The auto counter reload feature requires an event flag to indicate an
auto counter reload group, which can only be scheduled on specific
counters that enumerated in CPUID. However, the hw_perf_event.flags has
run out on X86.
Two solutions were considered to address the issue.
- Currently, 20 bits are reserved for the architecture-specific flags.
Only the bit 31 is used for the generic flag. There is still plenty
of space left. Reserve 8 more bits for the arch-specific flags.
- Add a new X86 specific hw_perf_event.flags1 to support more flags.
The former is implemented. Enough room is still left in the global
generic flag.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Thomas Falcon <thomas.falcon@intel.com>
Link: https://lkml.kernel.org/r/20250327195217.2683619-4-kan.liang@linux.intel.com
The counters snapshotting is a new adaptive PEBS extension, which can
capture programmable counters, fixed-function counters, and performance
metrics in a PEBS record. The feature is available in the PEBS format
V6.
The target counters can be configured in the new fields of MSR_PEBS_CFG.
Then the PEBS HW will generate the bit mask of counters (Counters Group
Header) followed by the content of all the requested counters into a
PEBS record.
The current Linux perf sample read feature can read all events in the
group when any event in the group is overflowed. But the rdpmc in the
NMI/overflow handler has a small gap from overflow. Also, there is some
overhead for each rdpmc read. The counters snapshotting feature can be
used as an accurate and low-overhead replacement.
Extend intel_update_topdown_event() to accept the value from PEBS
records.
Add a new PEBS_CNTR flag to indicate a sample read group that utilizes
the counters snapshotting feature. When the group is scheduled, the
PEBS configure can be updated accordingly.
To prevent the case that a PEBS record value might be in the past
relative to what is already in the event, perf always stops the PMU and
drains the PEBS buffer before updating the corresponding event->count.
Suggested-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250121152303.3128733-4-kan.liang@linux.intel.com
The branch counters logging (A.K.A LBR event logging) introduces a
per-counter indication of precise event occurrences in LBRs. It can
provide a means to attribute exposed retirement latency to combinations
of events across a block of instructions. It also provides a means of
attributing Timed LBR latencies to events.
The feature is first introduced on SRF/GRR. It is an enhancement of the
ARCH LBR. It adds new fields in the LBR_INFO MSRs to log the occurrences
of events on the GP counters. The information is displayed by the order
of counters.
The design proposed in this patch requires that the events which are
logged must be in a group with the event that has LBR. If there are
more than one LBR group, the counters logging information only from the
current group (overflowed) are stored for the perf tool, otherwise the
perf tool cannot know which and when other groups are scheduled
especially when multiplexing is triggered. The user can ensure it uses
the maximum number of counters that support LBR info (4 by now) by
making the group large enough.
The HW only logs events by the order of counters. The order may be
different from the order of enabling which the perf tool can understand.
When parsing the information of each branch entry, convert the counter
order to the enabled order, and store the enabled order in the extension
space.
Unconditionally reset LBRs for an LBR event group when it's deleted. The
logged counter information is only valid for the current LBR group. If
another LBR group is scheduled later, the information from the stale
LBRs would be otherwise wrongly interpreted.
Add a sanity check in intel_pmu_hw_config(). Disable the feature if other
counter filters (inv, cmask, edge, in_tx) are set or LBR call stack mode
is enabled. (For the LBR call stack mode, we cannot simply flush the
LBR, since it will break the call stack. Also, there is no obvious usage
with the call stack mode for now.)
Only applying the PERF_SAMPLE_BRANCH_COUNTERS doesn't require any branch
stack setup.
Expose the maximum number of supported counters and the width of the
counters into the sysfs. The perf tool can use the information to parse
the logged counters in each branch.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-5-kan.liang@linux.intel.com
Currently, branch_sample_type !=0 is used to check whether a branch
stack setup is required. But it doesn't check the sample type,
unnecessary branch stack setup may be done for a counting event. E.g.,
perf record -e "{branch-instructions,branch-misses}:S" -j any
Also, the event only with the new PERF_SAMPLE_BRANCH_COUNTERS branch
sample type may not require a branch stack setup either.
Add a new flag NEEDS_BRANCH_STACK to indicate whether the event requires
a branch stack setup. Replace the needs_branch_stack() by checking the
new flag.
The counting event check is implemented here. The later patch will take
the new PERF_SAMPLE_BRANCH_COUNTERS into account.
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20231025201626.3000228-2-kan.liang@linux.intel.com
Ensure all platform specific event flags are within PERF_EVENT_FLAG_ARCH.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: James Clark <james.clark@arm.com>
Link: https://lkml.kernel.org/r/20220907091924.439193-5-anshuman.khandual@arm.com
