This patch implements the CN20k MBOX communication between AF and
AF's VFs. This implementation uses separate trigger interrupts
for request, response messages against using trigger message data in CN10K.
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1749639716-13868-6-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This implementation uses separate trigger interrupts for request,
response messages against using trigger message data in CN10K.
This patch adds support for basic mbox implementation for CN20K
from NIC PF side.
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1749639716-13868-5-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR (net-6.15-rc8).
Conflicts:
80f2ab46c2 ("irdma: free iwdev->rf after removing MSI-X")
4bcc063939 ("ice, irdma: fix an off by one in error handling code")
c24a65b6a2 ("iidc/ice/irdma: Update IDC to support multiple consumers")
https://lore.kernel.org/20250513130630.280ee6c5@canb.auug.org.au
No extra adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Priority flow control is not supported for LBK and SDP vf. This patch
adds support to not add dcbnl_ops for LBK and SDP vf.
Fixes: 8e67558177 ("octeontx2-pf: PFC config support with DCBx")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250519072658.2960851-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch adds pcifunc which represents PF and VF device to the
tracepoints otx2_msg_alloc, otx2_msg_send, otx2_msg_process so that
it is easier to correlate which device allocated the message, which
device forwarded it and which device processed that message.
Also add message id in otx2_msg_send tracepoint to check which
message is sent at any point of time from a device.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://patch.msgid.link/1747136408-30685-4-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The currently used function pci_request_regions() is one of the
problematic "hybrid devres" PCI functions, which are sometimes managed
through devres, and sometimes not (depending on whether
pci_enable_device() or pcim_enable_device() has been called before).
The PCI subsystem wants to remove this behavior and, therefore, needs to
port all users to functions that don't have this problem.
Furthermore, the PCI function being managed implies that it's not
necessary to call pci_release_regions() manually.
Remove the calls to pci_release_regions().
Replace pci_request_regions() with pcim_request_all_regions().
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Link: https://patch.msgid.link/20250425085740.65304-4-phasta@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A previous patch introduces a build-time warning when CONFIG_DCB
is disabled:
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c: In function 'otx2_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c:3217:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c: In function 'otx2vf_probe':
drivers/net/ethernet/marvell/octeontx2/nic/otx2_vf.c:740:1: error: label 'err_free_zc_bmap' defined but not used [-Werror=unused-label]
Add the same #ifdef check around it.
Fixes: efabce2901 ("octeontx2-pf: AF_XDP zero copy receive support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Link: https://patch.msgid.link/20250219162239.1376865-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds support to AF_XDP zero copy for CN10K.
This patch specifically adds receive side support. In this approach once
a xdp program with zero copy support on a specific rx queue is enabled,
then that receive quse is disabled/detached from the existing kernel
queue and re-assigned to the umem memory.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
One crypto hardware logical function (cpt-lf) per netdev is
required for outbound ipsec crypto offload. Allocate, attach
and initialize one crypto hardware function when enabling
outbound ipsec crypto offload. Crypto hardware function will
be detached and freed on disabling outbound ipsec crypto
offload.
Signed-off-by: Bharat Bhushan <bbhushan2@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports different types of MACs eg RPM, SDP, LBK.
LBK is for internal Tx->Rx HW loopback path. RPM and SDP MACs support
ingress/egress pkt IO on interfaces with different set of capabilities
like interface modes. At the time of netdev driver registration PF will
seek MAC related information from Admin function driver
'drivers/net/ethernet/marvell/octeontx2/af' and sets up ingress/egress
queues etc such that pkt IO on the channels of these different MACs is
possible. This patch add representors for SDP MAC.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements basic set of net_device_ops.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mbox, hw resources and interrupt configuration functions to common
header file. So, that they can be used later by the RVU representor driver.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241023161843.15543-5-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reuse the maximum support HW MTU value that is fetch during probe.
Instead of fetching through mbox each time mtu is changed as the
value is fixed for interface.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241023161843.15543-4-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During VF driver remove, a message is sent to detach VF
resources to PF but VF is not waiting until message is
complete. Also mailbox interrupts need to be turned off
after the detach resource message is complete. This patch
fixes that problem.
Fixes: 05fcc9e089 ("octeontx2-pf: Attach NIX and NPA block LFs")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Core
----
- Rework the sendpage & splice implementations. Instead of feeding
data into sockets page by page extend sendmsg handlers to support
taking a reference on the data, controlled by a new flag called
MSG_SPLICE_PAGES. Rework the handling of unexpected-end-of-file
to invoke an additional callback instead of trying to predict what
the right combination of MORE/NOTLAST flags is.
Remove the MSG_SENDPAGE_NOTLAST flag completely.
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid.
- Enable socket busy polling with CONFIG_RT.
- Improve reliability and efficiency of reporting for ref_tracker.
- Auto-generate a user space C library for various Netlink families.
Protocols
---------
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2].
- Use per-VMA locking for "page-flipping" TCP receive zerocopy.
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags.
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative.
- Create a new MPTCP getsockopt to retrieve all info (MPTCP_FULL_INFO).
- Avoid waking up applications using TLS sockets until we have
a full record.
- Allow using kernel memory for protocol ioctl callbacks, paving
the way to issuing ioctls over io_uring.
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address.
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch.
- PPPoE: make number of hash bits configurable.
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig).
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge).
- Support matching on Connectivity Fault Management (CFM) packets.
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug.
- HSR: don't enable promiscuous mode if device offloads the proto.
- Support active scanning in IEEE 802.15.4.
- Continue work on Multi-Link Operation for WiFi 7.
BPF
---
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used,
or in fact passing the verifier at all for complex programs,
especially those using open-coded iterators.
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what
the output buffer *should* be, without writing anything.
- Accept dynptr memory as memory arguments passed to helpers.
- Add routing table ID to bpf_fib_lookup BPF helper.
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands.
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only).
- Show target_{obj,btf}_id in tracing link fdinfo.
- Addition of several new kfuncs (most of the names are self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter
---------
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value.
- Increase ip_vs_conn_tab_bits range for 64BIT builds.
- Allow updating size of a set.
- Improve NAT tuple selection when connection is closing.
Driver API
----------
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out).
- Support configuring rate selection pins of SFP modules.
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines.
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer.
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio).
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message.
- Split devlink instance and devlink port operations.
New hardware / drivers
----------------------
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers
-------
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is
a variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split
the different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and
Enhanced MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9i4I
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking changes from Jakub Kicinski:
"WiFi 7 and sendpage changes are the biggest pieces of work for this
release. The latter will definitely require fixes but I think that we
got it to a reasonable point.
Core:
- Rework the sendpage & splice implementations
Instead of feeding data into sockets page by page extend sendmsg
handlers to support taking a reference on the data, controlled by a
new flag called MSG_SPLICE_PAGES
Rework the handling of unexpected-end-of-file to invoke an
additional callback instead of trying to predict what the right
combination of MORE/NOTLAST flags is
Remove the MSG_SENDPAGE_NOTLAST flag completely
- Implement SCM_PIDFD, a new type of CMSG type analogous to
SCM_CREDENTIALS, but it contains pidfd instead of plain pid
- Enable socket busy polling with CONFIG_RT
- Improve reliability and efficiency of reporting for ref_tracker
- Auto-generate a user space C library for various Netlink families
Protocols:
- Allow TCP to shrink the advertised window when necessary, prevent
sk_rcvbuf auto-tuning from growing the window all the way up to
tcp_rmem[2]
- Use per-VMA locking for "page-flipping" TCP receive zerocopy
- Prepare TCP for device-to-device data transfers, by making sure
that payloads are always attached to skbs as page frags
- Make the backoff time for the first N TCP SYN retransmissions
linear. Exponential backoff is unnecessarily conservative
- Create a new MPTCP getsockopt to retrieve all info
(MPTCP_FULL_INFO)
- Avoid waking up applications using TLS sockets until we have a full
record
- Allow using kernel memory for protocol ioctl callbacks, paving the
way to issuing ioctls over io_uring
- Add nolocalbypass option to VxLAN, forcing packets to be fully
encapsulated even if they are destined for a local IP address
- Make TCPv4 use consistent hash in TIME_WAIT and SYN_RECV. Ensure
in-kernel ECMP implementation (e.g. Open vSwitch) select the same
link for all packets. Support L4 symmetric hashing in Open vSwitch
- PPPoE: make number of hash bits configurable
- Allow DNS to be overwritten by DHCPACK in the in-kernel DHCP client
(ipconfig)
- Add layer 2 miss indication and filtering, allowing higher layers
(e.g. ACL filters) to make forwarding decisions based on whether
packet matched forwarding state in lower devices (bridge)
- Support matching on Connectivity Fault Management (CFM) packets
- Hide the "link becomes ready" IPv6 messages by demoting their
printk level to debug
- HSR: don't enable promiscuous mode if device offloads the proto
- Support active scanning in IEEE 802.15.4
- Continue work on Multi-Link Operation for WiFi 7
BPF:
- Add precision propagation for subprogs and callbacks. This allows
maintaining verification efficiency when subprograms are used, or
in fact passing the verifier at all for complex programs,
especially those using open-coded iterators
- Improve BPF's {g,s}setsockopt() length handling. Previously BPF
assumed the length is always equal to the amount of written data.
But some protos allow passing a NULL buffer to discover what the
output buffer *should* be, without writing anything
- Accept dynptr memory as memory arguments passed to helpers
- Add routing table ID to bpf_fib_lookup BPF helper
- Support O_PATH FDs in BPF_OBJ_PIN and BPF_OBJ_GET commands
- Drop bpf_capable() check in BPF_MAP_FREEZE command (used to mark
maps as read-only)
- Show target_{obj,btf}_id in tracing link fdinfo
- Addition of several new kfuncs (most of the names are
self-explanatory):
- Add a set of new dynptr kfuncs: bpf_dynptr_adjust(),
bpf_dynptr_is_null(), bpf_dynptr_is_rdonly(), bpf_dynptr_size()
and bpf_dynptr_clone().
- bpf_task_under_cgroup()
- bpf_sock_destroy() - force closing sockets
- bpf_cpumask_first_and(), rework bpf_cpumask_any*() kfuncs
Netfilter:
- Relax set/map validation checks in nf_tables. Allow checking
presence of an entry in a map without using the value
- Increase ip_vs_conn_tab_bits range for 64BIT builds
- Allow updating size of a set
- Improve NAT tuple selection when connection is closing
Driver API:
- Integrate netdev with LED subsystem, to allow configuring HW
"offloaded" blinking of LEDs based on link state and activity
(i.e. packets coming in and out)
- Support configuring rate selection pins of SFP modules
- Factor Clause 73 auto-negotiation code out of the drivers, provide
common helper routines
- Add more fool-proof helpers for managing lifetime of MDIO devices
associated with the PCS layer
- Allow drivers to report advanced statistics related to Time Aware
scheduler offload (taprio)
- Allow opting out of VF statistics in link dump, to allow more VFs
to fit into the message
- Split devlink instance and devlink port operations
New hardware / drivers:
- Ethernet:
- Synopsys EMAC4 IP support (stmmac)
- Marvell 88E6361 8 port (5x1GE + 3x2.5GE) switches
- Marvell 88E6250 7 port switches
- Microchip LAN8650/1 Rev.B0 PHYs
- MediaTek MT7981/MT7988 built-in 1GE PHY driver
- WiFi:
- Realtek RTL8192FU, 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps
- Realtek RTL8723DS (SDIO variant)
- Realtek RTL8851BE
- CAN:
- Fintek F81604
Drivers:
- Ethernet NICs:
- Intel (100G, ice):
- support dynamic interrupt allocation
- use meta data match instead of VF MAC addr on slow-path
- nVidia/Mellanox:
- extend link aggregation to handle 4, rather than just 2 ports
- spawn sub-functions without any features by default
- OcteonTX2:
- support HTB (Tx scheduling/QoS) offload
- make RSS hash generation configurable
- support selecting Rx queue using TC filters
- Wangxun (ngbe/txgbe):
- add basic Tx/Rx packet offloads
- add phylink support (SFP/PCS control)
- Freescale/NXP (enetc):
- report TAPRIO packet statistics
- Solarflare/AMD:
- support matching on IP ToS and UDP source port of outer
header
- VxLAN and GENEVE tunnel encapsulation over IPv4 or IPv6
- add devlink dev info support for EF10
- Virtual NICs:
- Microsoft vNIC:
- size the Rx indirection table based on requested
configuration
- support VLAN tagging
- Amazon vNIC:
- try to reuse Rx buffers if not fully consumed, useful for ARM
servers running with 16kB pages
- Google vNIC:
- support TCP segmentation of >64kB frames
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- enable USXGMII (88E6191X)
- Microchip:
- lan966x: add support for Egress Stage 0 ACL engine
- lan966x: support mapping packet priority to internal switch
priority (based on PCP or DSCP)
- Ethernet PHYs:
- Broadcom PHYs:
- support for Wake-on-LAN for BCM54210E/B50212E
- report LPI counter
- Microsemi PHYs: support RGMII delay configuration (VSC85xx)
- Micrel PHYs: receive timestamp in the frame (LAN8841)
- Realtek PHYs: support optional external PHY clock
- Altera TSE PCS: merge the driver into Lynx PCS which it is a
variant of
- CAN: Kvaser PCIEcan:
- support packet timestamping
- WiFi:
- Intel (iwlwifi):
- major update for new firmware and Multi-Link Operation (MLO)
- configuration rework to drop test devices and split the
different families
- support for segmented PNVM images and power tables
- new vendor entries for PPAG (platform antenna gain) feature
- Qualcomm 802.11ax (ath11k):
- Multiple Basic Service Set Identifier (MBSSID) and Enhanced
MBSSID Advertisement (EMA) support in AP mode
- support factory test mode
- RealTek (rtw89):
- add RSSI based antenna diversity
- support U-NII-4 channels on 5 GHz band
- RealTek (rtl8xxxu):
- AP mode support for 8188f
- support USB RX aggregation for the newer chips"
* tag 'net-next-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1602 commits)
net: scm: introduce and use scm_recv_unix helper
af_unix: Skip SCM_PIDFD if scm->pid is NULL.
net: lan743x: Simplify comparison
netlink: Add __sock_i_ino() for __netlink_diag_dump().
net: dsa: avoid suspicious RCU usage for synced VLAN-aware MAC addresses
Revert "af_unix: Call scm_recv() only after scm_set_cred()."
phylink: ReST-ify the phylink_pcs_neg_mode() kdoc
libceph: Partially revert changes to support MSG_SPLICE_PAGES
net: phy: mscc: fix packet loss due to RGMII delays
net: mana: use vmalloc_array and vcalloc
net: enetc: use vmalloc_array and vcalloc
ionic: use vmalloc_array and vcalloc
pds_core: use vmalloc_array and vcalloc
gve: use vmalloc_array and vcalloc
octeon_ep: use vmalloc_array and vcalloc
net: usb: qmi_wwan: add u-blox 0x1312 composition
perf trace: fix MSG_SPLICE_PAGES build error
ipvlan: Fix return value of ipvlan_queue_xmit()
netfilter: nf_tables: fix underflow in chain reference counter
netfilter: nf_tables: unbind non-anonymous set if rule construction fails
...
This patch registers callbacks to support HTB offload.
Below are features supported,
- supports traffic shaping on the given class by honoring rate and ceil
configuration.
- supports traffic scheduling, which prioritizes different types of
traffic based on strict priority values.
- supports the creation of leaf to inner classes such that parent node
rate limits apply to all child nodes.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Upon txschq free request, the transmit schedular config in hardware
is not getting reset. This patch adds necessary changes to do the same.
2. Current implementation calls txschq alloc during interface
initialization and in response handler updates the default txschq array.
This creates a problem for htb offload where txsch alloc will be called
for every tc class. This patch addresses the issue by reading txschq
response in mbox caller function instead in the response handler.
3. Current otx2_txschq_stop routine tries to free all txschq nodes
allocated to the interface. This creates a problem for htb offload.
This patch introduces the otx2_txschq_free_one to free txschq in a
given level.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation is such that the number of Send queues (SQs)
are decided on the device probe which is equal to the number of online
cpus. These SQs are allocated and deallocated in interface open and c
lose calls respectively.
This patch defines new APIs for initializing and deinitializing Send
queues dynamically and allocates more number of transmit queues for
QOS feature.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
current implementation is such that tot_tx_queues contains both
xdp queues and normal tx queues. which will be allocated in interface
open calls and deallocated on interface down calls respectively.
With addition of QOS, where send quees are allocated/deallacated upon
user request Qos send queues won't be part of tot_tx_queues. So this
patch renames tot_tx_queues to non_qos_queues.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BACKGROUND
==========
When multiple work items are queued to a workqueue, their execution order
doesn't match the queueing order. They may get executed in any order and
simultaneously. When fully serialized execution - one by one in the queueing
order - is needed, an ordered workqueue should be used which can be created
with alloc_ordered_workqueue().
However, alloc_ordered_workqueue() was a later addition. Before it, an
ordered workqueue could be obtained by creating an UNBOUND workqueue with
@max_active==1. This originally was an implementation side-effect which was
broken by 4c16bd327c ("workqueue: restore WQ_UNBOUND/max_active==1 to be
ordered"). Because there were users that depended on the ordered execution,
5c0338c687 ("workqueue: restore WQ_UNBOUND/max_active==1 to be ordered")
made workqueue allocation path to implicitly promote UNBOUND workqueues w/
@max_active==1 to ordered workqueues.
While this has worked okay, overloading the UNBOUND allocation interface
this way creates other issues. It's difficult to tell whether a given
workqueue actually needs to be ordered and users that legitimately want a
min concurrency level wq unexpectedly gets an ordered one instead. With
planned UNBOUND workqueue updates to improve execution locality and more
prevalence of chiplet designs which can benefit from such improvements, this
isn't a state we wanna be in forever.
This patch series audits all callsites that create an UNBOUND workqueue w/
@max_active==1 and converts them to alloc_ordered_workqueue() as necessary.
WHAT TO LOOK FOR
================
The conversions are from
alloc_workqueue(WQ_UNBOUND | flags, 1, args..)
to
alloc_ordered_workqueue(flags, args...)
which don't cause any functional changes. If you know that fully ordered
execution is not ncessary, please let me know. I'll drop the conversion and
instead add a comment noting the fact to reduce confusion while conversion
is in progress.
If you aren't fully sure, it's completely fine to let the conversion
through. The behavior will stay exactly the same and we can always
reconsider later.
As there are follow-up workqueue core changes, I'd really appreciate if the
patch can be routed through the workqueue tree w/ your acks. Thanks.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Sunil Goutham <sgoutham@marvell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ratheesh Kannoth <rkannoth@marvell.com>
Cc: Srujana Challa <schalla@marvell.com>
Cc: Geetha sowjanya <gakula@marvell.com>
Cc: netdev@vger.kernel.org
When a VF device probe fails due to error in MSIX vector allocation then
the resources NIX and NPA LFs were not detached. Fix this by detaching
the LFs when MSIX vector allocation fails.
Fixes: 3184fb5ba9 ("octeontx2-vf: Virtual function driver support")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the free_percpu for the allocated "vf->hw.lmt_info" in order to avoid
memory leak, same as the "pf->hw.lmt_info" in
`drivers/net/ethernet/marvell/octeontx2/nic/otx2_pf.c`.
Fixes: 5c0512072f ("octeontx2-pf: cn10k: Use runtime allocated LMTLINE region")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Link: https://lore.kernel.org/r/20230317064337.18198-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
resources allocated like mcam entries to support the Ntuple feature
and hash tables for the tc feature are not getting freed in driver
unbind. This patch fixes the issue.
Fixes: 2da4894327 ("octeontx2-pf: devlink params support to set mcam entry count")
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20230109061325.21395-1-hkelam@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Drivers should call the TSO setting helper, GSO is controllable
by user space.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion Queue Entry(CQE) is a descriptor written
by hardware to notify software about the send and
receive completion status. The CQE can be of size
128 or 512 bytes. A 512 bytes CQE can hold more receive
fragments pointers compared to 128 bytes CQE. This
patch enables to modify CQE size using:
<ethtool -G cqe-size N>.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds TC feature for VFs also. When MCAM
rules are allocated for a VF then either TC or ntuple
filters can be used. Below are the commands to use
TC feature for a VF(say lbk0):
devlink dev param set pci/0002:01:00.1 name mcam_count value 16 \
cmode runtime
ethtool -K lbk0 hw-tc-offload on
ifconfig lbk0 up
tc qdisc add dev lbk0 ingress
tc filter add dev lbk0 parent ffff: protocol ip flower skip_sw \
dst_mac 98:03:9b:83:aa:12 action police rate 100Mbit burst 5000
Also to modify any fields of the hardware context with
NIX_AQ_INSTOP_WRITE command then corresponding masks of those
fields must be set as per hardware. This was missing in
ingress ratelimiting context. This patch sets those masks also.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Data centric bridging designed to eliminate packet loss due to
queue overflow by adding enhancements to ethernet network such as
proprity flow control etc. This patch adds support for management
of Priority flow control(PFC) on Octeontx2 and CN10K interfaces.
To enable PFC for all priorities
dcb pfc set dev eth0 prio-pfc all:on/off
To enable PFC on selected priorites
dcb pfc set dev eth0 prio-pfc 0:on/off 1:on/off ..7:on/off
With the ntuple commands user can map Priority to receive queues.
On queue overflow NIX will assert backpressure such that PFC pause frames
are genarated with mapped priority.
To map priority 7 to Queue 1
ethtool -U eth0 flow-type ether dst xx:xx:xx:xx:xx:xx vlan 0xe00a
m 0x1fff queue 1
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation is such that 802.3x pause frames are
enabled by default. As CGX and RPM blocks support PFC
(priority flow control) also, instead of driver enabling one
between them enable them upon request from PF or its VFs.
Also add support to disable pause frames in driver unbind.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool rx-buf-len is for setting receive buffer size,
support setting it via ethtool -G parameter and getting
it via ethtool -g parameter.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF is removed respective PTP resources are not
being freed currently. This patch fixes it.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mii ioctls are now handled by the ndo_eth_ioctl() callback,
not the old ndo_do_ioctl(), but octeontx2-nicvf introduced the
function for the old way.
Move it over to ndo_eth_ioctl() to actually allow calling it from
user space.
Fixes: 43510ef4dd ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Fixes: a76053707d ("dev_ioctl: split out ndo_eth_ioctl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> #mlx*
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds XDP_PASS, XDP_TX, XDP_DROP and XDP_REDIRECT support
for netdev PF.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PTP PHC support to NIX VF interfaces. This enables
a VF to run PTP master/slave instance. PTP block being a shared
hardware resource it is recommended to avoid running multiple
PTP instances in the system which will impact the PTP clock
accuracy.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the netdev
drivers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added support for setting or modifying MCAM entry count at
runtime via devlink params.
commands:
devlink dev param show
pci/0002:02:00.0:
name mcam_count type driver-specific
values:
cmode runtime value 16
devlink dev param set pci/0002:02:00.0 name mcam_count
value 64 cmode runtime
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add packet flow classification support for both LMAC mapped virtual
functions and loopback VFs. This patch adds supports for ntuple
offload feature.
Signed-off-by: Rakesh Babu <rsaladi2@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabled NETIF_F_RXALL support for VF driver.
Also removed MTU range comments which are no longer valid.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver uses static LMTST region allocated by firmware.
This memory gets populated as PF/VF BAR2. RVU PF/VF driver ioremap
the memory as device memory for NIX/NPA operation. Since the memory
is mapped as device memory we see performance degration. To address
this issue this patch implements runtime memory allocation.
RVU PF/VF allocates memory during device probe and share the base
address with RVU AF. RVU AF then configure the LMT MAP table
accordingly.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_rx_mode callback handler to configure promisc, multicast and
allmulti options for VF driver. Also, modified PF driver ndo_set_rx_mode
handler to support multicast and promisc mode independently.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <Sunil.Goutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K supports max MTU of 16K on LMAC links and 64k on LBK
links and Octeontx2 silicon supports 9K mtu on both links.
Get the same from nix_get_hw_info mbox message in netdev probe.
This patch also calculates receive buffer size required based
on the MTU set.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to use new LMTST lines for NPA batch free
and burst SQE flush. Adds new dev_hw_ops structure to hold platform
specific functions and create new files cn10k.c and cn10k.h.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CN10K platform transmit/receive buffer alloc and free from/to hardware
had changed to support burst operation. Whereas pervious silicon's only
support single buffer free at a time.
To Support the same firmware allocates a DRAM region for each PF/VF for
storing LMTLINES. These LMTLINES are used for NPA batch free and for
flushing SQE to the hardware.
PF/VF LMTST region is accessed via BAR4. PFs LMTST region is followed
by its VFs mbox memory. The size of region varies from 2KB to 256KB based
on number of LMTLINES configured.
This patch adds support for
- Mapping PF/VF LMTST region.
- Reserves 0-71 (RX + TX + XDP) LMTST lines for NPA batch
free operation.
- Reserves 72-512 LMTST lines for NIX SQE flush.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware allocates memory regions for PFs and VFs in DRAM.
The PFs memory region is used for AF-PF and PF-VF mailbox.
This mbox facilitate communication between AF-PF and PF-VF.
On CN10K platform:
The DRAM region allocated to PF is enumerated as PF BAR4 memory.
PF BAR4 contains AF-PF mbox region followed by its VFs mbox region.
AF-PF mbox region base address is configured at RVU_AF_PFX_BAR4_ADDR
PF-VF mailbox base address is configured at
RVU_PF(x)_VF_MBOX_ADDR = RVU_AF_PF()_BAR4_ADDR+64KB. PF access its
mbox region via BAR4, whereas VF accesses PF-VF DRAM mailboxes via
BAR2 indirect access.
On CN9XX platform:
Mailbox region in DRAM is divided into two parts AF-PF mbox region and
PF-VF mbox region i.e all PFs mbox region is contiguous similarly all
VFs.
The base address of the AF-PF mbox region is configured at
RVU_AF_PF_BAR4_ADDR.
AF-PF1 mbox address can be calculated as RVU_AF_PF_BAR4_ADDR * mbox
size.
The base address of PF-VF mbox region for each PF is configure at
RVU_AF_PF(0..15)_VF_BAR4_ADDR.PF access its mbox region via BAR4 and its
VF mbox regions from RVU_PF_VF_BAR4_ADDR register, whereas VF access its
mbox region via BAR4.
This patch changes mbox initialization to support both CN9XX and CN10K
platform.
The patch also adds new hw_cap flag to setting hw features like TSO etc
and removes platform specific name from the PF/VF driver name to make it
appropriate for all supported platforms
This patch also removes platform specific name from the PF/VF driver name
to make it appropriate for all supported platforms
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements egress VLAN offload by appending NIX_SEND_EXT_S
header to NIX_SEND_HDR_S. The VLAN TCI information is specified
in the NIX_SEND_EXT_S. The VLAN offload in the ingress path is
implemented by configuring the NIX_RX_VTAG_ACTION_S to strip and
capture the outer vlan fields. The NIX PF allocates one MCAM entry
for Rx VLAN offload.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
