dwmac510_tc_ops and dwxgmac_tc_ops are completely identical,
keep dwmac510_tc_ops to provide better backward compatibility.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Link: https://patch.msgid.link/20241212033325.282817-1-0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit b8c43360f6 ("net: stmmac: No need to calculate speed divider
when offload is disabled") allows the "port_transmit_rate_kbps" to be
set to a value of 0, which is then passed to the "div_s64" function when
tc-cbs is disabled. This leads to a zero-division error.
When tc-cbs is disabled, the idleslope, sendslope, and credit values the
credit values are not required to be configured. Therefore, adding a return
statement after setting the txQ mode to DCB when tc-cbs is disabled would
prevent a zero-division error.
Fixes: b8c43360f6 ("net: stmmac: No need to calculate speed divider when offload is disabled")
Cc: <stable@vger.kernel.org>
Co-developed-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Signed-off-by: KhaiWenTan <khai.wen.tan@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240918061422.1589662-1-khai.wen.tan@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ethtool --show-mm can get real-time state of FPE.
fpe_irq_status logs should keep quiet.
tc-taprio can always query driver state, delete unbalanced logs.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/39943d7967f291674a97ef0572878aca273087e9.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drop driver defined stmmac_fpe_state, and switch to common
ethtool_mm_verify_status for local TX verification status.
Local side and remote side verification processes are completely
independent. There is no reason at all to keep a local state and
a remote state.
Add a spinlock to avoid races among ISR, timer, link update
and register configuration.
This patch is based on Vladimir Oltean's proposal.
Vladimir Oltean says:
====================
In the INITIAL state, the timer sends MPACKET_VERIFY. Eventually the
stmmac_fpe_event_status() IRQ fires and advances the state to VERIFYING,
then rearms the timer after verify_time ms. If a subsequent IRQ comes in
and modifies the state to SUCCEEDED after getting MPACKET_RESPONSE, the
timer sees this. It must enable the EFPE bit now. Otherwise, it
decrements the verify_limit counter and tries again. Eventually it
moves the status to FAILED, from which the IRQ cannot move it anywhere
else, except for another stmmac_fpe_apply() call.
====================
Co-developed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/151f86c8428eba967039718c6bf90a7d841e703b.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By moving the fpe_cfg field to the stmmac_priv data, stmmac_fpe_cfg
becomes platform-data eventually, instead of a run-time config.
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://patch.msgid.link/d9b3d7ecb308c5e39778a4c8ae9df288a2754379.1725631883.git.0x1207@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
commit be27b89652 ("net: stmmac: replace priv->speed with
the portTransmitRate from the tc-cbs parameters") introduced
a problem. When deleting, it prompts "Invalid portTransmitRate
0 (idleSlope - sendSlope)" and exits. Add judgment on cbs.enable.
Only when offload is enabled, speed divider needs to be calculated.
Fixes: be27b89652 ("net: stmmac: replace priv->speed with the portTransmitRate from the tc-cbs parameters")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240617013922.1035854-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current cbs parameter depends on speed after uplinking,
which is not needed and will report a configuration error
if the port is not initially connected. The UAPI exposed by
tc-cbs requires userspace to recalculate the send slope anyway,
because the formula depends on port_transmit_rate (see man tc-cbs),
which is not an invariant from tc's perspective. Therefore, we
use offload->sendslope and offload->idleslope to derive the
original port_transmit_rate from the CBS formula.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240608143524.2065736-1-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the EST structure to struct stmmac_priv, because the
EST configs don't look like platform config, but EST is
enabled in runtime with the settings retrieved for the TC
TAPRIO feature also in runtime. So it's better to have the
EST-data preserved in the driver private data instead of
the platform data storage.
Signed-off-by: Xiaolei Wang <xiaolei.wang@windriver.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20240513014346.1718740-3-xiaolei.wang@windriver.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Report taprio offload status. This includes per txq and global
counters of window_drops and tx_overruns.
Window_drops count include count of frames dropped because of
queueMaxSDU setting and HLBF error. Transmission overrun counter
inform the user application whether any packets are currently being
transmitted on a particular queue during a gate-close event.DWMAC IPs
takes care Transmission overrun won't happen hence this is always 0.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring queueMaxSDU. As DWMAC IPs doesn't support
queueMaxSDU table handle this in the SW. The maximum 802.3 frame size
that is allowed to be transmitted by any queue is queueMaxSDU +
16 bytes (i.e. 6 bytes SA + 6 bytes DA + 4 bytes FCS).
Inspired from intel i225 driver.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cycle-time-extension. TER GCL-register needs to be
updated with the cycle-time-extension. Width of TER register is EST
time interval width + 7 bits.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-4-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor EST implementation by moving common code for DWMAC4 and
DWXGMAC IPs into a separate EST module. EST implementation for DWMAC4
and DWXGMAC differs only for CSR base address, PTOV field offset
width, and PTOV clock multiplier value.
Thanks, Serge Semin and Jakub Kicinski for the suggestions on
refactoring EST implementation into a separate EST module.
Signed-off-by: Rohan G Thomas <rohan.g.thomas@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231201055252.1302-3-rohan.g.thomas@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The status bits of register MAC_FPE_CTRL_STS are clear on read. Using
32-bit read for MAC_FPE_CTRL_STS in dwmac5_fpe_configure() and
dwmac5_fpe_send_mpacket() clear the status bits. Then the stmmac interrupt
handler missing FPE event status and leads to FPE handshaking failure and
retries.
To avoid clear status bits of MAC_FPE_CTRL_STS in dwmac5_fpe_configure()
and dwmac5_fpe_send_mpacket(), add fpe_csr to stmmac_fpe_cfg structure to
cache the control bits of MAC_FPE_CTRL_STS and to avoid reading
MAC_FPE_CTRL_STS in those methods.
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking procedure")
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jianheng Zhang <Jianheng.Zhang@synopsys.com>
Link: https://lore.kernel.org/r/CY5PR12MB637225A7CF529D5BE0FBE59CBF81A@CY5PR12MB6372.namprd12.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Inspired from struct flow_cls_offload :: cmd, in order for taprio to be
able to report statistics (which is future work), it seems that we need
to drill one step further with the ndo_setup_tc(TC_SETUP_QDISC_TAPRIO)
multiplexing, and pass the command as part of the common portion of the
muxed structure.
Since we already have an "enable" variable in tc_taprio_qopt_offload,
refactor all drivers to check for "cmd" instead of "enable", and reject
every other command except "replace" and "destroy" - to be future proof.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com> # for lan966x
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 classes of in-tree drivers currently:
- those who act upon struct tc_taprio_sched_entry :: gate_mask as if it
holds a bit mask of TXQs
- those who act upon the gate_mask as if it holds a bit mask of TCs
When it comes to the standard, IEEE 802.1Q-2018 does say this in the
second paragraph of section 8.6.8.4 Enhancements for scheduled traffic:
| A gate control list associated with each Port contains an ordered list
| of gate operations. Each gate operation changes the transmission gate
| state for the gate associated with each of the Port's traffic class
| queues and allows associated control operations to be scheduled.
In typically obtuse language, it refers to a "traffic class queue"
rather than a "traffic class" or a "queue". But careful reading of
802.1Q clarifies that "traffic class" and "queue" are in fact
synonymous (see 8.6.6 Queuing frames):
| A queue in this context is not necessarily a single FIFO data structure.
| A queue is a record of all frames of a given traffic class awaiting
| transmission on a given Bridge Port. The structure of this record is not
| specified.
i.o.w. their definition of "queue" isn't the Linux TX queue.
The gate_mask really is input into taprio via its UAPI as a mask of
traffic classes, but taprio_sched_to_offload() converts it into a TXQ
mask.
The breakdown of drivers which handle TC_SETUP_QDISC_TAPRIO is:
- hellcreek, felix, sja1105: these are DSA switches, it's not even very
clear what TXQs correspond to, other than purely software constructs.
Only the mqprio configuration with 8 TCs and 1 TXQ per TC makes sense.
So it's fine to convert these to a gate mask per TC.
- enetc: I have the hardware and can confirm that the gate mask is per
TC, and affects all TXQs (BD rings) configured for that priority.
- igc: in igc_save_qbv_schedule(), the gate_mask is clearly interpreted
to be per-TXQ.
- tsnep: Gerhard Engleder clarifies that even though this hardware
supports at most 1 TXQ per TC, the TXQ indices may be different from
the TC values themselves, and it is the TXQ indices that matter to
this hardware. So keep it per-TXQ as well.
- stmmac: I have a GMAC datasheet, and in the EST section it does
specify that the gate events are per TXQ rather than per TC.
- lan966x: again, this is a switch, and while not a DSA one, the way in
which it implements lan966x_mqprio_add() - by only allowing num_tc ==
NUM_PRIO_QUEUES (8) - makes it clear to me that TXQs are a purely
software construct here as well. They seem to map 1:1 with TCs.
- am65_cpsw: from looking at am65_cpsw_est_set_sched_cmds(), I get the
impression that the fetch_allow variable is treated like a prio_mask.
This definitely sounds closer to a per-TC gate mask rather than a
per-TXQ one, and TI documentation does seem to recomment an identity
mapping between TCs and TXQs. However, Roger Quadros would like to do
some testing before making changes, so I'm leaving this driver to
operate as it did before, for now. Link with more details at the end.
Based on this breakdown, we have 5 drivers with a gate mask per TC and
4 with a gate mask per TXQ. So let's make the gate mask per TXQ the
opt-in and the gate mask per TC the default.
Benefit from the TC_QUERY_CAPS feature that Jakub suggested we add, and
query the device driver before calling the proper ndo_setup_tc(), and
figure out if it expects one or the other format.
Link: https://patchwork.kernel.org/project/netdevbpf/patch/20230202003621.2679603-15-vladimir.oltean@nxp.com/#25193204
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Siddharth Vadapalli <s-vadapalli@ti.com>
Cc: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a boundary check to prevent negative basetime input from user
while configuring taprio.
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move dma buf conf to dedicated struct. This in preparation for code
rework that will permit to allocate separate dma_conf without affecting
the priv struct.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To replicate the issue:-
1) Add 1 flower filter for VLAN Priority based frame steering:-
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0
$ tc filter add dev $IFDEVNAME parent ffff: protocol 802.1Q \
flower vlan_prio 0 hw_tc 0
2) Get the 'pref' id
$ tc filter show dev $IFDEVNAME ingress
3) Delete a specific tc flower record (say pref 49151)
$ tc filter del dev $IFDEVNAME parent ffff: pref 49151
From dmesg, we will observe kernel NULL pointer ooops
[ 197.170464] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 197.171367] #PF: supervisor read access in kernel mode
[ 197.171367] #PF: error_code(0x0000) - not-present page
[ 197.171367] PGD 0 P4D 0
[ 197.171367] Oops: 0000 [#1] PREEMPT SMP NOPTI
<snip>
[ 197.171367] RIP: 0010:tc_setup_cls+0x20b/0x4a0 [stmmac]
<snip>
[ 197.171367] Call Trace:
[ 197.171367] <TASK>
[ 197.171367] ? __stmmac_disable_all_queues+0xa8/0xe0 [stmmac]
[ 197.171367] stmmac_setup_tc_block_cb+0x70/0x110 [stmmac]
[ 197.171367] tc_setup_cb_destroy+0xb3/0x180
[ 197.171367] fl_hw_destroy_filter+0x94/0xc0 [cls_flower]
The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.
struct flow_rule *rule = flow_cls_offload_flow_rule(cls);
struct flow_dissector *dissector = rule->match.dissector;
So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.
v2:
- Clean up overly extensive backtrace and rewrite git message to better
explain the kernel NULL pointer issue.
Fixes: 0e039f5cf8 ("net: stmmac: add RX frame steering based on VLAN priority in tc flower")
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit fe28c53ed7 ("net: stmmac: fix taprio configuration when
base_time is in the past") allowed some base time values in the past,
but apparently not all, the base-time value of 0 (Jan 1st 1970) is still
explicitly denied by the driver.
Remove the bogus check.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of taprio offload is not enabled, the error handling path
causes a kernel crash due to kernel NULL pointer deference.
Fix this by adding check for NULL before attempt to access 'plat->est'
on the mutex_lock() call.
The following kernel panic is observed without this patch:
RIP: 0010:mutex_lock+0x10/0x20
Call Trace:
tc_setup_taprio+0x482/0x560 [stmmac]
kmem_cache_alloc_trace+0x13f/0x490
taprio_disable_offload.isra.0+0x9d/0x180 [sch_taprio]
taprio_destroy+0x6c/0x100 [sch_taprio]
qdisc_create+0x2e5/0x4f0
tc_modify_qdisc+0x126/0x740
rtnetlink_rcv_msg+0x12b/0x380
_raw_spin_lock_irqsave+0x19/0x40
_raw_spin_unlock_irqrestore+0x18/0x30
create_object+0x212/0x340
rtnl_calcit.isra.0+0x110/0x110
netlink_rcv_skb+0x50/0x100
netlink_unicast+0x191/0x230
netlink_sendmsg+0x243/0x470
sock_sendmsg+0x5e/0x60
____sys_sendmsg+0x20b/0x280
copy_msghdr_from_user+0x5c/0x90
__mod_memcg_state+0x87/0xf0
___sys_sendmsg+0x7c/0xc0
lru_cache_add+0x7f/0xa0
_raw_spin_unlock+0x16/0x30
wp_page_copy+0x449/0x890
handle_mm_fault+0x921/0xfc0
__sys_sendmsg+0x59/0xa0
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xa9
---[ end trace b1f19b24368a96aa ]---
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adjusting the ptp time, the Qbv base time may be the past time
of the new current time. dwmac5 hardware limited the base time cannot
be set as past time. This patch add a btr_reserve to store the base
time get from qopt, then calculate the base time and reset the Qbv
configuration after ptp time adjust.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the TAS basetime calculation function so that it can be
called by other functions.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The continue statement in the for-loop has no effect, remove it.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch, "net: stmmac: support FPE link partner hand-shaking
procedure", priv->plat->fpe_cfg wouldn`t be "devm_kzalloc"ed if
dma_cap->frpsel is 0 (Flexible Rx Parser is not supported in SoC) in
tc_init(). So, fpe_cfg will be remain as NULL and accessing it will cause
kernel panic.
To fix this, move the "devm_kzalloc"ing of priv->plat->fpe_cfg before
dma_cap->frpsel checking in tc_init(). Additionally, checking of
priv->dma_cap.fpesel is added before calling stmmac_fpe_link_state_handle()
as only FPE supported SoC is allowed to call the function.
Below is the kernel panic dump reported by Marek Szyprowski
<m.szyprowski@samsung.com>:
meson8b-dwmac ff3f0000.ethernet eth0: PHY [0.0:00] driver [RTL8211F Gigabit Ethernet] (irq=35)
meson8b-dwmac ff3f0000.ethernet eth0: No Safety Features support found
meson8b-dwmac ff3f0000.ethernet eth0: PTP not supported by HW
meson8b-dwmac ff3f0000.ethernet eth0: configuring for phy/rgmii link mode
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000001
Mem abort info:
...
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000044eb000
[0000000000000001] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in: dw_hdmi_i2s_audio dw_hdmi_cec meson_gxl realtek meson_gxbb_wdt snd_soc_meson_axg_sound_card dwmac_generic axg_audio meson_dw_hdmi crct10dif_ce snd_soc_meson_card_utils snd_soc_meson_axg_tdmout panfrost rc_odroid gpu_sched reset_meson_audio_arb meson_ir snd_soc_meson_g12a_tohdmitx snd_soc_meson_axg_frddr sclk_div clk_phase snd_soc_meson_codec_glue dwmac_meson8b snd_soc_meson_axg_fifo stmmac_platform meson_rng meson_drm stmmac rtc_meson_vrtc rng_core meson_canvas pwm_meson dw_hdmi mdio_mux_meson_g12a pcs_xpcs snd_soc_meson_axg_tdm_interface snd_soc_meson_axg_tdm_formatter nvmem_meson_efuse display_connector
CPU: 1 PID: 7 Comm: kworker/u8:0 Not tainted 5.12.0-rc4-next-20210325+
Hardware name: Hardkernel ODROID-C4 (DT)
Workqueue: events_power_efficient phylink_resolve
pstate: 20400009 (nzCv daif +PAN -UAO -TCO BTYPE=--)
pc : stmmac_mac_link_up+0x14c/0x348 [stmmac]
lr : stmmac_mac_link_up+0x284/0x348 [stmmac] ...
Call trace:
stmmac_mac_link_up+0x14c/0x348 [stmmac]
phylink_resolve+0x104/0x420
process_one_work+0x2a8/0x718
worker_thread+0x48/0x460
kthread+0x134/0x160
ret_from_fork+0x10/0x18
Code: b971ba60 350007c0 f958c260 f9402000 (39400401)
---[ end trace 0c9deb6c510228aa ]---
Fixes: 5a5586112b ("net: stmmac: support FPE link partner hand-shaking
procedure")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to discover whether remote station supports frame preemption,
local station sends verify mPacket and expects response mPacket in
return from the remote station.
So, we add the functions to send and handle event when verify mPacket
and response mPacket are exchanged between the networked stations.
The mechanism to handle different FPE states between local and remote
station (link partner) is implemented using workqueue which starts a
task each time there is some sign of verify & response mPacket exchange
as check in FPE IRQ event. The task retries couple of times to try to
spot the states that both stations are ready to enter FPE ON. This allows
different end points to enable FPE at different time and verify-response
mPacket can happen asynchronously. Ultimately, the task will only turn
FPE ON when local station have both exchange response in both directions.
Thanks to Voon Weifeng for implementing the core functions for detecting
FPE events and send mPacket and phylink related change.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Co-developed-by: Tan Tee Min <tee.min.tan@intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We extend tc flower to support configuration of VLAN priority-based RX
frame steering hardware offloading.
To map VLAN <PCP> to Traffic Class <TC>:
$ tc filter add dev <IFNAME> parent ffff: protocol 802.1Q flower \
vlan_prio <PCP> hw_tc <TC>
Note: <TC> < N whereby "tc qdisc ... num_tc N ..."
To delete all tc flower configurations:
$ tc qdisc delete dev <IFNAME> ingress
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tc_add_flow() and tc_del_flow() use hardware L3 & L4 filters
as offloading. The number of L3/L4 filters is read from L3L4FNUM field
from MAC_HW_Feature1 register and is used to alloc priv->tc_entries[].
For RX frame steering based on VLAN priority offloading, we use
MAC_RXQ_CTRL2 & MAC_RXQ_CTRL3 registers and all VLAN priority level
can be configured independent from L3 & L4 filters.
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link speed is not 100 Mbps, port transmit rate and speed divider
are set to 8 and 1000000 respectively. These values are incorrect for
CBS idleslope and sendslope HW values calculation if the link speed is
not 1 Gbps.
This patch adds switch statement to set the values of port transmit rate
and speed divider for 10 Gbps, 5 Gbps, 2.5 Gbps, 1 Gbps, and 100 Mbps.
Note that CBS is not supported at 10 Mbps.
Fixes: bc41a6689b ("net: stmmac: tc: Remove the speed dependency")
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Link: https://lore.kernel.org/r/1613655653-11755-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When disable CBS, mode_to_use parameter is not updated even the operation
mode of Tx Queue is changed to Data Centre Bridging (DCB). Therefore,
when tc_setup_cbs() function is called to re-enable CBS, the operation
mode of Tx Queue remains at DCB, which causing CBS fails to work.
This patch updates the value of mode_to_use parameter to MTL_QUEUE_DCB
after operation mode of Tx Queue is changed to DCB in stmmac_dma_qmode()
callback function.
Fixes: 1f705bc61a ("net: stmmac: Add support for CBS QDISC")
Suggested-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Song, Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Link: https://lore.kernel.org/r/1612447396-20351-1-git-send-email-yoong.siang.song@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Synopsys TSN MAC supports Qbv base times in the past, but only up to a
certain limit. As a result, a taprio qdisc configuration with a small
base time (for example when treating the base time as a simple phase
offset) is not applied by the hardware and silently ignored.
This was observed on an NXP i.MX8MPlus device, but likely affects all
TSN-variants of the MAC.
Fix the issue by making sure the base time is in the future, pushing it by
an integer amount of cycle times if needed. (a similar check is already
done in several other taprio implementations, see for example
drivers/net/ethernet/intel/igc/igc_tsn.c#L116 or
drivers/net/dsa/sja1105/sja1105_ptp.h#L39).
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210113131557.24651-2-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
flow_action_hw_stats_types_check() helper takes one of the
FLOW_ACTION_HW_STATS_*_BIT values as input. If we align
the arguments to the opening bracket of the helper there
is no way to call this helper and stay under 80 characters.
Remove the "types" part from the new flow_action helpers
and enum values.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce flow_action_basic_hw_stats_types_check() helper and use it
in drivers. That sanitizes the drivers which do not have support
for action HW stats types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for ETF scheduler using TBS feature which is available
in XGMAC and QoS IPs.
Changes from v2:
- Fix checkpatch issues (Jakub)
- Use the TBS bitfield
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ARCHs that don't support 64 bits division we need to use the
helpers.
Fixes: b60189e039 ("net: stmmac: Integrate EST with TAPRIO scheduler API")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for Frame Preemption using TAPRIO API. This works along
with EST feature and allows to select if preemptable traffic shall be
sent during specific queues opening time.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the EST code for XGMAC and QoS we can use it with the
TAPRIO scheduler. Integrate it into the main driver and use the API to
configure the EST feature.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc_flow_parsers is not used outside of the driver, so
make it static to avoid the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_tc.c:516:3: warning: symbol 'tc_flow_parsers' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
