non-drm:
rust:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
mtd:
- driver for Intel GPU non-volatile storage
i2c
- designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support
-----BEGIN PGP SIGNATURE-----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=n9MO
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel
Pull drm updates from Dave Airlie:
"Highlights:
- Intel xe enable Panthor Lake, started adding WildCat Lake
- amdgpu has a bunch of reset improvments along with the usual IP
updates
- msm got VM_BIND support which is important for vulkan sparse memory
- more drm_panic users
- gpusvm common code to handle a bunch of core SVM work outside
drivers.
Detail summary:
Changes outside drm subdirectory:
- 'shrink_shmem_memory()' for better shmem/hibernate interaction
- Rust support infrastructure:
- make ETIMEDOUT available
- add size constants up to SZ_2G
- add DMA coherent allocation bindings
- mtd driver for Intel GPU non-volatile storage
- i2c designware quirk for Intel xe
core:
- atomic helpers: tune enable/disable sequences
- add task info to wedge API
- refactor EDID quirks
- connector: move HDR sink to drm_display_info
- fourcc: half-float and 32-bit float formats
- mode_config: pass format info to simplify
dma-buf:
- heaps: Give CMA heap a stable name
ci:
- add device tree validation and kunit
displayport:
- change AUX DPCD access probe address
- add quirk for DPCD probe
- add panel replay definitions
- backlight control helpers
fbdev:
- make CONFIG_FIRMWARE_EDID available on all arches
fence:
- fix UAF issues
format-helper:
- improve tests
gpusvm:
- introduce devmem only flag for allocation
- add timeslicing support to GPU SVM
ttm:
- improve eviction
sched:
- tracing improvements
- kunit improvements
- memory leak fixes
- reset handling improvements
color mgmt:
- add hardware gamma LUT handling helpers
bridge:
- add destroy hook
- switch to reference counted drm_bridge allocations
- tc358767: convert to devm_drm_bridge_alloc
- improve CEC handling
panel:
- switch to reference counter drm_panel allocations
- fwnode panel lookup
- Huiling hl055fhv028c support
- Raspberry Pi 7" 720x1280 support
- edp: KDC KD116N3730A05, N160JCE-ELL CMN, N116BCJ-EAK
- simple: AUO P238HAN01
- st7701: Winstar wf40eswaa6mnn0
- visionox: rm69299-shift
- Renesas R61307, Renesas R69328 support
- DJN HX83112B
hdmi:
- add CEC handling
- YUV420 output support
xe:
- WildCat Lake support
- Enable PanthorLake by default
- mark BMG as SRIOV capable
- update firmware recommendations
- Expose media OA units
- aux-bux support for non-volatile memory
- MTD intel-dg driver for non-volatile memory
- Expose fan control and voltage regulator in sysfs
- restructure migration for multi-device
- Restore GuC submit UAF fix
- make GEM shrinker drm managed
- SRIOV VF Post-migration recovery of GGTT nodes
- W/A additions/reworks
- Prefetch support for svm ranges
- Don't allocate managed BO for each policy change
- HWMON fixes for BMG
- Create LRC BO without VM
- PCI ID updates
- make SLPC debugfs files optional
- rework eviction rejection of bound external BOs
- consolidate PAT programming logic for pre/post Xe2
- init changes for flicker-free boot
- Enable GuC Dynamic Inhibit Context switch
i915:
- drm_panic support for i915/xe
- initial flip queue off by default for LNL/PNL
- Wildcat Lake Display support
- Support for DSC fractional link bpp
- Support for simultaneous Panel Replay and Adaptive sync
- Support for PTL+ double buffer LUT
- initial PIPEDMC event handling
- drm_panel_follower support
- DPLL interface renames
- allocate struct intel_display dynamically
- flip queue preperation
- abstract DRAM detection better
- avoid GuC scheduling stalls
- remove DG1 force probe requirement
- fix MEI interrupt handler on RT kernels
- use backlight control helpers for eDP
- more shared display code refactoring
amdgpu:
- add userq slot to INFO ioctl
- SR-IOV hibernation support
- Suspend improvements
- Backlight improvements
- Use scaling for non-native eDP modes
- cleaner shader updates for GC 9.x
- Remove fence slab
- SDMA fw checks for userq support
- RAS updates
- DMCUB updates
- DP tunneling fixes
- Display idle D3 support
- Per queue reset improvements
- initial smartmux support
amdkfd:
- enable KFD on loongarch
- mtype fix for ext coherent system memory
radeon:
- CS validation additional GL extensions
- drop console lock during suspend/resume
- bump driver version
msm:
- VM BIND support
- CI: infrastructure updates
- UBWC single source of truth
- decouple GPU and KMS support
- DP: rework I/O accessors
- DPU: SM8750 support
- DSI: SM8750 support
- GPU: X1-45 support and speedbin support for X1-85
- MDSS: SM8750 support
nova:
- register! macro improvements
- DMA object abstraction
- VBIOS parser + fwsec lookup
- sysmem flush page support
- falcon: generic falcon boot code and HAL
- FWSEC-FRTS: fb setup and load/execute
ivpu:
- Add Wildcat Lake support
- Add turbo flag
ast:
- improve hardware generations implementation
imx:
- IMX8qxq Display Controller support
lima:
- Rockchip RK3528 GPU support
nouveau:
- fence handling cleanup
panfrost:
- MT8370 support
- bo labeling
- 64-bit register access
qaic:
- add RAS support
rockchip:
- convert inno_hdmi to a bridge
rz-du:
- add RZ/V2H(P) support
- MIPI-DSI DCS support
sitronix:
- ST7567 support
sun4i:
- add H616 support
tidss:
- add TI AM62L support
- AM65x OLDI bridge support
bochs:
- drm panic support
vkms:
- YUV and R* format support
- use faux device
vmwgfx:
- fence improvements
hyperv:
- move out of simple
- add drm_panic support"
* tag 'drm-next-2025-07-30' of https://gitlab.freedesktop.org/drm/kernel: (1479 commits)
drm/tidss: oldi: convert to devm_drm_bridge_alloc() API
drm/tidss: encoder: convert to devm_drm_bridge_alloc()
drm/amdgpu: move reset support type checks into the caller
drm/amdgpu/sdma7: re-emit unprocessed state on ring reset
drm/amdgpu/sdma6: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5.2: re-emit unprocessed state on ring reset
drm/amdgpu/sdma5: re-emit unprocessed state on ring reset
drm/amdgpu/gfx12: re-emit unprocessed state on ring reset
drm/amdgpu/gfx11: re-emit unprocessed state on ring reset
drm/amdgpu/gfx10: re-emit unprocessed state on ring reset
drm/amdgpu/gfx9.4.3: re-emit unprocessed state on kcq reset
drm/amdgpu/gfx9: re-emit unprocessed state on kcq reset
drm/amdgpu: Add WARN_ON to the resource clear function
drm/amd/pm: Use cached metrics data on SMUv13.0.6
drm/amd/pm: Use cached data for min/max clocks
gpu: nova-core: fix bounds check in PmuLookupTableEntry::new
drm/amdgpu: Replace HQD terminology with slots naming
drm/amdgpu: Add user queue instance count in HW IP info
drm/amd/amdgpu: Add helper functions for isp buffers
drm/amd/amdgpu: Initialize swnode for ISP MFD device
...
Reorder output format arrays in both MT8195 DPI and DP_INTF block
configuration by decreasing preference order instead of alphanumeric
one, as expected by the atomic_get_output_bus_fmts callback function
of drm_bridge controls, so the RGB ones are used first during the
bus format negotiation process.
Fixes: 20fa6a8fc5 ("drm/mediatek: mtk_dpi: Allow additional output formats on MT8195/88")
Signed-off-by: Louis-Alexis Eyraud <louisalexis.eyraud@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20250606-mtk_dpi-mt8195-fix-wrong-color-v1-1-47988101b798@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
devm_drm_bridge_alloc() is the new API to be used for allocating (and
partially initializing) a private driver struct embedding a struct
drm_bridge.
For many drivers having a simple code flow in the probe function, this
commit does a mass conversion automatically with the following semantic
patch. The changes have been reviewed manually for correctness as well as
to find any false positives.
The patch has been applied with the explicit exclusion of bridge/panel.c,
handled by a separate patch.
After applying the semantic patch, manually fixed these issues:
- 4 drivers need ERR_CAST() instead of PTR_ERR() as the function calling
devm_drm_bridge_alloc() returns a pointer
- re-added empty lines and comments that the script had removed but that
should stay
@@
type T;
identifier C;
identifier BR;
expression DEV;
expression FUNCS;
@@
-T *C;
+T *C;
...
(
-C = devm_kzalloc(DEV, ...);
-if (!C)
- return -ENOMEM;
+C = devm_drm_bridge_alloc(DEV, T, BR, FUNCS);
+if (IS_ERR(C))
+ return PTR_ERR(C);
|
-C = devm_kzalloc(DEV, ...);
-if (!C)
- return ERR_PTR(-ENOMEM);
+C = devm_drm_bridge_alloc(DEV, T, BR, FUNCS);
+if (IS_ERR(C))
+ return PTR_ERR(C);
)
...
-C->BR.funcs = FUNCS;
Reviewed-by: Manikandan Muralidharan <manikandan.m@microchip.com> # microchip-lvds.c
Reviewed-by: Douglas Anderson <dianders@chromium.org> # parade-ps8640
Tested-by: Douglas Anderson <dianders@chromium.org> # parade-ps8640
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20250509-drm-bridge-convert-to-alloc-api-v3-2-b8bc1f16d7aa@bootlin.com
[Luca: fixed trivial patch conflict in adv7511_drv.c while applying]
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
1. Prepare for support MT8195/88 HDMIv2 and DDCv2
2. DPI: Cleanups and add support for more formats
3. Cleanups and sanitization
4. Replace custom compare_dev with component_compare_of
-----BEGIN PGP SIGNATURE-----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=bcEP
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-20250515' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next - 20250515
1. Prepare for support MT8195/88 HDMIv2 and DDCv2
2. DPI: Cleanups and add support for more formats
3. Cleanups and sanitization
4. Replace custom compare_dev with component_compare_of
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20250514233647.15907-1-chunkuang.hu@kernel.org
For the sake of increasing human readability and avoid possible
confusion between DPI and DP_INTF output formats (as the two are
ever so slightly different), rename the mt8195_output_fmts array
to mt8195_dp_intf_output_fmts.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250409131306.108635-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Allow additional output formats in both DPI and DP_INTF blocks of
the MT8195 and MT8188 SoCs (as the latter is fully compatible with,
hence reuses, the former's platform data for both blocks) by adding:
1. New formats to the `mt8195_output_fmts` array for dp_intf,
lacking YUV422 12-bits support, and adding RGB888 2X12_LE/BE
(8-bits), BGR888 (8-bits) RGB101010 1x30 (10-bits), and YUV
formats, including YUV422 8/10 bits, and YUV444 8/10 bits; and
2. A new `mt8195_dpi_output_fmts` array for DPI only, with all of
for formats added to dp_intf and with the addition of the
YUYV12_1X24 (YUV422 12-bits) output format.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250409131306.108635-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add support for configuring the Display Parallel Interface block
to output YUV444 8/10 bits, YUV422 10/12 bits (8 bits support is
already present), BGR 8-bits, and RGB 10-bits.
The enablement of the various additional output formats in SoCs
platform data will be done in a different change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250409131306.108635-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for additional color formats,
add local helpers to map media bus format parameters to this
driver's bit_num, channel_swap and color_format.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250409131306.108635-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for an additional color format,
convert the format conditional in mtk_dpi_config_color_format()
to a switch.
This also makes the concept of RGB being the default color format
a little more human readable.
This commit brings no functional differences.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250409131306.108635-2-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
In preparation for adding support for MT8195's HDMI reserved
DPI, add calls to clk_prepare_enable() / clk_disable_unprepare()
for the TVD clock: in this particular case, the aforementioned
clock is not (and cannot be) parented to neither pixel or engine
clocks hence it won't get enabled automatically by the clock
framework.
Please note that on all of the currently supported MediaTek
platforms, the TVD clock is always a parent of either pixel or
engine clocks, and this means that the common clock framework
is already enabling this clock before the children.
On such platforms, this commit will only increase the refcount
of the TVD clock without any functional change.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
On some SoCs, like MT8195 and MT8188, the DPI's FIFO controller
(afifo) supports outputting either one or two pixels per round
regardless of the input being 1T1P or 1T2P.
Add a `output_1pixel` member to struct mtk_dpi_conf which, if
set, will enable outputting one pixel per clock.
In case the input is two pixel per clock (1T2P), the AFIFO HW
will automatically (and internally) convert it to 1T1P.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-9-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
On some SoCs, like MT8195 and MT8188, the DPI instance that is
reserved to the HDMI Transmitter uses a different clock topology.
In this case, the DPI is clocked by the HDMI IP, and this outputs
its clock to the MM input of dpi_pixel_clk, which is essential to
enable register access to the DPI IP.
Add a `clocked_by_hdmi` member to struct mtk_dpi_conf, and check
it to avoid enabling the DPI clocks in the mediatek-drm internal
.start() callback (and avoid disabing in the .stop() component
callback): this will make sure that the clock configuration
sequence is respected during display pipeline setup by following
the bridge ops between DPI and HDMI, where the HDMI driver is
expected to enable the clocks in the bridge's pre_enable(), and
DPI in the enable() cb.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for MT8195's HDMI reserved DPI
instance, move the input_2p_en bit for DP_INTF to platform data.
While at it, remove the input_2pixel member from platform data as
having this bit implies that the 2pixel feature must be enabled.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for newer DPI instances which
do support direct-pin but do not have any H_FRE_CON register,
like the one found in MT8195 and MT8188, add a branch to check
if the reg_h_fre_con variable was declared in the mtk_dpi_conf
structure for the probed SoC DPI version.
As a note, this is useful specifically only for cases in which
the support_direct_pin variable is true, so mt8195-dpintf is
not affected by any issue.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
In preparation for adding support for the DPI IP found in MT8195
and in MT8188 used for HDMI, move the code flow for calculation
and setting of the DPI pixel clock to a separate function called
mtk_dpi_set_pixel_clk().
This was done because, on those platforms, the DPI instance that
is used for HDMI will get its pixel clock from the HDMI clock,
hence it is not necessary, nor desirable, to calculate or set
the pixel clock in DPI.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Setting the TVD PLL clock requires to multiply the target pixel
clock by a specific constant factor to achieve the target PLL
frequency, and this is done to reduce jitter to acceptable levels.
On all MediaTek SoCs, the factor is not retrieved by any real kind
of calculation but rather by checking if the target pixel clock
is less than a specified frequency, hence assigning a function
pointer for just a bunch of if branches does enlarge the code
size for little reason.
Remove all SoC-specific functions, add a structure `mtk_dpi_factor`
that holds a clock frequency and corresponding PLL factor, and
declare the constraints for each SoC in form of an array of said
structure.
Instead of function pointers, this structure (and its size) is then
assigned to each SoC's platform data.
The "calculation" is then performed with a new static function
mtk_dpi_calculate_factor(dpi, mode_clk) that iterates through all
of the entries of the aforementioned array and returns the right
factor.
If no factor is found, the lowest possible factor is returned,
mimicking the same flow as all of the old per-SoC calculation
functions.
This commit brings no functional change.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This IP includes a Pattern Generator which is useful for debugging
and testing purposes: add the relevant register and bits to the
mtk_dpi_regs.h header, and implement support for it in mtk_dpi.
Adding this required to introduce a .debugfs_init() callback for
the DPI bridge, which creates a "dpi_test_pattern" file in the
directory of the appropriate connector.
The pattern generator can generate various internal patterns and
this submission includes support for:
- 256 or 1024 shades of gray in a Vertical or Horizontal Pattern
- Vertical Color Bars
- Frame border
- Dot Moire
This generator also supports filling the entire screen with one
custom color, but support for that is not included in this commit.
Enabling and disabling this generator can be done by sending a
string to the dpi_test_pattern debugfs file; the pattern is
expected to be formatted as follows:
<enable (1) or disable (0)> <pattern number>
where the pattern number can be a number from 0 to 7, excluding 5.
Of course 5 is excluded because that activates custom color fill
which, again, is not supported in this commit.
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20250217154836.108895-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is impossible to add each and every possible DDP path combination
for each and every possible combination of SoC and board: right now,
this driver hardcodes configuration for 10 SoCs and this is going to
grow larger and larger, and with new hacks like the introduction of
mtk_drm_route which is anyway not enough for all final routes as the
DSI cannot be connected to MERGE if it's not a dual-DSI, or enabling
DSC preventively doesn't work if the display doesn't support it, or
others.
Since practically all display IPs in MediaTek SoCs support being
interconnected with different instances of other, or the same, IPs
or with different IPs and in different combinations, the final DDP
pipeline is effectively a board specific configuration.
Implement OF graphs support to the mediatek-drm drivers, allowing to
stop hardcoding the paths, and preventing this driver to get a huge
amount of arrays for each board and SoC combination, also paving the
way to share the same mtk_mmsys_driver_data between multiple SoCs,
making it more straightforward to add support for new chips.
Note that the OVL_ADAPTOR software component driver needs relatively
big changes in order to fully support OF Graphs (and more SoCs anyway)
and such changes will come at a later time.
As of now, the mtk_disp_ovl_adaptor driver takes the MERGE components
(for example, on mt8195, merge 1 to 4) dynamically so, even though
later updates to the ovl-adaptor driver will *not* require bindings
changes, the merge1-4 will be temporarily omitted in the graph for the
MT8195 SoC.
This means that an example graph for this SoC looks like:
mdp_rdma (0 ~ 7) -> padding (0 ~ 7) -> ethdr -> merge5
and the resulting path in this driver will be `ovl_adaptor -> merge5`
Later updates to the ovl adaptor will expand it to support more SoCs
and, in turn, to also fully support graphs.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Tested-by: Michael Walle <mwalle@kernel.org> # on kontron-sbc-i1200
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241017103809.156056-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk_find_possible_crtcs() assumes that the main path will always have
the CRTC with id 0, the ext id 1 and the third id 2. This is only true
if the paths are all available. But paths are optional (see also
comment in mtk_drm_kms_init()), e.g. the main path might not be enabled
or available at all. Then the CRTC IDs will shift one up, e.g. ext will
be 0 and the third path will be 1.
To fix that, dynamically calculate the IDs by the presence of the paths.
While at it, make the return code a signed one and return -ENODEV if no
path is found and handle the error in the callers.
Fixes: 5aa8e76476 ("drm/mediatek: dpi/dsi: Change the getting possible_crtc way")
Suggested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240606092122.2026313-1-mwalle@kernel.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Rename functions of mtk_ddp_comp:
- To align the naming rule
- To reduce the code size
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.corp-partner.google.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240322091232.26387-15-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Rename files mtk_drm_ddp_comp.h to mtk_ddp_comp.h.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.corp-partner.google.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240322091232.26387-9-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DPI input is in 1T2P mode on both MT8195 and MT8188.
Remove the redundant driver data to align the settings, or
the screen will glitch.
Fixes: 2847cd7e64 ("drm/mediatek: Add mt8188 dpi compatibles and platform data")
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hsiao Chien Sung <shawn.sung@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231214055847.4936-22-shawn.sung@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Add implementation of mtk_dpi_encoder_index to mtk_ddp_comp_func
to make mtk_dpi support dynamic connector selection.
Signed-off-by: Jason-JH.Lin <jason-jh.lin@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20231004024013.18956-7-jason-jh.lin@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reduce line count by compressing the entries of struct of_device_id;
while at it, also add the usual /* sentinel */ comment to the last
entry.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-7-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Instead of the open-coded platform_get_resource, devm_ioremap_resource
switch to devm_platform_ioremap_resource(), also dropping the useless
struct resource pointer, which becomes unused.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-6-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Function drm_of_find_panel_or_bridge() is marked as deprecated: since
the usage of that in this driver exactly corresponds to the new function
devm_drm_of_get_bridge(), switch to it.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Fei Shao <fshao@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230726082245.550929-4-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
Dpi output needs to adjust the output format to dual edge for MT8186.
Co-developed-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1666577099-3859-3-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Modify dpi power on/off sequence so that the first gpio operation will
take effect.
Fixes: 6bd4763fd5 ("drm/mediatek: set dpi pin mode to gpio low to avoid leakage current")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
1. Add Mediatek Soc DRM (vdosys0) support for mt8195
2. Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence
3. Add mt8186 dsi compatible and convert dsi_dtbinding to .yaml
4. Add MediaTek SoC DRM (vdosys1) support for mt8195
5. Add MT8195 dp_intf driver
-----BEGIN PGP SIGNATURE-----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=0Z1o
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-next-5.20' of https://git.kernel.org/pub/scm/linux/kernel/git/chunkuang.hu/linux into drm-next
Mediatek DRM Next for Linux 5.20
1. Add Mediatek Soc DRM (vdosys0) support for mt8195
2. Cooperate with DSI RX devices to modify dsi funcs and delay mipi high to cooperate with panel sequence
3. Add mt8186 dsi compatible and convert dsi_dtbinding to .yaml
4. Add MediaTek SoC DRM (vdosys1) support for mt8195
5. Add MT8195 dp_intf driver
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fix drm_edid.h include]
From: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220709142021.24260-1-chunkuang.hu@kernel.org
Dpintf is the displayport interface hardware unit. This unit is similar
to dpi and can reuse most of the code.
This patch adds support for mt8195-dpintf to this dpi driver. Main
differences are:
- 4 pixels for one iteration for dp_intf while dpi is 1 pixel for one
iteration.
- Input of dp_intf is two pixels per iteration.
- Some register contents differ slightly between the two components.
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-6-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The quantity of output for one iteration could be different for dpi and
dp_intf. For dp_intf, it's 4 pixels for one iteration it's 1 pixel for one
iteration for dpi. Therefore, we add a new config "pixels_per_iter" to
control quantity of transferred pixels per iteration.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-5-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
MediaTek dpi supports direct connection to dpi panels while dp_intf does
not support. Therefore, add a config "support_direct_pin" to control this.
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-3-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Dp_intf supports YUV422 as output format. In MT8195 Chrome project,
YUV422 output format is used for 4K resolution.
To support this, it is also needed to support color format transfer.
Color format transfer is a new feature for both dpi and dpintf of MT8195.
The input format could be RGB888 and output format for dp_intf should be
YUV422. Therefore, we add a mtk_dpi_matrix_sel() helper to update the
DPI_MATRIX_SET register depending on the color format.
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220705102530.1344-2-rex-bc.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
drm_crtc.h has no need for linux/media-bus-format.h, so don't
include it. Avoids useless rebuilds of the entire universe when
touching linux/media-bus-format.h.
Quite a few placs do currently depend on linux/media-bus-format.h
without actually including it directly. All of those need to be
fixed up.
v2: Deal with ingenic as well
v3: Fix up mxsfb and remaining parts of imx
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220630195114.17407-4-ville.syrjala@linux.intel.com
