Add support to configure maximum NSS in 160 MHz bandwidth.
Firmware advertises support for handling NSS ratio information
as a part of service ready ext event using nss_ratio_enabled
flag. Save this information in ath12k_pdev_cap to calculate
NSS ratio.
Additionally, reorder the code by moving
ath12k_peer_assoc_h_phymode() before ath12k_peer_assoc_h_vht()
to ensure that arg->peer_phymode correctly reflects the bandwidth
in the max NSS calculation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-9-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, only the HE IE in management frames is updated with
respect to MU-MIMO configurations, but this change is not
reflected in the hardware. Add support to propagate MU-MIMO
configurations to the hardware as well.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Co-developed-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://patch.msgid.link/20250701010408.1257201-2-quic_pradeepc@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When two split-phy devices that support overlapping frequency ranges within
the same band(say 5 GHz low and 5 GHz high) are grouped into an ath12k
hardware (HW) setup, they share a common wiphy instance. Consequently, the
channel list (wiphy->bands[]) becomes unified across all associated
radios (ar).
When a scan is triggered with frequency list containing frequencies of
both 5 GHz low and 5 GHz high, mac80211 generates a single scan request
to driver with all the frequencies. This is because mac80211 splits the
scan request based on band.
ath12k checks the first frequency in the requested scan frequency list and
initiates scan to corresponding radio's(ar) firmware with all the
frequencies. Firmware rejects this scan since some of the frequencies in
the scan request are not supported, resulting in a scan failure.
To fix this ath12k driver should split the scan request into multiple
scans based on requested frequencies and schedule them to corresponding
underlying radio(s) in parallel.
Currently, ath12k driver assigns the scan link (link 15) in ahvif->links[]
for scan vdev creation. However, with parallel scan support being
introduced in the following patch, multiple radios (e.g., 5 GHz low and
5 GHz high) in the same HW group may attempt to use the same scan link
concurrently, causing conflicts where the vdev created by one radio could
be deleted and re-initialized by another.
To address this, reserve space for additional scan links for each radio in
a MLO group and allow subsequent radios to use different available scan
links (ahvif->link[15..MAX_SCAN_LINKS]) when scan link (15) is
pre-occupied.
While at it, rename ATH12K_DEFAULT_SCAN_LINK as ATH12K_FIRST_SCAN_LINK
as there is no longer only one scan link.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250507194832.2501668-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of two links established on the same device in an ML connection,
depending on device's hardware mode capability, it is possible that both
links fall on the same MAC. Currently, no specific action is taken to
address this but just keep both links active. However this would result
in lower throughput compared to even one link, because switching between
these two links on the resulted MAC significantly impacts throughput.
Check if both links fall in the frequency range of a single MAC. If
so, send WMI_MLO_LINK_SET_ACTIVE_CMDID command to firmware such that
firmware can deactivate one of them. Note the decision of which link
getting deactivated is made by firmware, host only sends the vdev
lists.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.1.c5-00284-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250522-ath12k-sbs-dbs-v1-5-54a29e7a3a88@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Prepare the parameters which are needed for WMI command
WMI_VDEV_SET_TPC_POWER_CMDID. This helper will be used in a following
patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-13-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The Transmit Power Envelope element conveys the local maximum transmit
power for various transmission bandwidths, this element is present in
various frames, e.g. beacon and probe response etc, transmitted by AP.
A station shall determine a local maximum transmit power from it.
So parse and save them for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-11-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In a subsequent change, the frequency range needs to be updated with
each regulatory update. Since the current function also modifies the
DISABLED flag in the actual channel list, which should always align
with hardware-supported start and end frequencies rather than the
current operating ones, the existing function cannot be called again.
Therefore, the logic for setting the frequency range needs to be
refactored.
To address this, refactor the frequency setting part into a new
helper function, ath12k_mac_update_freq_range(). Since this needs
to be done independently of updating the DISABLED flag, call the new
helper function ath12k_mac_update_freq_range() after updating the
channel list for each band.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250408042128.720263-2-quic_rajson@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The flow of 11d scan is:
1. trigger 11d scan.
2. receive, parse, and update 11d scan result.
3. stop 11d scan.
So need to add handler for WMI_11D_SCAN_START_CMDID and
WMI_11D_SCAN_STOP_CMDID to trigger/stop 11d scan. Add process of WMI
event WMI_11D_NEW_COUNTRY_EVENTID for 11d scan result.
There are two points that need to be noted:
1. The 11d scan priority is 'MEDIUM' in firmware, the hw scan priority
is 'LOW'. When 11d scan is running, hw scan will be canceled.
To avoid this, change the hw scan priority to 'MEDIUM' when 11d scan
is running.
2. Need to add wait_for_completion_timeout() for scan.complete in
ath12k_reg_update_chan_list() because 11d scan will cost more than 5
seconds. Due to another existing wait in ath12k_scan_stop(), there will
be two scan.complete in different threads. Therefore use complete_all()
instead of complete() for scan.complete. complete_all() can work well
when it is only one thread wait for scan.complete.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250401020840.357-4-quic_kangyang@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Driver does not support get_txpower mac ops because of which
cfg80211 returns vif->bss_conf.txpower to user space. bss_conf.txpower
gets its value from ieee80211_channel->max_reg_power. However, the final
txpower is dependent on few other parameters apart from max regulatory
supported power. It is the firmware which knows about all these
parameters and considers the minimum for each packet transmission.
All ath12k firmware reports the final TX power in firmware pdev stats
which falls under fw_stats. add get_txpower mac ops to get the TX power
from firmware leveraging fw_stats and return it accordingly.
While at it, there is a possibility that repeated stats request WMI
commands are queued to FW if mac80211/userspace does get tx power back
to back(in Multiple BSS cases). This could potentially consume the WMI
queue completely. Hence limit this by fetching the power only for every
5 seconds and reusing the value until the refresh timeout or when there
is a change in channel.
Also remove init_completion(&ar->fw_stats_complete) in
ath12k_mac_hw_register() as ath12k_fw_stats_init() takes care of
it for each ar.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-3-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Signed-off-by: Rameshkumar Sundaram <rameshkumar.sundaram@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250306102215.1300522-2-rameshkumar.sundaram@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
The driver is informed of the counter offsets in the beacon during CSA
through the ieee80211_mutable_offsets structure. According to the
documentation for the cntdwn_counter_offs member, "This array can contain
zero values which should be ignored." However, the current implementation
uses these values unconditionally, without checking for zeros.
Whenever CSA is active, these offsets are guaranteed to be set. Therefore,
add a check for CSA active status before setting the CSA switch count
offsets. This ensures that the offsets are only set when CSA is active,
preventing incorrect configurations.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-2-420c42fcfecf@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, the transmit rate of "iw dev xxx station dump" command
always show an invalid value.
To address this issue, ath12k parse the info of transmit complete
report from firmware and indicate the transmit rate to mac80211.
This patch affects the station mode of WCN7850 and QCN9274.
After that, "iw dev xxx station dump" show the correct transmit rate.
Such as:
Station 00:03:7f:12:03:03 (on wlo1)
inactive time: 872 ms
rx bytes: 219111
rx packets: 1133
tx bytes: 53767
tx packets: 462
tx retries: 51
tx failed: 0
beacon loss: 0
beacon rx: 403
rx drop misc: 74
signal: -95 dBm
beacon signal avg: -18 dBm
tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715
Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
ieee80211_radar_detected() expects the driver to pass a channel context
configuration during MLO. This is used to identify exactly which link
detected the radar.
Add support to pass this to mac80211. Since the link arvif is not known in
the WMI event, introduce a helper iterator API,
ath12k_mac_get_any_chanctx_conf_iter(), to get the channel context
configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-3-058e783bcfc7@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
In case of multi device group abstraction, host has to exchange the multi-link
operation commands such as setup and ready to firmware before registering the
device group to mac80211.
The multi-link operation commands - setup, ready and teardown are necessary for
many commands such as WMI_PEER_ASSOC_CMD, WMI_BCN_TMPL_CMD in case of
multi-link interfaces.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241211153432.775335-8-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
Currently, hardware abstractions (ah) of different radio bands are tightly
coupled to a single device (ab). But, with hardware device group abstraction
(ag), multiple radios across different devices in a group can form different
combinations of hardware abstractions (ah) within the group. Hence, the mapping
between ah to ab can be removed and instead it can be mapped with struct
ath12k_hw_group (ag).
Current mapping between struct ath12k_hw (ah), struct ath12k_base (ab) and struct
ath12k_hw_group (ag):
+------------------------------------------------+
| +-------------------------------------+ |
| | +---------------+ +---------------+ | |
| | |ath12k_hw (ah) | |ath12k_hw (ah) | | |
| | +---------------+ +---------------+ | |
| | | |
| | +-----------+ | +-----------+ | |
| | | ar (2GHz) | | | ar (5GHz) | | |
| | +-----------+ | +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+------------------------------------------------+
After hardware device group abstraction moving ah array out of ab to ag:
+----------------------------------------------+
| +---------------+ +---------------+ |
| |ath12k_hw (ah) | |ath12k_hw (ah) | |
| +---------------+ +---------------+ |
| +-------------------------------------+ |
| | +-----------+ +-----------+ | |
| | | ar (2GHz) | | ar (5GHz) | | |
| | +-----------+ +-----------+ | |
| | Dual band device-1 (ab) | |
| +-------------------------------------+ |
| ath12k_hw_group (ag) based on group id |
+----------------------------------------------+
This decoupling of struct ath12k_hw (ah) from struct ath12k_base (ab) and
mapping it to struct ath12k_hw_group (ag) will help in forming different
combinations of multi-link devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241204163216.433795-6-kvalo@kernel.org
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
When a scan request is received, driver selects a link id for which the arvif
can be mapped. Same link is also used for getting the link conf address.
Currently, we return 0 as link id for a non ML vif, which is correct since that
is the default link id. Also when any of the link vif is active and the scan
request is for a channel in the active link we return its link id. But, when we
don't hit both of the above cases (i.e not a ML vif or no active link vif for
the channel is present) we currently return 0 as the link id.
Bu the problemis that this might not work out always, eg., when only one link
(eg. linkid = 1) is added to vif, then we won't find any link conf for link id
0 in the vif resulting in scan failure. During AP bringup, such scan failure
causes bringup issues. Hence avoid sending link id 0 as default. Rather use a
default link for scan and default link address for the same. This scan vdev
will either be deleted if another scan is requested on same vif or when AP is
broughtup on same link or during interface cleanup.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241126171139.2350704-7-kvalo@kernel.org
Add changes to handle multi-link station state change with proper
link handling and add code changes for ML peer creation, peer deletion.
In ath12k_mac_assign_link_sta() initialise all arsta fields first and only then
call rcu_assign_pointer(). This is to make sure that readers don't have access
to arsta which is still modified.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241121155806.1862733-2-kvalo@kernel.org
To prepare the driver for MLO support, split the driver vif data structure to
scale for multiple links. This requires changing the use of arvif to per link
and not per hw which can now comprise of multiple links. Also since most
configurations from mac80211 are done per link, do refactoring of the driver
functions to apply these configurations at link level.
Split ath12k_vif which is the driver private of ieee80211_vif to store link
specific information as ath12k_link_vif. For default use cases the ath12k vif
will have a preallocated link vif called deflink which will be used by non ML
and the first link vif of ML vif.
With MLO support to be added, remaining link vifs will be allocated during
channel assignment where vdev create/start happens. These link vifs will be
freed during interface down.
Current ath12k_vif(arvif) structure
+---------------+ +---------------+ +---------------+
| ieee80211_vif | | ieee80211_vif | | ieee80211_vif |
| private data | | private data | | private data |
| | | | | |
| ath12k_vif | | ath12k_vif | | ath12k_vif |
| (arvif) | | (arvif) | | (arvif) |
| | | | | |
| +----------+ | | +----------+ | | +----------+ |
| |*ar (2GHz)| | | |*ar (5GHz)| | | |*ar (2GHz)| |
| +----------+ | | +----------+ | | +----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
The new ath12k_vif (ahvif) containing ath12k_link_vif(s) (arvif) (deflink is
preallocated member which is always the first link if ieee80211_vif is MLD and
is the only link otherwise):
+---------------------------------+
| ieee80211_vif |
| private data |
| |
| ath12k_vif(ahvif) |
| |
| +-------------------------------+
| |ath12k_link_vif deflink (arvif)|
| | +---------------+ |
| | | *ar(2GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(5GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(6GHz) | |
| +-------------------------------+
| |
+---------------------------------+
To refactor existing ath12k_vif to make use of link vifs, following
changes are made:
1. ath12k_vif now called by variable name ahvif storing multiple
arvifs (struct ah12k_link_vif) and also has a back pointer to ieee80211_vif.
2. In this patch set, only deflink is used to be on par with the
existing code. When MLO support is added the link id will be used to fetch
the arvif.
3. For mac80211 ops which doesn't use specific link_id, the config or info
is common for the vif, hence apply the config to all link vifs.
The links_map in the ahvif, will be used to identify all the link vifs that
are setup.
4. Change ath12k_vif_to_arvif() as ath12k_vif_to_ahvif() to fetch the
hw level vif. The link vif can be fetched from ahvif->link[], or the
deflink can be accessed via ahvif->deflink. API to access link
vif (arvif) by passing link_id can be introduced with MLO Support.
5. The ieee80211_vif can be accessed from ahvif using ath12k_ahvif_to_vif().
The locking continues to use wiphy_lock() for protecting access to most data in
struct ath12k&co, there are no changes in that regard. Though struct
ath12k_vif::link[] is protected with RCU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241015171416.518022-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Pdev id from mac phy capabilities will be sent as a part of
HTT/WMI command to firmware. This causes issue with single pdev
devices where firmware does not respond to the WMI/HTT request
sent from host.
For single pdev devices firmware expects pdev id as 1 for 5 GHz/6 GHz
phy and 2 for 2 GHz band. Add wrapper ath12k_mac_get_target_pdev_id()
to help fetch right pdev for single pdev devices.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240621102809.3984004-1-quic_rgnanase@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
So enable keepalive before going to suspend and disable it after
resume back.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-9-quic_bqiang@quicinc.com
When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
In order to send out all packets before going to suspend, current code
adds a 500ms delay as a workaround. It is a rough estimate and may not
work.
Fix this by checking packet counters, if counters become zero, then all
packets are sent out or dropped.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412060620.27519-7-quic_bqiang@quicinc.com
To support multi link operation, we need to combine all the link/pdev
under a single wiphy. This avoids the overhead of synchronization
across multiple hardware instances in both the cfg80211 and mac80211
layers. Currently, each link/pdev is registered as separate wiphy,
tightly coupled with link/pdev/radio (ar) structure. To enable single
wiphy registration within the chip, we decouple the wiphy data entity from
the link/pdev/radio (ar) structure and move it under the chip (ab)
structure with a new data container (ath12k_hw) structure. This approach
improves scalability for future multi link operation support.
mac80211 hw private data structure diagram
------------------------------------------
Now After
+---------------------+ +---------------------+
|mac80211 hw priv data| |mac80211 hw priv data|
| | | |
| | | |
| | | |
| | | ath12k_hw (ah) |
| | | |
| | +-------------------> | |
| ath12k (ar) | | +-------------+ |
| | | | | |
| | | | ath12k (ar) | |
| | | | | |
| | | | | |
| | | +-------------+ |
| | | |
| | | |
+---------------------+ +---------------------+
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240118010320.3918136-3-quic_periyasa@quicinc.com
Add 320 MHz bandwidth as a new bandwidth enum for ATH12k driver. This
is extending existing bandwidth related enums to include 320 MHz. This
is a precursor to supporting 320 MHz in the future.
Sanity test performed to confirm that there was no impact in existing
bandwidths.
Additionally update QuIC copyright to include 2023 in hal_rx.h.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231116221839.1303170-1-quic_msinada@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
Add support to retrieve and configure the phy modes supported
by the hardware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-6-quic_alokad@quicinc.com
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
