Enable HDMI output on i.MX8MP DHCOM PDK2 and PDK3. The I2C5 on PDK2 and
I2C mux port 1 on PDK3 respectively are used in regular I2C mode instead
of HDMI DDC mode to permit connection of other I2C devices on those buses.
The pinctrl_hdmi node is part of the SoM DTSI already.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The production PDK3 carrier board rev.200 contains additional GPIO
expander to control power and reset signals for each CSI2 plug
separately. Describe this expander in the carrier board DT. The
label is used by sensor DTOs to reference the expander and its
signals.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit a4dca89fe8.
Marek reported:
"This patch breaks USB-C port on this board.
If I plug in USB-C storage device, it is not detected. If I revert this
patch, it is detected.
Please drop this patch for now."
Revert it to avoid the regression.
Reported-by: Marek Vasut <marex@denx.de>
Closes: https://lore.kernel.org/linux-arm-kernel/623c294a-5c53-4e01-acbf-104acc180e14@denx.de/T/#u
Fixes: a4dca89fe8 ("arm64: dts: imx8mp-dhcom-pdk3: Describe the USB-C connector")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Describe the PTN5150 USB-C connector to improve the devicetree description
and fix the following dt-schema warning:
imx8mp-dhcom-pdk3.dtb: typec@3d: 'port' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/extcon/extcon-ptn5150.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In case the i.MX8MP DHCOM rev.100 has been populated on the PDK3
carrier board, the on-SoM PHY PHYAD1 signal has been pulled high
by the carrier board and changed the PHY MDIO address from 5 to 7.
This has been fixed on production rev.200 SoM by additional buffer
on the SoM PHYAD/LED signals, remove the workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove the connector as well as all the links and only connect the
PTN5150 with xHCI controller. This is sufficient to implement the
role switching.
Furthermore, this makes resume work without hanging. Without this
patch, the platform would hang on resume of 'connector'.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SAI I2S and audio bindings on MX8MP DHCOM PDK2 and PDK3.
The VDDA is supplied from on-carrier-board regulator, the VDDIO
is supplied from always-on on-SoM regulator. Except for different
I2C bus used to connect the codec, the implementation is virtually
identical on both carrier boards.
Align regulator-avdd name to regulator-3p3vdd on PDK3, since this
is the VDDA supply and it is the same on both carrier boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PDK3 carrier board contains a PCIe clock generator which is used to
supply the PCIe clock lanes. This generator is always on, unless external
CLKREQ signal toggles an output off, but this is handled in hardware. The
generator does however have I2C interface, describe it in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR, CAN, M.2 E-Key or M.2 M-Key PCIe, USB .
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
