The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device can be unbound or probe can fail, so driver must also release
memory for the wakeup source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
To prevent Bluetooth SDIO card from be physically removed suddenly,
driver needs to ensure btmtksdio_close is called before
btmtksdio_remove to disable interrupts and txrx workqueue.
Fixes: 6ac4233afb ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Check BTMTKSDIO_FUNC_ENABLED flag before doing close to prevent
btmtksdio_close been called twice.
Fixes: 6ac4233afb ("Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal")
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ensure interrupts are not re-enabled when the IRQ handler has already been
removed. This prevents unexpected IRQ handler execution due to stale or
unhandled interrupts.
Modify btmtksdio_txrx_work to check if bdev->func->irq_handler exists
before calling sdio_writel to enable interrupts.
Co-developed-by: Pedro Tsai <pedro.tsai@mediatek.com>
Signed-off-by: Pedro Tsai <pedro.tsai@mediatek.com>
Co-developed-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Felix Freimann <felix.freimann@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The hdev->reset is never used now and the hdev->cmd_timeout actually
does reset. This patch changes the call path from
hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset
, to
hdev->reset -> vendor_reset -> btusb_reset
Which makes it clear when we export the hdev->reset to a wider usage
e.g. allowing reset from sysfs.
This patch doesn't introduce any behavior change.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the device tree is properly written, the SDIO function device node
should be correctly defined, and the mmc core in Linux should correctly
tie it to the device being probed.
Only fall back to searching for the device node by compatible if the
original device node tied to the device is incorrect, as seen in older
device trees.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> #
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
asm/unaligned.h is always an include of asm-generic/unaligned.h;
might as well move that thing to linux/unaligned.h and include
that - there's nothing arch-specific in that header.
auto-generated by the following:
for i in `git grep -l -w asm/unaligned.h`; do
sed -i -e "s/asm\/unaligned.h/linux\/unaligned.h/" $i
done
for i in `git grep -l -w asm-generic/unaligned.h`; do
sed -i -e "s/asm-generic\/unaligned.h/linux\/unaligned.h/" $i
done
git mv include/asm-generic/unaligned.h include/linux/unaligned.h
git mv tools/include/asm-generic/unaligned.h tools/include/linux/unaligned.h
sed -i -e "/unaligned.h/d" include/asm-generic/Kbuild
sed -i -e "s/__ASM_GENERIC/__LINUX/" include/linux/unaligned.h tools/include/linux/unaligned.h
This inverts the LE State quirk so by default we assume the controllers
would report valid states rather than invalid which is how quirks
normally behave, also this would result in HCI command failing it the LE
States are really broken thus exposing the controllers that are really
broken in this respect.
Link: https://github.com/bluez/bluez/issues/584
Fixes: 220915857e ("Bluetooth: Adding driver and quirk defs for multi-role LE")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Move btusb_mtk_hci_wmt_sync from btusb.c to btmtk.c which holds
vendor specific stuff and would make btusb.c clean.
Add usb.h header to btmtksdio.c/btmtkuart.c for usb related element
defined in btmtk.h
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Apply the common btmtk_fw_get_filename to avoid the similar coding in each
driver.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The BTMTKSDIO_BT_WAKE_ENABLED flag is set for bluetooth interrupt
during system suspend and increases wakeup count for bluetooth event.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit ce64b3e949 ("Bluetooth: mt7921s: Support wake on bluetooth")
adds the wake on bluethooth via a dedicated GPIO.
Extend the wake-on-bluetooth to use the SDIO DAT1 pin (in-band wakeup),
when supported by the SDIO host driver.
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sending WMT command during the reset in progress is invalid and would get
no response from firmware until the reset is complete, so we ignore the WMT
command here to resolve the issue which causes the whole reset process
taking too long.
Fixes: 8fafe70225 ("Bluetooth: mt7921s: support bluetooth reset mechanism")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to FW advised sequence, mt7921s need to re-acquire privilege
immediately after the firmware download is complete before normal running.
Otherwise, it is still possible the bus may be stuck in an abnormal status
that causes FW initialization failure in the current driver.
Fixes: 752aea5848 ("Bluetooth: mt7921s: fix bus hang with wrong privilege")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the incorrect pointer check on ven_data.
Fixes: f41b91fa17 ("Bluetooth: mt7921s: Add .btmtk_get_codec_config_data")
Co-developed-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
It is time to add wide band speech (WBS) support.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add .btmtk_get_codec_config_data to get codec configuration data.
In HFP offload usecase, controllers need to be set codec details before
opening SCO. This callback function is used to fetch vendor specific codec
config data.
This is a preliminary patch to add the WBS support to the MT7921 driver.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add .get_data_path_id to fetch data_path_id for MT7921 to support HFP
offload use case.
This is a preliminary patch to add the WBS support to the MT7921 driver.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The patch set HCI_QUIRK_VALID_LE_STATES to be consistent with the btusb for
MT7921 and is required for the likes of experimental LE simultaneous roles.
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the following kernel oops in btmtksdio_interrrupt
[ 14.339134] btmtksdio_interrupt+0x28/0x54
[ 14.339139] process_sdio_pending_irqs+0x68/0x1a0
[ 14.339144] sdio_irq_work+0x40/0x70
[ 14.339154] process_one_work+0x184/0x39c
[ 14.339160] worker_thread+0x228/0x3e8
[ 14.339168] kthread+0x148/0x3ac
[ 14.339176] ret_from_fork+0x10/0x30
That happened because hdev->power_on is already called before
sdio_set_drvdata which btmtksdio_interrupt handler relies on is not
properly set up.
The details are shown as the below: hci_register_dev would run
queue_work(hdev->req_workqueue, &hdev->power_on) as WQ_HIGHPRI
workqueue_struct to complete the power-on sequeunce and thus hci_power_on
may run before sdio_set_drvdata is done in btmtksdio_probe.
The hci_dev_do_open in hci_power_on would initialize the device and enable
the interrupt and thus it is possible that btmtksdio_interrupt is being
called right before sdio_set_drvdata is filled out.
When btmtksdio_interrupt is being called and sdio_set_drvdata is not filled
, the kernel oops is going to happen because btmtksdio_interrupt access an
uninitialized pointer.
Fixes: 9aebfd4a22 ("Bluetooth: mediatek: add support for MediaTek MT7663S and MT7668S SDIO devices")
Reviewed-by: Mark Chen <markyawenchen@gmail.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Yake Yang <yake.yang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a conflict between MediaTek wmt event and msft vendor extension
logic in the core layer since 145373cb1b ("Bluetooth: Add framework for
Microsoft vendor extension") was introduced because we changed the type of
mediatek wmt event to the type of msft vendor event in the driver.
But the purpose we reported mediatek event to the core layer is for the
diagnostic purpose with that we are able to see the full packet trace via
monitoring socket with btmon. Thus, it is harmless we keep the original
type of mediatek vendor event here to avoid breaking the msft extension
function especially they can be supported by Mediatek chipset like MT7921
, MT7922 devices and future devices.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Implement .cmd_timeout to reset the MT7921s device via a dedicated GPIO
pin when the firmware hang or the command has no response.
Co-developed-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chih-Ying Chiang <chih-yin.chiang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, there is a loop in btmtksdio_txrx_work() which iteratively
executes until the variable int_status is zero.
But the variable int_status should be masked out with the actual interrupt
sources (MTK_REG_CHISR bit 0-15) before we check the loop condition.
Otherwise, RX_PKT_LEN (MTK_REG_CHISR bit 16-31) which is read-only and
unclearable would cause the loop to get stuck on some chipsets like
MT7663s.
Fixes: 26270bc189 ("Bluetooth: btmtksdio: move interrupt service to work")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Apply sleep mode by default and a smaller idle time to reduce power
consumption further.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Lower its log level from INFO to DEBUG prior to we enable runtime pm for
mt7921s with the smaller idle time as default.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the firmware behavior (even the oldest one in linux-firmware)
If the firmware is downloaded, MT7921S must rely on the additional mailbox
mechanism that resides in firmware to check if the device is the right
state for btmtksdio_mcu_[drv|fw]_pmctrl(). Otherwise, we still apply the
old way for that.
That is a necessary patch before we enable runtime pm for mt7921s as
default.
Fixes: c603bf1f94 ("Bluetooth: btmtksdio: add MT7921s Bluetooth support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to chip hw flow, mt7921s need to re-acquire privilege
again before normal running. Otherwise, the bus may be stuck in
an abnormal status.
Fixes: c603bf1f94 ("Bluetooth: btmtksdio: add MT7921s Bluetooth support")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refactor btmtksdio_runtime_[suspend|resume]() to create the common
funcitons btmtksdio_[fw|drv]_pmctrl() shared with btmtksdio_[open|close]()
to avoid the redundant code as well.
This is also a prerequisite patch for the incoming patches.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
According to the MCU firmware behavior, as the driver is aware of the
notification of the interrupt source FW_MAILBOX_INT that shows the MCU
completed delivered a core dump piece to the host, the driver must
acknowledge the MCU with the register PH2DSM0R bit PH2DSM0R_DRIVER_OWN
to notify the MCU to handle the next core dump piece.
Fixes: db57b62591 ("Bluetooth: btmtksdio: add support of processing firmware coredump and log")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Have "..reg (%d)" to be consistent with the other similar error messages.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
move struct reg_read_cmd to btmtk.h to allow other mtk drivers refer to.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver has to issue the specific command to enable Bluetooth SCO over
the I2S/PCM interface on mt7921s, that is supported since the firmware
with version 20211222191101 was added, and the patch would not cause any
harm even when the old firmware is applied.
The SCO profile with the patch was tested by setting up a VOIP application,
connected to HFP device, checked telephony function can work normally.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enable wake on bluetooth on mt7921s that can be supported since the
firmware with version 20211129211059 was added, and the patch would
not cause any harm even when the old firmware is applied.
The patch was tested by setting up an HID or HOGP profile to connect a
Bluetooth keyboard and mouse, then putting the system to suspend, then
trying to wake up the system by moving the Bluetooth keyboard or mouse,
and then checking if the system can wake up and be brought back to
the normal state.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Using "btmtksdio" as the prefix instead of "btsdio"
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to MT7921 btusb, we enable AOSP extension for MT7921 btmtksdio
as well.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that
SDIO power is being shut off during the device is in suspend. That fixes
the SDIO command fails to access the bus after the device is resumed.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Runtime pm ops is not aware the sdio_func status that is probably
being disabled by btmtksdio_close. Thus, we are only able to access the
sdio_func for the runtime pm operations only when the sdio_func is
available.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the existent variable to drop the unnecessary variable created.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support of processing the firmware coredump and log for the diagnostic
purpose.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
add MT7921s Bluetooth support
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Each packet should be sent out until the device emits the TX_EMPTY signal
to the host, that is firmware people suggested to add to meet the actual
firmware behavior and that is compatible among all the devices.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That is a preliminary patch to introduce mt7921s support.
Use the register CRPLR to read packet length to make all the devices
share the common logic.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
That is a preliminary patch to introduce mt7921s support.
Update register CSDIOCSR operation that is suggested from the vendor
driver and is compatible to the all devices.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmtksdio belongs to WIFI/BT combo chip that would serve two radios in one
sdio_irq so that we have to move interrupt service to worker to ensure ISR
as short as possible.
The worker would serve the both Tx and Rx in a batch to effectively reduce
many interrupts to the host and to avoid excessive sdio lock contention
between various context (even from WiFi driver) and help to be more
efficient to complete command/event transation.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
