It is desireable to push the hardware accelerator to also
process non-segmented TCP frames: we pass the skb->len
to the "TOE/TSO" offloader and it will handle them.
Without this quirk the driver becomes unstable and lock
up and and crash.
I do not know exactly why, but it is probably due to the
TOE (TCP offload engine) feature that is coupled with the
segmentation feature - it is not possible to turn one
part off and not the other, either both TOE and TSO are
active, or neither of them.
Not having the TOE part active seems detrimental, as if
that hardware feature is not really supposed to be turned
off.
The datasheet says:
"Based on packet parsing and TCP connection/NAT table
lookup results, the NetEngine puts the packets
belonging to the same TCP connection to the same queue
for the software to process. The NetEngine puts
incoming packets to the buffer or series of buffers
for a jumbo packet. With this hardware acceleration,
IP/TCP header parsing, checksum validation and
connection lookup are offloaded from the software
processing."
After numerous tests with the hardware locking up after
something between minutes and hours depending on load
using iperf3 I have concluded this is necessary to stabilize
the hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patch.msgid.link/20250408-gemini-ethernet-tso-always-v1-1-e669f932359c@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Core & protocols
----------------
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls).
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked)
in BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream performance
up to 2x.
- Improve performance of contended connect() by 200% by searching
for an available 4-tuple under RCU rather than a spin lock.
Bring an additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles.
There are up to 4 namespace roles but we used to have just 2 netns
pointer arguments, interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout
in TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar
to normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name
to messages as metadata
Driver API
----------
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where possible.
Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers
--------------
- Remove the IBM LCS driver for s390.
- Remove the sb1000 cable modem driver.
- Add support for SFP module access over SMBus.
- Add MCTP transport driver for MCTP-over-USB.
- Enable XDP metadata support in multiple drivers.
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96% with
1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XY0S
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Continue Netlink conversions to per-namespace RTNL lock
(IPv4 routing, routing rules, routing next hops, ARP ioctls)
- Continue extending the use of netdev instance locks. As a driver
opt-in protect queue operations and (in due course) ethtool
operations with the instance lock and not RTNL lock.
- Support collecting TCP timestamps (data submitted, sent, acked) in
BPF, allowing for transparent (to the application) and lower
overhead tracking of TCP RPC performance.
- Tweak existing networking Rx zero-copy infra to support zero-copy
Rx via io_uring.
- Optimize MPTCP performance in single subflow mode by 29%.
- Enable GRO on packets which went thru XDP CPU redirect (were queued
for processing on a different CPU). Improving TCP stream
performance up to 2x.
- Improve performance of contended connect() by 200% by searching for
an available 4-tuple under RCU rather than a spin lock. Bring an
additional 229% improvement by tweaking hash distribution.
- Avoid unconditionally touching sk_tsflags on RX, improving
performance under UDP flood by as much as 10%.
- Avoid skb_clone() dance in ping_rcv() to improve performance under
ping flood.
- Avoid FIB lookup in netfilter if socket is available, 20% perf win.
- Rework network device creation (in-kernel) API to more clearly
identify network namespaces and their roles. There are up to 4
namespace roles but we used to have just 2 netns pointer arguments,
interpreted differently based on context.
- Use sysfs_break_active_protection() instead of trylock to avoid
deadlocks between unregistering objects and sysfs access.
- Add a new sysctl and sockopt for capping max retransmit timeout in
TCP.
- Support masking port and DSCP in routing rule matches.
- Support dumping IPv4 multicast addresses with RTM_GETMULTICAST.
- Support specifying at what time packet should be sent on AF_XDP
sockets.
- Expose TCP ULP diagnostic info (for TLS and MPTCP) to non-admin
users.
- Add Netlink YAML spec for WiFi (nl80211) and conntrack.
- Introduce EXPORT_IPV6_MOD() and EXPORT_IPV6_MOD_GPL() for symbols
which only need to be exported when IPv6 support is built as a
module.
- Age FDB entries based on Rx not Tx traffic in VxLAN, similar to
normal bridging.
- Allow users to specify source port range for GENEVE tunnels.
- netconsole: allow attaching kernel release, CPU ID and task name to
messages as metadata
Driver API:
- Continue rework / fixing of Energy Efficient Ethernet (EEE) across
the SW layers. Delegate the responsibilities to phylink where
possible. Improve its handling in phylib.
- Support symmetric OR-XOR RSS hashing algorithm.
- Support tracking and preserving IRQ affinity by NAPI itself.
- Support loopback mode speed selection for interface selftests.
Device drivers:
- Remove the IBM LCS driver for s390
- Remove the sb1000 cable modem driver
- Add support for SFP module access over SMBus
- Add MCTP transport driver for MCTP-over-USB
- Enable XDP metadata support in multiple drivers
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- add PCIe TLP Processing Hints (TPH) support for new AMD
platforms
- support dumping RoCE queue state for debug
- opt into instance locking
- Intel (100G, ice, idpf):
- ice: rework MSI-X IRQ management and distribution
- ice: support for E830 devices
- iavf: add support for Rx timestamping
- iavf: opt into instance locking
- nVidia/Mellanox:
- mlx4: use page pool memory allocator for Rx
- mlx5: support for one PTP device per hardware clock
- mlx5: support for 200Gbps per-lane link modes
- mlx5: move IPSec policy check after decryption
- AMD/Solarflare:
- support FW flashing via devlink
- Cisco (enic):
- use page pool memory allocator for Rx
- enable 32, 64 byte CQEs
- get max rx/tx ring size from the device
- Meta (fbnic):
- support flow steering and RSS configuration
- report queue stats
- support TCP segmentation
- support IRQ coalescing
- support ring size configuration
- Marvell/Cavium:
- support AF_XDP
- Wangxun:
- support for PTP clock and timestamping
- Huawei (hibmcge):
- checksum offload
- add more statistics
- Ethernet virtual:
- VirtIO net:
- aggressively suppress Tx completions, improve perf by 96%
with 1 CPU and 55% with 2 CPUs
- expose NAPI to IRQ mapping and persist NAPI settings
- Google (gve):
- support XDP in DQO RDA Queue Format
- opt into instance locking
- Microsoft vNIC:
- support BIG TCP
- Ethernet NICs consumer, and embedded:
- Synopsys (stmmac):
- cleanup Tx and Tx clock setting and other link-focused
cleanups
- enable SGMII and 2500BASEX mode switching for Intel platforms
- support Sophgo SG2044
- Broadcom switches (b53):
- support for BCM53101
- TI:
- iep: add perout configuration support
- icssg: support XDP
- Cadence (macb):
- implement BQL
- Xilinx (axinet):
- support dynamic IRQ moderation and changing coalescing at
runtime
- implement BQL
- report standard stats
- MediaTek:
- support phylink managed EEE
- Intel:
- igc: don't restart the interface on every XDP program change
- RealTek (r8169):
- support reading registers of internal PHYs directly
- increase max jumbo packet size on RTL8125/RTL8126
- Airoha:
- support for RISC-V NPU packet processing unit
- enable scatter-gather and support MTU up to 9kB
- Tehuti (tn40xx):
- support cards with TN4010 MAC and an Aquantia AQR105 PHY
- Ethernet PHYs:
- support for TJA1102S, TJA1121
- dp83tg720: add randomized polling intervals for link detection
- dp83822: support changing the transmit amplitude voltage
- support for LEDs on 88q2xxx
- CAN:
- canxl: support Remote Request Substitution bit access
- flexcan: add S32G2/S32G3 SoC
- WiFi:
- remove cooked monitor support
- strict mode for better AP testing
- basic EPCS support
- OMI RX bandwidth reduction support
- batman-adv: add support for jumbo frames
- WiFi drivers:
- RealTek (rtw88):
- support RTL8814AE and RTL8814AU
- RealTek (rtw89):
- switch using wiphy_lock and wiphy_work
- add BB context to manipulate two PHY as preparation of MLO
- improve BT-coexistence mechanism to play A2DP smoothly
- Intel (iwlwifi):
- add new iwlmld sub-driver for latest HW/FW combinations
- MediaTek (mt76):
- preparation for mt7996 Multi-Link Operation (MLO) support
- Qualcomm/Atheros (ath12k):
- continued work on MLO
- Silabs (wfx):
- Wake-on-WLAN support
- Bluetooth:
- add support for skb TX SND/COMPLETION timestamping
- hci_core: enable buffer flow control for SCO/eSCO
- coredump: log devcd dumps into the monitor
- Bluetooth drivers:
- intel: add support to configure TX power
- nxp: handle bootloader error during cmd5 and cmd7"
* tag 'net-next-6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1681 commits)
unix: fix up for "apparmor: add fine grained af_unix mediation"
mctp: Fix incorrect tx flow invalidation condition in mctp-i2c
net: usb: asix: ax88772: Increase phy_name size
net: phy: Introduce PHY_ID_SIZE — minimum size for PHY ID string
net: libwx: fix Tx L4 checksum
net: libwx: fix Tx descriptor content for some tunnel packets
atm: Fix NULL pointer dereference
net: tn40xx: add pci-id of the aqr105-based Tehuti TN4010 cards
net: tn40xx: prepare tn40xx driver to find phy of the TN9510 card
net: tn40xx: create swnode for mdio and aqr105 phy and add to mdiobus
net: phy: aquantia: add essential functions to aqr105 driver
net: phy: aquantia: search for firmware-name in fwnode
net: phy: aquantia: add probe function to aqr105 for firmware loading
net: phy: Add swnode support to mdiobus_scan
gve: add XDP DROP and PASS support for DQ
gve: update XDP allocation path support RX buffer posting
gve: merge packet buffer size fields
gve: update GQ RX to use buf_size
gve: introduce config-based allocation for XDP
gve: remove xdp_xsk_done and xdp_xsk_wakeup statistics
...
In fact, these two are not tied closely to each other. The only
requirements to GRO are to use it in the BH context and have some
sane limits on the packet batches, e.g. NAPI has a limit of its
budget (64/8/etc.).
Move purely GRO fields into a new structure, &gro_node. Embed it
into &napi_struct and adjust all the references.
gro_node::cached_napi_id is effectively the same as
napi_struct::napi_id, but to be used on GRO hotpath to mark skbs.
napi_struct::napi_id is now a fully control path field.
Three Ethernet drivers use napi_gro_flush() not really meant to be
exported, so move it to <net/gro.h> and add that include there.
napi_gro_receive() is used in more than 100 drivers, keep it
in <linux/netdevice.h>.
This does not make GRO ready to use outside of the NAPI context
yet.
Tested-by: Daniel Xu <dxu@dxuuu.xyz>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
hrtimer_setup() takes the callback function pointer as argument and
initializes the timer completely.
Replace hrtimer_init() and the open coded initialization of
hrtimer::function with the new setup mechanism.
Patch was created by using Coccinelle.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/ddbeac1e5d81df33e9cccb099f520111cb8ce9c4.1738746872.git.namcao@linutronix.de
After commit 0edb555a65 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/net/ethernet to use
.remove(), with the eventual goal to drop struct
platform_driver::remove_new(). As .remove() and .remove_new() have the
same prototypes, conversion is done by just changing the structure
member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://patch.msgid.link/18f7c585a1a8a8ac8b03a2fca7de19bd5c52ac2b.1727949050.git.u.kleine-koenig@baylibre.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Cortina Gemini ethernet can very well set up TX or RX
pausing, so add this functionality to the driver in a
.set_pauseparam() callback. Essentially just call down to
phylib and let phylib deal with this, .adjust_link()
will respect the setting from phylib.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240529-gemini-phylib-fixes-v4-3-16487ca4c2fe@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Instead of directly poking into registers of the PHY, use
the existing function to query phylib about this directly.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240529-gemini-phylib-fixes-v4-2-16487ca4c2fe@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The callback passed to of_phy_get_and_connect() in the
Cortina Gemini driver is called "gmac_speed_set" which is
archaic, rename it to "gmac_adjust_link" following the
pattern of most other drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240529-gemini-phylib-fixes-v4-1-16487ca4c2fe@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
An earlier commit deleted the TSO support in the Cortina Gemini
driver because the driver was confusing gso_size and MTU,
probably because what the Linux kernel calls "gso_size" was
called "MTU" in the datasheet.
Restore the functionality properly reading the gso_size from
the skbuff.
Tested with iperf3, running a server on a different machine
and client on the device with the cortina gemini ethernet:
Connecting to host 192.168.1.2, port 5201
60008000.ethernet-port eth0: segment offloading mss = 05ea len=1c8a
60008000.ethernet-port eth0: segment offloading mss = 05ea len=1c8a
60008000.ethernet-port eth0: segment offloading mss = 05ea len=27da
60008000.ethernet-port eth0: segment offloading mss = 05ea len=0b92
60008000.ethernet-port eth0: segment offloading mss = 05ea len=2bda
(...)
(The hardware MSS 0x05ea here includes the ethernet headers.)
If I disable all segment offloading on the receiving host and
dump packets using tcpdump -xx like this:
ethtool -K enp2s0 gro off gso off tso off
tcpdump -xx -i enp2s0 host 192.168.1.136
I get segmented packages such as this when running iperf3:
23:16:54.024139 IP OpenWrt.lan.59168 > Fecusia.targus-getdata1:
Flags [.], seq 1486:2934, ack 1, win 4198,
options [nop,nop,TS val 3886192908 ecr 3601341877], length 1448
0x0000: fc34 9701 a0c6 14d6 4da8 3c4f 0800 4500
0x0010: 05dc 16a0 4000 4006 9aa1 c0a8 0188 c0a8
0x0020: 0102 e720 1451 ff25 9822 4c52 29cf 8010
0x0030: 1066 ac8c 0000 0101 080a e7a2 990c d6a8
(...)
0x05c0: 5e49 e109 fe8c 4617 5e18 7a82 7eae d647
0x05d0: e8ee ae64 dc88 c897 3f8a 07a4 3a33 6b1b
0x05e0: 3501 a30f 2758 cc44 4b4a
Several such packets often follow after each other verifying
the segmentation into 0x05a8 (1448) byte packages also on the
reveiving end. As can be seen, the ethernet frames are
0x05ea (1514) in size.
Performance with iperf3 before this patch: ~15.5 Mbit/s
Performance with iperf3 after this patch: ~175 Mbit/s
This was running a 60 second test (twice) the best measurement
was 179 Mbit/s.
For comparison if I run iperf3 with UDP I get around 1.05 Mbit/s
both before and after this patch.
While this is a gigabit ethernet interface, the CPU is a cheap
D-Link DIR-685 router (based on the ARMv5 Faraday FA526 at
~50 MHz), and the software is not supposed to drive traffic,
as the device has a DSA chip, so this kind of numbers can be
expected.
Fixes: ac631873c9 ("net: ethernet: cortina: Drop TSO support")
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a probably long standing problem in the Cortina
Gemini ethernet driver: there are some paths in the code
where the IRQ registers are written without taking the proper
locks.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240509-gemini-ethernet-locking-v1-1-afd00a528b95@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon reported that ndo_change_mtu() methods were never
updated to use WRITE_ONCE(dev->mtu, new_mtu) as hinted
in commit 501a90c945 ("inet: protect against too small
mtu values.")
We read dev->mtu without holding RTNL in many places,
with READ_ONCE() annotations.
It is time to take care of ndo_change_mtu() methods
to use corresponding WRITE_ONCE()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Simon Horman <horms@kernel.org>
Closes: https://lore.kernel.org/netdev/20240505144608.GB67882@kernel.org/
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <horms@kernel.org>
Acked-by: Shannon Nelson <shannon.nelson@amd.com>
Link: https://lore.kernel.org/r/20240506102812.3025432-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The recent change to allow large frames without hardware checksumming
slotted in software checksumming in the driver if hardware could not
do it.
This will however upset TSO (TCP Segment Offloading). Typical
error dumps includes this:
skb len=2961 headroom=222 headlen=66 tailroom=0
(...)
WARNING: CPU: 0 PID: 956 at net/core/dev.c:3259 skb_warn_bad_offload+0x7c/0x108
gemini-ethernet-port: caps=(0x0000010000154813, 0x00002007ffdd7889)
And the packets do not go through.
The TSO implementation is bogus: a TSO enabled driver must propagate
the skb_shinfo(skb)->gso_size value to the TSO engine on the NIC.
Drop the size check and TSO offloading features for now: this
needs to be fixed up properly.
After this ethernet works fine on Gemini devices with a direct connected
PHY such as D-Link DNS-313.
Also tested to still be working with a DSA switch using the Gemini
ethernet as conduit interface.
Link: https://lore.kernel.org/netdev/CANn89iJLfxng1sYL5Zk0mknXpyYQPCp83m3KgD2KJ2_hKCpEUg@mail.gmail.com/
Suggested-by: Eric Dumazet <edumazet@google.com>
Fixes: d4d0c5b4d2 ("net: ethernet: cortina: Handle large frames")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX max frame size is over 10000 for the Gemini ethernet,
but the TX max frame size is actually just 2047 (0x7ff after
checking the datasheet). Reflect this in what we offer to Linux,
cap the MTU at the TX max frame minus ethernet headers.
We delete the code disabling the hardware checksum for large
MTUs as netdev->mtu can no longer be larger than
netdev->max_mtu meaning the if()-clause in gmac_fix_features()
is never true.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-3-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Gemini ethernet controller provides hardware checksumming
for frames up to 1514 bytes including ethernet headers but not
FCS.
If we start sending bigger frames (after first bumping up the MTU
on both interfaces sending and receiving the frames), truncated
packets start to appear on the target such as in this tcpdump
resulting from ping -s 1474:
23:34:17.241983 14:d6:4d:a8:3c:4f (oui Unknown) > bc:ae:c5:6b:a8:3d (oui Unknown),
ethertype IPv4 (0x0800), length 1514: truncated-ip - 2 bytes missing!
(tos 0x0, ttl 64, id 32653, offset 0, flags [DF], proto ICMP (1), length 1502)
OpenWrt.lan > Fecusia: ICMP echo request, id 1672, seq 50, length 1482
If we bypass the hardware checksumming and provide a software
fallback, everything starts working fine up to the max TX MTU
of 2047 bytes, for example ping -s2000 192.168.1.2:
00:44:29.587598 bc:ae:c5:6b:a8:3d (oui Unknown) > 14:d6:4d:a8:3c:4f (oui Unknown),
ethertype IPv4 (0x0800), length 2042:
(tos 0x0, ttl 64, id 51828, offset 0, flags [none], proto ICMP (1), length 2028)
Fecusia > OpenWrt.lan: ICMP echo reply, id 1683, seq 4, length 2008
The bit enabling to bypass hardware checksum (or any of the
"TSS" bits) are undocumented in the hardware reference manual.
The entire hardware checksum unit appears undocumented. The
conclusion that we need to use the "bypass" bit was found by
trial-and-error.
Since no hardware checksum will happen, we slot in a software
checksum fallback.
Check for the condition where we need to compute checksum on the
skb with either hardware or software using == CHECKSUM_PARTIAL instead
of != CHECKSUM_NONE which is an incomplete check according to
<linux/skbuff.h>.
On the D-Link DIR-685 router this fixes a bug on the conduit
interface to the RTL8366RB DSA switch: as the switch needs to add
space for its tag it increases the MTU on the conduit interface
to 1504 and that means that when the router sends packages
of 1500 bytes these get an extra 4 bytes of DSA tag and the
transfer fails because of the erroneous hardware checksumming,
affecting such basic functionality as the LuCI web interface.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-2-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enumerator 3 is 1548 bytes according to the datasheet.
Not 1542.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20231109-gemini-largeframe-fix-v4-1-6e611528db08@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not possible for platform_get_irq() to return 0. Use the
return value from platform_get_irq().
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20230802085216.659238-1-ruanjinjie@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On 32bit-UP u64_stats_fetch_begin() disables only preemption. If the
reader is in preemptible context and the writer side
(u64_stats_update_begin*()) runs in an interrupt context (IRQ or
softirq) then the writer can update the stats during the read operation.
This update remains undetected.
Use u64_stats_fetch_begin_irq() to ensure the stats fetch on 32bit-UP
are not interrupted by a writer. 32bit-SMP remains unaffected by this
change.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Catherine Sullivan <csully@google.com>
Cc: David Awogbemila <awogbemila@google.com>
Cc: Dimitris Michailidis <dmichail@fungible.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jeroen de Borst <jeroendb@google.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Simon Horman <simon.horman@corigine.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: oss-drivers@corigine.com
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defining local versions of NAPI_POLL_WEIGHT with the same
values in the drivers just makes refactoring harder.
Drop the special defines in a bunch of drivers where the
removal is relatively simple so grouping into one patch
does not impact reviewability.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The four RGMII interface modes take care of the required RGMII delay
configuration at the PHY and should not be limited by the network MAC
driver. Sadly, gemini was only permitting RGMII mode with no delays,
which would require the required delay to be inserted via PCB tracking
or by the MAC.
However, there are designs that require the PHY to add the delay, which
is impossible without Gemini permitting the other three PHY interface
modes. Fix the driver to allow these.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Link: https://lore.kernel.org/r/E1n4mpT-002PLd-Ha@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of drivers use eth_random_addr(netdev->dev_addr)
thus writing to netdev->dev_addr directly, and not setting
the address type. Switch them to eth_hw_addr_random().
@@
expression netdev;
@@
- eth_random_addr(netdev->dev_addr);
+ eth_hw_addr_random(netdev);
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
eth_hw_addr_set() takes a u8 pointer, like other
etherdevice helpers. Convert the few drivers which
require casts because they memcpy from "endian marked"
types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cortina/gemini.c: In function gmac_get_ringparam:
drivers/net/ethernet/cortina/gemini.c:2125:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/cortina/gemini.c: In function gmac_init:
drivers/net/ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
these variable is never used, so remove it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's nice if the phy is online before we register the netdev
so try to do that first.
Stop trying to do "second tried" to register the phy, it
works perfectly fine the first time.
Stop remvoving the phy in uninit. Remove it when the
driver is remove():d, symmetric to where it is added, in
probe().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We recently added some calls to clk_disable_unprepare() but we missed
the last error path if register_netdev() fails.
I made a couple cleanups so we avoid mistakes like this in the future.
First I reversed the "if (!ret)" condition and pulled the code in one
indent level. Also, the "port->netdev = NULL;" is not required because
"port" isn't used again outside this function so I deleted that line.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace alloc_etherdev_mq with devm_alloc_etherdev_mqs. In this way,
when probe fails, netdev can be freed automatically.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the missing clk_disable_unprepare() before return
from gemini_ethernet_port_probe() in the error handling case.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use default ethtool version instead of static variant.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of gmac_setup_txqs() the allocated desc_ring is
leaked if TX queue base is not aligned. Release it via
dma_free_coherent.
Fixes: 4d5ae32f5e ("net: ethernet: Add a driver for Gemini gigabit ethernet")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not advertize NETIF_F_FRAGLIST, the stack can't
pass skbs with frags lists to the xmit function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX stats should be started with the tx_stats_syncp,
there seems to be a copy/paste error in the driver.
Signed-off-by: Andreas Fiedler <andreas.fiedler@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have the MAC drivers manipulate phydev members to indicate
they support Asym Pause, add a helper function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet MAC drivers want to limit the PHY to only advertise a
maximum speed of 100Mbs or 1Gbps. Rather than using a mask, make use
of the helper function phy_set_max_speed().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
