_id() when possible instead of manually composing ID
from dev->bus->number and dev->devfn
Resource management:
- Move prototypes for __weak sysfs resource files to linux/pci.h to
fix 'no previous prototype' warnings
- Make more I/O port accesses depend on HAS_IOPORT
- Use devm_platform_get_and_ioremap_resource() instead of open-coding
platform_get_resource() followed by devm_ioremap_resource()
Power management:
- Ensure devices are powered up while accessing VPD
- If device is powered-up, keep it that way while polling for PME
- Only read PCI_PM_CTRL register when available, to avoid reading the
wrong register and corrupting dev->current_state
Virtualization:
- Avoid Secondary Bus Reset on NVIDIA T4 GPUs
Error handling:
- Remove unused pci_disable_pcie_error_reporting()
- Unexport pci_enable_pcie_error_reporting(), used only by aer.c
- Unexport pcie_port_bus_type, used only by PCI core
VGA:
- Simplify and clean up typos in VGA arbiter
Apple PCIe controller driver:
- Initialize pcie->nvecs (number of available MSIs) before use
Broadcom iProc PCIe controller driver:
- Use of_property_read_bool() instead of low-level accessors for
boolean properties
Broadcom STB PCIe controller driver:
- Assert PERST# when probing BCM2711 because some bootloaders don't
do it
Freescale i.MX6 PCIe controller driver:
- Add .host_deinit() callback so we can clean up things like
regulators on probe failure or driver unload
Freescale Layerscape PCIe controller driver:
- Add support for link-down notification so the endpoint driver can
process LINK_DOWN events
- Add suspend/resume support, including manual
PME_Turn_off/PME_TO_Ack handshake
- Save Link Capabilities during probe so they can be restored when
handling a link-up event, since the controller loses the Link Width
and Link Speed values during reset
Intel VMD host bridge driver:
- Fix disable of bridge windows during domain reset; previously we
cleared the base/limit registers, which actually left the windows
enabled
Marvell MVEBU PCIe controller driver:
- Remove unused busn member
Microchip PolarFlare PCIe controller driver:
- Fix interrupt bit definitions so the SEC and DED interrupt handlers
work correctly
- Make driver buildable as a module
- Read FPGA MSI configuration parameters from hardware instead of
hard-coding them
Microsoft Hyper-V host bridge driver:
- To avoid a NULL pointer dereference, skip MSI restore after
hibernate if MSI/MSI-X hasn't been enabled
NVIDIA Tegra194 PCIe controller driver:
- Revert 'PCI: tegra194: Enable support for 256 Byte payload' because
Linux doesn't know how to reduce MPS from to 256 to 128 bytes for
endpoints below a switch (because other devices below the switch
might already be operating), which leads to 'Malformed TLP' errors
Qualcomm PCIe controller driver:
- Add DT and driver support for interconnect bandwidth voting for
'pcie-mem' and 'cpu-pcie' interconnects
- Fix broken SDX65 'compatible' DT property
- Configure controller so MHI bus master clock will be switched off
while in ASPM L1.x states
- Use alignment restriction from EPF core in EPF MHI driver
- Add Endpoint eDMA support
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driversupport
- Add MHI eDMA support
- Add Snapdragon SM8450 support to the EPF MHI driver
- Use iATU for EPF MHI transfers smaller than 4K to avoid eDMA setup
latency
- Add sa8775p DT binding and driver support
Rockchip PCIe controller driver:
- Use 64-bit mask on MSI 64-bit PCI address to avoid zeroing out the
upper 32 bits
SiFive FU740 PCIe controller driver:
- Set the supported number of MSI vectors so we can use all available
MSI interrupts
Synopsys DesignWare PCIe controller driver:
- Add generic dwc suspend/resume APIs (dw_pcie_suspend_noirq() and
dw_pcie_resume_noirq()) to be called by controller driver
suspend/resume ops, and a controller callback to send PME_Turn_Off
MicroSemi Switchtec management driver:
- Add support for PCIe Gen5 devices
Miscellaneous:
- Reorder and compress to reduce size of struct pci_dev
- Fix race in DOE destroy_work_on_stack()
- Add stubs to avoid casts between incompatible function types
- Explicitly include correct DT includes to untangle headers"
* tag 'pci-v6.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (96 commits)
PCI: qcom-ep: Add ICC bandwidth voting support
dt-bindings: PCI: qcom: ep: Add interconnects path
PCI: qcom-ep: Treat unknown IRQ events as an error
dt-bindings: PCI: qcom: Fix SDX65 compatible
PCI: endpoint: Add kernel-doc for pci_epc_mem_init() API
PCI: epf-mhi: Use iATU for small transfers
PCI: epf-mhi: Add support for SM8450
PCI: epf-mhi: Add eDMA support
PCI: qcom-ep: Add eDMA support
PCI: epf-mhi: Make use of the alignment restriction from EPF core
PCI/PM: Only read PCI_PM_CTRL register when available
PCI: qcom: Add support for sa8775p SoC
dt-bindings: PCI: qcom: Add sa8775p compatible
PCI: qcom-ep: Pass alignment restriction to the EPF core
PCI: Simplify pcie_capability_clear_and_set_word() control flow
PCI: Tidy config space save/restore messages
PCI: Fix code formatting inconsistencies
PCI: Fix typos in docs and comments
PCI: Fix pci_bus_resetable(), pci_slot_resetable() name typos
PCI: Simplify pci_dev_driver()
...
A mouse that uses a USB connection is called a "USB mouse" device (or
"USB mouse" for short), not a "mouse USB" device. By analogy, a WiFi
adapter that connects to the host computer via USB is a "USB wireless"
device, not a "wireless USB" device. (The latter term more properly
refers to a defunct Wireless USB specification, which described a
technology for sending USB protocol messages over an ultra wideband
radio link.)
Similarly for a WiFi adapter card that plugs into a PCIe slot: It is a
"PCIe wireless" device, not a "wireless PCIe" device.
Rephrase the text in the kernel source where the word ordering is
wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/57da7c80-0e48-41b5-8427-884a02648f55@rowland.harvard.edu
Don't assume that only the driver would be accessing LNKCTL. ASPM policy
changes can trigger write to LNKCTL outside of driver's control.
Use RMW capability accessors which do proper locking to avoid losing
concurrent updates to the register value. On restore, clear the ASPMC field
properly.
Suggested-by: Lukas Wunner <lukas@wunner.de>
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Link: https://lore.kernel.org/r/20230717120503.15276-10-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
This is to check the hardware major version for WCN7850 so only
supported hardware is initialized. Now only WCN7850 with major
version 2 is supported.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230518105741.1281424-1-quic_cjhuang@quicinc.com
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323112613.7550-3-cai.huoqing@linux.dev
Smatch Warns:
drivers/net/wireless/ath/ath12k/pci.c:1198 ath12k_pci_probe()
warn: missing unwind goto?
Store the error value in ret and use correct label with a goto.
Only Compile tested, found with Smatch.
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/all/Y+426q6cfkEdb5Bv@kili/
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230307104706.240119-1-harshit.m.mogalapalli@oracle.com
Wakeup/release MHI is not needed before pci_read/write for QCN9274.
Since wakeup & release MHI is enabled for all QCN9274 and
WCN7850, below MHI assert is seen in QCN9274
[ 784.906613] BUG: sleeping function called from invalid context at drivers/bus/mhi/host/pm.c:989
[ 784.906633] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 0, name: swapper/3
[ 784.906637] preempt_count: 503, expected: 0
[ 784.906641] RCU nest depth: 0, expected: 0
[ 784.906644] 2 locks held by swapper/3/0:
[ 784.906646] #0: ffff8ed348e429e0 (&ab->ce.ce_lock){+.-.}-{2:2}, at: ath12k_ce_recv_process_cb+0xb3/0x2f0 [ath12k]
[ 784.906664] #1: ffff8ed348e491f0 (&srng->lock_key#3){+.-.}-{2:2}, at: ath12k_ce_recv_process_cb+0xfb/0x2f0 [ath12k]
[ 784.906678] Preemption disabled at:
[ 784.906680] [<0000000000000000>] 0x0
[ 784.906686] CPU: 3 PID: 0 Comm: swapper/3 Tainted: G W O 6.1.0-rc2+ #3
[ 784.906688] Hardware name: Intel(R) Client Systems NUC8i7HVK/NUC8i7HVB, BIOS HNKBLi70.86A.0056.2019.0506.1527 05/06/2019
[ 784.906690] Call Trace:
[ 784.906691] <IRQ>
[ 784.906693] dump_stack_lvl+0x56/0x7b
[ 784.906698] __might_resched+0x21c/0x270
[ 784.906704] __mhi_device_get_sync+0x7d/0x1c0 [mhi]
[ 784.906714] mhi_device_get_sync+0xd/0x20 [mhi]
[ 784.906719] ath12k_pci_write32+0x75/0x170 [ath12k]
[ 784.906729] ath12k_hal_srng_access_end+0x55/0xc0 [ath12k]
[ 784.906737] ath12k_ce_recv_process_cb+0x1f3/0x2f0 [ath12k]
[ 784.906776] ? ath12k_pci_ce_tasklet+0x11/0x30 [ath12k]
[ 784.906788] ath12k_pci_ce_tasklet+0x11/0x30 [ath12k]
[ 784.906813] tasklet_action_common.isra.18+0xb7/0xe0
[ 784.906820] __do_softirq+0xd0/0x4c9
[ 784.906826] irq_exit_rcu+0x88/0xe0
[ 784.906828] common_interrupt+0xa5/0xc0
[ 784.906831] </IRQ>
[ 784.906832] <TASK>
Adding function callbacks for MHI wakeup and release operations.
QCN9274 does not need wakeup/release, function callbacks are initialized
to NULL. In case of WCN7850, shadow registers are used to access rings.
Since, shadow register's offset is less than ACCESS_ALWAYS_OFF,
mhi_device_get_sync() or mhi_device_put() to wakeup
and release mhi will not be called during service ring accesses.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-03171-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230123095141.5310-1-quic_rgnanase@quicinc.com
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
