The RZ/{G2L,V2L,G3S} CPG versions support a feature called MSTOP. Each
module has one or more MSTOP bits associated with it, and these bits
need to be configured along with the module clocks. Setting the MSTOP
bits switches the module between normal and standby states.
Previously, MSTOP support was abstracted through power domains (struct
generic_pm_domain::{power_on, power_off} APIs). With this abstraction,
the order of setting the MSTOP and CLKON bits was as follows:
Previous Order:
A/ Switching to Normal State (e.g., during probe):
1/ Clear module MSTOP bit
2/ Set module CLKON bit
B/ Switching to Standby State (e.g., during remove):
1/ Clear CLKON bit
2/ Set MSTOP bit
However, in some cases (when the clock is disabled through devres), the
order may have been (due to the issue described in link section):
1/ Set MSTOP bit
2/ Clear CLKON bit
Recently, the hardware team has suggested that the correct order to set
the MSTOP and CLKON bits is:
Updated Order:
A/ Switching to Normal State (e.g., during probe):
1/ Set CLKON bit
2/ Clear MSTOP bit
B/ Switching to Standby State (e.g., during remove):
1/ Set MSTOP bit
2/ Clear CLKON bit
To prevent future issues due to incorrect ordering, the MSTOP setup has
now been implemented in rzg2l_mod_clock_endisable(), ensuring compliance
with the sequence suggested in Figure 41.5: Module Standby Mode
Procedure from the RZ/G3S HW manual, Rev1.10.
Additionally, since multiple clocks of a single module may be mapped to
a single MSTOP bit, MSTOP setup is reference-counted.
Furthermore, as all modules start in the normal state after reset, if
the module clocks are disabled, the module state is switched to standby.
This prevents keeping the module in an invalid state, as recommended by
the hardware team.
Link: https://lore.kernel.org/all/20250215130849.227812-1-claudiu.beznea.uj@bp.renesas.com/
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250527112403.1254122-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock and reset entries for the DRP-AI block, which is available only
on the Renesas RZ/V2L SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250106202853.262787-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The r9a07g044_resets array describes the reset signals in this SoC and
does not change at runtime.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240320082831.9666-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Refactor SD MUX driver to be able to reuse the same code on RZ/G3S.
RZ/G2{L,UL} has a limitation with regards to switching the clock source
for SD MUX (MUX clock source has to be switched to 266MHz before
switching b/w 533MHz and 400MHz). Rework the handling of this limitation
to use a clock notifier that is registered according to platform based
initialization data, so the SD MUX code can be reused on RZ/G3S.
As RZ/G2{L,UL} and RZ/G3S use different bits in different registers to
check if the clock switching has been done, this configuration (register
offset, register bits and bitfield width) is now passed through struct
cpg_core_clk::sconf (status configuration) from platform specific
initialization code.
Along with struct cpg_core_clk::sconf the mux table indices are also
passed from platform specific initialization code.
Also, mux flags are now passed to DEF_SD_MUX() as they will be used
later by RZ/G3S.
CPG_WEN_BIT macro has been introduced to select properly the WEN bit
of various registers.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231006103959.197485-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Remove CPG_SDHI_DSEL and its bits from the generic header as RZ/G3S has
different offset registers and bits for this, thus avoid mixing them.
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230929053915.1530607-10-claudiu.beznea@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CRU clock and reset entries to CPG driver.
CRU_SYSCLK and CRU_VCLK clocks need to be turned ON/OFF in particular
sequence for the CRU block hence add these clocks to
r9a07g044_no_pm_mod_clks[] array and pass it as part of CPG data for
both RZ/G2L and RZ/V2L SoCs.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221221212703.348278-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
WDT CH2 is specifically to check the operation of Cortex-M33 CPU and if
used from CA55 CPU would result in an unexpected behaviour. Hence drop
WDT2 clock and reset entries.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20221009231013.14791-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add conditional compilation for struct r9a07g044_cpg_info, so the
compiler won't allocate any memory for this variable in case
CONFIG_CLK_R9A07G044 is disabled.
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220804082605.157269-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/V2M SoC doesn't use CLK_MON registers, so make them optional.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-9-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All of the muxes and dividers that can be modified require the HIWORD
flags, so make the macros set them. It won't affect read only muxes and
dividers.
This will make the clock tables a little easier to read, particularly for
new SoCs coming.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-8-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We only ever use ARRAY_SIZE() to populate the number of parents, so
move this into the macro to always detect it automatically. This
also makes the tables of clocks a little simpler.
Similarly for the DEF_SD_MUX macro.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220503115557.53370-6-phil.edworthy@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock structure for RZ/V2L is almost identical to the RZ/G2L SoC.
The only difference being that RZ/V2L has additional registers to
control clocks and resets for the DRP-AI block.
Reuse r9a07g044-cpg.c, as the clock IDs and reset IDs are the same
between RZ/G2L and RZ/V2L, and add a separate r9a07g054_cpg_info to take
care of the DRP-AI clocks/resets.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220205084006.7142-1-biju.das.jz@bp.renesas.com
Link: https://lore.kernel.org/r/20220209203411.22332-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As per the HW manual (Rev.1.00 Sep, 2021) PLL2 and PLL3 should be
1600 MHz, but with current multiplier and divider values this resulted
to 1596 MHz.
This patch updates the multiplier and divider values for PLL2 and PLL3
so that we get the exact (1600 MHz) values.
Fixes: 17f0ff3d49 ("clk: renesas: Add support for R9A07G044 SoC")
Suggested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211223093223.4725-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
G clock is sourced from PLL3 and PLL6. The output of the mux is
connected to divider.
This patch adds a mux and divider for getting different rates from
this clock sources.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macro CLK_PLL3_DIV4->CLK_PLL3_DIV2_2 to match the clock tree
mentioned in the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211203115154.31864-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core clock "I" is sourced from CPG_PL1_DDIV divider as per HW manual
Rev.1.00.
This patch adds clock divider table "dtable_1_8" and switches to
DEF_DIV for "I" clock.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211112081003.15453-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Rename the macros CLK_PLL2_DIV16->CLK_PLL2_DIV2_8 and
CLK_PLL2_DIV20->CLK_PLL2_DIV2_10 to match the clock tree mentioned in
the hardware manual(Rev.1.00 Sep, 2021).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110082019.28554-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Ethernet reference clock can be sourced from PLL5_FOUT3 or PLL6. Add
support for ethernet source clock selection using SEL_PLL_6_2 mux.
This patch also renames the PLL5_DIV2 core clock to PLL5_250 to match
with the register description as mentioned in RZ/G2L HW manual (Rev.1.00).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922155145.28156-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IA55_CLK and DMAC_ACLK as critical clocks.
Previously it worked ok, because of a bug in clock status function
and the following patch in this series fixes the original bug.
Fixes: c3e67ad6f5 ("dt-bindings: clock: r9a07g044-cpg: Update clock/reset definitions")
Fixes: eb829e549b ("clk: renesas: r9a07g044: Add DMAC clocks/resets")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922112405.26413-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
