These clocks are not used by the dwc3-xilinx driver except to
enable/disable them. Move them to the dwc3 node so its driver can use
them to configure the reference clock period.
Tested-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127200636.1456175-7-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cadence GEM/MACB driver now utilizes the platform-level reset on the
ZynqMP platform. Add reset definitions to the ZynqMP platform device
tree to allow this to be used.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ZynqMP dma engines are actually dma-controllers as specified by the
device tree binding. Rename the device tree nodes accordingly.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20220112151541.1328732-4-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Property #stream-id-cells is legacy leftover and isn't currently
documented nor used.
Signed-off-by: David Heidelberg <david@ixit.cz>
Link: https://lore.kernel.org/r/20211208184846.101166-1-david@ixit.cz
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are couple of revisions of SOMs (k26) and associated carrier cards
(kv260).
SOM itself has two major versions:
sm-k26 - SOM with EMMC
smk-k26 - SOM without EMMC used on starter kit with preprogrammed firmware
in QSPI.
SOMs are describing only devices available on the SOM or connections which
are described in specification (for example UART, fwuen).
When SOM boots out of QSPI it uses limited number of peripherals defined by
the specification and present in sm(k)-k26 dtses.
Then a carrier card (CC) detection is happening and DT overlay is applied
to brings new functionality. That's why DT overlays are used. The name is
composed together with SOM name and CC name that's why DT overlays with
these names are generated to make sure they can be used together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1ba32590670434b650bacf6410a65579dd30b38b.1632294439.git.michal.simek@xilinx.com
Remove is-dual not documented property and also update comment about QSPI
sizes to reflect dual configuration as 16MB + 16MB.
Only single configuration is supported now.
Reported-by: Quanyang Wang <quanyang.wang@windriver.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/876c53b92f99623bae45d5c0c5ae79ee3e24f745.1628239345.git.michal.simek@xilinx.com
zcu102 rev1.1 compare to rev1.0 is using by default different DDR memory
which requires different configuration. The reason for adding this file to
Linux kernel is that U-Boot fdtfile variable is composed based on board
revision (in eeprom) and dtb file should exist in standard distibutions for
passing it to Linux kernel.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/38bbbeb885f4d9ba466c43ab9b4d25190a3552fb.1623684253.git.michal.simek@xilinx.com
As per the design specification
"The 16-bit Seconds Calibration Value represents the number of
Oscillator Ticks that are required to measure the largest time
period that is less than or equal to 1 second.
For an oscillator that is 32.768 KHz, this value will be 0x7FFF."
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0d36d9fe999ff82f10d42ab5fc0d1e907c26ac34.1623684253.git.michal.simek@xilinx.com
This patch adds reset-on-timeout to FPD WDT which will trigger an
interrupt to PMU when watchdog expiry happens and PMU takes the
necessary action. If this property is not enabled, reason will not be
known when watchdog expiry happens.
This patch also modifies the default timeout to 60 seconds. Reason is
that if u-boot enables WDT, it will set the timeout to 10 seconds and
this is not enough to boot till Linux and start the WDT application in
Linux. 60 seconds is the maximum safest value to boot till Linux and
start the WDT application.
Users need to change this timeout value to fit their needs.
Signed-off-by: Mounika Grace Akula <mounika.grace.akula@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/5848a81447921240fddfe2f5749ae0746fcbbdbd.1623684253.git.michal.simek@xilinx.com
In kernel 5.4, support has been added for reading MTD devices via the nvmem
API.
For this the mtd devices are registered as read-only NVMEM providers under
sysfs with the same name as the flash partition label property.
So if flash partition label property of multiple flash devices are
identical then the second mtd device fails to get registered as a NVMEM
provider.
This patch fixes the issue by having different label property for different
flashes.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/6c4b9b9232b93d9e316a63c086540fd5bf6b8687.1623684253.git.michal.simek@xilinx.com
The function of_i2c_get_board_info will call of_modalias_node to check
if a device_node contains "compatible" string. But for the device si5328
at zcu102/zcu106 boards, there is no proper DT bindings for them. So remove
si5328 device nodes from dts files to eliminate the error info in the boot
message:
i2c i2c-10: of_i2c: modalias failure on /axi/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
i2c i2c-10: Failed to create I2C device for /axi/i2c@ff030000/i2c-mux@74/i2c@4/clock-generator@69
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210308115437.2232847-1-quanyang.wang@windriver.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The DisplayPort DMA controller (DPDMA) is located in the same power
domain as the DisplayPort Subsystem (DPSUB). Specify the power domain in
the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20210306230915.14979-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
