Fix typos in comments and error messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250723201528.2908218-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On Aspeed SoCs, the internal MAC reset is insufficient to fully reset the
RMII interface; only the SoC-level reset line can properly reset the RMII
logic. This patch adds support for an optional "resets" property in the
device tree, allowing the driver to assert and deassert the SoC reset line
when operating in RMII mode. This ensures the MAC and RMII interface are
correctly reset and initialized.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709070809.2560688-5-jacky_chou@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending on e.g. DT configuration this driver uses a fixed link.
So we shouldn't rely on the user to enable FIXED_PHY, select it in
Kconfig instead. We may end up with a non-functional driver otherwise.
Fixes: 38561ded50 ("net: ftgmac100: support fixed link")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/476bb33b-5584-40f0-826a-7294980f2895@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All callers pass PHY_POLL, therefore remove irq argument from
fixed_phy_register().
Note: I keep the irq argument in fixed_phy_add_gpiod() for now,
for the case that somebody may want to use a GPIO interrupt in
the future, by e.g. adding a call to fwnode_irq_get() to
fixed_phy_get_gpiod().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/31cdb232-a5e9-4997-a285-cb9a7d208124@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Consolidate the handling of dedicated PHY and fixed-link phy by taking
advantage of logic in of_phy_get_and_connect() which handles both of
these cases, rather than open coding the same logic in ftgmac100_probe().
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241022084214.1261174-1-jacky_chou@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In NC-SI specification, NC-SI is using RMII, not MII.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <20241018053331.1900100-1-jacky_chou@aspeedtech.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Add error handling from calling fixed_phy_register.
It may return some error, therefore, need to check the status.
And fixed_phy_register needs to bind a device node for mdio.
Add the mac device node for fixed_phy_register function.
This is a reference to this function, of_phy_register_fixed_link().
Fixes: e24a6c8746 ("net: ftgmac100: Get link speed and duplex for NC-SI")
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Link: https://patch.msgid.link/20241007032435.787892-1-jacky_chou@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Cross-merge networking fixes after downstream PR.
No conflicts (sort of) and no adjacent changes.
This merge reverts commit b3c9e65eb2 ("net: hsr: remove seqnr_lock")
from net, as it was superseded by
commit 430d67bdcb ("net: hsr: Use the seqnr lock for frames received via interlink port.")
in net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the driver only enables RX interrupt to handle RX
packets and TX resources. Sometimes there is not RX traffic,
so the TX resource needs to wait for RX interrupt to free.
This situation will toggle the TX timeout watchdog when the MAC
TX ring has no more resources to transmit packets.
Therefore, enable TX interrupt to release TX resources at any time.
When I am verifying iperf3 over UDP, the network hangs.
Like the log below.
root# iperf3 -c 192.168.100.100 -i1 -t10 -u -b0
Connecting to host 192.168.100.100, port 5201
[ 4] local 192.168.100.101 port 35773 connected to 192.168.100.100 port 5201
[ ID] Interval Transfer Bandwidth Total Datagrams
[ 4] 0.00-20.42 sec 160 KBytes 64.2 Kbits/sec 20
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
[ 4] 20.42-20.42 sec 0.00 Bytes 0.00 bits/sec 0
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bandwidth Jitter Lost/Total Datagrams
[ 4] 0.00-20.42 sec 160 KBytes 64.2 Kbits/sec 0.000 ms 0/20 (0%)
[ 4] Sent 20 datagrams
iperf3: error - the server has terminated
The network topology is FTGMAC connects directly to a PC.
UDP does not need to wait for ACK, unlike TCP.
Therefore, FTGMAC needs to enable TX interrupt to release TX resources instead
of waiting for the RX interrupt.
Fixes: 10cbd64076 ("ftgmac100: Rework NAPI & interrupts handling")
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Link: https://patch.msgid.link/20240906062831.2243399-1-jacky_chou@aspeedtech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ethtool of this driver uses the phy API of ethtool
to get the link information from PHY driver.
Because the NC-SI is forced on 100Mbps and full duplex,
the driver connect a fixed-link phy driver for NC-SI.
The ethtool will get the link information from the
fixed-link phy driver.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20240827030513.481469-1-jacky_chou@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver must ensure TX descriptor updates are visible
before updating TX pointer and TX clear pointer.
This resolves TX hangs observed on AST2600 when running
iperf3.
Signed-off-by: Jacky Chou <jacky_chou@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert these drivers from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netdev_mc_count() is not zero and not IFF_ALLMULTI, filter
incoming multicast packets. The chip has a Multicast Address Hash Table
for allowed multicast addresses, so we fill it.
Implement .ndo_set_rx_mode and recalculate multicast hash table. Also
observe change of IFF_PROMISC and IFF_ALLMULTI netdev flags.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of of_get_ethdev_address() to support reading MAC address not
only from the usual DT nodes but also from an NVMEM provider (e.g. using
a dedicated area in an FRU EEPROM).
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20230713095743.30517-1-fercerpav@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When netdev->flags has IFF_PROMISC or IFF_ALLMULTI, set the
corresponding bits in the MAC Control Register (MACCR).
This change is based on code from the ftgmac100 driver, see
ftgmac100_start_hw() in ftgmac100.c
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the FTMAC100 is used as a DSA master, then it is expected that frames
which are MTU sized on the wire facing the external switch port (1500
octets in L2 payload, plus L2 header) also get a DSA tag when seen by
the host port.
This extra tag increases the length of the packet as the host port sees
it, and the FTMAC100 is not prepared to handle frames whose length
exceeds 1518 octets (including FCS) at all.
Only a minimal rework is needed to support this configuration. Since
MTU-sized DSA-tagged frames still fit within a single buffer (RX_BUF_SIZE),
we just need to optimize the resource management rather than implement
multi buffer RX.
In ndo_change_mtu(), we toggle the FTMAC100_MACCR_RX_FTL bit to tell the
hardware to drop (or not) frames with an L2 payload length larger than
1500. We need to replicate the MACCR configuration in ftmac100_start_hw()
as well, since there is a hardware reset there which clears previous
settings.
The advantage of dynamically changing FTMAC100_MACCR_RX_FTL is that when
dev->mtu is at the default value of 1500, large frames are automatically
dropped in hardware and we do not spend CPU cycles dropping them.
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-3-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver uses the MAX_PKT_SIZE (1518) for both MTU reporting and for
TX. However, the 2 places do not measure the same thing.
On TX, skb->len measures the entire L2 packet length (without FCS, which
software does not possess). So the comparison against 1518 there is
correct.
What is not correct is the reporting of dev->max_mtu as 1518. Since MTU
measures L2 *payload* length (excluding L2 overhead) and not total L2
packet length, it means that the correct max_mtu supported by this
device is the standard 1500. Anything higher than that will be dropped
on RX currently.
To fix this, subtract VLAN_ETH_HLEN from MAX_PKT_SIZE when reporting the
max_mtu, since that is the difference between L2 payload length and
total L2 length as seen by software.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-2-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eliminate one check in the data path and move it elsewhere, to where our
real limitation is. We'll want to start processing "too long" frames in
the driver (currently there is a hardware MAC setting which drops
theses).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20221028183220.155948-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Support fixed link in ftgmac100 driver. Fixed link is used on several
Meta OpenBMC platforms, such as Elbert (AST2620) and Wedge400 (AST2520).
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Sparse found a number of endianness-related issues of these kinds:
.../ftmac100.c:192:32: warning: restricted __le32 degrades to integer
.../ftmac100.c:208:23: warning: incorrect type in assignment (different base types)
.../ftmac100.c:208:23: expected unsigned int rxdes0
.../ftmac100.c:208:23: got restricted __le32 [usertype]
.../ftmac100.c:249:23: warning: invalid assignment: &=
.../ftmac100.c:249:23: left side has type unsigned int
.../ftmac100.c:249:23: right side has type restricted __le32
.../ftmac100.c:527:16: warning: cast to restricted __le32
Change type of some fields from 'unsigned int' to '__le32' to fix it.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220902113749.1408562-1-saproj@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver always generated a random ethernet address. Leave it as a
fallback solution, but add a call to platform_get_ethdev_address().
Handle EPROBE_DEFER returned from platform_get_ethdev_address() to
retry when EEPROM is ready.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220824151724.2698107-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In case ftmac100 is used with a DSA switch, Linux wants to set MTU
to 1504 to accommodate for DSA overhead. With the default max_mtu
it leads to the error message:
ftmac100 92000000.mac eth0: error -22 setting MTU to 1504 to include DSA overhead
ftmac100 supports packet length 1518 (MAX_PKT_SIZE constant), so it is
safe to report it in max_mtu.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220821160844.474277-1-saproj@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In ftgmac100_probe(), we should hold the refernece returned by
of_get_child_by_name() and use it to call of_node_put() for
reference balance.
Fixes: 39bfab8844 ("net: ftgmac100: Add support for DT phy-handle property")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AST2600 when using the i210 NIC over NC-SI has been observed to
produce incorrect checksum results with specific MTU values. This was
first observed when sending data across a long distance set of networks.
On a local network, the following test was performed using a 1MB file of
random data.
On the receiver run this script:
#!/bin/bash
while [ 1 ]; do
# Zero the stats
nstat -r > /dev/null
nc -l 9899 > test-file
# Check for checksum errors
TcpInCsumErrors=$(nstat | grep TcpInCsumErrors)
if [ -z "$TcpInCsumErrors" ]; then
echo No TcpInCsumErrors
else
echo TcpInCsumErrors = $TcpInCsumErrors
fi
done
On an AST2600 system:
# nc <IP of receiver host> 9899 < test-file
The test was repeated with various MTU values:
# ip link set mtu 1410 dev eth0
The observed results:
1500 - good
1434 - bad
1400 - good
1410 - bad
1420 - good
The test was repeated after disabling tx checksumming:
# ethtool -K eth0 tx-checksumming off
And all MTU values tested resulted in transfers without error.
An issue with the driver cannot be ruled out, however there has been no
bug discovered so far.
David has done the work to take the original bug report of slow data
transfer between long distance connections and triaged it down to this
test case.
The vendor suspects this this is a hardware issue when using NC-SI. The
fixes line refers to the patch that introduced AST2600 support.
Reported-by: David Wilder <wilder@us.ibm.com>
Reviewed-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
AST2600 MAC register 0x58 is writable only when the MAC clock is
enabled. Usually, the MAC clock is enabled by the bootloader so
register 0x58 is set normally when the bootloader is involved. To make
ast2600 ftgmac100 work without the bootloader, postpone the register
write until the clock is ready.
Fixes: 137d23cea1 ("net: ftgmac100: Fix Aspeed ast2600 TX hang issue")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good. This
was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly
tricky and error-prone code.
There is a small merge conflict against a parisc cleanup, the
solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel. The
hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
There are some obvious conflicts against changes to the removed
files.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks.
-----BEGIN PGP SIGNATURE-----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=vtCN
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
The nds32 architecture, also known as AndeStar V3, is a custom 32-bit
RISC target designed by Andes Technologies. Support was added to the
kernel in 2016 as the replacement RISC-V based V5 processors were
already announced, and maintained by (current or former) Andes
employees.
As explained by Alan Kao, new customers are now all using RISC-V,
and all known nds32 users are already on longterm stable kernels
provided by Andes, with no development work going into mainline
support any more.
While the port is still in a reasonably good shape, it only gets
worse over time without active maintainers, so it seems best
to remove it before it becomes unusable. As always, if it turns
out that there are mainline users after all, and they volunteer
to maintain the port in the future, the removal can be reverted.
Link: https://lore.kernel.org/linux-mm/YhdWNLUhk+x9RAzU@yamatobi.andestech.com/
Link: https://lore.kernel.org/lkml/20220302065213.82702-1-alankao@andestech.com/
Link: https://www.andestech.com/en/products-solutions/andestar-architecture/
Signed-off-by: Alan Kao <alankao@andestech.com>
[arnd: rewrite changelog to provide more background]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DHCP failures were observed with systemd 247.6. The issue could be
reproduced by rebooting Aspeed 2600 and then running ifconfig ethX
down/up.
It is caused by below procedures in the driver:
1. ftgmac100_open() enables net interface and call phy_start()
2. When PHY is link up, it calls netif_carrier_on() and then
adjust_link callback
3. ftgmac100_adjust_link() will schedule the reset task
4. ftgmac100_reset_task() will then reset the MAC in another schedule
After step 2, systemd will be notified to send DHCP discover packet,
while the packet might be corrupted by MAC reset operation in step 4.
Call ftgmac100_reset() directly instead of scheduling task to fix the
issue.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare for ftgmac100_adjust_link() to call
ftgmac100_reset() directly. Only code places are changed.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to prepare for ftgmac100_adjust_link() to call reset function
directly, instead of task schedule.
Signed-off-by: Heyi Guo <guoheyi@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a few drivers to device_get_ethdev_address(),
saving a few LoC.
The check if addr is valid in netsec is superfluous,
device_get_ethdev_addr() already checks that (in
fwnode_get_mac_addr()).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers pass in ETH_ALEN and the function itself
will return -EINVAL for any other address length.
Just assume it's ETH_ALEN like all other mac address
helpers (nvm, of, platform).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fwnode_get_mac_address() and device_get_mac_address()
return a pointer to the buffer that was passed to them
on success or NULL on failure. None of the callers
care about the actual value, only if it's NULL or not.
These semantics differ from of_get_mac_address() which
returns an int so to avoid confusion make the device
helpers return an errno.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():
@@
expression dev, np;
@@
- ether_addr_copy(dev->dev_addr, np)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variables will be free on path err_phy_connect, it should
return error code, or it will cause double free when calling
ftgmac100_remove().
Fixes: bd466c3fb5 ("net/faraday: Support NCSI mode")
Fixes: 39bfab8844 ("net: ftgmac100: Add support for DT phy-handle property")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt handler may set the flag to reset the mac in the future,
but that flag is not cleared once the reset has occurred.
Fixes: 10cbd64076 ("ftgmac100: Rework NAPI & interrupts handling")
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A number of ethernet drivers require crc32 functionality to be
avaialable in the kernel, causing a link error otherwise:
arm-linux-gnueabi-ld: drivers/net/ethernet/agere/et131x.o: in function `et1310_setup_device_for_multicast':
et131x.c:(.text+0x5918): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/cadence/macb_main.o: in function `macb_start_xmit':
macb_main.c:(.text+0x4b88): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/faraday/ftgmac100.o: in function `ftgmac100_set_rx_mode':
ftgmac100.c:(.text+0x2b38): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fec_main.o: in function `set_multicast_list':
fec_main.c:(.text+0x6120): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o: in function `dtsec_add_hash_mac_address':
fman_dtsec.c:(.text+0x830): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/freescale/fman/fman_dtsec.o:fman_dtsec.c:(.text+0xb68): more undefined references to `crc32_le' follow
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_hwinfo.o: in function `nfp_hwinfo_read':
nfp_hwinfo.c:(.text+0x250): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_hwinfo.c:(.text+0x288): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/netronome/nfp/nfpcore/nfp_resource.o: in function `nfp_resource_acquire':
nfp_resource.c:(.text+0x144): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: nfp_resource.c:(.text+0x158): undefined reference to `crc32_be'
arm-linux-gnueabi-ld: drivers/net/ethernet/nxp/lpc_eth.o: in function `lpc_eth_set_multicast_list':
lpc_eth.c:(.text+0x1934): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_do':
rocker_ofdpa.c:(.text+0x2e08): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_flow_tbl_del':
rocker_ofdpa.c:(.text+0x3074): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/rocker/rocker_ofdpa.o: in function `ofdpa_port_fdb':
arm-linux-gnueabi-ld: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.o: in function `mlx5dr_ste_calc_hash_index':
dr_ste.c:(.text+0x354): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_netdev_set_multicast':
lan743x_main.c:(.text+0x5dc4): undefined reference to `crc32_le'
Add the missing 'select CRC32' entries in Kconfig for each of them.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Acked-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Link: https://lore.kernel.org/r/20201203232114.1485603-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When removing the driver we would hit BUG_ON(!list_empty(&dev->ptype_specific))
in net/core/dev.c due to still having the NC-SI packet handler
registered.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
------------[ cut here ]------------
kernel BUG at net/core/dev.c:10254!
Internal error: Oops - BUG: 0 [#1] SMP ARM
CPU: 0 PID: 115 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00007-g02e0365710c4 #46
Hardware name: Generic DT based system
PC is at netdev_run_todo+0x314/0x394
LR is at cpumask_next+0x20/0x24
pc : [<806f5830>] lr : [<80863cb0>] psr: 80000153
sp : 855bbd58 ip : 00000001 fp : 855bbdac
r10: 80c03d00 r9 : 80c06228 r8 : 81158c54
r7 : 00000000 r6 : 80c05dec r5 : 80c05d18 r4 : 813b9280
r3 : 813b9054 r2 : 8122c470 r1 : 00000002 r0 : 00000002
Flags: Nzcv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85514008 DAC: 00000051
Process sh (pid: 115, stack limit = 0x7cb5703d)
...
Backtrace:
[<806f551c>] (netdev_run_todo) from [<80707eec>] (rtnl_unlock+0x18/0x1c)
r10:00000051 r9:854ed710 r8:81158c54 r7:80c76bb0 r6:81158c10 r5:8115b410
r4:813b9000
[<80707ed4>] (rtnl_unlock) from [<806f5db8>] (unregister_netdev+0x2c/0x30)
[<806f5d8c>] (unregister_netdev) from [<805a8180>] (ftgmac100_remove+0x20/0xa8)
r5:8115b410 r4:813b9000
[<805a8160>] (ftgmac100_remove) from [<805355e4>] (platform_drv_remove+0x34/0x4c)
Fixes: bd466c3fb5 ("net/faraday: Support NCSI mode")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201117024448.1170761-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
