Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Remove unused functions.
These functions may have some value in documenting the
hardware. But that information may be accessed via SCM history.
Flagged by clang-16 with W=1.
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang with W=1 reports
drivers/net/ethernet/micrel/ksz884x.c:3216:6: error: variable
'change' set but not used [-Werror,-Wunused-but-set-variable]
int change = 0;
^
This variable is not used so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230329125929.1808420-1-trix@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_disable_device() need be called while module exiting, switch to use
pcim_enable(), pci_disable_device() will be called in pcim_release()
while unbinding device.
Fixes: 8ca86fd83e ("net: Micrel KSZ8841/2 PCI Ethernet driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221024131338.2848959-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some micrel devices share the same PHY register defines. This patch
moves them to one common header so other drivers can reuse them.
And reuse generic MII_* defines where possible.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/micrel/ksz884x.c:2163: warning: expecting prototype for sw_get_board_storm(). Prototype was for sw_get_broad_storm() instead
drivers/net/ethernet/micrel/ksz884x.c:2985: warning: expecting prototype for port_w_phy(). Prototype was for hw_w_phy() instead
drivers/net/ethernet/micrel/ksz884x.c:4792: warning: expecting prototype for transmit_done(). Prototype was for tx_done() instead
Cc: Tristram Ha <Tristram.Ha@micrel.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/micrel/ksz884x.c: In function rx_proc:
drivers/net/ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/micrel/ksz884x.c: In function netdev_get_ethtool_stats:
drivers/net/ethernet/micrel/ksz884x.c:6512:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
these variable is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <apais@linux.microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain configurations without power management support, gcc report
the following warning:
drivers/net/ethernet/micrel/ksz884x.c:7182:12: warning:
'pcidev_suspend' defined but not used [-Wunused-function]
7182 | static int pcidev_suspend(struct device *dev_d)
| ^~~~~~~~~~~~~~
Mark pcidev_suspend() as __maybe_unused to make it clear.
Fixes: 64120615d1 ("ksz884x: use generic power management")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With legacy PM, drivers themselves were responsible for managing the
device's power states and takes care of register states.
After upgrading to the generic structure, PCI core will take care of
required tasks and drivers should do only device-specific operations.
Thus, there is no need to call the PCI helper functions like
pci_enable_wake(), pci_save/restore_sate() and
pci_set_power_state().
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial cleanup, so that all bridge port-specific code can be found in
one go.
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer 'info' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'info' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix typos and add the following to the scripts/spelling.txt:
overrided||overridden
Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use time_is_before_eq_jiffies macro for time comparison
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use the time_after_eq macro for jiffies comparison operation
Signed-off-by: Antonio Murdaca <antonio.murdaca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.function = f;
-t.data = d;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the function port_cfg_dis_learn() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To be future-proof and for better readability the time comparisons are modified
to use time_before_eq() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This unifies the behaviour with other network device drivers and
allows for a matching of the PCI device path in UDEV rules.
Signed-off-by: Markus Lottmann <markus.lottmann1986@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in copy_old_skb that can
be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise. In this code, it is the variable result that is used for
the return code, not rc.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This macro is used to create a struct pci_device_id array.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
