Include mod_devicetable.h for the 'struct of_device_id' and
clk-provider.h for the 'struct clk_hw'.
Reviewed-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250212-b4-clk-qcom-clean-v3-3-499f37444f5d@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The previous wrapper qcom_cc_really_probe takes the platform
device as parameter, which is limited to platform driver.
As for qca8k clock controller driver, which is registered as
the MDIO device, which also follows the qcom clock framework.
To commonize qcom_cc_really_probe, updating it to take the
struct device as parameter, so that the qcom_cc_really_probe
can be utilized by the previous platform device and the new
added MDIO device.
Also update the current clock controller drivers to take
&pdev->dev as parameter when calling qcom_cc_really_probe.
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Link: https://lore.kernel.org/r/20240605124541.2711467-4-quic_luoj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add support to update the GDSC transition delay values to avoid
the GDSC FSM state stuck issues without which it could lead to GDSC
power on/off failures.
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240531095142.9688-2-quic_tdas@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Instead of magically poking at the bit0 of branch clocks' CBCR, use
the newly introduced helper.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240212-topic-clk_branch_en-v7-2-5b79eb7278b2@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There is no need to register GPU clock controllers during subsys init
calls. Use module_platform_driver() instead.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240206-clk-module-platform-driver-v1-3-db799bd2feeb@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
There are few GPU clocks which are powering up the memories
and thus enable the FORCE_MEM_PERIPH always for these clocks
to force the periph_on signal to remain active during halt
state of the clock.
Fixes: a3cc092196 ("clk: qcom: Add Global Clock controller (GCC) driver for SC7280")
Fixes: 3e0f01d6c7 ("clk: qcom: Add graphics clock controller driver for SC7280")
Signed-off-by: Taniya Das <quic_tdas@quicinc.com>
Signed-off-by: Satya Priya <quic_c_skakit@quicinc.com>
Link: https://lore.kernel.org/r/1666159535-6447-1-git-send-email-quic_c_skakit@quicinc.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the graphics clock controller found on SC7280
based devices. This would allow graphics drivers to probe and
control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/1626189143-12957-6-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
