Add bootph-all property to sysinfo EEPROM on Renesas R-Car Gen3
Salvator-X(S), ULCB, Condor, Ebisu, Draak boards. The sysinfo
EEPROM is used by U-Boot early on, mark it using the bootph-all
property. No functional change for the Linux kernel, this only
reduces the divergence of DTs between U-Boot and Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250608215212.1619182-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT. Add bootph-all for all nodes that are used in the
bootloader on Renesas R-Car SoCs.
All SoC require CPG clock and its input clock, RST Reset, PFC pin
control and PRR ID register access during all stages of the boot
process, those are marked using bootph-all property, and so is the SoC
bus node which contains these IP.
Each board console UART is also marked as bootph-all to make it
available in all stages of the boot process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250209180616.160253-2-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use the more concise interrupts-extended property to fully describe the
interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> # G2L family and G3S
Link: https://lore.kernel.org/e9db8758d275ec63b0d6ce086ac3d0ea62966865.1728045620.git.geert+renesas@glider.be
The I2C EEPROM U197 on Condor is also present on Condor-I, but it was
moved to the other side of the bi-directional voltage-level translator
on I2C bus zero, and relabeled to U230.
Move it to condor-common.dtsi to make it available on Condor-I, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/33a1ec9ee8fff7708f699c668d7399fde2b46553.1716455483.git.geert+renesas@glider.be
We have V3H Condor board, and will have V3H2 Condor-I board.
This patch adds condor-common.dtsi to share the common settings
between these boards.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871qsy625m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
