The firmware raises an alive interrupt upon sending the HCI_RESET or
BTINTEL_HCI_OP_RESET command. As part of handling the reset command,
firmware initializes the hardware and data path and raises the alive
interrupt. Upon receiving the alive interrupt, the driver must enable
the data path and grant RX buffers to the firmware before sending any
commands.
The alive context maintained in the driver must be updated before
sending BTINTEL_HCI_OP_RESET or HCI_OP_RESET to prevent a potential race
condition where the context is also updated in the threaded IRQ.
The issue was observed in a stress reboot usecase (1/25) using "sudo
reboot" command where the firmware download was failing as the driver
was not granting RX buffer to firmware due to race condition.
Bluetooth: hci0: API lock is disabled
Bluetooth: hci0: Debug lock is disabled
Bluetooth: hci0: Minimum firmware build 1 week 10 2014
Bluetooth: hci0: Bootloader timestamp 2023.43 buildtype 1 build 11631
Bluetooth: hci0: Found device firmware: intel/ibt-00a0-00a1-iml.sfi
Bluetooth: hci0: Boot Address: 0xb0301000
Bluetooth: hci0: Firmware Version: 167-12.25
Bluetooth: hci0: Waiting for firmware download to complete
Bluetooth: hci0: Firmware loaded in 99902 usecs
Bluetooth: hci0: Alive context: fw_dl old_boot_stage: 0xa0db0003
new_boot_stage: 0xa0db0003
Bluetooth: hci0: sent cmd: 0xfc01 alive context changed:
fw_dl -> intel_reset1
Bluetooth: hci0: Waiting for device to boot
Bluetooth: hci0: Device boot timeout
Bluetooth: hci0: Firmware download retry count: 1
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The firmware raises an alive interrupt upon receiving the HCI_RESET or
BTINTEL_HCI_OP_RESET (Intel reset - 0xfc01) command. This change fixes
the driver to properly wait for the alive interrupt to avoid driver
sending commands to firmware before it is ready to process.
For details on the handshake between the driver and firmware, refer to
commit 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between
driver and firmware").
As the driver needs to handle two interrupts for HCI_OP_RESET and
BTINTEL_HCI_OP_RESET, the firmware ensures that the TX completion
interrupt is always followed by the alive interrupt.
Fixes: 05c200c8f0 ("Bluetooth: btintel_pcie: Add handshake between driver and firmware")
Signed-off-by: Sai Teja Aluvala <aluvala.sai.teja@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Sort WCN6855 device IDs to more easily manage them.
Signed-off-by: Zijun Hu <Zijun.Hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There are custom-made firmwares based on board ID for a given QCA BT
chip sometimes, and they are different with existing firmwares and put
in a separate subdirectory to avoid conflict, for example:
QCA2066, as a variant of WCN6855, has firmwares under 'qca/QCA2066/'
of linux-firmware repository.
Support downloading custom-made firmwares based on a table newly added.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds uevents which will be generated whenever FW dump is triggered,
FW dump is complete and FW (re)download is done.
This feature is needed for IW612 chipset, which is a tri-radio chipset,
where WLAN runs on CPU1 and BT and Zigbee runs on CPU2.
Currently, whenever BT FW crashes, and FW dump is in progress, there is
no way for 15.4 application to know that CPU2 is in bad state, and when
it will be recovered.
With the help of these uevents and udev rules, the 15.4 app, or any
userspace application can be alerted whenever CPU2 goes in bad state and
recoveres after BTNXPUART reloads the firmware.
[ 334.255154] Bluetooth: hci0: ==== Start FW dump ===
[ 334.261003] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_ACTIVE ===
[ 351.486048] Bluetooth: hci0: ==== FW dump complete ===
[ 351.491356] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_DUMP_DONE ===
[ 352.028974] Bluetooth: hci0: ChipID: 7601, Version: 0
[ 352.034490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
[ 353.979977] Bluetooth: hci0: FW Download Complete: 417064 bytes
[ 355.197222] Bluetooth: hci0: ==== Send uevent: BTNXPUART_DEV=serial0-0:BTNXPUART_STATE=FW_READY ===
Tested this change by creating a simple udev rule to store the
BTNXPUART_STATE value in a ~/<BTNXPUART_DEV>/state file, and running
15.4 traffic.
The 15.4 packets were sent over SPI only when BTNXPUART_STATE was
FW_READY.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds proper handling for the independent reset command sent by the
driver after FW dump is complete.
In normal scenario, the independent reset vendor command gives a success
response before jumping to bootcode.
However, when FW goes in a bad state, and sends out FW dump packets, the
independent reset command does not get any response from the controller.
[ 159.807732] Bluetooth: hci0: ==== Start FW dump ===
[ 180.759060] Bluetooth: hci0: ==== FW dump complete ===
[ 182.779208] Bluetooth: hci0: command 0xfcfc tx timeout
[ 183.364974] Bluetooth: hci0: ChipID: 7601, Version: 0
[ 183.368490] Bluetooth: hci0: Request Firmware: nxp/uartspi_n61x_v1.bin.se
[ 184.679977] Bluetooth: hci0: FW Download Complete: 417064 bytes
[ 187.963102] Bluetooth: hci0: Opcode 0x0c03 failed: -110
As a fix for such scenario, the independent reset vendor command is sent
using the __hci_cmd_send() API, which does not expect any response for
vendor commands.
__hci_cmd_send is non blocking, so before the tx_work is scheduled, it
sometimes gets canceled and 3F|FC command is never sent. Adding a small
delay after __hci_cmd_send allows the command to be sent to the
controller.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Tested-by: Jean-Yves Salaün <jean-yves.salaun@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use macro for Intel Reset command (0xfc01) instead of hard coded value.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Avoid potential NULL pointer dereference by checking the return value of
kmalloc and handling allocation failure properly.
Fixes: 7d70989fce ("Bluetooth: btusb: Add HCI Drv commands for configuring altsetting")
Signed-off-by: Zhongqiu Han <quic_zhonhan@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
NXP bluetooth chip shares power supply and reset gpio with a WLAN
chip. Add support for power supply and reset and enforce powerup
sequence:
- apply power supply
- deassert reset/powerdown
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for 4000000 as secondary baudrate.
This value is selected from device tree property "max-speed"
which is then used to download FW chunks, and as operational baudrate after
HCI initialization is done.
Earlier, the secondary baudrate was fixed to 3000000 in driver, but now
with "max-speed" property, this secondary baudrate can be set to
4000000.
The secondary baudrate is set by the driver by sending a vendor command
(3F 09) to the firmware, with secondary baudrate parameter, in
nxp_post_init().
Any other value set for max-speed other than 3000000 or 4000000 will
default to 3000000, which is supported by all legacy and new NXP chipsets.
This feature is applicable for all new V3 bootloader chips and w8987 V1
bootloader chip.
This property does not apply for w8997 compatible device, since it
downloads a helper.bin FW file that sets secondary baudrate as 3000000
only.
The switch to 4000000 baudrate is validated using a Saleae Logic Analyzer
and imx8m-mini with AW693 M.2 module.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Enable ISO data packet RX for LE audio.
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This rewords the term restart with recovery since the intend is for
hardware recovery not a regular restart, also remove some debug logs
which might just clutter the output informing the recovery counter which
isn't really useful for regular users.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver supports Function Level Reset (FLR) to recover the controller
upon hardware exceptions or hci command timeouts. FLR is triggered only
when no prior reset has occurred within the retry window, with a maximum
of one FLR allowed within this window.
This patch is tested by,
echo 1 > /sys/class/bluetooth/hciX/reset
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
For GF variant of WCN6855 without board ID programmed
btusb_generate_qca_nvm_name() will chose wrong NVM
'qca/nvm_usb_00130201.bin' to download.
Fix by choosing right NVM 'qca/nvm_usb_00130201_gf.bin'.
Also simplify NVM choice logic of btusb_generate_qca_nvm_name().
Fixes: d6cba4e6d0 ("Bluetooth: btusb: Add support using different nvm for variant WCN6855 controller")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The 'quirks' member already ran out of bits on some platforms some time
ago. Replace the integer member by a bitmap in order to have enough bits
in future. Replace raw bit operations by accessor macros.
Fixes: ff26b2dd65 ("Bluetooth: Add quirk for broken READ_VOICE_SETTING")
Fixes: 127881334e ("Bluetooth: Add quirk for broken READ_PAGE_SCAN_TYPE")
Suggested-by: Pauli Virtanen <pav@iki.fi>
Tested-by: Ivan Pravdin <ipravdin.official@gmail.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Due to what seem to be a bug with variant version returned by some
firmwares the code may set hdev->classify_pkt_type with
btintel_classify_pkt_type when in fact the controller doesn't even
support ISO channels feature but may use the handle range expected from
a controllers that does causing the packets to be reclassified as ISO
causing several bugs.
To fix the above btintel_classify_pkt_type will attempt to check if the
controller really supports ISO channels and in case it doesn't don't
reclassify even if the handle range is considered to be ISO, this is
considered safer than trying to fix the specific controller/firmware
version as that could change over time and causing similar problems in
the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=219553
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2100565
Link: https://github.com/StarLabsLtd/firmware/issues/180
Fixes: f25b7fd36c ("Bluetooth: Add vendor-specific packet classification for ISO data")
Cc: stable@vger.kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Sean Rhodes <sean@starlabs.systems>
Some modules have BT_EN enabled via a hardware pull-up,
meaning it is not defined in the DTS and is not controlled
through the power sequence. In such cases, fall through
to follow the legacy flow.
Signed-off-by: Shuai Zhang <quic_shuaz@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
During firmware download, if an error occurs, interrupts must be
disabled, synchronized, and re-enabled before retrying the download.
This change ensures proper interrupt handling to prevent race
conditions.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent invalid
routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused transient
packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmhK/3IACgkQMUZtbf5S
IruE5A//RdwiBW/pqoMIiRKLA3HZeUA/beYOl4DwVf8WFQNUIqdboeAi6k4yFrS+
SykKN0s1z8fW45lA46iFv3sR0QKYGln/v/cANsqojYqKBD3PF42dRifFlEAIz2M5
fnXK1VHPJOFK/OBOyKiiW3R6mFv+v9epZM8BKED77vFy7osDV2zkObePeE8/34B7
yVAr6JNTpB5Ex4ziG+e/6tFF6IX9RJLBl4fkRRynLDSsb1NFuy39LxPsxRQPxnzo
tlfHfxEFl5qDNGondUoSxmp38HoO6MRofWp1d1GZoBbTXi0gXV26I5WaaBHBqPkm
jZ7AtIMQq2+JuEg0y4dFFRehZLwLEMuhvlbacbIOKNBngVIsploBzvbG3ntWuUa4
Z5VFayQXumsHB5g7+vEFK6vCPaIpatKt419JsFXogNvVmmQzghALFlSymm/WbyGL
Bj3R448xGDJw+2zDAXSH/nMMHkRaQd2Ptj2czvJ0Y7Fj8bxJgH0okaHOBrk9RQTQ
bdUGCiMY84p6WI7rKDkFyyohMxppdYsY8A9hSdGgpqvu7dZi5yGmzz1Sp9+uSfSF
Lj61am4LSvRsIuTP5cdqmTBn3mZS5R49hvJsFddgXRhF+Y9gB7LSm0sypZbuOEKD
m9ijKcNETglzer0iMCwAVrIbDHGjqqHS74DkRzsuPsQ8kaCjsno=
=0mtm
-----END PGP SIGNATURE-----
Merge tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth and wireless.
Current release - regressions:
- af_unix: allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD
Current release - new code bugs:
- eth: airoha: correct enable mask for RX queues 16-31
- veth: prevent NULL pointer dereference in veth_xdp_rcv when peer
disappears under traffic
- ipv6: move fib6_config_validate() to ip6_route_add(), prevent
invalid routes
Previous releases - regressions:
- phy: phy_caps: don't skip better duplex match on non-exact match
- dsa: b53: fix untagged traffic sent via cpu tagged with VID 0
- Revert "wifi: mwifiex: Fix HT40 bandwidth issue.", it caused
transient packet loss, exact reason not fully understood, yet
Previous releases - always broken:
- net: clear the dst when BPF is changing skb protocol (IPv4 <> IPv6)
- sched: sfq: fix a potential crash on gso_skb handling
- Bluetooth: intel: improve rx buffer posting to avoid causing issues
in the firmware
- eth: intel: i40e: make reset handling robust against multiple
requests
- eth: mlx5: ensure FW pages are always allocated on the local NUMA
node, even when device is configure to 'serve' another node
- wifi: ath12k: fix GCC_GCC_PCIE_HOT_RST definition for WCN7850,
prevent kernel crashes
- wifi: ath11k: avoid burning CPU in ath11k_debugfs_fw_stats_request()
for 3 sec if fw_stats_done is not set"
* tag 'net-6.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
selftests: drv-net: rss_ctx: Add test for ntuple rules targeting default RSS context
net: ethtool: Don't check if RSS context exists in case of context 0
af_unix: Allow passing cred for embryo without SO_PASSCRED/SO_PASSPIDFD.
ipv6: Move fib6_config_validate() to ip6_route_add().
net: drv: netdevsim: don't napi_complete() from netpoll
net/mlx5: HWS, Add error checking to hws_bwc_rule_complex_hash_node_get()
veth: prevent NULL pointer dereference in veth_xdp_rcv
net_sched: remove qdisc_tree_flush_backlog()
net_sched: ets: fix a race in ets_qdisc_change()
net_sched: tbf: fix a race in tbf_change()
net_sched: red: fix a race in __red_change()
net_sched: prio: fix a race in prio_tune()
net_sched: sch_sfq: reject invalid perturb period
net: phy: phy_caps: Don't skip better duplex macth on non-exact match
MAINTAINERS: Update Kuniyuki Iwashima's email address.
selftests: net: add test case for NAT46 looping back dst
net: clear the dst when changing skb protocol
net/mlx5e: Fix number of lanes to UNKNOWN when using data_rate_oper
net/mlx5e: Fix leak of Geneve TLV option object
net/mlx5: HWS, make sure the uplink is the last destination
...
Move this API to the canonical timer_*() namespace.
[ tglx: Redone against pre rc1 ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/aB2X0jCKQO56WdMt@gmail.com
Modify the driver to post 3 fewer buffers than the maximum rx buffers
(64) allowed for the firmware. This change mitigates a hardware issue
causing a race condition in the firmware, improving stability and data
handling.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This change addresses latency issues observed in HID use cases where
events arrive in bursts. By increasing the Rx descriptor count to 64,
the firmware can handle bursty data more effectively, reducing latency
and preventing buffer overflows.
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The driver was posting only 6 rx buffers, despite the maximum rx buffers
being defined as 16. Having fewer RX buffers caused firmware exceptions
in HID use cases when events arrived in bursts.
Exception seen on android 6.12 kernel.
E Bluetooth: hci0: Received hw exception interrupt
E Bluetooth: hci0: Received gp1 mailbox interrupt
D Bluetooth: hci0: 00000000: ff 3e 87 80 03 01 01 01 03 01 0c 0d 02 1c 10 0e
D Bluetooth: hci0: 00000010: 01 00 05 14 66 b0 28 b0 c0 b0 28 b0 ac af 28 b0
D Bluetooth: hci0: 00000020: 14 f1 28 b0 00 00 00 00 fa 04 00 00 00 00 40 10
D Bluetooth: hci0: 00000030: 08 00 00 00 7a 7a 7a 7a 47 00 fb a0 10 00 00 00
D Bluetooth: hci0: 00000000: 10 01 0a
E Bluetooth: hci0: ---- Dump of debug registers —
E Bluetooth: hci0: boot stage: 0xe0fb0047
E Bluetooth: hci0: ipc status: 0x00000004
E Bluetooth: hci0: ipc control: 0x00000000
E Bluetooth: hci0: ipc sleep control: 0x00000000
E Bluetooth: hci0: mbox_1: 0x00badbad
E Bluetooth: hci0: mbox_2: 0x0000101c
E Bluetooth: hci0: mbox_3: 0x00000008
E Bluetooth: hci0: mbox_4: 0x7a7a7a7a
Signed-off-by: Chandrashekar Devegowda <chandrashekar.devegowda@intel.com>
Signed-off-by: Kiran K <kiran.k@intel.com>
Fixes: c2b636b3f7 ("Bluetooth: btintel_pcie: Add support for PCIe transport")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Commit 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL
returned by gpiod_get_optional()") accidentally changed the prevous
behavior where power control would be disabled without the BT_EN GPIO
only on QCA_WCN6750 and QCA_WCN6855 while also getting the error check
wrong. We should treat every IS_ERR() return value from
devm_gpiod_get_optional() as a reason to bail-out while we should only
set power_ctrl_enabled to false on the two models mentioned above. While
at it: use dev_err_probe() to save a LOC.
Cc: stable@vger.kernel.org
Fixes: 3d05fc8223 ("Bluetooth: qca: set power_ctrl_enabled on NULL returned by gpiod_get_optional()")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Hsin-chen Chuang <chharry@chromium.org>
Reviewed-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Return value of devm_request_irq() must be checked (function is even
annotated) and without it clang W=1 complains:
btnxpuart.c:494:6: error: unused variable 'ret' [-Werror,-Wunused-variable]
Setting up wakeup IRQ handler is not really critical, because the
handler is empty, so just log the informational message so user could
submit proper bug report and silences the clang warning.
Fixes: c50b56664e ("Bluetooth: btnxpuart: Implement host-wakeup feature")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Since the size of struct btintel_dsbr is already known, we can just
start there instead of querying the EFI variable size. If the final
result doesn't match what we expect also fail. This fixes a stack buffer
overflow when the EFI variable is larger than struct btintel_dsbr.
Reported-by: zepta <z3ptaa@gmail.com>
Closes: https://lore.kernel.org/all/CAPBS6KoaWV9=dtjTESZiU6KK__OZX0KpDk-=JEH8jCHFLUYv3Q@mail.gmail.com
Fixes: eb9e749c01 ("Bluetooth: btintel: Allow configuring drive strength of BRI")
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Use skb_pull() and skb_pull_data() to safely parse QCA dump packets.
This avoids direct pointer math on skb->data, which could lead to
invalid access if the packet is shorter than expected.
Fixes: 20981ce2d5 ("Bluetooth: btusb: Add WCN6855 devcoredump support")
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit b16b327edb.
The sysfs node introduced by this patch could potentially race with user
space. The original motivation - Support configuring altsetting from the
user space will be added by another series.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reverts commit 75ddcd5ad4.
This patch doesn't work quite well - It's observed that with this patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Although commit 75ddcd5ad4 ("Bluetooth: btusb: Configure altsetting
for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out
SCO data through USB Bluetooth chips, it's observed that with the patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
To address the issue above one needs to reset the altsetting back to
zero when there is no active SCO connection, which is the same as the
BlueZ behavior, and another benefit is the bus doesn't need to reserve
bandwidth when no SCO connection.
This patch adds "Supported Altsettings" and "Switch Altsetting" commands
that allow the user space program to configure the altsetting freely.
This patch is tested on ChromeOS devices. The USB Bluetooth models
(CVSD, TRANS alt3, and TRANS alt6) could pass the stress HFP test narrow
band speech and wide band speech.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Although commit 75ddcd5ad4 ("Bluetooth: btusb: Configure altsetting
for HCI_USER_CHANNEL") has enabled the HCI_USER_CHANNEL user to send out
SCO data through USB Bluetooth chips, it's observed that with the patch
HFP is flaky on most of the existing USB Bluetooth controllers: Intel
chips sometimes send out no packet for Transparent codec; MTK chips may
generate SCO data with a wrong handle for CVSD codec; RTK could split
the data with a wrong packet size for Transparent codec; ... etc.
To address the issue above one needs to reset the altsetting back to
zero when there is no active SCO connection, which is the same as the
BlueZ behavior, and another benefit is the bus doesn't need to reserve
bandwidth when no SCO connection.
This patch adds the infrastructure that allow the user space program to
talk to Bluetooth drivers directly:
- Define the new packet type HCI_DRV_PKT which is specifically used for
communication between the user space program and the Bluetooth drviers
- hci_send_frame intercepts the packets and invokes drivers' HCI Drv
callbacks (so far only defined for btusb)
- 2 kinds of events to user space: Command Status and Command Complete,
the former simply returns the status while the later may contain
additional response data.
Cc: chromeos-bluetooth-upstreaming@chromium.org
Fixes: b16b327edb ("Bluetooth: btusb: add sysfs attribute to control USB alt setting")
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This implements host wakeup feature by reading the device tree property
wakeup-source and 'wakeup' interrupt, and nxp,wakeout-pin, and configuring
it as a FALLING EDGE triggered interrupt.
When host is suspended, a trigger from the WAKE_OUT pin of the
controller wakes it up.
To enable this feature, both device tree properties are needed to be
defined.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
release_firmware() checks for NULL pointers internally.
Remove unneeded NULL check for fmw here.
Signed-off-by: Chen Ni <nichen@iscas.ac.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device can be unbound or probe can fail, so driver must also release
memory for the wakeup source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Device can be unbound or probe can fail, so driver must also release
memory for the wakeup source.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
