Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:
ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched. Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659616/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-6-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add phy configuration for 28nm dsi phy found on MSM8937 SoC. Only
difference from existing msm8916 configuration is number of phy
and io_start addresses.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600518/
Link: https://lore.kernel.org/r/20240623-dsi-v2-4-a0ca70fb4846@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This helper has been introduced to avoid programmer errors (missing
_put calls leading to dangling refcnt) when using pm_runtime_get, use it.
While at it, start checking the return value.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: 5c82902844 ("drm/msm/dsi: Split PHY drivers to separate files")
Patchwork: https://patchwork.freedesktop.org/patch/543350/
Link: https://lore.kernel.org/r/20230620-topic-dsiphy_rpm-v2-1-a11a751f34f0@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
SM6125 features only a single PHY (despite a secondary PHY PLL source
being available to the disp_cc_mdss_pclk0_clk_src clock), and downstream
sources for this "trinket" SoC do not define the typical "vcca"
regulator to be available nor used. This, including the register offset
is identical to QCM2290, whose config struct can trivially be reused.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/548980/
Link: https://lore.kernel.org/r/20230723-sm6125-dpu-v4-13-a3f287dd6c07@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MSM8226 uses a modified PLL lock sequence compared to MSM8974, which is
based on the function dsi_pll_enable_seq_m in the msm-3.10 kernel.
Worth noting that the msm-3.10 downstream kernel also will try other
sequences in case this one doesn't work, but during testing it has shown
that the _m sequence succeeds first time also:
.pll_enable_seqs[0] = dsi_pll_enable_seq_m,
.pll_enable_seqs[1] = dsi_pll_enable_seq_m,
.pll_enable_seqs[2] = dsi_pll_enable_seq_d,
.pll_enable_seqs[3] = dsi_pll_enable_seq_d,
.pll_enable_seqs[4] = dsi_pll_enable_seq_f1,
.pll_enable_seqs[5] = dsi_pll_enable_seq_c,
.pll_enable_seqs[6] = dsi_pll_enable_seq_e,
We may need to expand this in the future.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/540618/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-6-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the vendor kernel, byte intf clock rate should be a half of
the byte clock only when DSI PHY version is above 2.0 (in other words,
10nm PHYs and later) and only if PHY is used in D-PHY mode. Currently
MSM DSI code handles only the second part of the clause (C-PHY vs
D-PHY), skipping DSI PHY version check, which causes issues on some of
14nm DSI PHY platforms (e.g. qcm2290).
Move divisor selection to DSI PHY code, pass selected divisor through
shared timings and set byte intf clock rate accordingly.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM6115P J606F
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519006/
Link: https://lore.kernel.org/r/20230118130027.2345719-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The QCM2290 SoC a the 14nm (V2.0) single DSI phy. The platform is not
fully compatible with the standard 14nm PHY, so it requires a separate
compatible and config entry.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[DB: rebased and updated commit msg]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/504578/
Link: https://lore.kernel.org/r/20220924121900.222711-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The dsi_phy_driver_probe() function has a "goto fail" for no
reason. Change it to just always return directly when it sees an
error. Make this simpler by leveraging dev_err_probe() which is
designed to make code like this shorter / simpler.
NOTE: as part of this, we now pass through error codes directly from
msm_ioremap_size() rather than translating to -ENOMEM. This changed
mostly because it's much more convenient when using dev_err_probe()
and also it's usually encouraged not to hide error codes like the old
code was doing unless there is a good reason. I can't see any reason
why we'd need to return -ENOMEM instead of -EINVAL from the probe
function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496324/
Link: https://lore.kernel.org/r/20220804073608.v4.6.I969118a35934a0e5007fe4f80e3e28e9c0b7602a@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 6eabfc018e ("regulator: core: Allow specifying an
initial load w/ the bulk API") we can now specify the initial load in
the bulk data rather than having to manually call regulator_set_load()
on each regulator. Let's use it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496319/
Link: https://lore.kernel.org/r/20220804073608.v4.4.I7b3c72949883846badb073cfeae985c55239da1d@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add support for MSM DSI PHY tuning configuration. Current design is
to support drive strength and drive level/amplitude tuning for
10nm PHY version, but this can be extended to other PHY versions.
Signed-off-by: Rajeev Nandan <quic_rajeevny@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/1643573719-32095-3-git-send-email-quic_rajeevny@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
msm_ioremap() functions take additional argument dbgname which is now
unused.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20220105232700.444170-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The function performs a check on the "phy" input parameter, however, it
is used before the check.
Initialize the "dev" variable after the sanity check to avoid a possible
NULL pointer dereference.
Fixes: 5c82902844 ("drm/msm/dsi: Split PHY drivers to separate files")
Addresses-Coverity-ID: 1493860 ("Null pointer dereference")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20220116181844.7400-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
No functional change, as we only actually enable autosuspend for the GPU
device. But lets not encourage thinking that autosuspend is a good idea
for anything display related.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211215175910.1744151-1-robdclark@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no reason to set clock parents manually, use device tree to
assign DSI/display clock parents to DSI PHY clocks. Dropping this manual
setup allows us to drop repeating code and to move registration of hw
clock providers to generic place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211006204828.1218225-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add phy configuration for 14nm dsi phy found on MSM8953 SoC. Only
difference from existing configurations are io_start addresses.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sireesh Kodali <sireeshkodali1@gmail.com>
Link: https://lore.kernel.org/r/20210928131929.18567-3-sireeshkodali1@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Unlike previous generations, 7nm PHYs are required to collaborate with
the host for continuos clock mode. Add changes neccessary to enable
continuous clock mode in the 7nm DSI PHYs.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210805170817.3337665-1-dmitry.baryshkov@linaro.org
[Fix merge conflict, and $description typo]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of fetching shared timing through an extra function call, get
them directly from msm_dsi_phy_enable.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210709210729.953114-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add the required changes to support 7nm pll/phy in CPHY mode.
This adds a "qcom,dsi-phy-cphy-mode" property for the PHY node to enable
the CPHY mode.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210617144349.28448-4-jonathan@marek.ca
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add DSI PHY registers to the msm state snapshots to be able to check
their contents.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210427001828.2375555-5-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_dsi_phy_get_clk_provider() always returns two provided clocks, so
return 0 instead of returning incorrect -EINVAL error code.
Fixes: 5d13459650 ("drm/msm/dsi: push provided clocks handling into a generic code")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Jonathan Marek <jonathan@marek.ca>
Link: https://lore.kernel.org/r/20210412000158.2049066-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-25-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
The src_truthtable config is not used for some of phys, which use other
means of configuring the master/slave usecases. Inline this function
with the goal of removing src_pll_id argument in the next commit.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-24-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All PHY drivers would map dsi_pll area. Some PHY drivers would also
map dsi_phy area again (a leftover from old PHY/PLL separation). Move
all ioremaps to the common dsi_phy driver code and drop individual
ioremapped areas from PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-21-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Make save_state/restore callbacks accept struct msm_dsi_phy rather than
struct msm_dsi_pll. This moves them to struct msm_dsi_phy_ops, allowing
us to drop struct msm_dsi_pll_ops.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-18-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Morph msm_dsi_pll_save/restore_state() into msm_dsi_phy_save/restore_state(),
thus removing last bits of knowledge about msm_dsi_pll from dsi_manager.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-14-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devm_of_clk_add_hw_provider() to register provided clocks. This
allows dropping the remove function alltogether.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-13-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devres-enabled version of clock registration functions. This lets us
remove dsi_pll destroy callbacks completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-12-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all PLL-related callbacks into struct msm_dsi_phy_cfg. This limits
the amount of data in the struct msm_dsi_pll.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-7-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
DSI PHY init callback would either map dsi_phy_regulator or dsi_phy_lane
depending on the PHY type. Replace those callbacks with configuration
options governing mapping those regions.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-4-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.
Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
These SoCs make use of the 14nm phy, but at different
addresses than other 14nm units.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Save pll state before dsi host is powered off. Without this change
some register values gets resetted.
Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The 28nm PLL has a different iospace on MSM/APQ family B SoCs:
add a new configuration and use it when the DT reports the
"qcom,dsi-phy-28nm-hpm-fam-b" compatible.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v2:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:156:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c: In function msm_dsi_dphy_timing_calc_v3:
drivers/gpu/drm/msm/dsi/phy/dsi_phy.c:273:17: warning: variable lpx set but not used [-Wunused-but-set-variable]
'lpx' in msm_dsi_dphy_timing_calc_v2 is not used since commit a4df68fa23
("drm/msm/dsi: Add new method to calculate 14nm PHY timings")
'lpx' in msm_dsi_dphy_timing_calc_v3 is not used since commit f1fa7ff440
("drm/msm/dsi: implement auto PHY timing calculator for 10nm PHY")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1570690506-83287-4-git-send-email-zhengbin13@huawei.com
The following errors show up when booting the Nexus 5:
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_regulator_init: failed to init regulator, ret=-517
msm_dsi_phy fd922a00.dsi-phy: [drm:dsi_phy_driver_probe] *ERROR*
dsi_phy_driver_probe: failed to init regulator
dsi_phy_regulator_init() already logs the error, so no need to log
the same error a second time in dsi_phy_driver_probe(). This patch
also changes dsi_phy_regulator_init() to not log the error if the
error code is -EPROBE_DEFER to reduce noise in dmesg.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[add some {}'s]
Signed-off-by: Rob Clark <robdclark@chromium.org>
