Now that Adreno specifics are out of the way, use the common config
(but leave the HBB hardcoding in place until that is wired up on the
other side).
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/660985/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Most of the driver code doesn't need to reach in to msm specific fields,
so just use the drm_gpuvm/drm_gpuva types directly. This should
hopefully improve commonality with other drivers and make the code
easier to understand.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661483/
It is standing in the way of drm_gpuvm / VM_BIND support. Not to
mention frequently broken and rarely tested. And I think only needed
for a 10yr old not quite upstream SoC (msm8974).
Maybe we can add support back in later, but I'm doubtful.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661467/
Re-aligning naming to better match drm_gpuvm terminology will make
things less confusing at the end of the drm_gpuvm conversion.
This is just rename churn, no functional change.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Tested-by: Antonino Maniscalco <antomani103@gmail.com>
Reviewed-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/661466/
When things go wrong, the GPU is capable of quickly generating millions
of faulting translation requests per second. When that happens, in the
stall-on-fault model each access will stall until it wins the race to
signal the fault and then the RESUME register is written. This slows
processing page faults to a crawl as the GPU can generate faults much
faster than the CPU can acknowledge them. It also means that all
available resources in the SMMU are saturated waiting for the stalled
transactions, so that other transactions such as transactions generated
by the GMU, which shares translation resources with the GPU, cannot
proceed. This causes a GMU watchdog timeout, which leads to a failed
reset because GX cannot collapse when there is a transaction pending and
a permanently hung GPU.
On older platforms with qcom,smmu-v2, it seems that when one transaction
is stalled subsequent faulting transactions are terminated, which avoids
this problem, but the MMU-500 follows the spec here.
To work around these problems, disable stall-on-fault as soon as we get a
page fault until a cooldown period after pagefaults stop. This allows
the GMU some guaranteed time to continue working. We only use
stall-on-fault to halt the GPU while we collect a devcoredump and we
always terminate the transaction afterward, so it's fine to miss some
subsequent page faults. We also keep it disabled so long as the current
devcoredump hasn't been deleted, because in that case we likely won't
capture another one if there's a fault.
After this commit HFI messages still occasionally time out, because the
crashdump handler doesn't run fast enough to let the GMU resume, but the
driver seems to recover from it. This will probably go away after the
HFI timeout is increased.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/654891/
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The call chain on a5xx_gpu_init is such that pdev is not going to be
null, so the null check on pdev can be removed. This also cleans up
a static analysis warning where pdev is dereferenced before the null
check which cannot actually occur.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Patchwork: https://patchwork.freedesktop.org/patch/624180/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This adds MSM_PARAM_UCHE_TRAP_BASE that will be used by Mesa
implementation for VK_KHR_shader_clock and GL_ARB_shader_clock.
Signed-off-by: Danylo Piliaiev <dpiliaiev@igalia.com>
Patchwork: https://patchwork.freedesktop.org/patch/627036/
Signed-off-by: Rob Clark <robdclark@chromium.org>
With preemption it is not enough to track the current_ctx_seqno globally
as execution might switch between rings.
This is especially problematic when current_ctx_seqno is used to
determine whether a page table switch is necessary as it might lead to
security bugs.
Track current context per ring.
Tested-by: Rob Clark <robdclark@gmail.com>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8650-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8450-HDK
Signed-off-by: Antonino Maniscalco <antomani103@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/618012/
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is another cause for soft lock-up of GPU in empty ring-buffer:
race between GPU executing last commands and CPU checking ring for
emptiness. On GPU side IRQ for retire is triggered by CACHE_FLUSH_TS
event and RPTR shadow (which is used to check ring emptiness) is updated
a bit later from CP_CONTEXT_SWITCH_YIELD. Thus if GPU is executing its
last commands slow enough or we check that ring too fast we will miss a
chance to trigger switch to lower priority ring because current ring isn't
empty just yet. This can escalate to lock-up situation described in
previous patch.
To work-around this issue we keep track of last submit sequence number
for each ring and compare it with one written to memptrs from GPU during
execution of CACHE_FLUSH_TS event.
Fixes: b1fc2839d2 ("drm/msm: Implement preemption for A5XX targets")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612047/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Fine grain preemption (switching from/to points within submits)
requires extra handling in command stream of those submits, especially
when rendering with tiling (using GMEM). However this handling is
missing at this point in mesa (and always was). For this reason we get
random GPU faults and hangs if more than one priority level is used
because local preemption is enabled prior to executing command stream
from submit.
With that said it was ahead of time to enable local preemption by
default considering the fact that even on downstream kernel it is only
enabled if requested via UAPI.
Fixes: a7a4c19c36 ("drm/msm/a5xx: fix setting of the CP_PREEMPT_ENABLE_LOCAL register")
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/612041/
Signed-off-by: Rob Clark <robdclark@chromium.org>
According to downstream we should be setting RBBM_NC_MODE_CNTL to a
non-default value on a663 and a680, we don't support a663 and on a680
we're leaving it at the wrong (suboptimal) value. Just set it on all
GPUs. Similarly, plumb through level2_swizzling_dis which will be
necessary on a663.
ubwc_mode is expanded and renamed to ubwc_swizzle to match the name on
the display side. Similarly macrotile_mode should match the display
side.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/607397/
Signed-off-by: Rob Clark <robdclark@chromium.org>
This GPU is found on SoCs such as MSM8937 (450 MHz), MSM8940 (475 MHz),
SDM439 (650 MHz).
Signed-off-by: Daniil Titov <daniilt971@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Barnabás Czémán <trabarni@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/601411/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Split up calculating configuration parameters and programming them, so
that we can expose them to userspace.
Signed-off-by: Connor Abbott <cwabbott0@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/571180/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Basically everywhere wants the base ptr type. So store that instead of
msm_gem_object.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/551021/
Since the revision becomes an opaque identifier with future GPUs, move
away from treating different ranges of bits as having a given meaning.
This means that we need to explicitly list different patch revisions in
the device table.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549782/
Even in the ocmem case, the allocated ocmem buffer size should match the
requested size.
v2: Move stray hunk to previous patch, make OCMEM size mismatch an error
condition.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/549759/
The msm_gem_get_vaddr() returns an ERR_PTR() on failure, and a null
is catastrophic here, so we should use IS_ERR_OR_NULL() to check
the return value.
Fixes: 6a8bd08d04 ("drm/msm: add sudo flag to submit ioctl")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/547712/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno
510") added special handling for a510 (this SKU doesn't seem to support
preemption, so the driver should clamp nr_rings to 1). However the
gpu->revn is not yet set (it is set later, in adreno_gpu_init()) and
thus the condition is always false. Check config->rev instead.
Fixes: 010c8bbad2 ("drm: msm: adreno: Disable preemption on Adreno 510")
Reported-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Adam Skladowski <a39.skl@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/531511/
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit e25e92e08e ("drm/msm: devcoredump iommu fault support")
enabled SMMU stalling to collect GPU state, but only for a6xx. It tied
enabling the stall with tha per-instance pagetables creation.
Since that commit SoCs with a5xx also gained support for
adreno-smmu-priv. Move stalling into generic code and add corresponding
resume_translation calls.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522720/
Link: https://lore.kernel.org/r/20230214123504.3729522-2-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Downstream driver appears to not support preemption on A510 target,
trying to use one make device slow and fill log with rings related errors.
Set num_rings to 1 to disable preemption.
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: e20c9284c8 ("drm/msm/adreno: Add support for Adreno 510 GPU")
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/526898/
Link: https://lore.kernel.org/r/20230314221757.13096-1-a39.skl@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm-fixes for v6.3-rc2
- Fix for possible invalid ptr free in submit ioctl syncobj cleanup path.
- Synchronize GMU removal in driver teardown path
- a5xx preemption fixes
- Fix runpm imbalance at unbind
- DPU hw catalog fixes:
- set DPU_MDP_PERIPH_0_REMOVED for sc8280xp as this is another chipset
where the PERIPH_0 block of registers is not there
- fix the DPU features supported in QCM2290 by comparing it with the
downstream device tree
- fix the length of registers in the sc7180_ctl from 0xe4 to 0x1dc
- fix the max mixer line width for sm6115 and qcm2290 chipsets in the
DPU catalog
- fix the scaler version on sm8550, sc8280xp, sm8450, sm8250, sm8350
and sm6115. This was incorrectly populated on the SW version of the
scaler library and not the scaler HW version
- Drop dim layer support for msm8998 as its not indicated to be
supported in the downstream DTSI
- fix the DPU_CLK_CTRL bits for msm 8998 sspp blocks
- Use DPU_CLK_CTRL_DMA* prefix instead of DPU_CLK_CTRL_CURSOR*
for all chipsets for the DMA sspp blocks
- fix the ping-pong block base address for sc7280 in the DPU HW catalog
- Fix stack corruption issue in the dpu_hw_ctl_setup_blendstage() function
as it was causing a negative left shift by protecting against an invalid
index
- Clear the DSPP reservations in dpu_rm_release(). This was missed out and
as as result the DSPP was not released from the resource manager global
state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvH+VH_Wx3mFMG51CMnoiU06CM-+-WMhM73M42Qx7Bp4A@mail.gmail.com
Rather than writing CP_PREEMPT_ENABLE_GLOBAL twice, follow the vendor
kernel and set CP_PREEMPT_ENABLE_LOCAL register instead. a5xx_submit()
will override it during submission, but let's get the sequence correct.
Fixes: b1fc2839d2 ("drm/msm: Implement preemption for A5XX targets")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/522638/
Link: https://lore.kernel.org/r/20230214020956.164473-2-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move include/linux/qcom_scm.h to include/linux/firmware/qcom/qcom_scm.h.
This removes 1 of a few remaining Qualcomm-specific headers into a more
approciate subdirectory under include/.
Suggested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Reviewed-by: Guru Das Srinagesh <quic_gurus@quicinc.com>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230203210956.3580811-1-quic_eberman@quicinc.com
The function a6xx_create_address_space() is mostly a copy of
adreno_iommu_create_address_space() with added quirk setting. Rework
these two functions to be a thin wrappers around a common helper.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/509614/
Link: https://lore.kernel.org/r/20221102175449.452283-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
From testing on sc7180-trogdor devices, reading the GMU registers
needs the GMU clocks to be enabled. Those clocks get turned on in
a6xx_gmu_resume(). Confusingly enough, that function is called as a
result of the runtime_pm of the GPU "struct device", not the GMU
"struct device". Unfortunately the current a6xx_gpu_busy() grabs a
reference to the GMU's "struct device".
The fact that we were grabbing the wrong reference was easily seen to
cause crashes that happen if we change the GPU's pm_runtime usage to
not use autosuspend. It's also believed to cause some long tail GPU
crashes even with autosuspend.
We could look at changing it so that we do pm_runtime_get_if_in_use()
on the GPU's "struct device", but then we run into a different
problem. pm_runtime_get_if_in_use() will return 0 for the GPU's
"struct device" the whole time when we're in the "autosuspend
delay". That is, when we drop the last reference to the GPU but we're
waiting a period before actually suspending then we'll think the GPU
is off. One reason that's bad is that if the GPU didn't actually turn
off then the cycle counter doesn't lose state and that throws off all
of our calculations.
Let's change the code to keep track of the suspend state of
devfreq. msm_devfreq_suspend() is always called before we actually
suspend the GPU and msm_devfreq_resume() after we resume it. This
means we can use the suspended state to know if we're powered or not.
NOTE: one might wonder when exactly our status function is called when
devfreq is supposed to be disabled. The stack crawl I captured was:
msm_devfreq_get_dev_status
devfreq_simple_ondemand_func
devfreq_update_target
qos_notifier_call
qos_max_notifier_call
blocking_notifier_call_chain
pm_qos_update_target
freq_qos_apply
apply_constraint
__dev_pm_qos_update_request
dev_pm_qos_update_request
msm_devfreq_idle_work
Fixes: eadf79286a ("drm/msm: Check for powered down HW in the devfreq callbacks")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/489124/
Link: https://lore.kernel.org/r/20220610124639.v4.1.Ie846c5352bc307ee4248d7cab998ab3016b85d06@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move tracking and busy time calculation to msm_devfreq_get_dev_status.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Cc: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220416003314.59211-2-olvaffe@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
The ring seqno counter duplicates the fence-context last_fence counter.
They end up getting incremented in lock-step, on the same scheduler
thread, but the split just makes things less obvious.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220411215849.297838-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
It was always expected to have a use for this some day, so we left a
placeholder. Now we do. (And I expect another use in the not too
distant future when we start allowing userspace to allocate GPU iova.)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20220304005317.776110-3-robdclark@gmail.com
A CP_PROTECT entry for SMMU registers is missing for A540. According to
downstream sources its length is same as on A530 - 0x20000 bytes.
On all other revisions SMMU region length is 0x10000 bytes. Despite
this, we setup region of length 0x20000 on all revisions. This doesn't
cause any issues on those GPUs. As for preventing accesses to the region
from protected mode it was tested to work the same.
This patch drops the "if" condition in setup of CP_PROTECT entry because
it already includes all supported revisions except A540.
Signed-off-by: Vladimir Lypak <vladimir.lypak@gmail.com>
Link: https://lore.kernel.org/r/20211212160333.980343-2-vladimir.lypak@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Add a debugfs interface to ignore hw error irqs, in order to force
fallback to sw hangcheck mechanism. Because the hw error detection is
pretty good on newer gens, we need this for igt tests to test the sw
hang detection.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20211109181117.591148-6-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
cur_ctx_seqno already does the same thing, but handles the edge cases
where a refcnt'd context can live after lastclose. So let's not have
two ways to do the same thing.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>
Link: https://lore.kernel.org/r/20211109181117.591148-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
On a5xx and a6xx devices that are using CP_WHERE_AM_I to update a
ringbuffer read-ptr shadow value, periodically emit a CP_WHERE_AM_I
every 32 commands, so that a later submit waiting for ringbuffer
space to become available sees partial progress, rather than not
seeing rptr advance at all until the GPU gets to the end of the
submit that it is currently chewing on.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Link: https://lore.kernel.org/r/20210428193654.1498482-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
No idea why we were still using this. It certainly hasn't been needed
for some time. So drop the pointless twin codepaths.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Wire up support to stall the SMMU on iova fault, and collect a devcore-
dump snapshot for easier debugging of faults.
Currently this is a6xx-only, but mostly only because so far it is the
only one using adreno-smmu-priv.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Link: https://lore.kernel.org/r/20210610214431.539029-6-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use the new adreno-smmu-priv fault info function to get more SMMU
debug registers and print the current TTBR0 to debug per-instance
pagetables and figure out which GPU block generated the request.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210610214431.539029-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use resource-managed OPP API to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210314163408.22292-12-digetx@gmail.com
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_gem_get_vaddr() currently always maps as writecombine, so use the right
flag instead of relying on broken behavior (things don't actually work if
they are mapped as uncached).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Link: https://lore.kernel.org/r/20210423190833.25319-3-jonathan@marek.ca
Signed-off-by: Rob Clark <robdclark@chromium.org>
They were reading a counter that was configured to ALWAYS_COUNT (ie.
cycles that the GPU is doing something) rather than ALWAYS_ON. This
isn't the thing that userspace is looking for.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Jordan Crouse <jordan@cosmicpenguin.net>
Message-Id: <20210325012358.1759770-2-robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Port over the command from downstream to prevent undefined
behaviour.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The upstream API for some reason uses logbase2 instead of
just passing the argument as-is, whereas downstream CAF
kernel does the latter.
Hence, a mistake has been made when porting:
4 is the value that's supposed to be passed, but
log2(4) = 2. Changing the value to 16 (= 2^4) fixes
the issue.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Resetting the VBIF before power collapse is done to avoid getting
bogus FIFO entries during the suspend sequence or subsequent resume,
but this is doable only on Adreno 510 and Adreno 530, as the other
units will tendentially lock up.
Especially on Adreno 508, the GPU will show lockups and very bad
slownesses after processing the first frame.
Avoiding to execute the RBBM SW Reset before suspend will stop the
lockup issue from happening on at least Adreno 508/509/512.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
