In order to mask off the bits, we need to use the '~' operator to invert
all the bits of _MASK and clear them.
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241107063637.2122726-3-leyfoon.tan@starfivetech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The high address will display as 0 if the driver does not set the
reg_space[]. To fix this, read the high address registers and
update the reg_space[] accordingly.
Fixes: fbf68229ff ("net: stmmac: unify registers dumps methods")
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241021054625.1791965-1-leyfoon.tan@starfivetech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Currently reset state configuration of split header works fine for
non-tagged packets and we see no corruption in payload of any size
We need additional programming sequence with reset configuration to
handle VLAN tagged packets to avoid corruption in payload for packets
of size greater than 256 bytes.
Without this change ping application complains about corruption
in payload when the size of the VLAN packet exceeds 256 bytes.
With this change tagged and non-tagged packets of any size works fine
and there is no corruption seen.
Current configuration which has the issue for VLAN packet
----------------------------------------------------------
Split happens at the position at Layer 3 header
|MAC-DA|MAC-SA|Vlan Tag|Ether type|IP header|IP data|Rest of the payload|
2 bytes ^
|
With the fix we are making sure that the split happens now at
Layer 2 which is end of ethernet header and start of IP payload
Ip traffic split
-----------------
Bits which take care of this are SPLM and SPLOFST
SPLM = Split mode is set to Layer 2
SPLOFST = These bits indicate the value of offset from the beginning
of Length/Type field at which header split should take place when the
appropriate SPLM is selected. Reset value is 2bytes.
Un-tagged data (without VLAN)
|MAC-DA|MAC-SA|Ether type|IP header|IP data|Rest of the payload|
2bytes ^
|
Tagged data (with VLAN)
|MAC-DA|MAC-SA|VLAN Tag|Ether type|IP header|IP data|Rest of the payload|
2bytes ^
|
Non-IP traffic split such AV packet
------------------------------------
Bits which take care of this are
SAVE = Split AV Enable
SAVO = Split AV Offset, similar to SPLOFST but this is for AVTP
packets.
|Preamble|MAC-DA|MAC-SA|VLAN tag|Ether type|IEEE 1722 payload|CRC|
2bytes ^
|
Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241016234313.3992214-1-quic_abchauha@quicinc.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ATDS (Alternate Descriptor Size) is a part of the DMA Bus Mode configs
(together with PBL, ALL, EME, etc) of the DW GMAC controllers. Seeing
it's not changed at runtime but is activated as long as the IP-core
has it supported (at least due to the Type 2 Full Checksum Offload
Engine feature), move the respective parameter from the
stmmac_dma_ops::init() callback argument to the stmmac_dma_cfg
structure, which already have the rest of the DMA-related configs
defined.
Besides the being added in the next commit DW GMAC multi-channels
support will require to add the stmmac_dma_ops::init_chan() callback
and have the ATDS flag set/cleared for each channel in there. Having
the atds-flag in the stmmac_dma_cfg structure will make the parameter
accessible from stmmac_dma_ops::init_chan() callback too.
Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn>
Signed-off-by: Yinggang Gu <guyinggang@loongson.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some platforms have dwmac4 implementations that have a different
address space layout than the default, resulting in the need to define
their own DMA/MTL offsets.
Extend the functions to allow a platform driver to indicate what its
addresses are, overriding the defaults.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Passing stmmac_priv to some of the callbacks allows hwif implementations
to grab some data that platforms can customize. Adjust the callbacks
accordingly in preparation of such a platform customization.
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some old IPs do not provide the hardware feature register.
On these IPs, this register is read 0x00000000.
In old driver version, this feature was handled but a regression came
with the commit f10a6a3541 ("stmmac: rework get_hw_feature function").
Indeed, this commit removes the return value in dma->get_hw_feature().
This return value was used to indicate the validity of retrieved
information and used later on in stmmac_hw_init() to override
priv->plat data if this hardware feature were valid.
This patch restores the return code in ->get_hw_feature() in order
to indicate the hardware feature validity and override priv->plat
data only if this hardware feature is valid.
Fixes: f10a6a3541 ("stmmac: rework get_hw_feature function")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX FIFO overflows when the system is not able to process all received
packets and they start accumulating (first in the DMA queue in memory,
then in the FIFO). An interrupt is then raised for each overflowing packet
and handled in stmmac_interrupt(). This is counter-productive, since it
brings the system (or more likely, one CPU core) to its knees to process
the FIFO overflow interrupts.
stmmac_interrupt() handles overflow interrupts by writing the rx tail ptr
into the corresponding hardware register (according to the MAC spec, this
has the effect of restarting the MAC DMA). However, without freeing any rx
descriptors, the DMA stops right away, and another overflow interrupt is
raised as the FIFO overflows again. Since the DMA is already restarted at
the end of stmmac_rx_refill() after freeing descriptors, disabling FIFO
overflow interrupts and the corresponding handling code has no side effect,
and eliminates the interrupt storm when the RX FIFO overflows.
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20210506143312.20784-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DWMAC Core 5.20 onwards supports HW descriptor prefetching.
Additionally, it also depends on platform specific RTL configuration.
This capability could be enabled by setting DMA_Mode bit-19 (DCHE).
So, to enable this cability, platform must set plat->dma_cfg->dche = true
and the DWMAC core version must be 5.20 onwards. Else, this capability
wouldn`t be configured
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For interrupt mode INTM=0, TX/RX transfer complete will trigger signal
not only on sbd_perch_[tx|rx]_intr_o (Transmit/Receive Per Channel) but
also on the sbd_intr_o (Common).
As for multi-MSI implementation, setting interrupt mode INTM=1 is more
efficient as each TX intr and RX intr (TI/RI) will be handled by TX/RX ISR
without the need of calling the common MAC ISR.
Updated the TX/RX NORMAL interrupts status checking process as the
NIS status bit is not asserted for any RI/TI events for INTM=1.
Signed-off-by: Wong, Vee Khee <vee.khee.wong@intel.com>
Co-developed-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: Voon Weifeng <weifeng.voon@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross timestamping is supported on Integrated Ethernet Controller in
Intel SoC such as EHL and TGL with Always Running Timer.
The hardware cross-timestamp result is made available to
applications through the PTP_SYS_OFFSET_PRECISE ioctl which calls
stmmac_getcrosststamp().
Device time is stored in the MAC Auxiliary register. The 64-bit System
time (ART timestamp) is stored in registers that are only addressable
by using MDIO space.
Signed-off-by: Tan Tee Min <tee.min.tan@intel.com>
Co-developed-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extending the driver to support per-queue RX and TX coalesce settings in
order to support below commands:
To show per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --show-coalesce
To set per-queue coalesce setting:-
$ ethtool --per-queue <DEVNAME> queue_mask <MASK> --coalesce \
[rx-usecs N] [rx-frames M] [tx-usecs P] [tx-frames Q]
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.
Fixes: 48863ce594 ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds all the necessary HW hooks to support TBS feature in QoS cores.
Changes from v1:
- Remove unneeded LT shift as the IP already does this.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds the HW specific support for Frame Preemption on GMAC5+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for EST in GMAC5+ cores. This feature allows to offload
scheduling of queues opening time to the IP.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores support Layer 3 and Layer 4 filtering. Add the
corresponding callbacks in these cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The address width of the controller can be read from hardware feature
registers much like on XGMAC. Add support for parsing the ADDR64 field
so that the DMA mask can be set accordingly.
This avoids getting swiotlb involved for DMA on Tegra186 and later.
Also make sure that the upper 32 bits of the DMA address are written to
the DMA descriptors when enhanced addressing mode is used. Similarily,
for each channel, the upper 32 bits of the DMA descriptor ring's base
address also need to be programmed to make sure the correct memory can
be fetched when the DMA descriptor ring is located beyond the 32-bit
boundary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the ARP Offload feature in GMAC4 and GMAC5 cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for TX VLAN Offload using descriptors based features
available in GMAC4/5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for Source Address Insertion and Replacement in GMAC4
and GMAC5 cores. Two methods are supported: Descriptor based and
register based.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the support for VLAN HASH Filtering in GMAC4/5 cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. get hash table size in hw feature reigster, and add support
for taller hash table(128/256) in dwmac4.
2. only clear GMAC_PACKET_FILTER bits used in this function,
to avoid side effect to functions of other bits.
stmmac selftests output log with flow control on:
ethtool -t eth0
The test result is PASS
The test extra info:
1. MAC Loopback 0
2. PHY Loopback -95
3. MMC Counters 0
4. EEE -95
5. Hash Filter MC 0
6. Perfect Filter UC 0
7. MC Filter 0
8. UC Filter 0
9. Flow Control 0
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a993db88d1 ("net: stmmac: Enable support for > 32 Bits
addressing in XGMAC"), introduced support for > 32 bits addressing in
XGMAC but the conversion of descriptors to dma_addr_t was left out.
As some devices assing coherent memory in regions > 32 bits we need to
set lower and upper value of descriptors address when initializing DMA
channels.
Luckly, this was working for me because I was assigning CMA to < 4GB
address space for performance reasons.
Fixes: a993db88d1 ("net: stmmac: Enable support for > 32 Bits addressing in XGMAC")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for CBS reconfiguration using the TC application.
A new callback was added to TC ops struct and another one to DMA ops to
reconfigure the channel mode.
Tested in GMAC5.10.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is clearly a bug.
We need to set the DMA buffer size in the HW otherwise corruption can
occur when receiving packets.
This is probably not occuring because of small MTU values and because HW
has a default value internally (which currently is bigger than default
buffer size).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for Flexible PPS output (which is equivalent
to per_out output of PTP subsystem).
Tested using an oscilloscope and the following commands:
1) Start PTP4L:
# ptp4l -A -4 -H -m -i eth0 &
2) Set Flexible PPS frequency:
# echo <idx> <ts> <tns> <ps> <pns> > /sys/class/ptp/ptpX/period
Where, ts/tns is start time and ps/pns is period time, and ptpX is ptp
of eth0.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the GMAC version for choosing if we need to use
dma_init or dma_init_{rx/tx}_chan callback, lets uniformize this and
always use the dma_init_{rx/tx}_chan callbacks.
While at it, fix the use of dma_init_chan callback, which shall be
called for as many channels as the max of rx/tx channels.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables OSP (Operate on Second Packet) for GMAC4. The feature
allows DMA to fetch second descriptor while its still processing the
first one.
Running iperf, the performance gain is +/- 38%.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for U32 filter by using an HW only feature called
Flexible RX Parser. This allow us to match any given packet field with a
pattern and accept/reject or even route the packet to a specific DMA
channel.
Right now we only support acception or rejection of frame and we only
support simple rules. Though, the Parser has the flexibility of jumping to
specific rules as an if condition so complex rules can be established.
This is only supported in GMAC5.10+.
The following commands can be used to test this code:
1) Setup an ingress qdisk:
# tc qdisc add dev eth0 handle ffff: ingress
2) Setup a filter (e.g. filter by IP):
# tc filter add dev eth0 parent ffff: protocol ip u32 match ip \
src 192.168.0.3 skip_sw action drop
In every tests performed we always used the "skip_sw" flag to make sure
only the RX Parser was involved.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.
The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.
In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control must be disabled for AVB enabled queues and TX
AVB queues must be enabled by setting BIT(2) of TXQEN.
Correct this by passing the queue mode to DMA callbacks
and by checking in these functions wether we are in AVB
performing the necessary adjustments.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are using all the available fifo size in RQS and
TQS fields. This will not work correctly in multi-queues IP's
because total fifo size must be splitted to the enabled queues.
Correct this by computing the available fifo size per queue and
setting the right value in TQS and RQS fields.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions dwmac4_dma_init_rx_chan, dwmac4_dma_init_tx_chan and
dwmac4_dma_init_channel do not need to be in global scope, so them
static.
Cleans up sparse warnings:
"symbol 'dwmac4_dma_init_rx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_tx_chan' was not declared. Should it be static?"
"symbol 'dwmac4_dma_init_channel' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares the DMA initialization process for multiple queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rx watchdog configuration for all queues.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program the receive queue size based on the RX FIFO size and enable
hardware flow control for large FIFOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New version of this core encode the FIFO sizes in one of the feature
registers. Use these sizes as default, but still allow device tree to
override them for backwards compatibility.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver have two methods for registers dumps: via ethtool and
at init (if NETIF_MSG_HW is enabled).
It is better to keep only one method, ethtool, since the other was ugly.
This patch convert all dump_regs() function from "printing regs" to
"fill the reg_space used by ethtool".
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the hardware is synthesized with multiple queues, all queues are
disabled for default. This patch adds the rx queues configuration.
This patch was successfully tested in a Synopsys QoS Reference design.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently always sets the PBLx8/PBLx4 bit, which means that
the pbl values configured via the pbl/txpbl/rxpbl DT properties are
always multiplied by 8/4 in the hardware.
In order to allow the DT to configure lower pbl values, while at the
same time not changing behavior of any existing device trees using the
pbl/txpbl/rxpbl settings, add a property to disable the multiplication
of the pbl by 8/4 in the hardware.
Suggested-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC and newer supports independent programmable burst lengths for
DMA tx/rx. Add new optional devicetree properties representing this.
To be backwards compatible, snps,pbl will still be valid, but
snps,txpbl/snps,rxpbl will override the value in snps,pbl if set.
If the IP is synthesized to use the AXI interface, there is a register
and a matching DT property inside the optional stmmac-axi-config DT node
for controlling burst lengths, named snps,blen.
However, using this register, it is not possible to control tx and rx
independently. Also, this register is not available if the IP was
synthesized with, e.g., the AHB interface.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct stmmac_dma_cfg *dma_cfg as an argument rather
than using all the struct members as individual arguments.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
