The "clock-latency" property is part of the deprecated opp-v1 binding
and is redundant if the opp-v2 table has equal or larger values in any
"clock-latency-ns". Add any missing "clock-latency-ns" properties and
remove "clock-latency".
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250410-dt-cpu-schema-v2-11-63d7dc9ddd0a@kernel.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Use the new PWM controller binding which now relies on passing all
clock inputs available on the SoC (instead of passing the "wanted"
clock input for a given board).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20241227212514.1376682-6-martin.blumenstingl@googlemail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable audio capture frontends and a tdm decoder.
This makes it possible to loopback the audio played on the hdmi codec,
which is the only output interface at the moment.
Of course, one TODDR device would be enough to do that but since
the 3 FRDDRs are enabled on the playback side, let's do the same on the
capture side.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210429084253.59692-1-jbrunet@baylibre.com
The sound card definition should have been removed when the common
definition was added to the vim3 dtsi but this slips through.
Remove it now.
Fixes: 7c9c06246c ("arm64: dts: meson: vim3: make sound card common to all variants")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200828154435.419561-1-jbrunet@baylibre.com
Similar to other G12B devices using the W400 dtsi, I see reports of mmc0
tuning errors on VIM3 after a few hours uptime:
[12483.917391] mmc0: tuning execution failed: -5
[30535.551221] mmc0: tuning execution failed: -5
[35359.953671] mmc0: tuning execution failed: -5
[35561.875332] mmc0: tuning execution failed: -5
[61733.348709] mmc0: tuning execution failed: -5
I do not see the same on VIM3L, so remove sd-uhs-sdr50 from the common dtsi
to silence the error, then (re)add it to the VIM3L dts.
Fixes: 4f26cc1c96 ("arm64: dts: khadas-vim3: move common nodes into meson-khadas-vim3.dtsi")
Fixes: 700ab8d839 ("arm64: dts: khadas-vim3: add support for the SM1 based VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200721015950.11816-1-christianshewitt@gmail.com
Add initial audio support limited to HDMI i2s, copying the config
from the existing VIM3 device-tree.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20200718072532.8427-3-christianshewitt@gmail.com
The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
The needed DT configuration when the MCU is configured to mux
the PCIe/USB3.0 differential lines to the M.2 Key M slot is
added commented and may be uncommented to disable USB3.0 from the
USB Complex and enable the PCIe controller.
The End User is not expected to uncomment the following except for
testing purposes, but instead rely on the firmware/bootloader to
update these nodes accordingly if PCIe mode is selected by the MCU.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add the Amlogic SM1 based Khadas VIM3L, sharing all the same features
as the G12B based VIM3, but:
- a different DVFS support since only a single cluster is available
- audio is still not available on SM1
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
