Data for HDMI, DSI and DP blocks only makes sense for the KMS parts of
the driver. Move corresponding data pointers from struct msm_drm_private
to struct msm_kms.
Suggested-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/662580/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Most of the driver code doesn't need to reach in to msm specific fields,
so just use the drm_gpuvm/drm_gpuva types directly. This should
hopefully improve commonality with other drivers and make the code
easier to understand.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661483/
Re-aligning naming to better match drm_gpuvm terminology will make
things less confusing at the end of the drm_gpuvm conversion.
This is just rename churn, no functional change.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661466/
Add support for DSI on Qualcomm SM8750 SoC with notable difference:
DSI PHY PLLs, the parents of pixel and byte clocks, cannot be used as
parents before DSI PHY is configured, the PLLs are prepared and their
initial rate is set. Therefore assigned-clock-parents are not working
here and driver is responsible for reparenting clocks with proper
procedure: see dsi_clk_init_6g_v2_9().
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659619/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-7-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Add support for DSI PHY v7.0 on Qualcomm SM8750 SoC which comes with an
incompatible hardware interface change:
ICODE_ACCUM_STATUS_LOW and ALOG_OBSV_BUS_STATUS_1 registers - their
offsets were just switched. Currently these registers are not used in
the driver, so the easiest is to document both but keep them commented
out to avoid conflict.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/659616/
Link: https://lore.kernel.org/r/20250618-b4-sm8750-display-v7-6-a591c609743d@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Driver unconditionally saves current state on first init in
dsi_pll_10nm_init(), but does not save the VCO rate, only some of the
divider registers. The state is then restored during probe/enable via
msm_dsi_phy_enable() -> msm_dsi_phy_pll_restore_state() ->
dsi_10nm_pll_restore_state().
Restoring calls dsi_pll_10nm_vco_set_rate() with
pll_10nm->vco_current_rate=0, which basically overwrites existing rate of
VCO and messes with clock hierarchy, by setting frequency to 0 to clock
tree. This makes anyway little sense - VCO rate was not saved, so
should not be restored.
If PLL was not configured configure it to minimum rate to avoid glitches
and configuring entire in clock hierarchy to 0 Hz.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/sz4kbwy5nwsebgf64ia7uq4ee7wbsa5uy3xmlqwcstsbntzcov@ew3dcyjdzmi2/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: a4ccc37693 ("drm/msm/dsi_pll_10nm: restore VCO rate during
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/654796/
Link: https://lore.kernel.org/r/20250520111325.92352-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Newly added dsi_pll_cmn_clk_cfg1_update() wrapper protects concurrent
updates to PHY_CMN_CLK_CFG1 register between driver and Common Clock
Framework. pll_7nm_register() still used in one place previous
readl+writel, which can be simplified with this new wrapper.
This is purely for readability and simplification and should have no
functional impact, because the code touched here is before clock is
registered via CCF, so there is no concurrency issue.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/638323/
Link: https://lore.kernel.org/r/20250219-drm-msm-phy-pll-cfg-reg-v5-1-d28973fa513a@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The DRM DSC helper has various bits_per_component values - not just 8.
But the DSC 1.1 block supports only 8, 10, and 12. Extend the guard
accordingly and add a comment noting this limitation.
Signed-off-by: Eugene Lepshy <fekz115@gmail.com>
Co-developed-by: Danila Tikhonov <danila@jiaxyga.com>
Signed-off-by: Danila Tikhonov <danila@jiaxyga.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637831/
Link: https://lore.kernel.org/r/20250217222431.82522-4-danila@jiaxyga.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Ordering issues here cause an uninitialized (default STANDALONE)
usecase to be programmed (which appears to be a MUX) in some cases
when msm_dsi_host_register() is called, leading to the slave PLL in
bonded-DSI mode to source from a clock parent (dsi1vco) that is off.
This should seemingly not be a problem as the actual dispcc clocks from
DSI1 that are muxed in the clock tree of DSI0 are way further down, this
bit still seems to have an effect on them somehow and causes the right
side of the panel controlled by DSI1 to not function.
In an ideal world this code is refactored to no longer have such
error-prone calls "across subsystems", and instead model the "PLL src"
register field as a regular mux so that changing the clock parents
programmatically or in DTS via `assigned-clock-parents` has the
desired effect.
But for the avid reader, the clocks that we *are* muxing into DSI0's
tree are way further down, so if this bit turns out to be a simple mux
between dsiXvco and out_div, that shouldn't have any effect as this
whole tree is off anyway.
Fixes: 57bf433893 ("drm/msm/dsi: Pass down use case to PHY")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/637650/
Link: https://lore.kernel.org/r/20250217-drm-msm-initial-dualpipe-dsc-fixes-v3-2-913100d6103f@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When configuring the timing of DSI hosts (interfaces) in
dsi_timing_setup() all values written to registers are taking
bonded-mode into account by dividing the original mode width by 2
(half the data is sent over each of the two DSI hosts), but the full
width instead of the interface width is passed as hdisplay parameter to
dsi_update_dsc_timing().
Currently only msm_dsc_get_slices_per_intf() is called within
dsi_update_dsc_timing() with the `hdisplay` argument which clearly
documents that it wants the width of a single interface (which, again,
in bonded DSI mode is half the total width of the mode) resulting in all
subsequent values to be completely off.
However, as soon as we start to pass the halved hdisplay
into dsi_update_dsc_timing() we might as well discard
msm_dsc_get_slices_per_intf() since the value it calculates is already
available in dsc->slice_count which is per-interface by the current
design of MSM DPU/DSI implementations and their use of the DRM DSC
helpers.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/637648/
Link: https://lore.kernel.org/r/20250217-drm-msm-initial-dualpipe-dsc-fixes-v3-1-913100d6103f@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Kernel core already prints detailed report about memory allocation
failures, so drivers should not have their own error messages.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637308/
Link: https://lore.kernel.org/r/20250214-drm-msm-cleanups-v2-4-1bec50f37dc1@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dsi_get_config(), dsi_clk_init() and msm_dsi_host_init() are called only
from platform driver probe function, so using dev_err_probe() is both
appropriate and beneficial:
- Properly marks device deferred probe status,
- Avoids dmesg flood on probe deferrals,
- Already incorporates printing ERR value,
- Shows device name (in contrast to pr_err()),
- Makes code smaller and simpler.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637306/
Link: https://lore.kernel.org/r/20250214-drm-msm-cleanups-v2-2-1bec50f37dc1@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dsi_clk_init(), which gets the clocks, is called only through platform
driver probe and its failure is a failure of the probe. Therefore
NULL-ifying specific clocks is pointless and redundant - the PTR_ERR
value stored there won't be used/dereferenced afterwards. What's more,
variant-specific clock init calls like dsi_clk_init_6g_v2() are not
doing this cleanup. Dropping redundant code allows later to make this a
bit simpler.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637303/
Link: https://lore.kernel.org/r/20250214-drm-msm-cleanups-v2-1-1bec50f37dc1@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Since SM8250 all downstream sources program clock inverters in
PLL_CLOCK_INVERTERS_1 register and leave the PLL_CLOCK_INVERTERS as
reset value (0x0). The most recent Hardware Programming Guide for 3 nm,
4 nm, 5 nm and 7 nm PHYs also mention PLL_CLOCK_INVERTERS_1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/634489/
Link: https://lore.kernel.org/r/20250129115504.40080-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes for v6.14-rc4
Display:
* More catalog fixes:
- to skip watchdog programming through top block if its not present
- fix the setting of WB mask to ensure the WB input control is programmed
correctly through ping-pong
- drop lm_pair for sm6150 as that chipset does not have any 3dmerge block
* Fix the mode validation logic for DP/eDP to account for widebus (2ppc)
to allow high clock resolutions
* Fix to disable dither during encoder disable as otherwise this was
causing kms_writeback failure due to resource sharing between
* WB and DSI paths as DSI uses dither but WB does not
* Fixes for virtual planes, namely to drop extraneous return and fix
uninitialized variables
* Fix to avoid spill-over of DSC encoder block bits when programming
the bits-per-component
* Fixes in the DSI PHY to protect against concurrent access of
PHY_CMN_CLK_CFG regs between clock and display drivers
Core/GPU:
* Fix non-blocking fence wait incorrectly rounding up to 1 jiffy timeout
* Only print GMU fw version once, instead of each time the GPU resumes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtt2AODBXdod8ULXcAygf_qYvwRDVeUVtODx=2jErp6cA@mail.gmail.com
PHY_CMN_CLK_CFG1 register has four fields being used in the driver: DSI
clock divider, source of bitclk and two for enabling the DSI PHY PLL
clocks.
dsi_7nm_set_usecase() sets only the source of bitclk, so should leave
all other bits untouched. Use newly introduced
dsi_pll_cmn_clk_cfg1_update() to update respective bits without
overwriting the rest.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637380/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-3-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG1 register is updated by the PHY driver and by a mux
clock from Common Clock Framework:
devm_clk_hw_register_mux_parent_hws(). There could be a path leading to
concurrent and conflicting updates between PHY driver and clock
framework, e.g. changing the mux and enabling PLL clocks.
Add dedicated spinlock to be sure all PHY_CMN_CLK_CFG1 updates are
synchronized.
While shuffling the code, define and use PHY_CMN_CLK_CFG1 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/637378/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-2-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
PHY_CMN_CLK_CFG0 register is updated by the PHY driver and by two
divider clocks from Common Clock Framework:
devm_clk_hw_register_divider_parent_hw(). Concurrent access by the
clocks side is protected with spinlock, however driver's side in
restoring state is not. Restoring state is called from
msm_dsi_phy_enable(), so there could be a path leading to concurrent and
conflicting updates with clock framework.
Add missing lock usage on the PHY driver side, encapsulated in its own
function so the code will be still readable.
While shuffling the code, define and use PHY_CMN_CLK_CFG0 bitfields to
make the code more readable and obvious.
Fixes: 1ef7c99d14 ("drm/msm/dsi: add support for 7nm DSI PHY/PLL")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/637376/
Link: https://lore.kernel.org/r/20250214-drm-msm-phy-pll-cfg-reg-v3-1-0943b850722c@linaro.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Updates for v6.14
MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
MDP4:
- several small fixes
DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- fixed modes filtering for platforms w/o 3DMux
- fixed DSPP DSPP_2 / _3 links on several platforms
- corrected DSPP definitions on SDM670
- added CWB hardware blocks support
- added VBIF to DPU snapshots
- dropped struct dpu_rm_requirements
DP:
- reworked DP audio support
DSI:
- added SM6150 (aka QCS615) support
GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com
The use of of_property_read_bool() for non-boolean properties is
deprecated in favor of of_property_present() when testing for property
presence.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241104190636.274926-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When (mode->clock * 1000) is larger than (1<<31), int to unsigned long
conversion will sign extend the int to 64 bits and the pclk_rate value
will be incorrect.
Fix this by making the result of the multiplication unsigned.
Note that above (1<<32) would still be broken and require more changes, but
its unlikely anyone will need that anytime soon.
Fixes: c4d8cfe516 ("drm/msm/dsi: add implementation for helper functions")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/618434/
Link: https://lore.kernel.org/r/20241007050157.26855-2-jonathan@marek.ca
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Add phy configuration for 28nm dsi phy found on MSM8937 SoC. Only
difference from existing msm8916 configuration is number of phy
and io_start addresses.
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/600518/
Link: https://lore.kernel.org/r/20240623-dsi-v2-4-a0ca70fb4846@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Allow board's device tree to specify the vsync source (aka TE source).
If the property is omitted, the display controller driver will use the
default setting.
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
[DB: fixed clearing of return value if there is no TE property]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/598740/
Link: https://lore.kernel.org/r/20240613-dpu-handle-te-signal-v2-6-67a0116b5366@linaro.org
Make it clear why the pkt_per_line value is being "divided by 2".
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596236/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-6-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Video mode DSC won't work if this field is not set correctly. Set it to fix
video mode DSC (for slice_per_pkt==1 cases at least).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/596234/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-5-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The value returned by msm_dsi_wide_bus_enabled() doesn't match what the
driver is doing in video mode. Fix that by actually enabling widebus for
video mode.
Fixes: efcbd6f9cd ("drm/msm/dsi: Enable widebus for DSI")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-HDK
Patchwork: https://patchwork.freedesktop.org/patch/596232/
Link: https://lore.kernel.org/r/20240530-msm-drm-dsc-dsi-video-upstream-4-v6-4-2ab1d334c657@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
When dual-DSI (bonded DSI) was added in commit ed9976a09b
("drm/msm/dsi: adjust dsi timing for dual dsi mode") some DBG() prints
were not updated, leading to print the original mode->clock rather
than the adjusted (typically the mode clock divided by two, though more
recently also adjusted for DSC compression) msm_host->pixel_clk_rate
which is passed to clk_set_rate() just below. Fix that by printing the
actual pixel_clk_rate that is being set.
Fixes: ed9976a09b ("drm/msm/dsi: adjust dsi timing for dual dsi mode")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/589896/
Link: https://lore.kernel.org/r/20240417-drm-msm-initial-dualpipe-dsc-fixes-v1-1-78ae3ee9a697@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently the MSM DSI driver looks for the next bridge during
msm_dsi_modeset_init(). If the bridge is not registered at that point,
this might result in -EPROBE_DEFER, which can be problematic that late
during the device probe process. Move next bridge acquisition to the
dsi_bind state so that probe deferral is returned as early as possible.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/582210/
Link: https://lore.kernel.org/r/20240309-fd-dsi-cleanup-bridges-v1-2-962ebdba82ed@linaro.org
