Currently, SPI-Engine offload module always sends 32-bit data elements to
DMA engine. Appropriately, when set for SPI offloading, the IIO driver uses
32 storagebits for IIO ADC channel buffer elements. However, setting SPI
transfer length according to storagebits (32-bits in case of offload) can
lead to unnecessarily long transfers for ADCs that are 16-bit or less
precision. Adjust AD4000 single-shot read to run transfers of 2 bytes when
that is enough to get all ADC data bits.
Fixes: 59b51edf71 ("iio: adc: ad4000: Add support for SPI offload")
Suggested-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/8f765cfd6e93fad4e755dd95d709b7bea2a388e2.1744718916.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This new function allows us to perform debug checks in the helper to ensure
that the overrun does not occur. Use it in all the simple cases where
either a static buffer or a structure is used in the drivers.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20250413103443.2420727-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
FPGA HDL projects can include a PWM generator in addition to SPI-Engine.
The PWM IP is used to trigger SPI-Engine offload modules that in turn set
SPI-Engine to execute transfers to poll data from the ADC. That allows data
to be read at the maximum sample rates. Also, it is possible to set a
specific sample rate by setting the proper PWM duty cycle and related state
parameters, thus allowing an adjustable ADC sample rate when a PWM (offload
trigger) is used in combination with SPI-Engine.
Add support for SPI offload.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/386ce043a0e3fc9e8ff71f17aef8de128ce5869e.1743110188.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This complex cleanup.h use case of conditional guards has proved
to be more trouble that it is worth in terms of false positive compiler
warnings and hard to read code.
Move directly to the new claim/release_direct() that allow sparse
to check for unbalanced context.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Tested-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20250209180624.701140-10-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use this new type to both slightly simplify the code and avoid
confusing static analysis tools. Mostly this series is about consistency
to avoid this code pattern getting copied into more drivers.
Acked-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241215182912.481706-14-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADI PulSAR series of single-channel devices comprises differential and
pseudo-differential ADCs that don't require any input data from the host
controller. By not requiring a data input line, PulSAR devices can operate
with a 3-wire only data bus in some setups.
The AD4000 series and the single-channel PulSAR series of devices have
similar SPI transfer specifications and wiring configurations.
Single-channel PulSAR devices are slower than AD4000 and don't have a
configuration register. That taken into account, single-channel PulSARs can
be supported by the ad4000 driver without any increase in code complexity.
Extend the AD4000 driver to also support single-channel PulSAR devices.
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/2bfb904e29914c3dc4905e1c87fcc735575f330d.1733147444.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The SPI transfers for AD4020, AD4021, and AD4022 have slightly different
timing specifications. Use device specific timing constraints to set SPI
transfer parameters. While tweaking time constraints, remove time related
defines including unused AD4000_TQUIET1_NS.
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/a36fcf44cc00b2a498170e2ae3f005829d516266.1733147444.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC data is pushed to the IIO buffer along with timestamp but no
timestamp channel was provided to retried the time data.
Add a timestamp channel to provide sample capture time.
Suggested-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/d1f1bb1b726b90a3a7c1148c65d2f7fe073e2b15.1733147444.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alongside new drivers and device support there are several large
cleanups going on across the IIO tree and we see part of some of those
in this pull request.
Merged char-misc-next at point of 6.12-rc6 merge to avoid a
conflict with a fix for the ad7380 merged earlier this cycle.
Note that I previously messed this merge up and had to reconstruct
it this morning so a coherent pull request was possible. The new
stuff is all the same as has been in linux-next for some time with
the exception of the kernel-doc related __private ordering fix
that went in yesterday.
New device support
==================
adi,ad7380
- Support for adaq4370-4 and adaq4370 quad channel ADCs.
adi,ad7606
- Various cleanups preceeding support of AD7607, AD7608 and AD7609 ADCs.
adi,ad7779
- New driver supproting AD7770, AD7771 and AD7779 ADCs.
allegro,als31300
- New driver for this 3D Linear Hall Effect sensor.
bosch,bmi270
- Add support BMI260 which is similar but requires a different firmware image.
bosch,smi240
- New driver for this IMU.
ti,opt3001
- Add support opt3002 light sensor which has a wider spectral range than
the opt3001.
vishay,veml3235
- New driver for this ambient light sensor.
Features
========
hid-sensors
- Add support Human Proximity Range and Attention detection (requiring
a new classification style channel type)
adi,ad3552r
- Add backend support and related platform driver to support use
with an FPGA IP to allow QSPI + DDR bus operation and much higher
data aquisition rates. (various rework preceeded this feature)
adi,ad7606
- Various cleanup prior to enabling use with an IIO Backend and PWM trigger
enabling much higher speed data capture.
bosch,bme680
- Support control of preheat current
- Support triggered buffer capture
- Add SCALE and RAW channels (needed to enable the buffered capture).
bosch,bmp280
- Enable sleeping to save power.
- Add interrupt support for bmp3xx and bmp5xx devices. Also update bmp085
to new approach.
- Enable data ready trigger.
bosch,bmi270
- Add triggered buffer support
- Add scale and sampling frequency control.
vishay,veml6070
- Support integration time via DT binding for an external resistor value.
Cleanup and minor fixes
=======================
core
- Fix a longstanding issue with event codes for differential channels.
Note that not all drivers are yet fixed, but macros have been added
to avoid potential repeats of this in future.
- Tidy up handling in iio_read_acpi_mount matrix.
- Mark iio_dev::priv with __private. Later move the marking before the
field name to avoid a kernel-doc issue.
treewide
- Drop some pointless default n entries in Kconfig.
- Add an iio_get_acpi_device_name_and_data() handler to replace some
commonly repeated code.
- simplify use of 'state' in write_event_config() callback as it is
effectively a boolean. Once done make it a boolean (lots of drivers
were updated to enable this)
- some more use of devm_regulator_get_enable_read_voltage( to replace
open coded versions. Where this enables it convert all of remove
handling to devm based and drop the remove callback.
- check returns from devm_mutex_init()
accel drivers
- Use aligned_s64 instead of s64 __aligned(8)
adi,ad5791
- Add some missing GPIOs and power supplies that presumably were always
hard wired on previous boards.
- Refactor to use chip_info in device id tables.
- Convert probe entirely to devm based simplify code and allowing remove()
callback to be dropped.
adi,ad7192
- Check return from spi_get_device_match_data()
adi,ad74413r
- Don't keep an unnecessary copy of the gpio after probe.
- Use devm_regulator_get_enable_read_voltage() instead of open coding.
- Apply cleanup.h approach to reduce complexity.
adi,dac8460
- Fix a wrong compaitble ID due to a stray space.
- Add an spi_device_id table.
bosch,bmc150
- Drop some likely false ACPI IDs.
- Drop left over unused ACPI specific code.
bosch,bme680
- Add mising regmap.h include.
- Reduce excessive sleep on startup.
- Drop some cammelcase usage.
- Use fsleep
- Generalize read functions to allow for reuse.
- Use s16 variable to avoid some incorrect casting
bosch,bmg150
- Drop some likely false ACPI IDs.
bosch,bmi270
- Drop unused FREQUENCY and SCALE attributes that always returned an
error (they wil be back impelmented correctly).
- Factor out the chip specific data into a structure to enable simple
support for additional devices.
isil,isl29018
- Drop ACPI_PTR() and CONFIG_ACPI guards as not worth the trouble for very
minor saving.
invensense,mpu6050
- Use much simpler test for ACPI firmware.
kionix,kxcjk-1013
- Drop unnecessary ACPI entry in the i2c_device_id table.
- Drop support KX022-1020 to fix a bug that was introduced with that change.
Hopefully a fixed version will replace it soon.
- Drop CONFIG guards for PM in favor of pm_ptr() and the compiler removing
dead code.
- Switch from enum to chip_info structure and add ODR times to that structure.
- Deduplicate one of those ODR structures
- Drop ACPI_PTR() and move ID table out of config guards.
- Minor additional cleanup.
liteon,ltr401
- Drop some likely false ACPI Ids and add LTER0303 which is know to be in use.
microchip,pac1934
- Use much simpler test for ACPI firmware.
vishay,veml6070
- Use unsigned int instead of just unsigned.
- Use FIELD_PREP to make setting of field value explicit.
Various other minor fixes to documentation
-----BEGIN PGP SIGNATURE-----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=tB/u
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 2nd set of new device support, features and cleanup for 6.13
Alongside new drivers and device support there are several large
cleanups going on across the IIO tree and we see part of some of those
in this pull request.
Merged char-misc-next at point of 6.12-rc6 merge to avoid a
conflict with a fix for the ad7380 merged earlier this cycle.
Note that I previously messed this merge up and had to reconstruct
it this morning so a coherent pull request was possible. The new
stuff is all the same as has been in linux-next for some time with
the exception of the kernel-doc related __private ordering fix
that went in yesterday.
New device support
==================
adi,ad7380
- Support for adaq4370-4 and adaq4370 quad channel ADCs.
adi,ad7606
- Various cleanups preceeding support of AD7607, AD7608 and AD7609 ADCs.
adi,ad7779
- New driver supproting AD7770, AD7771 and AD7779 ADCs.
allegro,als31300
- New driver for this 3D Linear Hall Effect sensor.
bosch,bmi270
- Add support BMI260 which is similar but requires a different firmware image.
bosch,smi240
- New driver for this IMU.
ti,opt3001
- Add support opt3002 light sensor which has a wider spectral range than
the opt3001.
vishay,veml3235
- New driver for this ambient light sensor.
Features
========
hid-sensors
- Add support Human Proximity Range and Attention detection (requiring
a new classification style channel type)
adi,ad3552r
- Add backend support and related platform driver to support use
with an FPGA IP to allow QSPI + DDR bus operation and much higher
data aquisition rates. (various rework preceeded this feature)
adi,ad7606
- Various cleanup prior to enabling use with an IIO Backend and PWM trigger
enabling much higher speed data capture.
bosch,bme680
- Support control of preheat current
- Support triggered buffer capture
- Add SCALE and RAW channels (needed to enable the buffered capture).
bosch,bmp280
- Enable sleeping to save power.
- Add interrupt support for bmp3xx and bmp5xx devices. Also update bmp085
to new approach.
- Enable data ready trigger.
bosch,bmi270
- Add triggered buffer support
- Add scale and sampling frequency control.
vishay,veml6070
- Support integration time via DT binding for an external resistor value.
Cleanup and minor fixes
=======================
core
- Fix a longstanding issue with event codes for differential channels.
Note that not all drivers are yet fixed, but macros have been added
to avoid potential repeats of this in future.
- Tidy up handling in iio_read_acpi_mount matrix.
- Mark iio_dev::priv with __private. Later move the marking before the
field name to avoid a kernel-doc issue.
treewide
- Drop some pointless default n entries in Kconfig.
- Add an iio_get_acpi_device_name_and_data() handler to replace some
commonly repeated code.
- simplify use of 'state' in write_event_config() callback as it is
effectively a boolean. Once done make it a boolean (lots of drivers
were updated to enable this)
- some more use of devm_regulator_get_enable_read_voltage( to replace
open coded versions. Where this enables it convert all of remove
handling to devm based and drop the remove callback.
- check returns from devm_mutex_init()
accel drivers
- Use aligned_s64 instead of s64 __aligned(8)
adi,ad5791
- Add some missing GPIOs and power supplies that presumably were always
hard wired on previous boards.
- Refactor to use chip_info in device id tables.
- Convert probe entirely to devm based simplify code and allowing remove()
callback to be dropped.
adi,ad7192
- Check return from spi_get_device_match_data()
adi,ad74413r
- Don't keep an unnecessary copy of the gpio after probe.
- Use devm_regulator_get_enable_read_voltage() instead of open coding.
- Apply cleanup.h approach to reduce complexity.
adi,dac8460
- Fix a wrong compaitble ID due to a stray space.
- Add an spi_device_id table.
bosch,bmc150
- Drop some likely false ACPI IDs.
- Drop left over unused ACPI specific code.
bosch,bme680
- Add mising regmap.h include.
- Reduce excessive sleep on startup.
- Drop some cammelcase usage.
- Use fsleep
- Generalize read functions to allow for reuse.
- Use s16 variable to avoid some incorrect casting
bosch,bmg150
- Drop some likely false ACPI IDs.
bosch,bmi270
- Drop unused FREQUENCY and SCALE attributes that always returned an
error (they wil be back impelmented correctly).
- Factor out the chip specific data into a structure to enable simple
support for additional devices.
isil,isl29018
- Drop ACPI_PTR() and CONFIG_ACPI guards as not worth the trouble for very
minor saving.
invensense,mpu6050
- Use much simpler test for ACPI firmware.
kionix,kxcjk-1013
- Drop unnecessary ACPI entry in the i2c_device_id table.
- Drop support KX022-1020 to fix a bug that was introduced with that change.
Hopefully a fixed version will replace it soon.
- Drop CONFIG guards for PM in favor of pm_ptr() and the compiler removing
dead code.
- Switch from enum to chip_info structure and add ODR times to that structure.
- Deduplicate one of those ODR structures
- Drop ACPI_PTR() and move ID table out of config guards.
- Minor additional cleanup.
liteon,ltr401
- Drop some likely false ACPI Ids and add LTER0303 which is know to be in use.
microchip,pac1934
- Use much simpler test for ACPI firmware.
vishay,veml6070
- Use unsigned int instead of just unsigned.
- Use FIELD_PREP to make setting of field value explicit.
Various other minor fixes to documentation
* tag 'iio-for-6.13b' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (153 commits)
iio: Move __private marking before struct element priv in struct iio_dev
docs: iio: ad7380: add adaq4370-4 and adaq4380-4
iio: adc: ad7380: add support for adaq4370-4 and adaq4380-4
iio: adc: ad7380: use local dev variable to shorten long lines
iio: adc: ad7380: fix oversampling formula
dt-bindings: iio: adc: ad7380: add adaq4370-4 and adaq4380-4 compatible parts
iio: chemical: bme680: Add support for preheat current
iio: chemical: bme680: Add triggered buffer support
iio: chemical: bme680: Add SCALE and RAW channels
iio: chemical: bme680: refactorize set_mode() mode
iio: events: make IIO_EVENT_CODE macro private
iio: accel: mma9553: use specialized event code macros
iio: dummy: use specialized event code macros
iio: adc: ad7280a: use IIO_DIFF_EVENT_CODE macro helper
iio: events.h: add event identifier macros for differential channel
iio: magnetometer: add Allegro MicroSystems ALS31300 3-D Linear Hall Effect driver
dt-bindings: iio: magnetometer: document the Allegro MicroSystems ALS31300 3-D Linear Hall Effect Sensor
dt-bindings: vendor-prefixes: Add Allegro MicroSystems, Inc
iio: light: apds9960: remove useless return
iio: light: apds9960: convert als_int and pxs_int to bool
...
Even if it's not critical, the avoidance of checking the error code
from devm_mutex_init() call today diminishes the point of using devm
variant of it. Tomorrow it may even leak something. Add the missed
check.
Fixes: 938fd562b9 ("iio: adc: Add support for AD4000")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20241030162013.2100253-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix reading unsigned data from the AD4000 ADC via the _raw sysfs
attribute by ensuring that *val is set before returning from
ad4000_single_conversion(). This was not being set in any code path
and was causing the attribute to return a random value.
Fixes: 938fd562b9 ("iio: adc: Add support for AD4000")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20241030-iio-adc-ad4000-fix-reading-unsigned-data-v1-1-2e28dd75fe29@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for AD4000 series of low noise, low power, high speed,
successive approximation register (SAR) ADCs.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/356109ac61182f16f2379d5d0cadccfe017f505b.1720810545.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
