Fix typos in comments and error messages.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: David Arinzon <darinzon@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250723201528.2908218-1-helgaas@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This moves bnxt_hsi.h contents to a common location so it can be
properly referenced by bnxt_en, bnxt_re, and bnge.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250714170202.39688-1-gospo@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improved wording and grammar in several comments for clarity.
"the must belongs" -> "it must belong"
"mininum" -> "minimum"
"fileds" -> "fields"
Replaced return -1 with -EINVAL in hwrm_ring_alloc_send_msg()
to return a proper error code.
These changes enhance code readability and consistent error handling.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250615154051.1365631-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Only devlink and sriov paths are grabbing rtnl explicitly. The rest is
covered by netdev instance lock which the core now grabs, so there is
no need to manage rtnl in most places anymore.
On the core side we can now try to drop rtnl in some places
(do_setlink for example) for the drivers that signal non-rtnl
mode (TBD).
Boot-tested and with `ethtool -L eth1 combined 24` to trigger reset.
Cc: Saeed Mahameed <saeed@kernel.org>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250305163732.2766420-15-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During driver load, PF RDMA driver provisions resources
to the RDMA VFs. This logic takes into consideration of
the total number of VFs supported on the PF while
allocating resources. Firmware now advertises a capability
where NIC driver can allocate resources for RDMA VFs when
the user actually creates a VF. So this resource
distribution can be based on the number of active VFs.
This patch adds the support to check for the firmware
capability and follow the new RDMA VF resource allocation
strategy. The current logic in the RDMA driver will be
removed for the newer Firmware versions in a subsequent
patch in this series.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Reviewed-by: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730882676-24434-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Now that we only support MSIX, the BNXT_FLAG_USING_MSIX is always true.
Remove it and any if conditions checking for it. Remove the INTX
handler and associated logic.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Hongguang Gao <hongguang.gao@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240828183235.128948-6-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
With recent changes in the .ndo_set_vf_*() guidelines, resubmitting
this patch that was reverted eariler in 2023:
c27153682e ("Revert "bnxt_en: Support QOS and TPID settings for the SRIOV VLAN")
Add these missing settings in the .ndo_set_vf_vlan() method.
Older firmware does not support the TPID setting so check for
proper support.
Remove the unused BNXT_VF_QOS flag.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20240828183235.128948-4-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Firmware interface 1.10.2.118 has increased the size of
HWRM_PORT_PHY_QCFG response beyond the maximum size that can be
forwarded. When the VF's link state is not the default auto state,
the PF will need to forward the response back to the VF to indicate
the forced state. This regression may cause the VF to fail to
initialize.
Fix it by capping the HWRM_PORT_PHY_QCFG response to the maximum
96 bytes. The SPEEDS2_SUPPORTED flag needs to be cleared because the
new speeds2 fields are beyond the legacy structure. Also modify
bnxt_hwrm_fwd_resp() to print a warning if the message size exceeds 96
bytes to make this failure more obvious.
Fixes: 84a911db83 ("bnxt_en: Update firmware interface to 1.10.2.118")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20240612231736.57823-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation to support a new P7 chip which has a lot of similarities
with the P5 chip, rename the BNXT_FLAG_CHIP_P5 flag to
BNXT_FLAG_CHIP_P5_PLUS. This will make it clear that the flag is for
P5 and newer chips.
Also, since there are no additional P5 variants in production, rename
BNXT_FLAG_CHIP_P5_THOR() to BNXT_FLAG_CHIP_P5() to keep the naming
more simple.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Reviewed-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Randy Schacher <stuart.schacher@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231120234405.194542-14-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Recent FW interface update bumped the size of struct hwrm_func_cfg_input
above 128B which is the max some devices support.
Probe on Stratus (BCM957452) with FW 20.8.3.11 fails with:
bnxt_en ...: Unable to reserve tx rings
bnxt_en ...: 2nd rings reservation failed.
bnxt_en ...: Not enough rings available.
Once probe is fixed other errors pop up:
bnxt_en ...: Failed to set async event completion ring.
This is because __hwrm_send() rejects requests larger than
bp->hwrm_max_ext_req_len with -E2BIG. Since the driver doesn't
actually access any of the new fields, yet, trim the length.
It should be safe.
Similar workaround exists for backing_store_cfg_input.
Although that one mins() to a constant of 256, not 128
we'll effectively use here. Michael explains: "the backing
store cfg command is supported by relatively newer firmware
that will accept 256 bytes at least."
To make debugging easier in the future add a warning
for oversized requests.
Fixes: 754fbf604f ("bnxt_en: Update firmware interface to 1.10.2.171")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20231016171640.1481493-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newer versions of firmware will pre-reserve 1 VNIC for every possible
PF and VF function. Update the driver logic to take this into account
when assigning VNICs to the VFs. These pre-reserved VNICs for the
inactive VFs should be subtracted from the global pool before
assigning them to the active VFs.
Not doing so may cause discrepancies that ultimately may cause some VFs to
have insufficient VNICs to support features such as aRFS.
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add these missing settings in the .ndo_set_vf_vlan() method.
Older firmware does not support the TPID setting so check for
proper support.
Remove the unused BNXT_VF_QOS flag.
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an inability of bnxt_en driver to set eswitch to switchdev
mode without existing VFs by:
1. Allow to set switchdev mode in bnxt_dl_eswitch_mode_set() so
representors are created only when num_vfs > 0 otherwise just
set bp->eswitch_mode
2. Do not automatically change bp->eswitch_mode during
bnxt_vf_reps_create() and bnxt_vf_reps_destroy() calls so
the eswitch mode is managed only by an user by devlink.
Just set temporarily bp->eswitch_mode to legacy to avoid
re-opening of representors during destroy.
3. Create representors in bnxt_sriov_enable() if current eswitch
mode is switchdev one
Tested by this sequence:
1. Set PF interface up
2. Set PF's eswitch mode to switchdev
3. Created N VFs
4. Checked that N representors were created
5. Set eswitch mode to legacy
6. Checked that representors were deleted
7. Set eswitch mode back to switchdev
8. Checked that representors exist again for VFs
9. Deleted all VFs
10. Checked that all representors were deleted as well
11. Checked that current eswitch mode is still switchdev
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Link: https://lore.kernel.org/r/20230411120443.126055-1-ivecera@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Remove the SRIOV config callback which the bnxt_en was calling
to reconfigure the chip resources for a PF device when VFs are
created. The code is now modified to provision the VF resources
based on the total VF count instead of the actual VF count.
This allows the SRIOV config callback to be removed from the
list of ulp_ops.
Suggested-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
There are 2 issues:
1. We should decrement hw_resc->max_nqs instead of hw_resc->max_irqs
with the number of NQs assigned to the VFs. The IRQs are fixed
on each function and cannot be re-assigned. Only the NQs are being
assigned to the VFs.
2. vf_msix is the total number of NQs to be assigned to the VFs. So
we should decrement vf_msix from hw_resc->max_nqs.
Fixes: b16b689186 ("bnxt_en: Add SR-IOV support for 57500 chips.")
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If bnxt_sriov_enable() fails after some resources have been reserved
for the VFs, the current code is not unwinding properly and the
reserved resources become unavailable afterwards. Fix it by
properly unwinding with a call to bnxt_hwrm_func_qcaps() to
reset all maximum resources.
Also, add the missing bnxt_ulp_sriov_cfg() call to let the RDMA
driver know to abort.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The commit a14857c27a ("rtnetlink: verify rate parameters for calls to
ndo_set_vf_rate") has been merged to master, so we can to remove the
now-duplicate checks in drivers.
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220609084717.155154-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prep for .eswitch_mode_set being called with the devlink instance
lock held use that lock explicitly instead of creating a local mutex
just for the sriov reconfig.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion follows this general pattern for most of the calls:
1. The input message is changed from a stack variable initialized
using bnxt_hwrm_cmd_hdr_init() to a pointer allocated and intialized
using hwrm_req_init().
2. If we don't need to read the firmware response, the hwrm_send_message()
call is replaced with hwrm_req_send().
3. If we need to read the firmware response, the mutex lock is replaced
by hwrm_req_hold() to hold the response. When the response is read, the
mutex unlock is replaced by hwrm_req_drop().
If additional DMA buffers are needed for firmware response data, the
hwrm_req_dma_slice() is used instead of calling dma_alloc_coherent().
Some minor refactoring is also done while doing these conversions.
v2: Fix unintialized variable warnings in __bnxt_hwrm_get_tx_rings()
and bnxt_approve_mac()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the hwrm_cmd_lock to serialize the update of the
firmware's link status response data and the copying of link status data
to the VF. This won't work when we update the firmware message APIs, so
we use the link_lock mutex instead. All link_info data should be
updated under the link_lock mutex. Also add link_lock to functions that
touch link_info in __bnxt_open_nic() and bnxt_probe_phy(). The locking
is probably not strictly necessary during probe, but it's more consistent.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the PTP related firmware interface is the main change.
There is also a name change for admin_mtu, requiring code fixup.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF is no longer enforcing an assigned MAC address on a VF, the
VF needs to call bnxt_approve_mac() to tell the PF what MAC address it is
now using. Otherwise it gets out of sync and the PF won't know what
MAC address the VF wants to use. Ultimately the VF will fail when it
tries to setup the L2 MAC filter for the vnic.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it before bnxt_update_vf_mac(). In the next patch, we need to call
bnxt_approve_mac() from bnxt_update_mac() under some conditions. This
will avoid forward declaration.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is perfectly legal for the stack to query and configure VFs via PF
NDOs while the NIC is administratively down. Remove the unnecessary
check for the PF to be in open state.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware previously only allowed promiscuous mode for VFs associated with
a default VLAN. It is now possible to enable promiscuous mode for a VF
having no VLAN configured provided that it is trusted. In such cases the
VF will see all packets received by the PF, irrespective of destination
MAC or VLAN.
Note, it is necessary to query firmware at the time of bnxt_promisc_ok()
instead of in bnxt_hwrm_func_qcfg() because the trusted status might be
altered by the PF after the VF has been configured. This check must now
also be deferred because the firmware call sleeps.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware does not expect the CRC to be included in the length
passed from the driver. The firmware always configures the chip
to strip out the CRC.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the logic that sets the enable/disable flag for the source MAC
filter according to firmware spec 1.7.1.
In the original firmware spec. before 1.7.1, the VF spoof check flags
were not latched after making the HWRM_FUNC_CFG call, so there was a
need to keep the func_flags so that subsequent calls would perserve
the VF spoof check setting. A change was made in the 1.7.1 spec
so that the flags became latched. So we now set or clear the anti-
spoof setting directly without retrieving the old settings in the
stored vf->func_flags which are no longer valid. We also remove the
unneeded vf->func_flags.
Fixes: 8eb992e876 ("bnxt_en: Update firmware interface spec to 1.7.6.2.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently only assignes 1 RSS context to each VF. This works
for the Linux VF driver. But other drivers, such as DPDK, can make use
of additional RSS contexts. Modify the code to divide up and assign
RSS contexts to VFs just like other resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Retain the VF MAC address, default VLAN, TX rate control, trust settings
of VFs after firmware reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new flag will be set in subsequent patches when firmware is
going through reset. If bnxt_close() is called while the new flag
is set, the FW reset sequence will have to be aborted because the
NIC is prematurely closed before FW reset has completed. We also
reject SRIOV configurations while FW reset is in progress.
v2: No longer drop rtnl_lock() in close and wait for FW reset to complete.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs need to be reconfigured dynamically after firmwware reset, the
configuration sequence on the PF needs to be changed to register the VF
buffers first. Otherwise, some VF firmware commands may not succeed as
there may not be PF buffers ready for the re-directed firmware commands.
This sequencing did not matter much before when we only supported
the normal bring-up of VFs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the hardware/firmware configuration portion in
bnxt_sriov_enable() into a new function bnxt_cfg_hw_sriov(). This
new function can be called after a firmware reset to reconfigure the
VFs previously enabled.
v2: straight refactor of the code. Reordering done in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 4 functions handling message forwarding for SR-IOV. They
check for non-zero firmware response code and then return -1. There
is no need to do this anymore. The main messaging function will
now return standard error code. Since we don't need to examine the
response, we can use the hwrm_send_message() variant which will
take the mutex automatically.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace. Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware. Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some minor differences when assigning VF resources on the
new chips. The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly. The
VFs will be assigned these available CP rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e9660 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
