LKP found a random config which failed to build because IO accessors
were not defined:
In file included from drivers/i3c/master.c:21:
drivers/i3c/internals.h: In function 'i3c_writel_fifo':
>> drivers/i3c/internals.h:35:9: error: implicit declaration of function 'writesl' [-Werror=implicit-function-declaration]
Add the proper header to where the IO accessors are used.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507150208.BZDzzJ5E-lkp@intel.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250717120046.9022-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20250704075417.3218742-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
pm_runtime_put_autosuspend(), pm_runtime_put_sync_autosuspend(),
pm_runtime_autosuspend() and pm_request_autosuspend() now include a call
to pm_runtime_mark_last_busy(). Remove the now-reduntant explicit call to
pm_runtime_mark_last_busy().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250704075416.3218647-1-sakari.ailus@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In a private write transfer, the driver pre-fills the FIFO to work around
the FIFO_EMPTY quirk. However, if an IBIWON event occurs, the hardware
emits a NACK and the driver initiates a retry. During the retry, driver
attempts to pre-fill the FIFO again if there is remaining data, but since
the FIFO is already full, this leads to data loss.
Check available space in FIFO to prevent overflow.
Fixes: 4008a74e0f ("i3c: master: svc: Fix npcm845 FIFO empty issue")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250730003719.1825593-1-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a basic driver for the I3C controller found in Renesas RZ/G3S and
G3E SoCs. Support I3C pure busses (tested with two targets) and mixed
busses (two I3C devices plus various I2C targets). DAA and communication
with temperature sensors worked reliably at various speeds.
Missing features such as IBI, HotJoin, and target mode will be added
incrementally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Align existing defines to follow the consistent pattern:
I3C_BUS_<PARAM>_<MAX|MIN|TYP>_<UNIT>. Prepare the codebase for adding
new parameters and help avoid duplication.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Tommaso Merciai <tommaso.merciai.xr@bp.renesas.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250724094146.6443-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The two clocks, driver is getting, are not being disabled/re-enabled
during runtime of the device. Eliminate one variable in state struct,
all error paths and a lot of code from probe() and remove() by using
devm_clk_get_enabled().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250713152411.74917-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Sphinx reports indentation warning on i3c_device_do_priv_xfers() return
value list:
Documentation/driver-api/i3c/device-driver-api:9: ./drivers/i3c/device.c:31: ERROR: Unexpected indentation. [docutils]
Format the list as bullet list to fix the warning.
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250702040424.18577-1-bagasdotme@gmail.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-3-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use common inline i3c_writel_fifo()/i3c_readl_fifo() methods to
simplify code since the FIFO of controller is a 32bit width.
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-2-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The I3C abstraction expects u8 buffers, but some controllers operate with
a 32-bit bus width FIFO and cannot flag valid bytes individually. To avoid
reading or writing outside the buffer bounds, use 32-bit accesses where
possible and apply memcpy for any remaining bytes
Signed-off-by: Jorge Marques <jorge.marques@analog.com>
Suggested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250624-i3c-writesl-readsl-v3-1-63ccf0870f01@analog.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Hexadecimal values in sysfs should be prefixed with '0x' like e.g. PCI
and SCSI already do it. Also ensure the two digit length since BCR and
DCR are a byte in size.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250707115409.73545-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-8-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-7-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace non-standard ENOTSUPP with the SUSV4-defined error code
EOPNOTSUPP to fix below checkpatch warning:
"ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250628192027.3932-6-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
'I3C_BCR_HDR_CAP' is still spec v1.0 and has been renamed to 'advanced
capabilities' in v1.1 onwards. The ST pressure sensor LPS22DF does not
have HDR, but has the 'advanced cap' bit set. The core still wants to
get additional information using the CCC 'GETHDRCAP' (or GETCAPS in v1.1
onwards). Not all controllers support this CCC and will notify the upper
layers about it. For instantiating the device, we can ignore this
unsupported CCC as standard communication will work. Without this patch,
the device will not be instantiated at all.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250704204524.6124-1-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-4-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-3-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I2C adapters have their own timeout value which can be changed by
userspace if desired. Use it for I2C transfers. The default is 1Hz, so
the default behaviour is unchanged.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250604101831.56585-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Kconfig file for controller drivers is only sourced if the I3C
symbol is enabled. No need to check for that in individual drivers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250506075247.1545-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the clk_bulk API to handle clocks, so the code can support different
numbers of clocks more easily. Make the code cleaner and more flexible.
No change in functionality.
Signed-off-by: Carlos Song <carlos.song@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250427083230.3325700-3-carlos.song@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
According to the I3C specification, address arbitration only happens during
the START. Repeated START do not initiate arbitration, and In-Band
Interrupts (IBIs) cannot occur at this stage.
Resending the address upon a NACK in a repeat START is therefore redundant
and unnecessary. Avoid redundant retries, improving efficiency and ensuring
protocol compliance.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250429054234.4013929-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Queuing the IBI request does not need to be done earlier than emitting
the STOP. Emitting STOP immediately after receiving the IBI request can
complete the IBI transaction earlier and return the bus to idle.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250415051808.88091-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Moving the job from workqueue to ISR for two reasons.
1. Improve bus utilization.
If the requests are postponed to be received in the workqueue thread,
the SDA line remains low for a long time while the system loading is
high. During this period, the bus is not available for other targets
to raise requests.
2. Ensure prompt response to requests.
For timing-critical requests, the target may encouter a failure or the
event is missed if the request is not received in time.
IBI request is short, ISR can receive the data quickly and then queue a
work to handle it in the bottom half.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250415051808.88091-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Move "unexpected INTR_STATUS" error print before calling the IO handler
as it is more consistent that way. Otherwise it may be confusing if
generic interrupt related prints are mixed with IO handler prints.
Since this error print is more indication of missing code rather than
runtime error downgrade it to dev_warn_once().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-5-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
INTR_STATUS bit 11 INTR_HC_RESET_CANCEL was probably projected for the
MIPI I3C HCI specification version 2 but was not ever implemented.
This bit is first time specified in the v1.2 as HC_SEQ_CANCEL_STAT
"Host Controller Cancelled Transaction Sequence". Update the definition
and debug print of it accordingly.
While at it, change DBG() print to dev_dbg().
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-4-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Status fields in INTR_STATUS register are write 1 to clear so do it
unconditionally and move clearing of them out of an if block.
Suggested-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250409140401.299251-3-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Return IRQ_HANDLED from the i3c_hci_irq_handler() only if some
INTR_STATUS bit was set or if DMA/PIO handler handled it.
Currently it returns IRQ_HANDLED in case INTR_STATUS is zero and IO
handler returns false. Which could be the case if interrupt comes from
other device or is spurious.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250409140401.299251-2-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Since MIPI I3C HCI specification version v0.8 INTR_STATUS bits 9:0 are
reserved. Version v0.5 has bits 9 and 5:0 in use but not handled by the
current driver code and not needed in DMA transfers.
PIO transfers with v0.5 would require changes to both
core.c: i3c_hci_irq_handler() and pio.c: hci_pio_irq_handler() though.
For these reasons don't enable signal updates from INTR_STATUS bits 9:0.
It allow to get rid of "unexpected INTR_STATUS" error messages on old
v0.5 IP version and is a no-op for later versions starting from v0.8.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250409140401.299251-1-jarkko.nikula@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The I3C master driver may receive an IBI from a target device that has not
been probed yet. In such cases, the master calls `i3c_master_queue_ibi()`
to queue an IBI work task, leading to "Unable to handle kernel read from
unreadable memory" and resulting in a kernel panic.
Typical IBI handling flow:
1. The I3C master scans target devices and probes their respective drivers.
2. The target device driver calls `i3c_device_request_ibi()` to enable IBI
and assigns `dev->ibi = ibi`.
3. The I3C master receives an IBI from the target device and calls
`i3c_master_queue_ibi()` to queue the target device driver’s IBI
handler task.
However, since target device events are asynchronous to the I3C probe
sequence, step 3 may occur before step 2, causing `dev->ibi` to be `NULL`,
leading to a kernel panic.
Add a NULL pointer check in `i3c_master_queue_ibi()` to prevent accessing
an uninitialized `dev->ibi`, ensuring stability.
Fixes: 3a379bbcea ("i3c: Add core I3C infrastructure")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/lkml/Z9gjGYudiYyl3bSe@lizhi-Precision-Tower-5810/
Signed-off-by: Manjunatha Venkatesh <manjunatha.venkatesh@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250326123047.2797946-1-manjunatha.venkatesh@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
OF APIs are usually NULL-aware and returns an error in case when
device node is not present or supported. We already have a check
for the returned value, no need to check for the parameter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250321193044.457649-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Clang warns (or errors with CONFIG_WERROR=y):
drivers/i3c/master/svc-i3c-master.c:596:2: error: unannotated fall-through between switch labels [-Werror,-Wimplicit-fallthrough]
596 | default:
| ^
drivers/i3c/master/svc-i3c-master.c:596:2: note: insert 'break;' to avoid fall-through
596 | default:
| ^
| break;
1 error generated.
Clang is a little more pedantic than GCC, which does not warn when
falling through to a case that is just break or return. Clang's version
is more in line with the kernel's own stance in deprecated.rst, which
states that all switch/case blocks must end in either break,
fallthrough, continue, goto, or return. Add the missing break to silence
the warning.
Fixes: 0430bf9bc1 ("i3c: master: svc: Fix missing STOP for master request")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20250319-i3c-fix-clang-fallthrough-v1-1-d8e02be1ef5c@kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The controller driver nacked the master request but didn't emit a
STOP to end the transaction. The driver shall refuse the unsupported
requests and return the controller state to IDLE by emitting a STOP.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-4-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The target can send the MDB byte followed by additional data bytes.
The readl on MRDATAB reads one actual byte, but the readsl advances
the destination pointer by 4 bytes. This causes the subsequent payload
to be copied to wrong position in the destination buffer.
Cc: stable@kernel.org
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The code does not add IBI rules for devices with controller capability.
However, the secondary controller has the controller capability and works
at target mode when the device is probed. Therefore, add IBI rules for
such devices.
Fixes: dd3c52846d ("i3c: master: svc: Add Silvaco I3C master driver")
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250318053606.3087121-2-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The return value of i3c_master_get_free_addr is assigned to a variable
with wrong type, so it can't be negative. Use a signed integer for the
return value. If the value is negative, break the process and propagate
the error code.
This commit also fixes the uninitialized symbol 'dyn_addr', reported
by Smatch static checker.
Fixes: 4008a74e0f ("i3c: master: svc: Fix npcm845 FIFO empty issue")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/029e5ac0-5444-4a8e-bca4-cec55950d2b9@stanley.mountain/
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250310023304.2335792-1-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When MCONFIG.SKEW=0 and MCONFIG.ODHPP=0, the ENTDAA transaction gets
corrupted and results in a no repeated-start condition at the end of
address assignment.
Workaround: Set MCONFIG.SKEW to 1 before initiating the DAA process.
After the DAA process is completed, return MCONFIG.SKEW to its previous
value.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250306075429.2265183-6-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C HW may generate an invalid SlvStart event when emitting a STOP.
If it is a true SlvStart, the MSTATUS state is SLVREQ. Check the
MSTATUS state to ignore the false event.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250306075429.2265183-5-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
I3C HW stalls the write transfer if the transmit FIFO becomes empty,
when new data is written to FIFO, I3C HW resumes the transfer but the
first transmitted data bit may have the wrong value.
Fill the FIFO in advance to prevent FIFO from becoming empty.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Link: https://lore.kernel.org/r/20250306075429.2265183-4-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Nuvoton npcm845 SoC uses an older IP version, which has specific
hardware issues that need to be addressed with a different compatible
string.
Add driver data for different compatible strings to define platform
specific quirks.
Add compatible string for npcm845 to define its own driver data.
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20250306075429.2265183-3-yschu@nuvoton.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Ensure the FIFO is empty before issuing the DAA command to prevent
incorrect command data from being sent. Align with other data transfers,
such as svc_i3c_master_start_xfer_locked(), which flushes the FIFO before
sending a command.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250129162250.3629189-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the i2c_get/put_dma_safe_msg_buf for I2C transfers instead of using
the I3C-specific API.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250204091702.4014466-2-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The change is necessary to enable the use of the
`i2c_get_dma_safe_msg_buf()` API, which requires a non-const
`struct i2c_msg *` to operate. The `i2c_get_dma_safe_msg_buf()` function
ensures safe handling of I2C messages when using DMA, making it essential
for scenarios where DMA transfers are involved. By removing the `const`
qualifier, this patch allows drivers to prepare and manage DMA-safe
buffers directly.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250204091702.4014466-1-billy_tsai@aspeedtech.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Core:
- Improve initialization of numbered I2C adapters
Drivers:
- use parity8 helper
- dw: fix possible use-after-free
- mipi-i3c-hci: add support for PCI bus host
- svc: many fixes for IBI and hotjoin
-----BEGIN PGP SIGNATURE-----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=esI9
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Alexandre Belloni:
"The main change is the addition of PCI bus support for mipi-i3c-hci.
I'm also carrying an hwmon patch as it makes use of the bitops
addition that is then mainly used by i3c drivers.
Core:
- Improve initialization of numbered I2C adapters
Drivers:
- use parity8 helper
- dw: fix possible use-after-free
- mipi-i3c-hci: add support for PCI bus host
- svc: many fixes for IBI and hotjoin"
* tag 'i3c/for-6.14' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: Improve initialization of numbered I2C adapters
i3c: master: Fix missing 'ret' assignment in set_speed()
i3c: cdns: use parity8 helper instead of open coding it
i3c: mipi-i3c-hci: use parity8 helper instead of open coding it
i3c: dw: use parity8 helper instead of open coding it
hwmon: (spd5118) Use generic parity calculation
bitops: add generic parity calculation for u8
i3c: mipi-i3c-hci: Add support for MIPI I3C HCI on PCI bus
i3c: mipi-i3c-hci: Add Intel specific quirk to ring resuming
i3c: fix kdoc parameter description for module_i3c_i2c_driver()
i3c: dw: Fix use-after-free in dw_i3c_master driver due to race condition
Add logic to initialize I2C adapters with a specific ID if available,
improving device identification and configuration.
For mixed buses, in addition to the i3c alias, an i2c alias can be added to
assign a fixed bus number to the i2c adapter.
This allows an alias node such as:
aliases {
i2c2 = &mixed_bus_a,
i3c2 = &mixed_bus_a,
i3c4 = &mixed_bus_b,
};
/* assigned "i3c-2" and "i2c-2" */
mixed_bus_a: i3c-master {
};
If there is no i2c alias for a mixed bus, the i2c adapter numbers will
remain as is and will be assigned starting after the highest fixed bus
number.
/* assigned "i3c-4" and likely assigned "i2c-3" */
mixed_bus_b: i3c-master {
};
Signed-off-by: Defa Li <defa.li@mediatek.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241212091818.8591-1-defa.li@mediatek.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix a probe failure in the i3c master driver that occurs when no i3c
devices are connected to the bus.
The issue arises in `i3c_master_bus_init()` where the `ret` value is not
updated after calling `master->ops->set_speed()`. If no devices are
present, `ret` remains set to `I3C_ERROR_M2`, causing the code to
incorrectly proceed to `err_bus_cleanup`.
Cc: stable@vger.kernel.org
Fixes: aef79e189b ("i3c: master: support to adjust first broadcast address speed")
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20250108225533.915334-1-Frank.Li@nxp.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The kernel has now a generic helper for getting parity with easier to
understand semantics. Make use of it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20250107090204.6593-6-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The kernel has now a generic helper for getting parity with easier to
understand semantics. Make use of it. Here, it also fixes a bug because
the correct algorithm is using XOR ('^=') instead of ADD ('+=').
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20250107090204.6593-5-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
