Add support for the TI TPS65214 PMIC with the addition of an id_table,
separate TPS65214 template_chip, and device-specific _change_direction
functions.
- Use platform_get_device_id() to assign dev-specific information.
- Use different change_direction() functions since TPS65214's GPIO
configuration bits are changeable during device operation through bit
GPIO_CONFIG in GENERAL_CONFIG register.
- Remove MODULE_ALIAS since it is now generated by MODULE_DEVICE_TABLE.
Reviewed-by: Jonathan Cormier <jcormier@criticallink.com>
Tested-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250722181609.1541739-3-s-ramamoorthy@ti.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
TPS65215 and TPS65219 are overlapping PMIC devices. While their regulator
features differe, the GPIO features are the same. In the TPS65219 MFD
driver, the 2 PMICs share the same "tps65219-gpio" compatible string to
limit support for TPS65215 in this GPIO driver to comments.
The TPS6521X_GPIO0_IDX and TPS6521X_GPIO0_OFFSET macro name prefixes are
updated to indicate these macros apply to both PMICs.
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20250722181609.1541739-2-s-ramamoorthy@ti.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Replace the user-defined macros with the equivalent kernel macros provided.
The user-defined macros serve the same purpose as the common kernel macros.
The user-defined macros rely on the inference that _IN corresponds to true
and _OUT is false.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20241217204755.1011731-2-s-ramamoorthy@ti.com
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
CONFIG_DEBUG_GPIO should only be used to enable debug log messages and
for core GPIOLIB debugging. Don't use it to control the execution of
potentially buggy code. Just put it under an always-false #if.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add support for TPS65219 PMICs GPIO interface.
3 GPIO pins:
- GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
- GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
GPIO0 is statically configured as input or output prior to Linux boot.
it is used for MULTI_DEVICE_ENABLE function.
This setting is statically configured by NVM.
GPIO0 can't be used as a generic GPIO (specification Table 8-34).
It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
Datasheet describes specific usage for non standard GPIO.
Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
Co-developed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
