57500 series is a new chip class (P5) that requires some driver changes
in the next several patches. This adds basic chip ID, doorbells, and
the notification queue (NQ) structures. Each MSIX is associated with an
NQ instead of a CP ring in legacy chips. Each NQ has up to 2 associated
CP rings for RX and TX. The same bnxt_cp_ring_info struct will be used
for the NQ.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New device requires host context memory as a backing store. Call
firmware to check for context memory requirements and store the
parameters. Allocate host pages accordingly.
We also need to move the call bnxt_hwrm_queue_qportcfg() earlier
so that all the supported hardware queues and the IDs are known
before checking and allocating context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips require the PTU_PTE_VALID bit to be set for every page
table entry for context memory and rings. Additional bits are also
required for page table entries for all rings. Add a flags field to
bnxt_ring_mem_info struct to specify these additional bits to be used
when setting up the pages tables as needed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the DMA page table and vmem fields in bnxt_ring_struct to a new
bnxt_ring_mem_info struct. This will allow context memory management
for a new device to re-use some of the existing infrastructure.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New firmware spec. allows interrupt coalescing parameters, such as
maximums, timer units, supported features to be queried. Update
the driver to make use of the new call to query these parameters
and provide the legacy defaults if the call is not available.
Replace the hard-coded values with these parameters.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the max_ext_req_len field from the HWRM_VER_GET_RESPONSE.
If this field is valid and greater than the mailbox size, use the
short command format to send firmware messages greater than the
mailbox size. Newer devices use this method to send larger messages
to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest firmware spec. has some additional rx extended port stats and new
tx extended port stats added. We now need to check the size of the
returned rx and tx extended stats and determine how many counters are
valid. New counters added include CoS byte and packet counts for rx
and tx.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Among the new changes are trusted VF support, 200Gbps support, and new
API to dump ring information on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea5 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused bnxt_subtract_ulp_resources(). Change
bnxt_get_max_func_irqs() to static since it is only locally used.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expand the .ieee_setapp() and ieee_delapp() DCBNL methods to support
DSCP. This allows DSCP values to user priority mappings instead
of using VLAN priorities. Each DSCP mapping is added or deleted one
entry at a time using the firmware API. The firmware call can only be
made from a PF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export temperature sensor reading via hwmon sysfs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use latest firmware API to notify firmware about IF state changes.
Firmware has the option to clean up resources during IF down and
to require the driver to reserve resources again during IF up.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags field is almost getting full. Move firmware capability flags
to a new fw_cap field to better organize these firmware flags.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the default hash mode flag in HWRM_VNIC_RSS_CFG to signal to the
firmware that the driver is compliant with the latest spec. With
that, the firmware can return expanded RSS profile IDs that the driver
checks to setup the proper gso_type for GRO-HW packets. But instead
of checking for the new profile IDs, we check the IP_TYPE flag
in TPA_START which is more straight forward than checking a list of
profile IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During hotplug, the driver's open function can be called almost
immediately after power on reset. The PHY may not be ready and the
firmware may return failure when the driver tries to update PHY
settings. Add retry logic fired from the driver's timer to retry
the operation for 5 seconds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to detect firmware support for external loopback and the extra
test entry for external loopback.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New interface has firmware core dump support, new extended port
statistics, and IF state change notifications to the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_dbg_resp_addr and hwrm_dbg_resp_dma_addr are never used
and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling bnxt_set_max_func_irqs() to modify the max IRQ count requested or
freed by the RDMA driver is flawed. The max IRQ count is checked when
re-initializing the IRQ vectors and this can happen multiple times
during ifup or ethtool -L. If the max IRQ is reduced and the RDMA
driver is operational, we may not initailize IRQs correctly. This
problem shows up on VFs with very small number of MSIX.
There is no other logic that relies on the IRQ count excluding the ones
used by RDMA. So we fix it by just removing the call to subtract or
add the IRQs used by RDMA.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SFP+ modules, 0xA2 page is available only when Diagnostic Monitoring
Type [Address A0h, Byte 92] is implemented. Extend bnxt_get_module_info(),
to read optical diagnostics support at offset 92(0x5c) and set eeprom_len
length to ETH_MODULE_SFF_8436_LEN (to exclude A2 page), if dianostics is
not supported.
Also in bnxt_get_module_info(), module id is read from offset 0x5e which
is not correct. It was working by accident, as offset was not effective
without setting enables flag in the firmware request. SFP module id is
present at location 0. Fix this by removing the offset and read it
from location 0.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent change to reduce delay granularity waiting for firmware
reponse has caused a regression. With a tighter delay loop,
the driver may see the beginning part of the response faster.
The original 5 usec delay to wait for the rest of the message
is not long enough and some messages are detected as invalid.
Increase the maximum wait time from 5 usec to 20 usec. Also, fix
the debug message that shows the total delay time for the response
when the message times out. With the new logic, the delay time
is not fixed per iteration of the loop, so we define a macro to
show the total delay time.
Fixes: 9751e8e714 ("bnxt_en: reduce timeout on initial HWRM calls")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds debugfs support for bnxt_en with the purpose of allowing users
to examine the current DIM profile in use for each receive queue. This
was instrumental in debugging issues found with DIM and ensuring that
the profiles we expect to use are the profiles being used.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing with DIM enabled on older kernels indicated that firmware calls
were slower than expected. More detailed analysis indicated that the
default 25us delay was higher than necessary. Reducing the time spend in
usleep_range() for the first several calls would reduce the overall
latency of firmware calls on newer Intel processors.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver maps MQPRIO traffic classes directly 1:1 to the
internal hardware queues (TC0 maps to hardware queue 0, etc). This
direct mapping requires the internal hardware queues to be reconfigured
from lossless to lossy and vice versa when necessary. This
involves reconfiguring internal buffer thresholds which is
disruptive and not always reliable.
Implement a new scheme to map TCs to internal hardware queues by
matching up their PFC requirements. This will eliminate the need
to reconfigure a hardware queue internal buffers at run time. After
remapping, the NIC is closed and opened for the new TC to hardware
queues to take effect.
This patch only adds the basic mapping logic.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add additional logic to reserve completion rings for the bnxt_re driver
when it requests MSIX vectors. The function bnxt_cp_rings_in_use()
will return the total number of completion rings used by both drivers
that need to be reserved. If the network interface in up, we will
close and open the NIC to reserve the new set of completion rings and
re-initialize the vectors.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver code makes some assumptions about the group index
and the map index of rings. This makes the code more difficult to
understand and less flexible.
Improve it by adding the grp_idx and map_idx fields explicitly to the
bnxt_ring_struct as a union. The grp_idx is initialized for each tx ring
and rx agg ring during init. time. We do the same for the map_idx for
each cmpl ring.
The grp_idx ties the tx ring to the ring group. The map_idx is the
doorbell index of the ring. With this new infrastructure, we can change
the ring index mapping scheme easily in the future.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for the maximum pre-set TX channels for ethtool -l, we
need to check the current max_tx_scheduler_inputs parameter from firmware.
This parameter specifies the max input for the internal QoS nodes currently
available to this function. The function's TX rings will be capped by this
parameter. By adding this logic, we provide a more accurate pre-set max
TX channels to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic extended port statistics, if the device is PF and
link is up.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the RDMA driver is registered, use a new VNIC mode that allows
RDMA traffic to be seen on the netdev in promiscuous mode.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor changes, such as new extended port statistics.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code includes wmb() followed by writel(). writel() already has a barrier on
some architectures like arm64.
This ends up CPU observing two barriers back to back before executing the
register write.
Create a new wrapper function with relaxed write operator. Use the new
wrapper when a write is following a wmb().
Since code already has an explicit barrier call, changing writel() to
writel_relaxed().
Also add mmiowb() so that write code doesn't move outside of scope.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a packet with VLAN tag, pass the entire 16-bit TCI to the
stack when calling __vlan_hwaccel_put_tag(). The current code is only
passing the 12-bit tag and it is missing the priority bits.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver exports different switchdev PARENT_IDs for
representors belonging to different SR-IOV PF-pools of an adapter.
This is not correct as the adapter can switch across all vports
of an adapter. This patch fixes this by exporting a common switchdev
PARENT_ID for all reps of an adapter. The PCIE DSN is used as the id.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context. This will allow "ip link show"
to display all VF MAC addresses.
Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.
Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.
The min is the absolute minimum for each VF to function. The max is the
global resources minus the resources used by the PF. Each VF is
guaranteed the min. Up to max resources may be available for some VFs.
The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources. The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources. Use the new API when it is supported by firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized. Otherwise they cannot be re-used by
the PF. For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.
To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version has new firmware APIs to allocate PF/VF resources more
flexibly.
New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the changes needed for the bnxt_en driver to add support
for dynamic interrupt moderation per ring.
This does add additional counters in the receive path, but testing shows
that any additional instructions are offset by throughput gain when the
default configuration is for low latency.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver hook points for xdp_rxq_info:
* reg : bnxt_alloc_rx_rings
* unreg: bnxt_free_rx_rings
This driver should be updated to re-register when changing
allocation mode of RX rings.
Tested on actual hardware.
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
TC flower is not enabled on VFs and when there's no FW support.
Alloc the tc_info{} struct at init time only when TC flower is being
enabled.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements periodic querying of cfa flow stats
in batches to compute the 'lastused' attribute of TC flow stats.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPv4 vxlan encap/decap action support to TC-flower
offload.
For vxlan encap, the driver maintains a tunnel encap hash-table.
When a new flow with a tunnel encap action arrives, this table
is looked up; if an encap entry exists, it uses the already
programmed encap_record_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new encap node is added and the
L2 header fields are queried via a route lookup.
hwrm_cfa_encap_record_alloc cmd is used to create a new encap
record and the encap_record_handle is used as the tunnel_handle
while adding the flow.
For vxlan decap, the driver maintains a tunnel decap hash-table.
When a new flow with a tunnel decap action arrives, this table
is looked up; if a decap entry exists, it uses the already
programmed decap_filter_handle as the tunnel_handle in the
hwrm_cfa_flow_alloc cmd. Else, a new decap node is added and
a decap_filter_handle is alloc'd via the hwrm_cfa_decap_filter_alloc
cmd. This handle is used as the tunnel_handle while adding the flow.
The code to issue the HWRM FW cmds is introduced in a follow-up patch.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IRQ coalescing logic is a little messy. The ethtool
parameters are mapped to hardware parameters in a way that is difficult
to understand. The first step is to better organize the parameters
by adding the new structure bnxt_coal. The structure is used by both
the RX and TX sets of coalescing parameters.
Adjust the default coal_ticks to 14 us and 28 us for RX and TX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
